Function keys
HDS-5/5m & HDS-7/7m
Quick Start Guide
Arrow
Keypad
PAGES
WPT
FIND
Activates cursor on Chart page. Press up, down, left or right to move
the cursor.
ZOUT
ENTER
MENU
Press to select the page (screen) to display or to access utilities such as
the waypoints list and celestial table. Press and hold to switch control
between the panels and combo (split screen) pages.
Press to save a waypoint at your current GPS position. Press and hold
to search for waypoints and other points of interest (POI's) or quickly
access waypoints, routes and trails..
Zooms out the Radar, Sonar and Chart pages.
Zooms in the Radar, Sonar and Chart pages.
ZIN
Press to return to a previous screen, clear data and
EXIT
close menus. Pressing Exit on the Chart page will
quickly switch between displaying the boat symbol
and the last cursor position.
Press to save data, change values and accept menu
commands; also acts as a short cut key for important
functions such as saving a waypoint at the cursor
position on the Chart page.
Accesses the features available on each page.
LIGHT
POWER
Press to turn the unit on, adjust the backlight or place the unit in low
power (standby) mode. Press and hold to turn the unit off.
Creating a Man Overboard (MOB) position:
Press the ZOUT and ZIN keys at the same time to create a MOB waypoint with a
line to your boat position.
To view a page:
Pages screen
1. From any screen press PAGES to access the Pages screen.
Select the desired page display. 2.
To adjust Panel sizes on a Combo page:
1. From the Pages screen, select the desired Combo page and press
the MENU key. Selecting Sonar + Chart will display a Sonar-Chart
combo page.
Select 2. Adjust panel sizes. Use the on-screen button to adjust the
panel size.
NOTE: Hold down the PAGES key to switch active panels
when viewing a combo page.
To add a Data overlay to a page:
1. To add/edit data overlay, select the
desired page from the pages screen
and press MENU.
Select 2. Edit data overlay and press
ENTER.
When the page appears press 3. ENTER
to select data or MENU to access the
edit overlay menu.
Cursor depth
Sonar (Sonar units only)
Fish arches
Cursor
Brush pile
Information at
cursor's position.
Press the keypad to the left to scroll the Sonar page back to view previous
sonar returns. When the cursor is onscreen the sonar does not show real
time sonar returns. Press EXIT to return to normal operation.
Range scale
History bar
Amplitude
scope
Transducer Type
Selecting the proper transducer type from the sonar installation menu helps optimize
HDS performance by enabling settings (temperature and frequency) and menu
options specic to your transducer.
To select a Transducer Type:
Press 1. MENU twice.
Select 2. Sonar and press ENTER.
Select 3. Installation and press ENTER.
Select the desired transducer type 4.
and press ENTER.
Highlight 5. Save and press ENTER.
Transducer type menu
Fishing Modes
Enhances the performance of your unit by providing preset packages of sonar
settings geared to specic shing conditions.
Fishing
Mode
General Use ≤1,000 ft 50% Ping speed Bottom brown/ blue background
Shallow Water ≤ 60 ft 75% Ping speed bottom brown/white background
Fresh Water ≤ 400 ft 50% Ping speed bottom brown/white background
Deep Water ≥ 1,000 ft 50% Ping speed Deep Blue
Slow Trolling ≤ 400 ft 50% Ping speed Bottom brown/white background
Fast Trolling ≤ 400 ft Lower chart speed Bottom brown/white background
Clear Water ≤ 400 ft 50% Ping speed Bottom brown/white background
Ice Fishing ≤ 400 ft
Depth Settings Palette
Settings optimized to reduce interference from
other sonar units
*Ping speed settings in the table are shown as a percentage of the
maximum value. Ping speed values will look different on your unit.
Selecting a shing mode:
Press 1. MENU twice.
Select 2. Sonar and press ENTER.
Highlight 3. Fishing Mode and press ENTER.
Select the desired shing mode and press 4. ENTER.
Sonar display settings/options
To adjust Sensitivity and Colorline:
From the Sonar page press the 1. MENU key.
Select 2. Adjust and press ENTER.
Press the keypad up/down to select Sensitivity or Colorline. Press 3.
the keypad left/right arrows to make adjustments.
To mark Underwater object with waypoint:
From the Sonar page, press the keypad to 1.
activate the cursor.
Use the keypad to center the cursor over 2.
the underwater object and press ENTER.
To select a Sonar page Palette:
From the Sonar page press the 1. MENU key. The Sonar
menu will appear.
Select 2. Sonar Options and press ENTER.
Select3. Palette and press ENTER.
Select the desired palette and press 4. ENTER.
Sonar page Split screen options
To select a Split screen display:
From the Sonar page press 1. MENU.
Select 2. Sonar options and press ENTER.
Select 3. Split to open the Split menu.
Select the desired split screen and press 4.
ENTER.
To view two Frequencies at once:
Press 1. PAGES to access the Pages screen.
From the Pages screen, select 2. Sonar +
Sonar and press ENTER.
Go To Cursor / Cancel Navigation
MMC/SD card slot
To Create Waypoint at current position:
Waypoints
Press the 1. WPT/Find key to create a waypoint at the your current
position.
To Create Waypoint at the cursor position on Chart page:
Place the cursor on the Chart 1.
page where you want to set the
waypoint and press the ENTER.
Select 2. Save from the New
Waypoint menu and press
ENTER.
To Navigate to the cursor:
From the Chart page, center the 1.
cursor over a point of interest.
Press the MENU key.
Select 2. Go to Cursor and press
ENTER.
To cancel navigation:
From the Chart menu select 1. Navigation and press ENTER.
Select 2. Cancel and press ENTER.
The MMC/SD card slot allows you to view
mapping charts and save/view route, trail and
sonar log data.
Make sure the MMC card slot door is always
closed to help prevent moisture from getting
into the card slot compartment. To prevent
damage to the card slots, use care when inserting cards in the card slots.
*988-10064-001*
Loading...