Lorex LH150 ECO4, LH158 ECO4, LH156 ECO4 Instruction Manual

Page 1
Instruction Manual
LH150 ECO4 SERIES
Page 2
Page 3
Instruction Manual
LH150 ECO4 SERIES
#LX400012; r. 2.0/12066/12066; en-US
iii
Page 4
Thank you for purchasing this product. Lorex is committed to providing our customers with a high quality, reliable security solution.
This manual refers to the following models:
LH156 (16-channel)
For the latest online manual, downloads and product updates, and to learn about our complete line of accessory products, please visit our website at:
www.lorextechnology.com
WARNING
RISK OF ELECTRIC SHOCK DO NOT OPEN
WARNING: TO REDUCE THE RICK OF ELECTRIC SHOCK DO NOT REMOVE COVER. NO USER SERVICABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF THE PLUG TO THE WIDE SLOT AND FULLY INSERT.
#LX400012; r. 2.0/12066/12066; en-US
iv
Page 5
Table of contents
1 Important Safeguards ........... ............ ............ ....... ........................ ........1
1.1 General Precautions ....... ............ ............ ............ ................... ..... .1
1.2 Installation........... ............ ............ ........................ ....... ............ ...1
1.3 Service ........................ ............ ............ ............ ....... ............ ......3
1.4 Use....... ................... ............ ............ ............ ....... ..................... 3
2 LH150 Series Features .... ................... ............ ............ ............ ....... ....... 4
3 Getting Started (LH150 Series). ............ ............ ................... ............ ......5
4 Front Panel (LH150 Series) ........... ....... ..... ................... ............ ............ .6
5 Rear Panel (LH150 Series) ..................... ....... ............ ............ ............ ....9
6 Basic Setup (LH150 Series) ....... ............ ................... ............ ............ .. 11
6.1 Step 1: Connect the BNC Cameras... ............ ............ ............ ....... . 11
6.2 Step 2: Connect the Mouse..... ............ ............ ............ ................ 11
6.3 Step 3: Connect the Ethernet Cable .. ........................ ....... ............ . 11
6.4 Step 4: Connect the Monitor..... ............ ............ ............ ....... ........ 11
6.5 Step 5: Connect the Power Adapter and Power on the DVR........ ........ 12
6.6 Step 6: Upgrade Firmware to Latest Version (if Available) ......... ....... .. 12
6.7 Step 7: Verify Camera Image .... ............ ............ ................... ........ 13
6.8 Step 8: Set the Time .. ............ ............ ....... ........................ ......... 13
6.9 Default System Password & Port Numbers .. ................... ............ .... 13
6.9.1 Lorex Stratus Connectivity........ ........................ ....... ......... 13
6.10 Quick Access to System Information . ....... ........................ ............ . 14
6.11 Connecting Cameras .. ............ ............ ............ ................... ........ 14
6.11.1 Installing Cameras... ............ ............ ................... ............ 14
6.11.2 Connecting BNC Cameras to your DVR ......... ............ ......... 15
6.11.3 Connecting and Removing BNC Cables ....... ............ ........... 16
7 Mouse Control ...... ............ ............ ................... ............ ............ ......... 17
8 Remote Control ........... ............ ............ ............ ................... ..... ....... ... 18
8.1 8–Channel Remote Control ......... ............ ....... ..... ................... ..... 18
8.2 16–Channel Remote Control ...... ............ ........................ ....... ...... 19
9 Using the On-Screen Display .. ................... ............ ............ ............ ..... 21
9.1 Using the Menu Bar............... ....... ............ ............ ............ ......... 21
9.2 Using the Virtual Keyboard and Mini-Keyboard.......... ..... ....... .......... 22
9.3 Using the Zoom Mode........... ............ ............ ....... ..... ................. 23
9.4 Using Picture in Picture (PIP) Mode ............. ............ ............ ......... 23
10 Setting the Date and Time.... ............ ............ ............ ............ ....... ........ 25
10.1 Configuring Daylight Savings Time (DST)..... ............ ............ .......... 25
10.2 Using a NTP Server to set your System Time ........... ....... ............ .... 26
11 Recording.. ............ ............ ............ ........................ ....... ............ ........ 28
11.1 Recording Audio.......... ....... ..... ................... ............ ............ ...... 28
12 Playback ............. ............ ........................ ....... ............ ............ .......... 29
12.1 Playing Back Recorded Video ............. ............ ............ ............ .... 29
12.1.1 Using Playback Controls ...... ............ ............ ............ ....... . 30
12.1.2 Finding Events in the Playback Bar ...... ............ ............ ...... 31
12.1.3 Controlling the Time Range of the Playback Bar ............ ....... . 31
12.1.4 Using Zoom in Playback Mode . ............ ....... ..... ................. 32
13 Backup......... ............ ....... ..... ................... ............ ............ ............ ..... 34
13.1 Backing Up Video ....... ........................ ....... ............ ............ ....... 34
13.2 Using Video Clip Backup ......... ............ ............ ............ ............... 35
13.3 Viewing Backed Up Video.................. ................... ............ .......... 35
#LX400012; r. 2.0/12066/12066; en-US
v
Page 6
Table of contents
14 Managing Passwords........ ............ ............ ................... ..... ....... .......... 36
14.1 Changing Passwords... ....... ........................ ............ ............ ....... 36
14.2 Adding Users .... ............ ............ ....... ..... ................... ............ .... 37
15 Using the Main Menu .. ............ ............ ....... ..... ................... ............ .... 40
15.1 Display ........... ..... ....... ............ ............ ....... ..... ................... ..... 41
15.1.1 Configuring Custom Channel Names ....... ....... ............ ........ 41
15.1.2 Changing the Position of the Channel Name. ............ ............ 41
15.1.3 Adjusting Camera Color Settings .... ............ ................... .... 41
15.1.4 Enabling Covert Recording ..... ....... ............ ............ ........... 42
15.1.5 Configuring the Time and Recording Time Display......... ........ 42
15.1.6 Configuring Sequence Time . ........................ ............ ........ 42
15.1.7 Changing the Video-out Resolution .... ............ ............ ........ 43
15.1.8 Restoring the System’s Resolution if you see a Blank
Screen ......... ....... ............ ............ ............ ............ .........43
15.1.9 Adjusting Menu Transparency .. ............ ............ ................. 44
15.1.10 Adjusting the Video Margin... ............ ............ ............ ....... . 44
15.1.11 Adding Privacy Zones ................ ........................ ............ . 44
15.1.12 Creating a Custom Split-screen Display ....... ................... .... 45
15.2 Record ....... ............ ............ ............ ....... ........................ ......... 47
15.2.1 Configuring Pre-recording Settings.. ............ ............ ....... .... 47
15.2.2 Configuring Backup File Duration (Pack Duration) .. ....... ........ 47
15.2.3 Configuring the Recording Schedule (Continuous, Motion,
Alarm) .............. ........................ ............ ........................ 47
15.2.4 Enabling Audio Recording........ ............................... ......... 48
15.2.5 Configuring Recording Quality, Resolution, and Video
Frame Rate .... ..... ................... ............ ............ ............ ...49
15.3 Search ....... ........................ ....... ............ ............ ............ ......... 51
15.3.1 Using the Event Search ........... ........................ ....... ......... 51
15.3.2 Using the Log Search..... ............ ............ ............ ............. 52
15.4 Network................. ..... ....... ............ ............ ............ ................. 54
15.4.1 Configuring Network Type: DHCP & Static IP........... ....... ...... 54
15.4.2 Enabling Auto Port Forwarding ................ ............ ............ .. 54
15.4.3 Changing the DVR’s Client and HTTP Port... ................... ..... 54
15.4.4 Adjusting Remote Connectivity Streaming Rates.......... ......... 55
15.4.5 Setting up Email Notification ......... ............ ............ ....... ..... 56
15.4.6 Configuring DDNS settings........... ............ ............ ....... ..... 57
15.5 Alarm ...... ..... ....... ............ ............ ............ ................... ............ 58
15.5.1 Configuring Motion Detection.................... ............ ............ 58
15.5.2 Configuring Alarm Settings ............ ............ ....... ............ .... 59
15.6 Device.................. ............ ............ ............ ....... ....................... 61
15.6.1 Formatting the Hard Drive ........... ........................ ....... ...... 61
15.6.2 Configuring Overwrite ............. ..... ....... ............ ............ .... 61
15.6.3 Formatting USB Flash Drives ........... ........................ ....... .. 62
15.7 System ............ ............ ................... ............ ............ ............ .... 63
15.7.1 Changing Date Format .... ............ ............ ............ ............ 63
15.7.2 Changing Time Format ....... ............ ............ ............ ......... 63
15.7.3 Changing the System Language .. ............ ............ ............ .. 63
15.7.4 Changing Video Output - NTSC & PAL..... ............ ....... ........ 63
15.7.5 Configuring Menu Time Out and Auto Logout ......... ............ .. 63
15.7.6 Adding Users & Changing the Admin Password ........... ......... 63
15.7.7 Viewing System Information...... ........................ ....... ......... 64
#LX400012; r. 2.0/12066/12066; en-US
vi
Page 7
Table of contents
15.8 Advanced.......... ................... ............ ............ ............ ....... ........ 65
15.8.1 Configuring the "Auto Reboot" Feature........... ............ ......... 65
15.8.2 Configuring Firmware Upgrades .................. ............ .......... 65
15.8.3 Upgrading the System Firmware Using a USB Thumb
Drive........ ................... ............ ............ ............ ............ .66
15.8.4 Restoring to Factory Default Settings .... ............ ............ ...... 67
15.8.5 Restarting or Shutting Down the DVR ....... ....... ................... 68
15.8.6 Configuring System Warnings ............. ............ ............ ...... 69
15.8.7 Saving Your System Configuration to a USB Flash
Drive........ ................... ............ ............ ............ ............ .70
15.8.8 Loading a System Configuration from a USB Flash
Drive........ ................... ............ ............ ............ ............ .70
16 Connecting to Your DVR Over the Internet on PC or Mac. ............ ....... ..... 72
16.1 System Requirements...... ............ ............ ................... ..... .......... 72
16.2 Step 1 of 3: Connect your DVR to Your Router ......... ............ ............ 72
16.3 Step 2 of 3: Obtain the DVR’s Device ID... ................... ............ ....... 73
16.4 Step 3 of 3: Connect to the DVR Over the Internet...................... ...... 74
17 Using the PC/Mac Client Software .............. ....... ............ ............ .......... 76
17.1 Changing Viewing Modes .... ............ ............ ............ ....... ............ 77
17.2 Taking Screen Shots... ................... ............ ............ ............ ........ 77
17.3 Recording Video..... ............ ............ ............ ........................ ...... 77
17.4 Showing / Hiding Channels . ........................ ....... ............ ............ 78
17.5 Viewing the Bit Rate . ........................ ................... ............ .......... 78
17.6 Changing the Save Directory of Screenshots or Recorded
Video........... ............ ....... ..... ................... ............ ............ ........79
17.7 Changing the Format of Recorded Video (PC Only) ....... ............ ....... 79
17.8 Configuring PTZ Settings........... ............ ....... ........................ ...... 80
17.9 Video Playback ......... ............ ............ ............ ................... ........ 81
17.9.1 Video Playback Controls ....................... ............ ............... 83
17.10 Configuring Display Settings ............................ ............ ............ ... 84
17.11 Configuring Privacy Zone Settings ........... ............................... ...... 84
17.12 Configuring Recording Parameters ........... ............ ............ ............ 85
17.13 Configuring the Recording Schedule ...... ............ ................... ........ 85
17.14 Configuring System Recording Quality ...... ............ ............ ............ 86
17.15 Configuring Basic Network Settings ........... ............ ................... .... 87
17.16 Configuring the System Substream ....... ........................ ....... ......... 87
17.17 Configuring Email Notification Settings .. ..... ................... ............ .... 88
17.18 Configuring DDNS Settings... ............ ............ ........................ ...... 89
17.19 Configuring Motion Detection Settings ....... ....... ..... ................... ..... 90
17.20 Configuring your System to "Beep" During Motion . ............ ............ ... 91
17.21 Configuring Alarm Notifications .............. ............ ........................ .. 91
17.22 Configuring Hard Drive Recording Mode ........... ....... ..... ................. 92
17.23 Configuring PTZ Parameters . ....... ..... ................... ............ ........... 92
17.24 Configuring the System Time and Date ....... ............ ....... ............ .... 93
17.25 Changing the System’s Menu Time Out .... ............ ............ ............. 94
17.26 Configuring System User Accounts.......... ........................ ....... ...... 94
17.27 Viewing System Information .................. ............ ........................ .. 95
17.28 Configuring Firmware Upgrades ....... ............ ............ ............ ....... . 95
17.29 Manually Upgrading System Firmware......... ....... ............ ............ ... 95
17.30 Restoring Default Settings . ............ ............ ....... ........................ .. 96
17.31 Configuring Event Settings ....... ............ ............ ................... ........ 97
#LX400012; r. 2.0/12066/12066; en-US
vii
Page 8
Table of contents
17.32 Configuring Auto-Reboot ............. ..... ....... ............ ............ ........... 97
18 Mobile Apps: Accessing your DVR Using a Mobile Device ...... ............ .... 99
18.1 Supported Apps and Platforms .. ............ ............ ....... ................... 99
18.2 iPhone..................... ....... ............ ............ ............ ............ ....... . 99
18.2.1 Connecting to Your System Using Lorex Eco Stratus..... ....... .. 99
18.2.2 Lorex Eco Stratus Interface ...... ....... ........................ ....... 101
18.2.3 Taking Screenshots ........... ................... ............ ............ 102
18.2.4 Taking Manual Recordings ...... ............ ............ ............ ... 102
18.2.5 Using PTZ Controls . ............ ............ ............ ....... .......... 102
18.2.6 Using Remote Playback Mode on iPhone .... ............ .......... 103
18.2.7 Viewing Screenshots ........... ............ ............ ....... .......... 105
18.2.8 Viewing Manual Recordings ........... ....... ............ ............ . 106
18.2.9 Using Device Manager to Manage DVR’s .... ............ .......... 107
18.3 iPad ............ ............ ................... ............ ............ ............ ...... 108
18.3.1 Prerequisites:... ....... ..... ................... ............ ............ .... 108
18.3.2 Connecting to your DVR ....... ............ ................... .......... 108
18.3.3 Live View Interface ....................... ....... ............ ............ . 111
18.3.4 Taking Screenshots ........... ................... ............ ............ 111
18.3.5 Taking Manual Recordings ...... ............ ............ ............ ... 111
18.3.6 Using PTZ Controls . ............ ............ ............ ....... .......... 112
18.3.7 Using Remote Playback Mode ...... ............ ............ .......... 112
18.3.8 Viewing Screenshots ........... ............ ............ ....... .......... 114
18.3.9 Viewing Manual Recordings ........... ....... ............ ............ . 115
18.3.10 Using Device Manager to Manage DVRs ............ ............ ... 116
18.3.11 Managing Favorites .. ............ ............ ....... ..................... 117
18.4 Android ......... ....... ............ ............ ............ ........................ .... 118
18.4.1 Connecting to Your System Using Lorex Eco Stratus..... ....... 118
18.4.2 Lorex Eco Stratus Interface ...... ....... ........................ ....... 120
18.4.3 Taking Screenshots ........... ................... ............ ............ 121
18.4.4 Taking Manual Recordings ...... ............ ............ ............ ... 121
18.4.5 Using PTZ Controls . ............ ............ ............ ....... .......... 121
18.4.6 Using Remote Playback Mode on Android . ............ ............ 122
18.4.7 Viewing Screenshots ........... ............ ............ ....... .......... 124
18.4.8 Viewing Manual Recordings ........... ....... ............ ............ . 126
18.4.9 Using Device Manager to Manage DVR’s .... ............ .......... 127
19 Lorex Player 11: Playing Backed up Video on PC .. ....... ........................ 129
19.1 Running Lorex Player 11...... ............ ............ ............ ....... .......... 129
19.2 Lorex Player 11 Interface Overview ....... ..... ................... ............ .. 130
19.2.1 About the Advanced Config Menu ....... ............ ............ ..... 130
19.3 Converting Backed Up Video to AVI Files ...... ........................ ....... 131
20 Lorex Player for Mac: Viewing Backed up Video on Mac ......... ............ .. 133
20.1 Opening Individual Video Files..... ........................ ............ .......... 133
20.2 Loading Multiple Video Files. ............................... ............ .......... 133
20.3 Lorex Player for Mac Interface ................ ............ ............ ........... 134
21 Connecting a PTZ Camera (LH150 Series) ......... ............ ....... ............ .. 135
21.1 Configuring PTZ Settings........... ............ ....... ........................ .... 135
21.2 Using the PTZ Menu (Local DVR) ............ ............ ............ ........... 136
21.3 PTZ Presets and PTZ Cruise .. ............ ............ ....... ..... ............... 137
21.3.1 PTZ Preset Controls .. ............ ................... ..... ....... ........ 137
21.3.2 Setting PTZ Presets........ ................... ..... ................... ... 137
#LX400012; r. 2.0/12066/12066; en-US
viii
Page 9
Table of contents
21.3.3 Selecting PTZ Presets. ............ ....... ........................ ....... 138
21.3.4 Deleting PTZ Presets ...... ................... ..... ....... ............ ... 138
21.3.5 Starting / Stopping PTZ Cruise ........... ................... .......... 138
22 Connecting Additional External Monitors (LH150 Series) . ............ ........ 139
22.1 Connecting the DVR to TV RCA Ports ........... ............ ............ ...... 139
22.2 Customizing the Channel Arrangement on the External
Monitor .................. ............ ............ ............ ................... ........ 139
23 Recording Audio (LH150 Series) .. ........................ ............ ................. 141
24 Replacing the Hard Drive (LH150 Series).......... ....... ..... ................... ... 142
24.1 Removing the Hard Drive...... ..... ................... ............ ............ .... 142
24.1.1 8–Channel. ............ ............................... ............ .......... 142
24.1.2 16–Channel ........... ............................... ............ .......... 143
24.2 Installing the Hard Drive .. ............ ............ ............ ................... .. 145
24.2.1 8–Channel. ............ ............................... ............ .......... 145
24.2.2 16–Channel ........... ............................... ............ .......... 146
24.3 Formatting the Hard Drive ............ ............ ............ ................... .. 148
25 DDNS Setup (Advanced) ........... ............ ....... ............ ............ ............ 149
25.1 Accessing your DVR within a local network (LAN) .. ....... ................. 149
25.1.1 Step 1 of 3: Connect your DVR to the Local Area
Network...... ............ ................... ............ ............ ......... 149
25.1.2 Step 2 of 3: Obtain the DVR’s Local IP Address ................... 150
25.1.3 Step 3 of 3: Connect to the DVR’s Local IP Address .. ........... 150
25.2 DDNS Setup—Access your DVR Remotely over the Internet ........... . 152
25.2.1 Step 1 of 4: Port Forwarding .............. ....... ............ .......... 152
25.2.2 Step 2 of 4: Create a DDNS Account . ............ ............ ....... 153
25.2.3 Step 3 of 4: Enable DDNS on the DVR .. ............ ............ .... 157
25.2.4 Step 4 of 4: Connect to the DVR’s DDNS Address ......... ...... 157
26 Troubleshooting .. ............ ............ ............ ............ ....... ..................... 160
27 LH150 Series System Specifications..... ..... ....... ............ ............ ......... 163
28 Notices.............. ..... ....... ............ ............ ............ ............ ....... .......... 166
28.1 FCC/IC Notice........ ............ ............ ............ ....... ..................... 166
28.2 Modification........ ............ ............ ................... ........................ 166
28.3 ROHS .............. ....... ............ ............ ............ ............ ....... ...... 166
#LX400012; r. 2.0/12066/12066; en-US
ix
Page 10
Page 11
1
Important Safeguards
In addition to the careful attention devoted to quality standards in the manufacturing proc­ess of your product, safety is a major factor in the design of every instrument. However, safety is your responsibility too. This sheet lists important information that will help to en­sure your enjoyment and proper use of the product and accessory equipment. Please read them carefully before operating and using your product.
1.1 General Precautions
1. All warnings and instructions in this manual should be followed.
2. Remove the plug from the outlet before cleaning. Do not use liquid aerosol detergents. Use a water-dampened cloth for cleaning.
3. Do not use this product in humid or wet places.
4. Keep enough space around the product for ventilation. Slots and openings in the stor­age cabinet should not be blocked.
5. It is highly recommended to connect the product to a surge protector to protect from damage caused by electrical surges. It is also recommended to connect the product to an uninterruptible power supply (UPS), which has an internal battery that will keep the product running in the event of a power outage.
CAUTION
Maintain electrical safety. Power line operated equipment or accessories connected to this product should bear the UL listing mark or CSA certification mark on the accessory itself and should not be modi­fied so as to defeat the safety features. This will help avoid any potential hazard from electrical shock or fire. If in doubt, contact qualified service personnel.
1.2 Installation
1. Read and Follow Instructions - All the safety and operating instructions should be read before the product is operated. Follow all operating instructions.
2. Retain Instructions - The safety and operating instructions should be retained for fu­ture reference.
3. Heed Warnings - Comply with all warnings on the product and in the operating instructions.
4. Polarization - Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other.
A grounding type plug has two blades and a third grounding prong.
The wide blade or the third prong are provided for your safety.
If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
#LX400012; r. 2.0/12066/12066; en-US
1
Page 12
1
Important Safeguards
5. Power Sources - This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supplied to your location, consult your video dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.
6. Overloading - Do not overload wall outlets or extension cords as this can result in the risk of fire or electric shock. Overloaded AC outlets, extension cords, frayed power cords, damaged or cracked wire insulation, and broken plugs are dangerous. They may result in a shock or fire hazard. Periodically examine the cord, and if its appear­ance indicates damage or deteriorated insulation, have it replaced by your service technician.
7. Power-Cord Protection - Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them. Pay particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.
8. Surge Protectors - It is highly recommended that the product be connected to a surge protector. Doing so will protect the product from damage caused by power surges. Surge protectors should bear the UL listing mark or CSA certification mark.
9. Uninterruptible Power Supplies (UPS) - Because this product is designed for con­tinuous, 24/7 operation, it is recommended that you connect the product to an uninter­ruptible power supply. An uninterruptible power supply has an internal battery that will keep the product running in the event of a power outage. Uninterruptible power sup­plies should bear the UL listing mark or CSA certification mark.
10. Ventilation - Slots and openings in the case are provided for ventilation to ensure reli­able operation of the product and to protect it from overheating. These openings must not be blocked or covered. The openings should never be blocked by placing the prod­uct on a bed, sofa, rug, or other similar surface. This product should never be placed near or over a radiator or heat register. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided and the product manufacturer’s instructions have been followed.
11. Attachments - Do not use attachments unless recommended by the product manu­facturer as they may cause a hazard.
12. Water and Moisture - Do not use this product near water — for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement, near a swimming pool and the like.
13. Heat - The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.
14. Accessories - Do not place this product on an unstable cart, stand, tripod, or table. The product may fall, causing serious damage to the product. Use this product only with a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold with the product. Any mounting of the product should follow the manufacturer’s instruc­tions and use a mounting accessory recommended by the manufacturer.
15. Camera Extension Cables – Check the rating of your extension cable(s) to verify compliance with your local authority regulations prior to installation.
16. Mounting - The cameras provided with this system should be mounted only as in­structed in this guide or the instructions that came with your cameras, using the pro­vided mounting brackets.
#LX400012; r. 2.0/12066/12066; en-US
2
Page 13
1
Important Safeguards
17. Camera Installation - Cameras are not intended for submersion in water. Not all cam­eras can be installed outdoors. Check your camera environmental rating to confirm if they can be installed outdoors. When installing cameras outdoors, installation in a sheltered area is required.
1.3 Service
1. Servicing - Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
2. Conditions Requiring Service - Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:
• When the power supply cord or plug is damaged.
• If liquid has been spilled or objects have fallen into the product.
• If the product has been exposed to rain or water.
• If the product has been dropped or the cabinet has been damaged
• If the product does not operate normally by following the operating instructions. Ad-
just only those controls that are covered by the operating instructions. Improper ad­justment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation.
• When the product exhibits a distinct change in performance. This indicates a need
for service.
3. Replacement Parts - When replacement parts are required, have the service techni­cian verify that the replacements used have the same safety characteristics as the orig­inal parts. Use of replacements specified by the product manufacturer can prevent fire, electric shock, or other hazards.
4. Safety Check - Upon completion of any service or repairs to this product, ask the service technician to perform safety checks recommended by the manufacturer to de­termine that the product is in safe operating condition.
1.4 Use
1. Cleaning - Unplug the product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
2. Product and Cart Combination - When product is installed on a cart, product and cart combination should be moved with care. Quick stops, excessive force, and un­even surfaces may cause the product and cart combination to overturn.
3. Object and Liquid Entry - Never push objects of any kind into this product through openings as they may touch dangerous voltage points or “short-out” parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.
4. Lightning - For added protection of this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power line surges.
#LX400012; r. 2.0/12066/12066; en-US
3
Page 14
2
LH150 Series Features
Digital Video Recorder Features
• 960H (960x480) recording resolution, D1/2CIF/CIF supported.
• H.264 video compression
• Real time recording 30fps per channel: 8ch @960H, 16ch @480x240.
• Pentaplex operation - view, record, playback, back up & remotely control the system
simultaneously.
• 24/7 100% Duty cycle hard drive pre-installed.
• PTZ cameras supported (RS485), controllable remotely via app.
• Accurate time stamps with NTP & Daylight Savings Time.
Connectivity Features
• Lorex Stratus Connectivity - Quick & simple Internet cloud connectivity
• Instant mobile viewing on compatible smart phones & tablets
• PC and Mac compatible.
• Instant email alerts with snap shot attachment.
1
.
2
3
.
.
Note
1. Recording time may vary based on recording resolution & quality, lighting conditions and movement in the scene.
2. Requires a high speed Internet connection and a router (not included).
3. Smart Phone & Tablet Compatibility: iPad®, iPhone®, Android™. Mobile phone data plan is re­quired (not included). For the latest list of supported apps and devices, check
www.lorextechnology.com/support.
All trademarks belong to their respective owners. No claim is made to the exclusive right to use the trade­marks listed, other than the trademarks owned by Lorex Corporation. We reserve the right to change models, configurations or specifications without notice or liability. Product may not be exactly as shown. Images are simulated.
#LX400012; r. 2.0/12066/12066; en-US
4
Page 15
3
Getting Started (LH150 Series)
The system comes with the following components:
DVR (Digital Video Recorder) 12V DC Power Supply
USB Mouse Ethernet Cable HDMI Cable
Quick Start Guides
Hard drive size, number of channels, and camera configuration may vary by model. Please refer to your package for specific details. Check your package to confirm that you have re­ceived the complete system, including all components shown above.
Remote Control
(may not be exactly as shown)
#LX400012; r. 2.0/12066/12066; en-US
5
Page 16
4
1 2 3 4
5 6
Front Panel (LH150 Series)
8–Channel
1. IR Sensor: IR receiver for the remote control. LED Indicators:
PWR: Power LED.
HDD: Hard disk activity LED.
2. Menu & playback controls:
: In Playback Mode, press to rewind. Press repeatedly to increase rewind speed.
MENU/ESC: Opens the system menu. In menus, press to go back/exit menus.
3. Channel controls for full screen view:
CH1/5: Press to switch between channel 1 or channel 5 in full screen.
CH2/6: Press to switch between channel 2 or channel 6 in full screen.
CH3/7: Press to switch between channel 3 or channel 7 in full screen.
CH4/8: Press to switch between channel 4 or channel 8 in full screen.
: In Playback Mode, press to play/pause video.
• In Live Viewing Mode, press to open Search Menu to select playback time.
: In Playback Mode, press to fast forward. Press repeatedly to increase fast for-
ward speed.
: In Playback Mode, press to stop video playback.
• In Live Viewing Mode, press to stop DVR recording. Password required; does not override scheduled recording.
• Press and hold for 15 seconds to reset the DVR to the default resolution. DVR will reboot.
: Press to stop/resume recording. When the channel displays a red box with the
letter "C", the channel is recording.
: In Live Viewing Mode, press repeatedly to switch between split-screen viewing
modes.
#LX400012; r. 2.0/12066/12066; en-US
6
Page 17
4
1 2 3 4
5
6
Front Panel (LH150 Series)
4. Navigation buttons:
: Press to move cursor up.
: Press to move cursor down.
: Press to move cursor left.
: Press to move cursor right.
5. PTZ/
:
• Within system menus: Press to confirm a selection.
• In Viewing mode, press to open the System Information window.
• In Viewing mode, press and hold for 6 seconds to open the PTZ menu.
6. USB port: Connect a USB mouse (included) or USB flash drive (not included) for data backup or firmware updates.
16–Channel
1. IR Sensor: IR receiver for the remote control. LED Indicators:
PWR: Power LED.
HDD: Hard disk activity LED.
2. Menu & playback controls:
: In Playback Mode, press to rewind. Press repeatedly to increase rewind speed.
: In Playback Mode, press to play/pause video.
• In Live Viewing Mode, press to open Search Menu to select playback time.
: In Playback Mode, press to fast forward. Press repeatedly to increase fast for-
ward speed.
: In Playback Mode, press to stop video playback.
• In Live Viewing Mode, press to stop DVR recording. Password required; does not override scheduled recording.
• Press and hold for 15 seconds to reset the DVR to the default resolution. DVR will reboot.
: Press to stop/resume recording. When the channel displays a red box with the
letter "C", the channel is recording.
MENU/ESC: Opens the system menu. In menus, press to go back/exit menus.
#LX400012; r. 2.0/12066/12066; en-US
7
Page 18
4
Front Panel (LH150 Series)
3. Channel controls for full screen view:
Ch1 ~ Ch9: Press to view channel in Full-screen View.
• To access channels 10 and greater: Press 0 for channel 10 or 1+0 for channel 10, 1 +1 for channel 11, 1+2 for channel 12, etc.
: In Live Viewing Mode, press repeatedly to switch between split-screen viewing
modes.
4. Navigation buttons:
: Press to move cursor up.
: Press to move cursor down.
: Press to move cursor left.
: Press to move cursor right.
5. PTZ/
:
• Within system menus: Press to confirm a selection.
• In Viewing mode, press to open the System Information window.
• In Viewing mode, press and hold for 6 seconds to open the PTZ menu.
6. USB port: Connect a USB mouse (included) or USB flash drive (not included) for data backup or firmware updates.
#LX400012; r. 2.0/12066/12066; en-US
8
Page 19
5
0
1
0
2
0
0120401000
0
05060
7
0
1
0
2
0
0
12
0
4
01000
0
0
5
0
6
0
7
Rear Panel (LH150 Series)
8–Channel
1. Video Input: Connect BNC cameras.
2. Video Output: Outputs the DVR interface to a BNC connection. This allows you to see your mouse cursor and have full control of the system on a secondary monitor. To switch the mouse and system interface between BNC and VGA/HDMI monitors, press
0 three times on the remote control.
Note
Use a BNC to RCA adapter (not included) to connect the DVR to RCA inputs (i.e. for a TV connection).
3. Audio Input: Input for RCA audio-enabled cameras (not included).
4. VGA: Connect a VGA monitor (not included) to view the system interface.
5. RS485/Alarm Block: Connect compatible PTZ cameras (not included) or alarm sen­sor devices (not included).
6. IR EXT: Service only; not supported.
7. On/Off Switch: Turns the DVR on or off.
8. DC12V: Connect the included AC power adapter.
9. USB Port: Connect a USB mouse (included) or USB flash drive (not included) for data backup or firmware updates.
10. LAN: Connect a RJ45 Ethernet cable for local and remote connectivity.
11. HDMI: Connect to an HDMI monitor or TV (not included) to view the system interface.
12. Audio Output: Output for 1 RCA audio channel (e.g. speakers).
16–Channel
1. Video Input: Connect BNC cameras.
#LX400012; r. 2.0/12066/12066; en-US
9
Page 20
5
Rear Panel (LH150 Series)
2. Video Output: Outputs the DVR interface to a BNC connection. This allows you to see your mouse cursor and have full control of the system on a secondary monitor. To switch the mouse and system interface between BNC and VGA/HDMI monitors, press
0 three times on the remote control.
Note
Use a BNC to RCA adapter (not included) to connect the DVR to RCA inputs (i.e. for a TV connection).
3. Audio Input: Input for RCA audio-enabled cameras (not included).
4. VGA: Connect a VGA monitor (not included) to view the system interface.
5. RS485/Alarm Block: Connect compatible PTZ cameras (not included) or alarm sen­sor devices (not included).
6. IR EXT: Service only; not supported.
7. On/Off Switch: Turns the DVR on or off.
8. DC12V: Connect the included AC power adapter.
9. USB Port: Connect a USB mouse (included) or USB flash drive (not included) for data backup or firmware updates.
10. LAN: Connect a RJ45 Ethernet cable for local and remote connectivity.
11. HDMI: Connect to an HDMI monitor or TV (not included) to view the system interface.
12. Audio Output: Output for 1 RCA audio channel (e.g. speakers).
#LX400012; r. 2.0/12066/12066; en-US
10
Page 21
6
0
Basic Setup (LH150 Series)
6.1 Step 1: Connect the BNC Cameras
• Connect BNC cameras to the Video Input ports on the rear panel of the DVR.
Push and twist the BNC connector clockwise to secure it to the BNC port
6.2 Step 2: Connect the Mouse
• Connect a USB mouse (included) to one of the USB ports.
6.3 Step 3: Connect the Ethernet Cable
• Connect an Ethernet cable (included) to the LAN port on the rear panel of the DVR.
Connect the other end of the Ethernet cable to a router on your network.
6.4 Step 4: Connect the Monitor
• Connect the included HDMI cable from the HDMI port to the TV or monitor
(recommended).
OR
• Connect a VGA cable (not included) from the VGA port to the monitor.
#LX400012; r. 2.0/12066/12066; en-US
11
Page 22
6
0
1
2
0
0
Basic Setup (LH150 Series)
1. VGA port.
2. HDMI port.
6.5 Step 5: Connect the Power Adapter and Power on the DVR
1. Connect the included power adapter to the DC 12V port. Connect the end of the power adapter to a wall socket or a surge protector.
2. Turn the power switch to I to turn on the DVR.
At startup, the system performs a basic system check and runs an initial loading sequence. After a few moments, the system loads a live display view.
6.6 Step 6: Upgrade Firmware to Latest Version (if Available)
If a firmware upgrade is available, you will be asked to install it once the DVR starts up. It is required to upgrade your system firmware and client software or mobile apps to the latest version to enable remote connection to the system.
If a firmware upgrade is available:
1. After startup, a notification will appear asking you to upgrade the firmware. Click Yes to upgrade.
#LX400012; r. 2.0/12066/12066; en-US
12
Page 23
6
Basic Setup (LH150 Series)
2. Enter the system user name (default: admin) and password (default: 000000) and click Apply. Wait for the firmware update to complete. The system will restart once the firmware has been upgraded.
WARNING
DO NOT POWER OFF THE DVR OR DISCONNECT THE POWER CABLE DURING FIRMWARE INSTALLATION
6.7 Step 7: Verify Camera Image
• Power on the cameras, and then verify the camera video quality before mounting the
cameras to a permanent location.
• Mount the cameras under a sheltered location. Always verify the outdoor rating of your
camera before installing it in a permanent location.
6.8 Step 8: Set the Time
• Set the system time and date for accurate video time stamps. Videos with inaccurate
times may not be valid as surveillance evidence.
• For details on setting the system time, see 10 Setting the Date and Time, page 25.
6.9 Default System Password & Port Numbers
CAUTION
By default, the system user name is admin and the password is 000000. It is essential that you create your own password. For details, see 14 Managing Passwords, page 36.
The system requires a user name and password to log in to the system remotely using a computer or mobile device. After logging on remotely the first time, you will be asked to create a custom password for the system.
Local DVR and remote connectivity (LAN & Internet) user name and password:
• Username: admin
• Password: 000000
Default ports for DDNS remote access:
• Port 80 (HTTP port)
• Port 9000 (Client port)
6.9.1 Lorex Stratus Connectivity
This system features the exclusive Lorex Stratus Connectivity. This is a cloud service that allows you to connect to your system over the Internet via a secure handshake with Lorex’s servers. This means you can easily connect to your system without requiring any network configuration.
For details on setting up your system to connect to the Internet using Lorex Stratus Connectivity:
• See 16 Connecting to Your DVR Over the Internet on PC or Mac, page 72.
OR
• See 18 Mobile Apps: Accessing your DVR Using a Mobile Device, page 99.
Connectivity using Lorex’s free DDNS service is also available, but requires the ports listed above to be port forwarded on your router.
#LX400012; r. 2.0/12066/12066; en-US
13
Page 24
6
Basic Setup (LH150 Series)
6.10 Quick Access to System Information
To quickly open a window that displays vital system information:
• Press the
button on the front panel or remote control to open the System Informa-
tion window.
OR
• Right-click and then click the Main Menu button (
). Login using the DVR user
name and password (the default user name is admin, and the default password is
000000). Then click System>Info.
6.11 Connecting Cameras
CAUTION
Cameras differ in terms of installation or mounting instructions. Please see the documentation that came with your camera(s) for specific installation instructions.
Test the cameras before permanent installation. Plan where you will route the wiring for the camera and where you will aim the camera.
Installation Tips
• Mount the camera where the lens is away from direct and intense sunlight.
• Plan your cable wiring so that it does not interfere with power lines or telephone lines.
• Ensure that the camera wiring is not exposed or easily cut.
• Mount the camera in an area that is visible, but out of reach.
• Avoid pointing the camera at a glass window to see outside, as this may result in a poor
image caused by glare from indoor / outdoor lighting conditions.
• Adjust the camera angle so that it covers an area with high traffic.
• In "high-risk" locations, have multiple cameras point in the same area. This provides
camera redundancy if a vandal attempts to damage the camera.
6.11.1 Installing Cameras
1. Mount the camera(s) to the desired mounting surface according to the instructions that came with the camera(s). Choose a firm mounting surface.
Note
If you wish to mount cameras to drywall, it is recommended to use drywall anchors (not included).
2. Adjust the camera stand to ensure that the camera has a satisfactory view of the area you would like to monitor. Stand configuration depends on the mounting surface you have chosen (see below for suggested stand configurations).
Table Mount Wall Mount
#LX400012; r. 2.0/12066/12066; en-US
Ceiling Mount
14
Page 25
6
0
1
0
2
3
00000
00
NC
1
2
3
4
6
5
Basic Setup (LH150 Series)
There are two connection points for certain cameras. Secure the stand to the top thread for wall mounts or ceiling mounts. Secure the stand to the bottom thread for table mounts or wall mounts.
1. Top Thread (Ceiling Mount, Wall Mount).
2. Bottom Thread (Table Mount).
3. Secure to camera thread.
Note
Camera model may not be exactly as shown.
6.11.2 Connecting BNC Cameras to your DVR
1. Connect the male power connector on the BNC extension cable to the female power connector on the camera.
• Connect the BNC connector to the camera.
2. Connect the female power connector on the BNC extension cable to the power adapter.
3. Connect the BNC connector to one of the Video Input ports on the rear panel of the DVR.
4. Plug the camera power adapter to a power outlet.
Camera Installation Diagram
1. Camera.
2. End of extension cable with male power connector.
3. Extension cable.
4. End of extension cable with female power connector.
5. Camera power adapter.
6. DVR.
#LX400012; r. 2.0/12066/12066; en-US
15
Page 26
6
Basic Setup (LH150 Series)
6.11.3 Connecting and Removing BNC Cables
BNC (Bayonet Nut Connector) is a special connector that locks on to the system port and cannot be accidently removed.
To connect or remove a BNC connector:
• Push the BNC connector firmly into the BNC port and simultaneously twist the connec-
tor clockwise to tighten.
• To remove a BNC connector from a BNC port, push and simultaneously twist the con-
nector counter-clockwise to loosen the BNC connector.
#LX400012; r. 2.0/12066/12066; en-US
16
Page 27
7
2
3
Mouse Control
The DVR is designed for mouse navigation. To use a USB mouse (included), connect the mouse to a USB port on the DVR.
Use the mouse buttons to perform the following:
1. Left-Button:
• Click to select a menu option.
• During live viewing in Split-screen View, double-click on a channel to view the selected channel in
full-screen; double-click the channel again to return to Split-screen View.
2. Right-Button:
• Click to open the Menu Bar (see 9.1 Using the Menu Bar, page 21).
• In menus, use the right-button to go back / exit menus.
3. Scroll-Wheel: No function.
#LX400012; r. 2.0/12066/12066; en-US
17
Page 28
8
0
1
2
3
4
5
Remote Control
You can also control the DVR using the included remote control.
8.1 8–Channel Remote Control
1. Number keys (1~0): Press to select the desired channel in Full-screen View. Press 1 +0 for channel 10, 1+1 for channel 11, etc.
MENU: Press to open the Main Menu. In menus, press to go back/exit menus.
0: Press 0 three times to show the mouse cursor on the BNC monitor or the monitor
2. Navigation cursors: Press to navigate menus.
3. SUB MENU: Press to open the Menu Bar.
4. MUTE: Press to mute/un-mute audio during Live Viewing and Playback Mode. Audio­capable cameras (not included) are required for audio recording and listen-in audio functionality.
: In Live Viewing Mode, press to open split-screen view. Press repeatedly to
switch between split-screen viewing modes.
connected with VGA/HDMI.
: Press to select menu items. In Live Viewing Mode, press to access System
Information.
#LX400012; r. 2.0/12066/12066; en-US
18
Page 29
8
1
2
3
Remote Control
5. Playback controls:
: In Playback Mode, press to fast forward/increase fast forward speed.
: In Playback Mode, press to rewind/increase rewind speed.
: In Live Viewing Mode, press to open the Search Menu to select video for
playback.
• In Playback Mode, press to play video.
: In Live Viewing Mode, press to start Sequence Mode.
• In Playback Mode, press to pause video. Press repeatedly to step through video frames.
: Press to stop recording. Password required; does not override scheduled
recording.
: Record: Press to resume recording after recording has been stopped. Pass-
word required.
Note
When using the remote control to enter password and camera titles, select the field using the navigation
buttons, press
, and then press the number buttons.
8.2 16–Channel Remote Control
#LX400012; r. 2.0/12066/12066; en-US
19
Page 30
8
Remote Control
1. REC: Press to resume recording after recording has been stopped.
SEARCH: Press to open the Search menu.
Number keys (1-0): In Live Viewing Mode, press to open the desired channel in Full-screen view. Press 1+0 for channel 10, 1+1 for channel 11, etc.
0: Press 0 three times to show the mouse cursor on the BNC monitor or the monitor connected with HDMI/VGA.
Display Mode: In Live Viewing Mode, press repeatedly to switch through split­screen viewing modes.
2x2 / 3x3 / 4x4: In Live Viewing Mode, press to open the corresponding split­screen view. Press repeatedly to change channels shown in split-screen.
AUTO: Press to start/stop Sequence Mode.
2. Navigation cursors: Press to navigate menus.
ENTER: In menus, press to confirm selections.
• In Live Viewing Mode, press to access System Information.
3. MENU/ESC: Press to open the system menu. In menus, press to go back/exit menu.
MUTE: In Live Viewing and Playback Modes, press to mute/un-mute audio.
PIP: In Live Viewing Mode, press once to open Picture in Picture (PIP) 1X1 or twice to open PIP 1X2. Mouse is required to change channels shown in PIP.
4. Playback controls:
FWD: In Playback Mode, press to fast forward/increase fast forward speed.
REW: In Playback Mode, press to rewind/increase rewind speed.
PLAY: In Playback Mode, press to play / pause video.
• In Live Viewing Mode, press to open the Record Search Menu.
STOP: In Playback Mode, press to pause playback.
• In Live Viewing Mode, press to stop recording. Password required; does not
override scheduled recording.
SLOW: In Playback Mode, press to play video in slow motion. Press repeatedly to change slow motion playback speed.
PAUSE/FRAME: In Playback Mode, press to pause. Press repeatedly to view re- cordings frame by frame.
#LX400012; r. 2.0/12066/12066; en-US
20
Page 31
9
M
C
C C
1
2
3
1
2 3
4
5
6 7
8
9
10 11
12
Using the On-Screen Display
Use the system’s graphical on-screen display to navigate menus and configure options and settings.
1. Date & Time: Displays the date and time on the system
2. Record Status: Displays the current recording status of the system: C = continuous (normal recording); M = motion recording; A = alarm recording (only available on mod­els that have alarm/sensor support; alarm/sensor devices are required and are not included).
3. Channel Number/Channel Title: Displays channel number or channel title. To re­name the channel number to a title, see 15.1.1 Configuring Custom Channel Names, page 41.
Note If you can’t see your mouse cursor on screen:
Press 0 on the remote control three times to switch the mouse and system interface between VGA/HDMI and BNC monitors.
9.1 Using the Menu Bar
The Menu Bar allows you to access the Main Menu and control basic functions of the DVR.
To access the Menu Bar:
• Right-click or move the mouse cursor to the bottom of the screen to access the Menu
Bar.
1. Main Menu: Opens the Main Menu.
2. Lock: Click to log out if a user is currently logged in.
#LX400012; r. 2.0/12066/12066; en-US
21
Page 32
9
Using the On-Screen Display
3. Split Screen buttons: Select the desired split-screen mode (available options de­pend on the number of channels your DVR has).
4. PTZ: Opens the PTZ controls.
5. Start/Stop PTZ Cruise: Start or stop the PTZ cruise function.
6. Zoom: Opens digital zoom. Must be in Full-screen / Live Viewing Mode.
7. Record Search: Opens the DVR Search Menu. This allows you to search for video recorded on the DVR.
8. Start/Stop Recording: Start or stop DVR recording on all channels. Password re­quired; does not override scheduled recording.
9. Start/Stop SEQ: Start or stop Sequence Mode. In Sequence Mode, DVR automati­cally switches between channels every few seconds.
10. PIP 1X1: Enable Picture in Picture Mode with one camera in full screen and one in a small window.
11. PIP 1X2: Enable Picture in Picture Mode with one camera in full screen and two in small windows.
12. Volume: Adjust the DVR volume (audio-capable cameras required, not included).
9.2 Using the Virtual Keyboard and Mini-Keyboard
You can input numeric or text values using the on-screen virtual keyboard. You will need to use the Virtual Keyboard when entering your User ID and Password. The Virtual Mini-Key­board is used to input numeric values, such as the time and date.
To use the Virtual Keyboard:
1. Using the mouse, click on an option or field, such as the User ID and Password fields.
• The Virtual Keyboard opens.
• Click Shift to switch between upper and lowercase letters.
• Click
to move the cursor between letters.
• Click <— to backspace/delete.
• Click Enter to enter your selection.
• Click ESC to close the virtual keyboard.
#LX400012; r. 2.0/12066/12066; en-US
22
Page 33
9
000
0
1
2
Using the On-Screen Display
To use the Virtual Mini-Keyboard:
1. Using the Mouse, click on an option or field, such as the Time or Date fields.
• The Virtual Mini-Keyboard opens.
• Click to enter your selection.
9.3 Using the Zoom Mode
Zoom Mode allows you to zoom in on an image while viewing your cameras live. This can be useful if you want to get a closer look at a situation.
To use the Zoom Mode:
1. In Live Viewing Mode, select the channel you want to zoom in on in full-screen (dou­ble-click the channel if you are in a Split-screen View).
2. Right-click to open the Menu Bar and select the Zoom button (
). A Zoom icon ap-
pears on the screen.
2.1. Click and drag on the area of the screen you would like to enlarge. The image zooms in on the
selected area.
2.2. The box in the lower right-hand corner shows the entire camera picture with a black box around
the zoomed-in area. Click inside the box and drag to move the zoom area.
3. Right-click to exit and select a different zoom area. Right-click again to exit Zoom Mode and return to Live Viewing Mode.
9.4 Using Picture in Picture (PIP) Mode
Picture in Picture (PIP) Mode allows you to view one channel in full-screen while viewing up to two other channels.
To use Picture in Picture Mode:
1. Right-click to open the Menu Bar and select the PIP1X1 button (
(
). PIP1X1 shows one channel in full screen and one other channel; PIP1X2 shows
one channel in full screen and two other channels.
#LX400012; r. 2.0/12066/12066; en-US
) or PIP1X2 button
23
Page 34
9
1
2
3
Using the On-Screen Display
2. Picture in Picture Mode opens.
2.1. To change the full-screen channel, click anywhere in the main viewing area.
2.2. To move the smaller channels around the screen, click inside the white bar and
drag.
2.3. To change the smaller channels, click inside the channel.
2.4. Right-click to exit and return to Live Viewing Mode.
#LX400012; r. 2.0/12066/12066; en-US
24
Page 35
10
0
Setting the Date and Time
CAUTION
It is highly recommended to set the date and time when first setting up your system.
Inaccurate time stamps may render your footage unusable for court evidence.
1. Right-click or move your mouse to the bottom of the screen to open the Menu Bar and
click the Main Menu button (
2. Enter the system user name (default: admin) and password (default: 000000) and click Apply.
3. Click System.
4. Configure the following:
Date: Click inside the field and enter the month, date, and year.
Time: Click inside the field and enter the time.
(Optional) Date Format: Use the drop-down menu to select MM/DD/YY, DD/MM/
YY, or YY-MM-DD.
(Optional) Time Format: Use the drop-down menu to select 12HOURS or
24HOURS.
(Optional) DST: Click the Setup button next to DST to configure automatic Daylight
Savings Time adjustments.
(Optional) NTP: Click the Setup button next to NTP to synchronize your DVR’s
time and date with a Network Time Protocol (NTP) time server. Lorex provides a free NTP service that automatically updates your DVR’s time for Daylight Savings Time.
).
Note
A constant internet connection is required for the NTP server feature to function.
5. Click Apply to save your settings.
10.1 Configuring Daylight Savings Time (DST)
If your region observes Daylight Savings Time (DST), follow the instructions below to con­figure your DVR to automatically update the time when the clock updates.
#LX400012; r. 2.0/12066/12066; en-US
25
Page 36
10
Setting the Date and Time
To enable automatic DST adjustments:
1. Click the DST Setup button.
2. Configure the following:
Daylight Saving Time: Select Enable.
Time Offset: Select the number of hours the system should move forward or backward when DST
occurs.
Daylight Saving Time Mode: Select Week or Date. This allows you to select whether DST should
begin and end at the beginning of the week or on a specific date.
Start Time, End Time: Enter when DST starts and ends.
3. Click Apply to save your settings.
10.2 Using a NTP Server to set your System Time
A NTP (Network Time Protocol) server syncs your system time with an online time server. Lorex provides a free NTP service that allows your DVR to automatically update the time for Daylight Savings Time.
Note
A constant Internet connection is required to use the NTP feature.
To enable NTP:
1. Right-click to open the Menu Bar and click the Main Menu button (
).
#LX400012; r. 2.0/12066/12066; en-US
26
Page 37
10
Setting the Date and Time
2. Click System. Beside NTP, click Setup.
3. Configure the following:
Enable: Select Enable.
Server Address: Select ntp.lorexddns.net(recommended) as the time server or
select another time server.
Time Zone: Select your region’s time zone.
4. Click Update Now to connect to the time server.
5. Click Apply to save your settings.
#LX400012; r. 2.0/12066/12066; en-US
27
Page 38
11
C
M
Recording
By default, the system is set to immediately record video from connected cameras in Con­tinuous Recording Mode.
Recording—Continuous: Normal, continuous recording.
You can set the system to stop recording once the hard drive is full, or to continually record by overwriting previously recorded data. For more details, see 15.6.1 Formatting the Hard Drive, page 61.
The system also includes motion recording:
Recording—Motion: The system records when motion is detected by the camera.
11.1 Recording Audio
The system can also record audio (check your model’s specifications for the supported number of audio channels). You must have audio-capable cameras (not included) or self­powered microphones (not included) in order to record audio on the system.
For details, see 23 Recording Audio (LH150 Series), page 141.
#LX400012; r. 2.0/12066/12066; en-US
28
Page 39
12
1
2
3
Playback
You can view and back up recorded video on the system through the Search Menu.
12.1 Playing Back Recorded Video
To playback a specific date and time:
1. Right-click to open the Menu Bar and click the Record Search button (
2. Enter the system user name (default: admin) and password (default: 000000) and click Apply. The Record Search tab opens.
3. Configure the following:
3.1. CH: Select the channel you wish to search. Select All to search all channels.
3.2. Search Date: Enter the month, date, and year you wish to search for video.
3.3. Playback Time: Enter the desired time you wish to search for video.
4. Click Play to select the exact time specified in Playback Time.
5. Select the channel or channels you want to play back and click Play.
).
To search for recorded footage on the DVR:
1. Right-click to open the Menu Bar and click the Record Search button ( cord Search tab opens.
2. Configure the following:
CH: Select the channel you wish to search. Select All to search all channels.
Search Date: Enter the month, date, and year you wish to search for video.
#LX400012; r. 2.0/12066/12066; en-US
). The Re-
29
Page 40
Playback12
1
2
3. Click the Search button. Your search results appear in the calendar. In the top portion of the calendar, results are shown for each day in the month. In the bottom portion, re­sults are shown for each hour in the selected day.
3.1. Click on a date in the calendar to see the video available for that date.
3.2. Click on the hour of the video you want to play back.
4. Select the channel or channels you want to play back.
5. Click Play to begin playback.
12.1.1 Using Playback Controls
This system features advanced playback controls that allow you to see when you have re­corded footage and motion events on your cameras. They also allow you to use digital zoom in playback mode or take backups from short video clips.
Different playback controls appear depending on the number of cameras you have se­lected to playback. All available controls appear when you playback from a single camera.
To use the advanced playback controls:
• Move the mouse slightly to display the on-screen playback controls. You can also use
the playback control buttons on the remote control. Click the playback controls to play, pause, fast forward, rewind, and slow down playback.
Click X or right-click to quit playback and return to the Search Menu.
#LX400012; r. 2.0/12066/12066; en-US
30
Page 41
Playback12
3
2
4 5
6
7 8 9
10
11 12
13
14
1
Playback Controls
1. Playback Bar: Continuous recordings are shown in green. Motion or alarm recording is shown in red.
2. Start Time: Shows the start time of footage currently in the Playback Bar.
3. Rewind.
4. Slow.
5. Play.
6. Pause.
7. Fast Forward.
8. Zoom.
9. Video Clip Backup.
10. Mute.
11. Exit Playback.
12. End Time: Shows the end time of footage currently in the Playback Bar.
13. Show Playback Time Controls.
14. Change Time Range: Click one of the options to select the range of times shown in the Playback Bar.
12.1.2 Finding Events in the Playback Bar
The advanced playback controls show the time and type of video footage available. Con­tinuous recordings are shown in green and motion or alarm recordings are in red.
Note
Motion detection or alarms must be enabled for each channel before they will be highlighted, see 15.5 Alarm, page 58 for details.
When up to four channels are selected for playback, multiple channels are shown.
If more than four channels are selected, one bar is shown that combines all the selected channels. This means that video available on any selected channel will be shown in the bar.
12.1.3 Controlling the Time Range of the Playback Bar
The time range is the start and end times of the footage displayed in the Playback Bar. By default, the Playback Bar displays recordings recorded on the day selected for playback (from 00:00~24:00). You can change the time range to narrow in on a specific time.
#LX400012; r. 2.0/12066/12066; en-US
31
Page 42
Playback12
To control the time range of the Playback Bar:
1. During Playback mode, click
to open the time range controls.
2. Click 30m, 1H, 2H, or 24H to select a time range. For example, if 30m is selected, the playback bar will show 15 minutes before to 15 minutes after the currently playing time.
OR
To create a custom time range:
2.1. Click
. The button will become colored.
2.2. Move your mouse to the time you where you would like the range to start and
click. Then, move your mouse to the time you where you would like the range to end and click. The start and end times will be replaced by the 1st and 2nd times that you clicked on.
12.1.4 Using Zoom in Playback Mode
You can use Zoom in Playback Mode. This is useful if you need a closer look at recorded video.
Note
Zoom is only available when a single channel is selected for playback.
To use zoom in Playback Mode:
1. Open Playback Mode with only one channel selected. For details, see 12.1 Playing Back Recorded Video, page 29.
#LX400012; r. 2.0/12066/12066; en-US
32
Page 43
Playback12
000
0
1
2
2. Click to open Zoom.
Note
Playback controls are not available when Zoom is activated. If you want to pause the video before you zoom, you will have to pause it before entering Zoom.
2.1. Click and drag on the area of the screen you would like to enlarge. The image zooms in on the
selected area.
2.2. The box in the lower right-hand corner shows the entire camera picture with a black box around
the zoomed-in area. Click inside the box and drag to move the zoom area.
3. Right-click to exit and select a different zoom area. Right-click again to exit Zoom Mode and return to Playback Mode.
#LX400012; r. 2.0/12066/12066; en-US
33
Page 44
13
1
2
3
Backup
13.1 Backing Up Video
You can back up video to a USB flash drive (not included) connected to the DVR.
To back up video:
1. Connect a USB flash drive to one of the USB ports on the DVR.
2. Right-click to open the Menu Bar and click the Record Search button (
3. Enter the system user name (default: admin) and password (default: 000000) and click Apply.
4. Click the Backup tab.
5. Configure the following:
Search Date: Enter the desired month, date, and year.
Search Time: Enter the time range you wish to search.
CH: Select the channel you wish to search. To search all channels, select All.
Type: Select the type of recording you wish to search. Choose from All, Continu-
ous, or Alarm.
6. Click Search. A list of videos populate in the window.
).
6.1. Click the BAK checkbox beside videos you wish to back up.
6.2. Click
6.3. Click Backup to begin backing up the selected files.
7. Wait for the backup to finish before removing the USB memory drive.
#LX400012; r. 2.0/12066/12066; en-US
34
Page 45
Backup13
13.2 Using Video Clip Backup
Video clip backup allows you to select a duration of video during playback mode and save it to a USB flash drive (not included).
Note
Video clip backup is only available when a single channel is selected for playback.
To create a backup video clip:
1. Connect a USB flash drive (not included) to one of the USB ports on the DVR.
2. Open Playback Mode with only one channel selected. For details, see 12.1 Playing Back Recorded Video, page 29.
3. Click the clip backup button (
Click to select the start and stop times.
) to start your backup at the current playback time.
4. When you want the backup clip to stop, click again.
Note
You can use fast forward or click-and-drag the video cursor to select the stop time for the clip. This is useful because it allows you to backup longer segments of video without having to watch the whole video each time. You must have enough space on your USB flash drive to save the file.
5. A confirmation window appears, showing information about the backup file you are about to create. Click Backup to confirm. Wait for the file to be saved.
13.3 Viewing Backed Up Video
To view the downloaded video, you must install the Lorex Player software.
• For PC instructions, see 19 Lorex Player 11: Playing Backed up Video on PC, page 129.
• For Mac instructions, see 20 Lorex Player for Mac: Viewing Backed up Video on Mac,
page 133.
#LX400012; r. 2.0/12066/12066; en-US
35
Page 46
14
1
2
Managing Passwords
Note
By default, the system user name is admin and the password is 000000. Passwords are enabled by de­fault and are required to access the Main Menu.
The password is required to log into the system remotely using a computer or mobile device. You will be prompted to create a custom password after you connect for the first time.
The system supports the following account types:
admin—system administrator: has full control of the system, and can change both
administrator and user passwords and enable/disable password protection.
user—normal user: only has access to live viewing, search, playback, and other func-
tions. You may set up multiple user accounts with varying levels of access to the system.
For security reasons, it is essential that you change the password on your system. By de-
fault, the system password is enabled.
14.1 Changing Passwords
You can change the system password of the admin and user accounts from the Users menu.
To change the admin password:
1. Right-click to open the Menu Bar and click the Main Menu button ( system user name (default: admin) and password (default: 000000) and click Apply.
2. Click System and select the Users tab.
2.1. Select the checkbox beside admin.
2.2. Click the Edit button.
). Enter the
#LX400012; r. 2.0/12066/12066; en-US
36
Page 47
Managing Passwords14
3. Configure the following:
User Name: Enter the desired admin user name.
Password: Enter your desired password.
Confirm: Re-enter the password.
4. Click Apply to save your settings.
14.2 Adding Users
You can allow multiple users to log in to the system. When adding different users, you can assign what menus they have access to. For example, you may want your friend to monitor your system while you are away, while not giving full access to your system.
To add a new user:
1. Right-click to open the Menu Bar and click the Main Menu button (
).
#LX400012; r. 2.0/12066/12066; en-US
37
Page 48
Managing Passwords14
1
2
1
2
2. Click System> Users.
2.1. Select the checkbox beside user1 (or any other user account).
2.2. click the Permission button.
3. Select the menus and channels the user will have access to:
3.1. Select the menus the user account will be able to access.
3.2. Select the channels the user account will be able to access for each function. For example, if
channel 1 is selected for Live, the user account will be able to view live video on channel 1.
4. Click Apply to save your settings.
#LX400012; r. 2.0/12066/12066; en-US
38
Page 49
Managing Passwords14
5. Configure the following:
User Name: Enter the desired user name.
User Enable: Select Enable to enable the user account.
Password: Enter your desired password.
Confirm: Re-enter the password.
6. Click Apply to save your settings.
Now, you can log in to the system locally, or remotely using the user name and password you created. When logging into the system with a user account, the user will only have ac­cess to the menus you assigned.
#LX400012; r. 2.0/12066/12066; en-US
39
Page 50
15
Using the Main Menu
To open the Main Menu:
1. Right-click to open the Menu Bar and click the Main Menu button (
2. Enter the system user name (default: admin) and password (default: 000000) and click Apply.
).
Display: Configure display options (e.g. camera color settings, camera title, video
output).
Search: Search for recorded video and log files on the system.
Alarm: Configure motion detection and external alarm device settings.
System: Configure system time and user accounts.
Record: Configure recording settings and recording schedules.
Network: Configure system network settings (e.g. email alert settings, video streaming
quality settings).
Device: Configure PTZ settings, HDD recording mode, HDD format option.
Advanced: Configure system restart schedule, perform firmware upgrades, or config-
ure automatic upgrades.
#LX400012; r. 2.0/12066/12066; en-US
40
Page 51
Using the Main Menu15
15.1 Display
The display menu allows you to configure camera image settings and video output
settings.
Note If you want to apply settings to all channels, use the "Copy To" drop-down menu, and select All. Click the
Copy button to copy the setting across all channels.
15.1.1 Configuring Custom Channel Names
1. Select the Live tab.
2. In the Channel drop-down menu, select the channel that you wish to rename.
3. Click the Name field. Use the Virtual Keyboard to enter in the new channel name.
4. Click Apply to save your settings.
15.1.2 Changing the Position of the Channel Name
1. Select the Live tab.
2. In the Channel drop-down menu, select the channel you would like to configure.
3. In the Position drop-down menu, select where you would like the channel names to appear:
U-L: Upper left hand corner.
D-L: Lower left hand corner.
U-R: Upper right hand corner.
D-R: Lower right hand corner.
Disable: Do not display the channel name.
4. (Optional) Use the drop-downs next to Copy to copy settings to another channel or all channels. Click the Copy button to copy settings.
5. Click Apply to save your settings.
15.1.3 Adjusting Camera Color Settings
1. Select the Live tab.
2. In the Channel drop-down menu, select the channel that you wish to configure.
#LX400012; r. 2.0/12066/12066; en-US
41
Page 52
Using the Main Menu15
3. Click the Setup button next to Color. The Color Setup window opens.
4. Drag the slider to adjust the Hue, Brightness, Contrast, and Saturation.
5. Click Apply to save your settings.
15.1.4 Enabling Covert Recording
Covert Recording blanks out the screen so that it seems as if the system is not recording. Covert channels are only visible when the admin account logs in using a remote computer or mobile device.
To enable covert recording:
1. Select the Live tab.
2. In the Channel drop-down menu, select the channel you wish to hide.
3. In the Covert drop-down menu, select Enable.
4. Click Apply to save your settings.
15.1.5 Configuring the Time and Recording Time Display
To add/remove the time stamp in the system display:
1. In the Show Time and Record Time drop-down menu, select enable or disable.
2. Click Apply to save your settings.
15.1.6 Configuring Sequence Time
Sequence time refers to the amount of time a channel appears on the screen before changing to a different channel when the DVR is in Sequence Mode. For example, when Sequence Mode is on, channel 1 is shown for several seconds before switching to chan­nel 2.
#LX400012; r. 2.0/12066/12066; en-US
42
Page 53
Using the Main Menu15
To configure the sequence time:
1. Click the Output tab.
2. Click the SEQ Dwell time field and enter the time channels remain on-screen before changing to another channel.
3. Click Apply to save your settings.
15.1.7 Changing the Video-out Resolution
1. Click the Output tab.
2. Click the drop-down menu beside VGA/HDMI Resolution and select the output resolution.
3. Click Apply to save your settings.
4. Right-click repeatedly to exit all menus. The DVR prompts you to restart. Click OK.
5. The DVR restarts and asks you to confirm the new resolution. Click Yes to confirm or No to revert to the old resolution. If you do nothing, the DVR will revert to the last se­lected resolution and restart.
Note
If you select a resolution that is greater than what your monitor supports, you may see a blank screen when your DVR restarts. If this occurs, do not do anything and wait until the DVR restarts.
If this does not correct the issue, press and hold the Stop ( until the DVR restarts. Your system resolution will default to 1024 x 768.
) button on the front panel of the DVR
15.1.8 Restoring the System’s Resolution if you see a Blank Screen
If you see a blank screen on your monitor after turning on your system, the DVR’s output resolution may be higher than what your monitor supports. Follow the steps below to re­store the DVR’s default resolution to 1024 x 768.
To restore the DVR’s default resolution:
1. Ensure the power and video cables are properly connected.
#LX400012; r. 2.0/12066/12066; en-US
43
Page 54
Using the Main Menu15
2. Press and hold the Stop ( ) button on the front panel until the DVR restarts. The res-
olution will be reset to 1024 x 768 and the DVR will restart. When the DVR restarts, click Yes to confirm the default resolution.
Note
If your system resolution is already in 1024 x 768, pressing and holding the Stop button will not re­start the system.
15.1.9 Adjusting Menu Transparency
You can increase or decrease the transparency of the on-screen menus.
To adjust the transparency of on-screen menus:
1. Click the Output tab.
2. Drag the Transparency slider to adjust transparency.
3. Click Apply to save your settings.
15.1.10 Adjusting the Video Margin
If you connect your DVR to a BNC monitor, you can adjust the video margins.
Note
You must select the BNC output mode to adjust the margins. Press 0 three times on the remote control to switch the output mode between BNC mode and VGA/HDMI mode. When BNC mode is selected, the mouse cursor appears on the BNC monitor.
To adjust the video margin:
1. Click the Output tab.
2. Click the Margin button.
3. Drag the sliders to the left or right to adjust the Left, Right, Top, or Bottom Margin.
4. Click Apply to save your settings and click OK to confirm.
15.1.11 Adding Privacy Zones
A privacy zone allows you to block out up to 4 portions of each channel with a black square.
CAUTION
Areas covered by privacy zones are not visible in recordings.
To configure a privacy zone:
1. Click the Privacy Zone tab.
#LX400012; r. 2.0/12066/12066; en-US
44
Page 55
Using the Main Menu15
2. In the Channel drop-down menu, select the channel you wish to configure.
3. Configure the following:
Channel: Select the channel you wish to configure.
Privacy Zone: Select ON to enable privacy zones or OFF to disable privacy zones.
Area Setup: Select the Area1~4 checkboxes to enable up to 4 privacy zones.
4. Click the Setup button next to Mask Area. The Privacy Area setup screen opens.
• Click on a privacy area and drag to change its location.
• Click on the edge of a privacy area and drag to resize a privacy area.
• Right-click when you are finished to exit.
5. (Optional) Use the drop-downs next to Copy to copy privacy areas to another channel or all channels. Click the Copy button to copy privacy areas.
6. Click Apply to save your settings.
15.1.12 Creating a Custom Split-screen Display
You can create a custom split-screen display and re-arrange where channels are placed.
#LX400012; r. 2.0/12066/12066; en-US
45
Page 56
Using the Main Menu15
1
2 3
Note
You can create a custom split-screen display on a secondary monitor connected to the Video Output port (BNC) by doing the following.
• First, move the mouse and system interface to the Video Out monitor by pressing 0 three times on the remote control.
• Complete the procedure below.
• Press 0 three times on the remote control again to return the mouse and system interface to the VGA or HDMI monitor. Your custom display will be saved on the secondary monitor.
To re-arrange the split-screen display:
1. Select the Output tab.
1.1. Under View Setup, select Enable. This lets you select and arrange the chan­nels you want to show on the screen.
Note
Enabling View Setup disables your ability to change channels the normal way on the se­lected monitor. You will need to disable View Setup to return to normal operation.
1.2. Under View Mode, select the desired viewing mode: Single, Quad, Nine, Six-
teen, or Twentyfive.
Note
The options available depend on the number of channels your DVR has.
1.3. Click Vout Setup. A menu appears that allows you to select the arrangement of channels. Click the drop-down menus to select which channels to show on the screen and the arrangement of channels.
2. Click Apply to save changes. Click Ok. Right-click repeatedly to exit all menus and re­turn to live viewing.
#LX400012; r. 2.0/12066/12066; en-US
46
Page 57
Using the Main Menu15
15.2 Record
The Record menu allows you to configure recording settings, such as the recording resolu­tion, recording schedule, and audio recording.
15.2.1 Configuring Pre-recording Settings
1. Select the Rec Para tab.
2. In the Channel drop-down menu, select the desired channel you wish to configure.
3. In the PreRecord drop-down menu, select Enable to enable pre-recording or Disable to disable pre-recording.
4. Click Apply to save your settings.
15.2.2 Configuring Backup File Duration (Pack Duration)
Pack Duration refers to the duration of a backed up file in the system. By default, a record­ing is packaged into 15 minute video files.
To change the DVR’s backed up file size:
1. Select the Rec Para tab.
2. In the Pack Duration drop-down menu, select the desired duration (15~60 minutes).
3. Click Apply to save your settings.
Changing the file size changes the duration of backed up files. For example, if you select 15 minutes as your file size, the system stores video files in 15 minute durations.
15.2.3 Configuring the Recording Schedule (Continuous, Motion, Alarm)
To configure the recording schedule:
1. Click the Schedule tab.
2. Configure the following:
Channel: Select the channel you wish to configure the schedule for.
Week: Select the day of the week you wish to configure.
#LX400012; r. 2.0/12066/12066; en-US
47
Page 58
Using the Main Menu15
3. Click inside the grid to configure the recording schedule:
• The recording schedule is arranged as a grid. Each row represents a recording type
(Continuous, Motion, and Alarm), and each box represents an hour.
• Recording for each recording type is enabled during the selected hour when the
box is filled in with the corresponding color. Recording for each recording type is disabled for the selected hour when the box is gray.
Note
Sensor devices (not included) must be connected to the system to use Alarm recording.
4. (Optional): Use the top Copy and Copy To drop-down to copy the recording schedule to a specific day or all days. Click Copy to copy the schedule.
5. (Optional): Use the bottom Copy and Copy To drop-down to copy the recording schedule to a specific channel or all channels. Click Copy to copy the schedule.
6. Click Apply to save your settings.
15.2.4 Enabling Audio Recording
Audio-capable cameras are required (not included) for audio recording.
To enable audio recording:
1. Click the MainStream tab.
#LX400012; r. 2.0/12066/12066; en-US
48
Page 59
Using the Main Menu15
2. Beside the corresponding channel, select or deselect the checkbox under Audio to enable or disable audio recording.
3. Click Apply to save your settings.
15.2.5 Configuring Recording Quality, Resolution, and Video Frame Rate
You can configure the recording quality, recording resolution and video frame rate for each channel.
To change the recording quality, recording resolution, and video frame rate:
1. Click the MainStream tab.
2. Under Mode, select D1 or 960H. 960H will enable larger, wide-screen formats, but it will decrease the number of Frames Per Second available for recording on 8/16-chan­nel models.
Note
If you change this setting, the DVR will restart when you save changes.
3. Under the Quality drop-down menu, select from Good, Better, or Best to adjust the quality of recordings on each channel.
#LX400012; r. 2.0/12066/12066; en-US
49
Page 60
Using the Main Menu15
4. Under the Resolution drop-down menu, select the Recording Resolution for each channel:
• If D1 is selected, available options are CIF (320x240), HD1 (720x240), or D1
(720x480).
• If 960H mode is selected, available options are 480x240, 960x240, or 960x480.
5. Under the FPS drop-down menu, select the number of frames per second you want the DVR to record on each channel.
6. (Optional) Use the Copy and Copy To drop-down menus to copy recording settings to one or all channels. Click Copy to copy recording settings.
7. Click Apply to save your settings.
Note
Increasing the resolution or quality settings may decrease the amount of Frames per Second (FPS) the DVR can record, depending on the specifications of your DVR model. If you receive an error message when saving your changes, reduce the Resolution, Quality, or FPS and try again.
#LX400012; r. 2.0/12066/12066; en-US
50
Page 61
Using the Main Menu15
15.3 Search
The Search menu allows you to search for recorded video and system logs.
• For details on playing back video, see 12 Playback, page 29.
• For details on backing up video, see 13 Backup, page 34.
15.3.1 Using the Event Search
Event Search allows you to find videos that are marked as "Alarm" or "Continuous" record­ing type. This allows you to quickly and easily sort though videos that only have alarm attributes.
Note
Videos are not marked as Alarm unless continuous recording is turned off and motion or alarm settings are enabled.
To perform an Event Search:
1. Click the Event Search tab.
2. Configure the following:
Search Date: Enter the month, date, and year.
CH: Select the channels you wish to search.
Search Time: Enter the time range you wish to search.
Type: Select the recording type you wish to search for.
#LX400012; r. 2.0/12066/12066; en-US
51
Page 62
Using the Main Menu15
3. Click Search. A list populates with videos.
4. Perform one of the following:
Play video: Double-click on the desired file.
Back up a file: Connect a blank USB flash drive to your system. Select the BAK
checkbox beside the desired file name. Then, click the Backup button.
15.3.2 Using the Log Search
A log search allows you to search system event logs.
To perform a Log search:
1. Click the Log tab.
2. Configure the following to perform a Log search:
Log Type: Select the log type you wish to search under. Choose from Alarm (i.e.
motion events), Operation (i.e. Configuration changes, Setup), or All.
Start Time: Enter the time you wish to begin searching.
End Time: Enter the time you wish to end searching.
3. Click Search.
#LX400012; r. 2.0/12066/12066; en-US
52
Page 63
Using the Main Menu15
4. (Optional) Click the Backup button to backup system logs to a USB flash drive (not included).
#LX400012; r. 2.0/12066/12066; en-US
53
Page 64
Using the Main Menu15
15.4 Network
The Network menu allows you to configure network settings and email alerts.
15.4.1 Configuring Network Type: DHCP & Static IP
The system has the ability to operate in DHCP mode and Static IP mode.
To configure DHCP and Static IP settings:
1. Select the Network tab.
2. In the Type drop-down menu, select DHCP or Static. If you select DHCP, the router automatically assigns an IP to your DVR.
If you select Static, click the field beside IP Address, and enter in the IP address of your choice.
• Enter your custom Subnet Mask, Gateway, DNS1 and DNS2 using the mouse.
• You must assign the IP in your router that you wish to make static. For example, if
you assign 192.168.2.89 as the static IP in the DVR, you must assign 192.168.2.89 in your router as a static IP as well. Consult your router’s user’s manual for details.
3. Click Apply to save your settings.
4. Right-click until you exit all menus. You will be prompted to restart.
15.4.2 Enabling Auto Port Forwarding
Auto Port Forwarding allows the DVR to open required ports on your router. This feature only works on certain router models.
Note
Port forwarding is not required to use the Lorex Stratus Connectivity service. For details on setting up re­mote connectivity, see 16 Connecting to Your DVR Over the Internet on PC or Mac, page 72.
To enable Auto Port Forwarding:
1. Select the Network tab.
2. In the Auto Port Forwarding drop-down menu, select Enable or Disable.
3. Click Apply to save your settings.
15.4.3 Changing the DVR’s Client and HTTP Port
The DVR’s Default Client port is 9000. The default HTTP port is 80.
To change the Client port and HTTP port:
1. Select the Network tab.
#LX400012; r. 2.0/12066/12066; en-US
54
Page 65
Using the Main Menu15
2. In Client Port, enter the desired Client Port (default: 9000).
Note
9000 is represented as "09000."
3. In HTTP Port, enter the desired HTTP Port (default: 80).
4. Click Apply to save your settings.
5. Right-click to exit all menus. You will be prompted to restart.
15.4.4 Adjusting Remote Connectivity Streaming Rates
You can adjust the data streaming rate (also called the SubStream) when you connect to the system remotely. If you want to conserve bandwidth, select a lower frame rate and bitrate.
Note
Setting your system to stream with a lower frame and bitrate may cause the video to appear choppy or slow.
To adjust the SubStream settings:
1. Click the SubStream tab.
#LX400012; r. 2.0/12066/12066; en-US
55
Page 66
Using the Main Menu15
2. Configure the following beside the desired channel:
Video: Select Enabled or Disabled. If you select Disabled, you will not be able to
view the channel when connecting remotely to the system.
FPS: Select the desired frames per second.
Bitrate: Select the desired video bitrate.
Audio: Select or de-select the checkbox to enable or disable the system from
streaming audio when viewing the system remotely.
3. Click Apply to save your settings.
15.4.5 Setting up Email Notification
The system can send email notifications when it detects motion. Email notifications can al­so be sent when an alarm device triggers (alarm devices not included; only supported on certain models).
To set up email notification:
1. Click the Email tab in the Network menu.
2. From the Email drop-down menu, select from:
Default: Uses the Lorex email server to send out alarm notifications. This is the rec-
ommended selection.
Enable: Uses custom email server settings.
Disable: Disables email notification.
If you want to use Lorex’s email server (recommended):
1. In the Email drop-down menu, select Default.
2. In the Sender Email field, enter the email address of the sender. This can be any email address of your choice.
3. In the Receiver Email field, enter the email address you want the DVR to send alarm notifications to.
4. In the Interval drop-down menu, enter the duration the DVR must wait before sending out a new notification. For example, if you select a 3 minute interval, the DVR will send out email notifications every 3 minutes until the DVR stops detecting motion / alarm. The DVR will only send out notifications when it detects motion / alarm triggers.
5. Click Apply to save your settings.
#LX400012; r. 2.0/12066/12066; en-US
56
Page 67
Using the Main Menu15
If you select "Enable", and want to use your own email server:
1. Configure the following:
SSL: Select ON/OFF to enable/disable Secure Socket Layer protocol.
SMTP Port: Enter the port used by your SMTP server.
SMTP Server: Enter your SMTP Server address.
Sender Email: Enter the sender email address. This can be any address of your
choice.
Sender Password: Enter your email server’s password.
Receiver Email: Enter the recipient’s email address.
Interval: Enter the interval the DVR waits before sending a new email notification.
2. Click Apply to save your settings.
3. Right-click until you have exited all menus. You will be prompted to restart.
15.4.6 Configuring DDNS settings
Lorex DDNS is available as an optional connectivity option. Please see 25 DDNS Setup (Advanced), page 149 for details.
The primary connectivity option uses Lorex Stratus Connectivity to connect to your system over the Internet without requiring port forwarding or DDNS registration. For details, see 16 Connecting to Your DVR Over the Internet on PC or Mac, page 72.
To configure DDNS settings:
1. Visit http://www.lorexddns.net and register for a DDNS account.
2. Click the DDNS tab.
3. Configure the following:
DDNS: Select Enable.
Server: Select LOREXDDNS (default).
Domain Name: Enter the Domain name/URL Request you received in the email
after registering for DDNS.
User Name: Enter your DDNS User Name.
Password: Enter your DDNS Device password.
4. Click Apply to save your settings.
Note
Please allow 10~15 minutes for the DDNS servers to update with your new DDNS address before at­tempting to connect.
#LX400012; r. 2.0/12066/12066; en-US
57
Page 68
Using the Main Menu15
15.5 Alarm
The Alarm menu allows you to configure Motion Detection and external Alarm devices (not included).
15.5.1 Configuring Motion Detection
Configure motion settings to determine the area you wish to monitor for motion events, and the outcome if a motion event occurs.
To configure motion settings:
1. Select the Motion tab.
#LX400012; r. 2.0/12066/12066; en-US
58
Page 69
Using the Main Menu15
2. Configure the following:
Channel: Select the channel you wish to configure.
Enable: Select Enable or Disable to activate or deactivate motion recording.
Area: Click the Setup button to configure the area of the screen that detects motion.
Click and drag the mouse cursor to configure motion detection areas. Motion detection is enabled in red areas and disabled in transparent areas. Right-click to exit.
Sensitivity: Select motion sensitivity. The greater the number, the greater the
sensitivity.
Alarm Out: Select the checkbox to enable the system to trigger an alarm device
(not included).
Latch Time: Enter the duration alarm devices (not included) will continue to trigger
after the event ends.
Show Message: Select the checkbox if you want the system to display a system
message when an alarm triggers.
Buzzer: Select the duration the system will "beep" when motion is detected. Or se-
lect OFF to disable the "beep" during motion events.
Send Email: Select the checkbox if you want the system to send email notifications
if an alarm triggers. Email notifications must be configured.
Record Channel: Select the channel you wish the DVR to record during motion
recording.
Full Screen: Select the Full Screen check box so that the system goes into full
screen mode when motion or an alarm trigger is detected.
Post Recording: Enter the post recording duration (the time the system continues
to record after a motion event occurs).
3. Click Apply to save your settings.
15.5.2 Configuring Alarm Settings
The Alarm tab allows you to configure how the system behaves when an external alarm device (not included) is triggered.
Note
External alarm devices (such as glass break detectors; not included) are required to configure settings in the Alarm tab. Some models do not support alarm devices. Check the specifications for your DVR to de­termine if it supports alarm devices.
#LX400012; r. 2.0/12066/12066; en-US
59
Page 70
Using the Main Menu15
To configure the Alarm tab:
1. From the Alarm menu, click the Alarm tab.
2. Configure the following:
Alarm In: Select the channel you wish to configure.
Alarm Type: Select the alarm type of the device. Choose from N/O (normally open),
N/C (normally closed).
Alarm Out: Select the checkbox to enable the system’s alarm block to trigger a con-
nected external alarm.
Latch Time: Enter the duration the alarm continues to trigger after the event ends.
Show Message: Select the checkbox if you want the system to display a system
message when an alarm triggers.
Buzzer: Select the checkbox to enable the system to "beep" if an alarm triggers.
Send Email: Select the checkbox if you want the system to send email notifications
if an alarm triggers.
Post Recording: Select the duration the system continues to record as an event
after the alarm trigger ends. For example, if you select 30s (30 seconds), the system continues to record for 30 seconds after the alarm trigger ends.
Full Screen: Select the check box so that the system goes into full screen mode
when motion or an alarm trigger is detected.
3. Click Apply to save your settings.
#LX400012; r. 2.0/12066/12066; en-US
60
Page 71
Using the Main Menu15
15.6 Device
The Device menu allows you to configure and format hard drives, configure PTZ cameras
(not included), and format a USB flash drive (not included).
• For details on connecting PTZ cameras (not included), see 21 Connecting a PTZ Cam-
era (LH150 Series), page 135.
15.6.1 Formatting the Hard Drive
CAUTION
Formatting the HDD erases all data on the hard disk. This step cannot be undone.
1. Select the HDD tab.
2. Click the checkbox under Select to choose the drive you wish to reformat.
3. Click Format HDD.
4. When the warning window appears, click OK. Wait for the system to format the hard drive.
15.6.2 Configuring Overwrite
If Overwrite recording is enabled, the system’s hard drive automatically re-writes the hard drive’s oldest content (first in first out). Otherwise, the system will stop recording when the hard drive is full.
To configure Overwrite:
1. Select the HDD tab.
2. Select the checkbox beside the hard drive you wish to configure.
#LX400012; r. 2.0/12066/12066; en-US
61
Page 72
Using the Main Menu15
3. In the Overwrite drop-down menu, select Auto (recommended), select the desired duration the hard drive should retain its data, or select Disable to disable overwrite.
4. Click Apply to save your settings.
15.6.3 Formatting USB Flash Drives
CAUTION
Formatting a USB flash drive erases all data on the drive. This step cannot be undone.
1. Insert a USB flash drive (not included) into one of the USB ports.
2. In the main menu, click Device>HDD.
3. Click Format USB, then click OK. Wait for formatting to complete.
#LX400012; r. 2.0/12066/12066; en-US
62
Page 73
Using the Main Menu15
15.7 System
The System tab allows you to configure the system time and user accounts.
• For instructions on how to set the system time, including how to setup automatic Day-
light Savings Time adjustments or NTP, see 10 Setting the Date and Time, page 25.
15.7.1 Changing Date Format
You can change the way the system displays the time (i.e. Month, Day, Year)
To change the date format:
1. Select the General tab.
2. In the Date Format drop-down menu, select the desired format. Choose from MM/DD/ YY (Month, Day, Year), YY/MM/DD (Year, Month, Date), or DD/MM/YY (Day, Month, Year).
3. Click Apply to save your settings.
15.7.2 Changing Time Format
You can change the way the system displays the date and time format (i.e 6:00 pm or 18:00).
To change the time format:
1. Select the General tab.
2. In the Time Format drop-down menu, select 12 Hour or 24 Hour.
3. Click Apply to save your settings.
15.7.3 Changing the System Language
1. In the Language drop-down menu, select your desired system language.
2. Click Apply to save your settings.
3. Right-click until you exit the menu. Follow the on-screen instructions to restart your system.
15.7.4 Changing Video Output - NTSC & PAL
To change the video output:
1. In the Video Format drop-down menu, select NTSC or PAL.
2. Click Apply to save your settings.
15.7.5 Configuring Menu Time Out and Auto Logout
The Menu Time Out setting allows you to configure how long the system menu will remain on the screen during inactivity. If passwords are enabled, it also enables the Auto Logout, which allows the system to lock itself after the system is idle for the selected duration.
To configure Auto Logout:
1. Select the General tab. In the Menu Time Out drop-down menu, select the desired time before the system locks itself.
2. Click Apply to save your settings.
Note
You will need your system’s user name and password to unlock the system.
15.7.6 Adding Users & Changing the Admin Password
• For details on changing admin and user passwords, see 14 Managing Passwords, page
36.
#LX400012; r. 2.0/12066/12066; en-US
63
Page 74
Using the Main Menu15
• For details on creating user accounts, see 14.2 Adding Users, page 37.
15.7.7 Viewing System Information
• Click the Info tab.
#LX400012; r. 2.0/12066/12066; en-US
64
Page 75
Using the Main Menu15
15.8 Advanced
The Advanced menu allows you to load system defaults, upgrade the system firmware, and configure automatic firmware updates.
15.8.1 Configuring the "Auto Reboot" Feature
Auto Reboot allows the system to restart during a specified time and date. Restarting the system every so often ensures system stability.
To enable the Auto Reboot feature:
1. Select the Maintain tab.
2. Configure the following:
Auto Reboot: Select Enable or Disable to activate or deactivate the Auto Reboot
feature.
Reboot: In the drop down menu, select how often the system restarts. Choose from
Every day, Every Week, or Every Month. Enter the desired day and time you want the system to restart.
3. Click Apply to save your settings.
15.8.2 Configuring Firmware Upgrades
WARNING
Do not remove the USB flash drive or power off the DVR during the firmware update. Wait for the
system to reboot.
Firmware upgrades can provide improved functionality to your DVR. When firmware up­grades become available, you will automatically be prompted to upgrade your system.
You must have the latest DVR firmware and client software or mobile apps to con­nect to the DVR over the Internet.
You can enable or disable firmware upgrade prompts from appearing.
The system must be connected to the Internet to enable automatic firmware updates.
#LX400012; r. 2.0/12066/12066; en-US
65
Page 76
Using the Main Menu15
To configure firmware upgrade notifications:
1. Select the Auto Upgrade tab.
2. Under Auto Upgrade, select Enable to enable automatic firmware updates. Mes­sages for firmware upgrades will appear on the DVR locally and via client software.
3. Check Check for update to enable local messages on the DVR to notify you for up­dates. The system will check for firmware upgrades every hour.
Note
Click Detect to check for firmware updates manually.
4. Click Apply to save changes.
15.8.3 Upgrading the System Firmware Using a USB Thumb Drive
If your system is not connected to the Internet, you may also download firmware upgrades for free from www.lorextechnology.com and install them manually using a USB thumb drive (not included).
You must have the latest DVR firmware and client software or mobile apps to con­nect to the DVR over the Internet.
To upgrade the system firmware:
1. In your web browser, visit www.lorextechnology.com and search for the model number of your DVR (check the label underneath your DVR for the model number). Download the free firmware upgrade if one is available.
2. Extract the firmware into a blank USB flash drive. The firmware should be in a folder named dvrupgrade. Ensure that this is the only folder in the USB drive.
3. Insert the flash drive into one of the USB ports.
4. Right-click to open the Menu Bar and click the Main Menu button (
).
5. Click Advanced.
#LX400012; r. 2.0/12066/12066; en-US
66
Page 77
Using the Main Menu15
6. Click Firmware Update.
7. Follow the on-screen instructions to update the firmware.
WARNING
Do not remove the USB flash drive or power off the DVR during the firmware update. Wait for the
system to reboot.
15.8.4 Restoring to Factory Default Settings
Restoring to factory default settings reverts any setting changes you have made to their original settings. This does not affect the recordings saved on the DVR. You can reset a single menu, or all menus.
To load system defaults:
1. Right-click to open the Menu Bar and click the Main Menu button (
).
2. Click Advanced. Then click Load Default.
#LX400012; r. 2.0/12066/12066; en-US
67
Page 78
Using the Main Menu15
3. Select the menus that you wish to restore to default settings, or click All to restore the entire system to default settings.
Note
It is recommended to leave the Network menu unchecked when restoring the system to factory de­faults. If you restore the Network menu, you will need to redo remote connectivity setup to access your DVR over the Internet.
4. Click Apply.
5. When the warning window appears, click OK to restore your settings.
6. Click OK to return to the menu.
7. Right-click until you have exited all menus. The DVR prompts you to restart.
15.8.5 Restarting or Shutting Down the DVR
1. Right-click to open the Menu Bar and click the Main Menu button (
2. Click Advanced.
#LX400012; r. 2.0/12066/12066; en-US
).
68
Page 79
Using the Main Menu15
3. Click Reboot or Shut Down.
4. Follow the on-screen instructions to restart or shut down your system.
15.8.6 Configuring System Warnings
The system can send out email notifications, or trigger a connected alarm device (not in­cluded) if it detects system abnormalities. For example, the system can send out a warning if the hard drive is low on storage.
To configure system warnings:
1. Click the Events tab.
#LX400012; r. 2.0/12066/12066; en-US
69
Page 80
Using the Main Menu15
2. Configure the following:
Event Type: Select the event that triggers the system to send out a notification or
alarm trigger. Choose from Disk No Space (low hard drive space), Disk Error (hard drive error), or Video Loss.
Enable: Select Enable or Disable to activate or deactivate the system from send-
ing out notifications.
Alarm Out: Select the checkbox to enable alarm out devices (not included) from
triggering.
Show Message: Select the checkbox for the system to display an error message
when an event occurs.
Send Email: Select the checkbox for the system to send out email notifications
when a system error occurs. Note, email notifications must be configured.
Latch Time: Select the delay duration in the drop-down menu.
Buzzer: Select the buzzer (system beep) duration when the system detects a sys-
tem error.
3. Click Apply to save your settings.
15.8.7 Saving Your System Configuration to a USB Flash Drive
The DVR allows you to save your current system configuration to a USB flash drive (not in­cluded). This is useful if you want to backup your current settings.
Note
This function only saves settings created in system menus. It does not save or backup any video.
To save your system configuration to a USB flash drive (not included):
1. Insert a USB flash drive (not included) into one of the USB ports.
2. Right-click to open the Menu Bar and click Main Menu (
).
3. Click Advanced and select the Maintain tab.
4. Click Save Settings. Wait for the system to save your settings.
15.8.8 Loading a System Configuration from a USB Flash Drive
1. Insert a USB flash drive (not included) that contains a saved configuration to a USB port. See above for details on how to save your DVR configuration.
2. Right-click to open the Menu Bar and click Main Menu (
).
3. Click Advanced and select the Maintain tab.
#LX400012; r. 2.0/12066/12066; en-US
70
Page 81
Using the Main Menu15
4. Click Load Settings. The DVR will load the saved settings from the USB flash drive and then restart.
#LX400012; r. 2.0/12066/12066; en-US
71
Page 82
16
Connecting to Your DVR Over the Internet on PC or Mac
This DVR features connectivity using the exclusive Lorex Stratus Connectivity. This cloud­enabled service allows for Internet connectivity without requiring any network configura­tion. Up to 3 devices may connect to the system at the same time.
This section refers to Internet setup on PC or Mac, for smartphone/tablet setup, see 18 Mobile Apps: Accessing your DVR Using a Mobile Device, page 99.
16.1 System Requirements
Prior to using Lorex Stratus Client, make sure your system meets or exceeds the following system requirements:
Description Requirement
CPU Pentium® 4 or above
Operating System Windows 7/8 Mac OSX 10.6.6 and above (Intel
Memory 256 MB RAM or greater
Video 16 MB of video memory
Network (LAN) 10/100 BaseT Network
Network (WAN) 384 Kbps upload2
Browser
1. For the latest compatibility list, check www.lorextechnology.com, as new software ver-
sions are released to the market
2. An upload speed of 1Mbps is recommended for best video performance
3. If a user connects to the system remotely, there may be slow performance when ac­cessing the system locally. This is normal, and not a malfunction.
16.2 Step 1 of 3: Connect your DVR to Your Router
1. Power off your DVR by disconnecting the power adapter.
2. Connect an Ethernet cable (included) to the LAN port on the rear panel of the DVR. Connect the other end of the Ethernet cable to an empty LAN port (usually numbered 1~4) on your router.
processors only)
Safari 6.0 and above (Mac)
1
1
#LX400012; r. 2.0/12066/12066; en-US
72
Page 83
16
0
DVR System
(may not be exactly as
shown)
local viewing)
Computer
evice ID: xxxxxxxxx
EXAMPLE
Connecting to Your DVR Over the Internet on PC or Mac
3. Reconnect the power adapter to power the DVR back on.
16.3 Step 2 of 3: Obtain the DVR’s Device ID
The Device ID is a unique code that allows your system to handshake with the Lorex serv­ers for a secure connection over the Internet.
To find the Device ID:
1. The Device ID is located on a sticker on the DVR.
You can also find the Device ID by:
• Pressing the
button on the front panel or remote control to open the System In-
formation window.
OR
• Right-clicking and then clicking the Main Menu button (
). Enter the DVR
password (default: 000000). Then click System>Info.
2. Write down the Device ID of the DVR.
#LX400012; r. 2.0/12066/12066; en-US
73
Page 84
16
1 2 3 4 5
6
Connecting to Your DVR Over the Internet on PC or Mac
16.4 Step 3 of 3: Connect to the DVR Over the Internet
Follow the steps below to connect to the DVR over the Internet using a PC or Mac.
Note Make sure to upgrade your DVR to the latest firmware version. You must have the latest DVR firm-
ware and client software to connect to the DVR over the Internet.
PC
1. Download and install the Client Software for PC from www.lorextechnology.com.
2. Once installation is finished, double-click the Lorex Stratus Client icon (
desktop. The DVR login screen appears.
3. Configure the following:
3.1. Under Login Type, select Device ID.
3.2. Under Device ID, enter the DVR’s Device ID. See the label on the top of the
DVR to find the Device ID.
3.3. Under User Name, enter the DVR’s user name (default: admin).
3.4. Under Password, enter the DVR’s password (default: 000000).
3.5. Under Client Port, enter the DVR’s Client Port (default: 9000).
3.6. Click Login.
• If this is the first time connecting to your system, you will be prompted to change the password. Enter a new 6 character password and click OK.
) from the
4. Enter the new password in the login screen and click Login to connect to the DVR. The Client Software connects to your DVR and streams live video from your cameras.
Mac
#LX400012; r. 2.0/12066/12066; en-US
74
Page 85
16
1 2 3 4 5
6
Connecting to Your DVR Over the Internet on PC or Mac
1. Visit www.lorextechnology.com and download the Client Software for Mac.
2. Extract the installer file and double-click it to install.
3. Open Safari, then click Safari>Quit Safari. This resets Safari to complete the installation.
4. Open the Lorex Stratus Client icon (
4.1. Under Login Type, select Device ID.
4.2. Under Device ID, enter the DVR’s Device ID. See the label on the top of the
DVR to find the Device ID.
4.3. Under User Name, enter the DVR’s user name (default: admin).
4.4. Under Password, enter the DVR’s password (default: 000000).
4.5. Under Client Port, enter the DVR’s Client Port (default: 9000).
4.6. Click Login.
• If this is the first time connecting to your system, you will be prompted to change the password. Enter a new 6 character password and click OK.
) from the Applications list.
5. Enter the new password in the login screen and click Login to connect to the DVR. The Client Software connects to your DVR and streams live video from your cameras.
#LX400012; r. 2.0/12066/12066; en-US
75
Page 86
17
1
2
4
5
7
8
6
3
Using the PC/Mac Client Software
Upon login, the Live tab opens. The Client Software interface is the same on PC or Mac.
1. Navigation Tabs: Allows you to access the following tabs:
Live: Watch live video.
Playback: View saved video footage.
Remote Setting: Configure system and networking options.
Local setting: Configure where local files are stored on your hard drive.
Logout: Exits remote viewing.
2. Active Channel List: Displays channels that are currently live.
3. Main Screen: Main display screen for live viewing and playback. You can also drag the screens to any desired position.
4. Viewing options:
5. Split screen Views: Click the desired viewing mode.
6. Mute: Click to mute audio.
: Click to open all connected channels.
: Click to close all connected channels. Note that the system continues to re-
cord when you close channels remotely.
: Previous page.
: Next page.
: Click to open the selected channel in full screen view.
: Click to select the desired split-screen viewing options.
#LX400012; r. 2.0/12066/12066; en-US
76
Page 87
17
0
Using the PC/Mac Client Software
7. Connection Status: Shows the type of connection used.
P2P (peer-to-peer) indicates that the video is streaming directly from the DVR to the
computer running the Client Software.
RLY (relay) indicates that the video is streaming through a Lorex video server. While
relay mode is activated, the system will disconnect after 10 minutes of inactivity. Re­lay mode is only used when a direct connection cannot be made between the DVR and computer.
8. PTZ Controls: PTZ (Pan, Tilt, Zoom) control for connected PTZ cameras (not included).
17.1 Changing Viewing Modes
You can change the number of channels that the system displays simultaneously (i.e. Split-screen Mode, Single-channel Mode, etc.).
To change the DVR’s viewing mode:
• Click one of the following:
• If the controls are not shown, click
.
.
17.2 Taking Screen Shots
The system can take screen shots of a selected channel during live view.
To take a screen shot of a channel:
1. Click
beside the desired channel to capture an image.
2. A pop-up window opens on the bottom left corner of the window. Click Preview to view the image or Folder to show the image in the save folder.
17.3 Recording Video
You can record video footage directly onto your local hard drive. Once the video is in your hard drive, you can back up the video footage onto recordable media such as USB memo­ry keys and blank CD/DVD media.
#LX400012; r. 2.0/12066/12066; en-US
77
Page 88
17
0
0
Using the PC/Mac Client Software
To record video:
1. Click
next to the channel that you wish to capture video from. The video will re-
cord to the default save directory.
2. Click to stop video recording.
17.4 Showing / Hiding Channels
The Active Channel List is a convenient way to show / hide the cameras that display in the main viewing window.
To show or hide video in the main video window:
1. Click
beside the channel number to show a channel. Click again to hide the
channel.
17.5 Viewing the Bit Rate
• Right-click on a channel and click Show Bit rate to display the video bit rate.
#LX400012; r. 2.0/12066/12066; en-US
78
Page 89
17
2
1
Using the PC/Mac Client Software
17.6 Changing the Save Directory of Screenshots or Recorded Video
1. Click the Local Setting tab.
2. Click beside the desired category to browse for a save directory.
3. Select the desired save directory, and then click OK.
4. Click Save to save your changes.
17.7 Changing the Format of Recorded Video (PC Only)
You can change the format of recorded video saved using Remote Surveillance. This al­lows you to directly backup footage from your DVR as an .avi file. This does not affect the format of video files that are backed up locally on the DVR (i.e. using a USB flash drive).
Note
This feature is not available via Mac.
#LX400012; r. 2.0/12066/12066; en-US
79
Page 90
17
Using the PC/Mac Client Software
1. Click the Local Setting tab.
2. Under File Type, select the file format you would like to use when saving video (264 or avi).
3. (Optional) Under Interval, select the maximum length (in minutes) for video saved on the remote computer.
4. Click Save to save your changes.
17.8 Configuring PTZ Settings
The system supports remote PTZ controls for compatible PTZ cameras (not included).
• For details on connecting PTZ cameras to your system, see 21 Connecting a PTZ Cam-
era (LH150 Series), page 135.
To control the PTZ settings on the DVR:
• From the Live tab, double-click to select the channel the PTZ camera is connected to. Use the PTZ control panel to control the pan, tilt, zoom, focus, and iris control of the camera.
#LX400012; r. 2.0/12066/12066; en-US
80
Page 91
17
1
2
3 4
5 6
7 8
9
Using the PC/Mac Client Software
1. Show/Hide PTZ Controls: Click this button to hide/show PTZ controls. Click inside the display area
to pan and tilt the camera.
2. Direction Keys: Click to pan and tilt the camera.
3. Speed Slider: Increase or decrease the pan and tilt speed.
4. Zoom
5. Focus
6. Iris
7. Preset: Click + to save the current camera position as a preset. Click to delete the preset. To go
to a preset, select the number of the preset you would like to go to and then click
8. Cruise: Click
will automatically cycle through saved presets.
9. Video Settings: Use the sliders to adjust the video quality settings of the camera.
to start a cruise. Click to stop the cruise. While cruise is enabled, the camera
.
17.9 Video Playback
Video playback allows you to watch video that has been saved in the DVR’s hard drive.
To playback video:
1. Click the Playback tab.
#LX400012; r. 2.0/12066/12066; en-US
81
Page 92
17
1 2
3
4
Using the PC/Mac Client Software
2. In the calendar window, click the desired month, year, and date. Then, perform the following:
2.1. Under the Type drop-down menu, select the desired recording type you wish to search for
(Continuous, Alarm, or All).
2.2. Check Synchronous playback to play all selected channels at the same time.
2.3. Select the channels you wish to search.
2.4. Click the Search button.
3. Click to begin playback.
#LX400012; r. 2.0/12066/12066; en-US
82
Page 93
17
1
2
3
4
5 6 7 8 9
10 11
12
Using the PC/Mac Client Software
17.9.1 Video Playback Controls
1. Playback Window.
2. Video Content: Drag the line left or right to select the playback time.
3. Volume.
4. Play.
5. Pause.
6. Stop.
7. Step Forward: Click to advance the video by one frame.
8. Take Screenshot.
9. Download: Allows you to download recorded videos to your computer hard drive. To download video, click the channel you want to back up and click the Download content button. A list of files appears. Se­lect the files you want to back up and click Start Download.
10. Play All.
11. Stop All.
12. Speed Slider: Drag the slider to control playback speed.
#LX400012; r. 2.0/12066/12066; en-US
83
Page 94
17
Using the PC/Mac Client Software
17.10 Configuring Display Settings
1. Click the Remote Setting tab, and then click Display>Live.
2. Configure the following:
Channel: Select the channel you want to modify.
Name: Enter the channel name if you want to re-name the channel
Position: Select the position of where the title appears in the channel.
Covert: Enable or Disable covert recording. Covert recording will hide the channel
on the DVR’s local display. You will see be able to see the channel when you log in remotely.
Show Time: Select Enable or Disable to show or hide the time on the DVR’s local
display.
Record Time: Select Enable or Disable to show or hide the record time on the re-
mote display.
3. Click Save to apply your settings.
17.11 Configuring Privacy Zone Settings
CAUTION
Areas covered by privacy zones are not visible in recordings.
You can blank out a certain portion of the channel with a black box.
To configure a privacy zone:
1. Click the Remote Setting tab, and then click Display>Privacy Zone.
2. In the Channel drop-down menu, select the channel you wish to configure.
3. Select the Privacy Zone checkbox to enable privacy masking.
#LX400012; r. 2.0/12066/12066; en-US
84
Page 95
17
Using the PC/Mac Client Software
4. Drag your mouse cursor over the areas you wish to black out. A red box indicates the area that is masked (blocked out).
• To remove a privacy area, click on the red box, then click the Delete button.
5. Click Save to apply your settings.
17.12 Configuring Recording Parameters
1. Click the Remote Setting tab, and then click Record>Rec Parameters.
2. Configure the following:
Channel: Select the channel you wish to configure.
Record: Select Enable or Disable to start or stop system recording.
Pack Duration: Select the duration of each saved file on the system. For example,
if you select 15 minutes, then every file will contain 15 minutes of footage.
Pre-record: Select whether to enable or disable pre-recording.
3. Click Save to apply your settings.
17.13 Configuring the Recording Schedule
1. Click the Remote Setting tab, and then click Record>Schedule.
#LX400012; r. 2.0/12066/12066; en-US
85
Page 96
17
Using the PC/Mac Client Software
2. Configure the following:
Channel: Select the channel you wish to configure.
Week: Select the day of the week you would like to apply the settings to.
The recording schedule is arranged as a grid. Each row represents a recording type (Continuous, Motion, and Alarm), and each box represents an hour.
3. Click the recording grid, and select the type and duration of recording.
4. (Optional) Use the top Copy and Copy To drop-down to copy the recording schedule to a specific day or all days. Click Copy to copy the schedule.
5. (Optional) Use the bottom Copy and Copy To drop-down to copy the recording sched- ule to a specific channel or all channels. Click Copy to copy the schedule.
6. Click Save to apply your settings.
17.14 Configuring System Recording Quality
1. Click the Remote Setting tab, and click Record>MainStream.
2. Under Resolution Mode, select D1 or 960H. If you change the Resolution Mode set­ting, the system will restart once you save your changes.
3. Configure the following:
Channel: Select the channel you wish to apply the settings to.
Resolution: Select the desired recording resolution.
FPS (Framerate): Select the desired recording frame rate. Note that higher frame
rates require greater bandwidth consumption during remote viewing.
Audio: Select whether you want the system to record audio (audio cameras re-
quired, not included).
#LX400012; r. 2.0/12066/12066; en-US
86
Page 97
17
Using the PC/Mac Client Software
4. Click Save to apply your settings.
17.15 Configuring Basic Network Settings
The basic network menu allows you to configure the network protocol type (DHCP or Static).
To configure basic network settings:
1. Click the Remote Setting tab, and click Network.
2. Configure the following:
Type: Select between DHCP or Static. If you select Static, you can edit the IP ad-
dress, Subnet Mask, Gateway, and DNS settings.
Auto Port Forwarding: Select Enable or Disable to enable or disable the Auto
Port Forwarding feature.
3. Click Save to apply your settings.
17.16 Configuring the System Substream
You can adjust the data streaming rate (also called the SubStream) when you connect to the system remotely. If you want to conserve bandwidth, select a lower frame rate and bitrate.
Note
Setting your system to stream with a lower frame and bitrate may cause the video to appear choppy or slow.
#LX400012; r. 2.0/12066/12066; en-US
87
Page 98
17
Using the PC/Mac Client Software
To configure the system’s substream:
1. Click the Remote Setting tab, and click Network>SubStream.
2. Configure the Substream settings:
Channel: Select the channel you wish to apply the settings to.
Resolution: Select the desired recording resolution.
FPS (Framerate): Select the desired recording frame rate. Note that higher frame
rates require greater bandwidth consumption during remote viewing.
Bit Rate: Select the desired video bit rate.
Audio: Select whether you want the system to record audio (audio cameras re-
quired, not included).
3. Click Save to apply your settings.
17.17 Configuring Email Notification Settings
1. Click the Remote Setting tab, and click Network> Email.
2. In the Email drop-down menu, select Default to use the default Lorex email server (recommended) or select Custom to use your own custom SMTP email server.
If you want to use Lorex’s email server (recommended):
1. In the Sender Email field, enter the email address of the sender. This can be any email address of your choice.
#LX400012; r. 2.0/12066/12066; en-US
88
Page 99
17
Using the PC/Mac Client Software
2. In the Receiver Email field, enter the email address you want the DVR to send alarm notifications to.
3. In the Interval drop-down menu, enter the duration the DVR must wait before sending out a new notification. For example, if you select a 3 minute interval, the DVR will send out email notifications every 3 minutes until the DVR stops detecting motion / alarm. The DVR will only send out notifications when it detects motion / alarm triggers.
4. Click Save to save your settings.
If you select "Enable", and want to use your own email server:
1. Configure the following:
SSL: Select ON/OFF to enable/disable Secure Socket Layer protocol.
SMTP Port: Enter your SMTP address.
SMTP Server: Enter your SMTP Server.
Sender Email: Enter the sender email address. This can be any address of your
choice.
Sender Password: Enter your email server’s password.
Receiver Email: Enter the recipient’s email address.
Interval: Enter the interval the DVR waits before sending a new email notification.
2. Click Save to save your settings.
17.18 Configuring DDNS Settings
The primary connectivity option uses Lorex Stratus Connectivity to connect to your system over the Internet without requiring port forwarding or DDNS registration (see 16 Connect- ing to Your DVR Over the Internet on PC or Mac for details). Lorex DDNS is also available as an optional connectivity option (see 25 DDNS Setup (Advanced), page 149 for details).
To configure DDNS settings:
1. Visit http://www.lorexddns.net and register for a free DDNS account.
2. Click the Remote Setting tab, and click DDNS.
#LX400012; r. 2.0/12066/12066; en-US
89
Page 100
17
Using the PC/Mac Client Software
3. Configure the following:
DDNS: Select Enable or Disable.
Server: drop-down menu, select LOREXDDNS.
Domain Name: Enter your Domain name/URL Request from the confirmation
email that was sent after you created your DDNS account.
User name: Enter your DDNS User Name that was emailed to you after DDNS
registration.
Password: Enter your DDNS Device password that was emailed to you after
DDNS registration.
4. Click Save to apply your settings.
17.19 Configuring Motion Detection Settings
1. Click the Remote Setting, and click Alarm>Motion.
2. Configure the following motion recording parameters:
Channel: Select the channel you wish to apply the settings to.
Enable: Select this checkbox to enable motion recording.
Sensitivity: Select the desired motion detection sensitivity. The greater the value,
the greater the motion sensitivity.
Buzzer: Select OFF to disable the buzzer when the system detects a motion event
or select the duration of the buzzer after the system detects a motion event.
Click and drag in the grid to configure motion detection areas.
Red: Motion detection enabled. Clear: Motion detection disabled.
Alarm Out: Select the checkbox to trigger connected alarm devices (not included).
Full Screen: Select the checkbox so that the channel goes into full screen mode
when motion is detected.
Enable Record: Select to enable system recording when motion is detected.
Post Recording: Select the post-recording time after a motion event occurs.
Record Channel: Select the channels that should record during a motion event.
Show Message: Select the checkbox to enable the system to display a warning
message during a motion event.
Send Email: Select the checkbox for the system to send a email notification during
a motion event.
3. Drag your mouse cursor in the window to select the desired area to monitor the chan­nel for motion.
#LX400012; r. 2.0/12066/12066; en-US
90
Loading...