Lippert Components MyRV Programming Manual

MyRV™

PROGRAMMING MANUAL

Rev: 05.19.2016

Page 1

MyRV™ Programming Manual

TABLE OF CONTENTS

Safety and System Information 2

System Information 2

Programming 3

Connecting The MyRV™ Tablet To The MyRV™ Wireless Network 3
Docking Station 3
Wireless Hub And Range Extender 3
MyRV™ Functions 4
Circuit Building For MyRV™ Smart Switch 5
Multifunction Fuse Programming 7

Operation 9

Power On/O 9
Volume Button 9
MyRV™ 10
Notes 11

Safety and System Information

System Information

The MyRV™ tablet is an Android-based device that uses the MyRV™ application to bring system controls and
monitoring software to a touchscreen tablet. The MyRV™ tablet can access the internet (if available), basic how­to RV videos, product videos, owner's manuals and many more RV owner's resources. The systems controlled
and monitored by MyRV™ include slide-outs, leveling systems, awnings, lighting, temperature, water tanks, tire
pressure, battery levels and many more.

The MyRV Control Panel is accessed within the MyRV application on the tablet. When powering on or waking
the tablet, the MyRV application will run automatically as it is pre-configured to do so. In order for the MyRV
application to present the operator with the MyRV Control Panel, there MUST be power to the coach. This will
power the various MyRV controllers located throughout the unit. This will also power the wireless hub and enable
connectivity with the tablet, ultimately allowing wireless connectivity. Please note that with power to the coach,
the tablet should always be able to gain access to the MyRV Control Panel when placed in the docking station due
to it being a wired connection. Use this to assist when diagnosing concerns with the system.

NOTE: After powering up the RV, it may take several minutes (2-5) for the MyRV™ tablet and MyRV™ Hub to

fully energize and communicate. Please allow this time for the system to establish communications
to ensure swift application operations.

Rev: 05.19.2016

Page 2

MyRV™ Programming Manual

Programming

Connecting The MyRV™ Tablet To The MyRV™ Wireless Network

NOTE: Tablet MUST be connected to MyRV™ Wifi Hub to complete the programming process. Placing the

hub in a high location away from appliances such as microwaves and refrigerators will minimize
interference.

1. On the MyRV™ home page, select “Apps & Internet.”

2. On the "Apps and Internet Browser," select the “WiFi Manager.”

3. Locate the MyRV™ Hub (Fig. 1) or Range Extender (Fig. 2) and the label which contains the SSID and

password to the MyRV™ system.

4. Match the SSID on the MyRV™ Hub or Range Extender (Figs. 1A and 2A) to the corresponding SSID in
the "Wifi Manager."

5. Select the SSID and enter the password located on the MyRV™ Hub or Range Extender (Figs. 1B and 2B)
then press "Connect."

NOTE: In order to charge the tablet out of the dock, a 5 volt, 1.8 amp micro USB charger or barrel charging

connector is needed.

Fig. 1

A

B

Docking Station

The MyRV system includes a tablet docking station. This is typically mounted near the center of the coach, and
houses the tablet when the wireless operation is unnecessary or during travel. The docking station is wired to
the coach power system and will charge the tablet during its storage period. The docking station is also wired for
communication with the various controllers in the coach. This allows the tablet to function when stored in the dock
and becomes non-reliant on the wireless hub to do so.

Wireless Hub and Range Extender

The MyRV system is equipped with a wireless hub and range extender. When powered, the hub and range
extender provide the perimeter of the coach with wireless connectivity. This allows the tablet to effectively send
commands wirelessly to the MyRV system. The hub's and range extender's only purpose is to provide wireless
connectivity. The hub and range extender do not keep configuration data, so when troubleshooting wireless
connection concerns, ensure the tablet can operate the MyRV Control Panel when housed in the docking station.
Again, as long as there is power to the coach, the MyRV system should operate from the dock.

Fig. 2

Rev: 05.19.2016

A

B

Page 3

MyRV™ Programming Manual

MyRV™ Functions

1. Press the yellow LincPad Applications icon 5 times (Fig. 3A).

2. A pop-up window will prompt the user to enter password (Fig. 4). The password is the last 4 digits of

the version located in the bottom right hand of the tablet desktop (Fig. 4A).

3. After a password is entered, the Configurator Icon will appear (Fig. 5A). Press the Configurator Icon.

4. To view all components available, press “Show All Devices” (Fig. 6). (A sub list will appear with options:

By product/controller, By functions, By type, Show all devices. )

A

Fig. 3 Fig. 4

A

Fig. 5 Fig. 6

A

Rev: 05.19.2016

Page 4

MyRV™ Programming Manual

5. Select the relay (latching or reversing polarity) switch or tank sensor to assign a title (Fig. 7).

6. When window pops up select “Rename” (Fig. 8).

7. Select “Group”.

8. Select “Name”.

9. Press “Send” to set group and name selected (Fig. 9).

10. Repeat process for each function.

Fig. 7 Fig. 8

Circuit Building For MyRV™ Smart Switch

1. Press “Build Circuit” (Fig. 10).

Fig. 9

Fig. 10

Rev: 05.19.2016

Page 5

MyRV™ Programming Manual

2. Select first device by pressing the preferred icon. Then press Select when the pop-up window shows
up on the screen (Fig. 11). Device title will highlight in yellow (Fig. 12).

3. Repeat process for each device included in the circuit.

4. Once you have selected (highlighted) all devices for the circuit, press one of the highlighted device

icons. Press “Create Circuit” in pop-up window (Fig. 13). The next screen will show all devices included
in the circuit and assign a circuit number (Fig. 14).

Fig. 11 Fig. 12

Fig. 13 Fig. 14

Rev: 05.19.2016

Page 6

MyRV™ Programming Manual

Multifunction Fuse Programming

1. Enter the MyRV configurator screen by tapping the yellow LincPad Applications icon five (5) times (Fig.
15A). You will then be prompted to enter a four-digit password (Fig. 15B). The password is the last four
digits of the version number (Fig. 15C).

2. Choose the "Configurator" option (Fig. 16A).

A

Fig. 15 Fig. 16

C

B

A

3. Choose the "Show All Devices" option (Fig. 17A).

4. Choose the "By Product/Controller" option (Fig. 18A). This will display all of the products and

controllers connected to the Linc system.

5. Press and HOLD the "Multifunction 8-Output" option (Fig. 19A). You will then be prompted to
configure the fuses. Choose "OK" (Fig. 20A) to enter fuse configuration.

Fig. 17 Fig. 18

A

Fig. 19 Fig. 20

A

Rev: 05.19.2016

Page 7

A

A

MyRV™ Programming Manual

6. When in the fuse configuration menu, a list of all labeled and unlabeled relay functions will appear (Fig.

21). Select the fuse location from the drop down menu on the right (Fig. 21A and Fig. 22).

Fig. 21

Fig. 22

A

7. Once all fuse locations are chosen, press and HOLD anywhere on the screen for a pop up menu

confirming the fuse locations. Press and hold the sync button on the multifunction receiver (Fig 23A).
While holding the sync button, press "OK" on the "Send All" prompt (Fig. 24A). This will program all
fuse positions.

Fig. 24

Fig. 23

A

A

Rev: 05.19.2016

Page 8

MyRV™ Programming Manual

Operation

Power On/Off

1. To power ON the tablet, hold and release the power button for 2-3 seconds (Fig. 25).

NOTE: It will take a few moments to start up and load the system.

2. To enter or exit sleep mode, press and release power button.

3. To power OFF the tablet, press and hold the power button until a utility screen appears.

4. Select "Power off".

5. Press “OK” when confirmation box displays: “Your tablet will shut down.” (Fig. 27).

Volume Button

1. Volume control is located on the side of the tablet (Fig. 25). There is also a volume icon on the menu
screen.

Fig. 25

Fig. 26

Microphone

Power Button

Headphone Jack

Micro USB

Charging Port

Volume Control

TF/Micro SD

Card Port

Reset

Fig. 27

Rev: 05.19.2016

Page 9

MyRV™ Programming Manual

MyRV™

1. Locate the “MyRV Control Panel” on the menu screen (Fig. 28A).

2. Pushing the “MyRV Control Panel” tab will open the “MyRV™ Applications” screen. This screen will

display all the icons of the devices on the RV that can be operated with the MyRV™ Tablet.

3. Push the icon of the device you wish to operate.

4. Push the “Home” icon button, located in top right of screen, to return to “MyRV™ application” screen.

NOTE: MyRV includes text and video resources, including owner’s manuals and troubleshooting videos.

Fig. 28

A

Rev: 05.19.2016

Page 10

MyRV™ Programming Manual

Notes

Rev: 05.19.2016

Page 11

MyRV™ Programming Manual

The contents of this manual are proprietary and copyright protected by Lippert Components, Inc. (“LCI”).

LCI prohibits the copying or dissemination of portions of this manual unless prior written consent from an

authorized LCI representative has been provided. Any unauthorized use shall void any applicable warranty.

The information contained in this manual is subject to change without notice and at the sole discretion of LCI.

Revised editions are available for free download from

Please recycle all obsolete materials.

For all concerns or questions, please contact

Lippert Components, Inc.

Ph: [phone] | Web:

Rev: 05.19.2016

Page 12

MyRV™ Programming Manual