Lippert Components Level Up User Manual

Level-Up® (Towable) System

OWNER'S MANUAL

Rev: 12.15.2014

Page 1

Level Up Towable Owner's Manual

TABLE OF CONTENTS

System and Safety Information 2
Introduction 3
Touch Pad Diagram 3
Prior to Operation 4
Operation 4

Basic Jack Operation 4

5th Wheel Operation 4

Unhitching Instructions 4
Auto Level 5
Auto Level Sequence 5
Hitch Recognition 5

Travel Trailer Operation 6

Unhitching Instructions 6
Auto Level 6
Auto Level Sequence 6
Hitch Recognition 6

Manual Operation 7
Zero Point Calibration 8
Maintenance 8
Troubleshooting 8

Error Display in LCD Screen 8

Manual Override 9

System and Safety Information

• Be sure to park the unit on solid, level ground.

• Ensure all jack landing locations are cleared of debris and obstructions and also free of depressions.

• When parking the unit on extremely soft surfaces, utilize load distribution pads under each jack.

• People and pets should be clear of unit while operating leveling system.

• Be sure to keep hands and other body parts clear of fluid leaks. Oil leaks in the Lippert Leveling

System may be under high pressure and can cause serious skin-penetrating injuries.

Lippert Components Inc. recommends that a trained professional be employed to change the tires on the

unit. Ensure that the unit is properly supported with jack stands, or other adequate devices, under the

frame of the unit prior to commencing any service or repair procedure. Any attempts to change the tires or

perform other service while unit is supported solely by the LCI Level-Up® with Automatic Leveling System

could result in death, serious injury, unit or property damage.

Rev: 12.15.2014

Page 2

Level Up Towable Owner's Manual

Introduction

Level-Up® is an Automatic Leveling system. This system is equipped with 14K aluminum landing gear and 8K
aluminum leveling jacks. The jacks in the Level-Up® system work in pairs.

Touch Pad Diagram

Fig. 1

D

A

E

K

B

C

F

H

G

I

J

Rev: 12.15.2014

Callout Description

A Up Arrow - Scrolls up through the menu on LCD.
B Down Arrow - Scrolls down through the menu on LCD.
C Enter - Activates modes and procedures indicated on LCD.
D Retract - Places leveling system into retract mode - Manual mode ONLY.

E LCD Display - Displays procedures and results.

F Auto Level - Places leveling system into auto level mode.
G Front Button - Activates both front jacks.
H Left Button - Activates left leveling jack(s) in manual mode.

I Right Button - Activates right leveling jack(s) in manual mode.

J Rear Button - Activates leveling jacks in manual mode.

K Power Button - Turns leveling system on and off.

Page 3

Level Up Towable Owner's Manual

Prior to Operation

The leveling system shall only be operated under the following conditions:

1. The unit is parked on a reasonably level surface.

2. Be sure all persons, pets and property are clear of the unit while LCI Level-Up® Automatic System is in

operation.

3. Ensure the battery of the unit is fully charged or that the unit is plugged into shore power prior to
attempting to operate the system. Level-Up® requires a minimum of 12 VDC from the battery for
proper operation.

Operation

Basic Jack Operation

1. Landing gear Jacks

Landing gear jacks can be operated any time the system is “ON” but NOT in the “AUTO MODE.” By pushing
the “FRONT” button (Fig. 1G), both front or landing gear jacks can be extended. If the touch pad is put in the
“RETRACT” mode, indicated by the orange illuminated LED next to the “RETRACT” button (Fig. 1D), the front
jacks can be retracted together by pushing the “FRONT” button.

2. Level-Up® jacks

The Level-Up® jacks operate when the “AUTO MODE” is activated or the touch pad is in the “MANUAL
MODE.” Once system is in “MANUAL MODE,” pressing the “REAR” button (Fig. 1J) will extend all Level-Up®
jacks at the same time. Press the “LEFT” or “RIGHT” buttons (Fig. 1H and 1I) to operate Level-Up® jacks on
the left or right side of the unit, respectively.

5th Wheel Operation

Unhitching Instructions

1. Push touch panel “ON/OFF,” (Fig. 1K) to turn system on. LCD Screen (Fig. 1E) lights up.

2. LCD will display status … “NOT LEVEL JACKS: UP" (Fig. 2A).

NOTE: Orange arrow lights (Fig. 2B) may come on, indicating the current disposition of the unit.

3. Push "FRONT" button (Fig. 1G) to extend landing gear jacks and lift front of unit to take the weight of

the 5th wheel off of the hitch.

4. Uncouple the 5th wheel connection on the tow vehicle.

5. Pull tow vehicle away and park at a safe distance.

Fig. 2

A

B

Rev: 12.15.2014

Page 4

Level Up Towable Owner's Manual

Auto Level

NOTE: Prior to unhitching from the tow vehicle, ensure unit is parked on a level surface and chock the tires

of the unit.

1. After unhitching from tow vehicle press "AUTO LEVEL" (Fig. 1F).

NOTE: Pressing any button during an Auto Level sequence will abort the auto leveling cycle.

NOTE: In order for hitch recognition feature to function, the auto level sequence MUST be started with the

front of the unit above level.

Auto Level Sequence

1. Front landing gear retract, lowering the front of the unit below level, stopping, then lifting the front
end to level the unit front to back.

2. The left side leveling jack(s) extend and raise the roadside of the unit.

3. The right side leveling jack(s) extend and raise the curbside of the unit, beginning side to side leveling.

4. The front landing gear extend to complete the leveling cycle.

NOTE: Additional left to right or front to back leveling may occur if the controller deems necessary.

NOTE: If the auto level sequence does not happen as stated above, check to ensure proper manual function

in all zones.

Hitch Recognition

1. Turn on touch pad.

2. Press the "LEFT" and "RIGHT" buttons simultaneously (Fig. 1H and 1I).

3. The front of the unit will raise to the height where the auto level sequence was started.

NOTE: If the auto level sequence was started with the front of the unit in a below level condition, the Hitch

Recognition will not function and the LCD will display “Feature Disabled." In order for the hitch
recognition feature to function, the auto level sequence MUST be started with the front of the unit
above level.

4. Connect tow vehicle and make sure 5th wheel and hitch are connected and locked.

5. Push “UP” arrow (Fig. 1A) until ”AUTO RETRACT” appears in LCD screen.

6. Push “ENTER” (Fig. 1C). System will immediately retract all jacks.

Rev: 12.15.2014

Page 5

Level Up Towable Owner's Manual

Travel Trailer Operation

Unhitching Instructions

NOTE: Prior to unhitching from the tow vehicle, ensure unit is parked on a level surface and chock the tires

of the unit.

1. Push “ON/OFF” button (Fig. 1K) to turn system “ON” (green light).

2. Push “UP” (Fig. 1A) or “DOWN” arrow (Fig. 1B) to scroll through features to “MANUAL MODE” in

display.

3. Push “ENTER” (Fig. 1C).

4. Push “FRONT” button (Fig. 1G) to extend front jacks to the ground until the trailer is unhitched from

the tow vehicle.

NOTE: The Power Tongue Jack should ONLY be used when storing the trailer.

Auto Level

NOTE: The Power Tongue Jack MUST be retracted prior to starting auto level sequence (Fig. 3 shows the

LCD alert).

1. After unhitching from tow vehicle press "AUTO LEVEL" (Fig. 1F).

Fig. 3

NOTE: Pressing any button during an Auto Level sequence will abort the auto leveling cycle.

NOTE: In order for hitch recognition feature to function, the auto level sequence MUST be started with the

front of the unit above level.

Auto Level Sequence

1. Front jacks retract, lowering the front of the unit below level, stopping, then lifting the front end to
level the unit front to back.

2. The rear left side leveling jack extends and raises the roadside of the unit.

3. The rear right side leveling jack extends and raises the curbside of the unit, beginning side to side

leveling.

4. The front jacks extend to complete the leveling cycle.

NOTE: Additional left to right or front to back leveling may occur if the controller deems necessary.

NOTE: If the auto level sequence does not happen as stated above, check to ensure proper manual function

in all zones.

Hitch Recognition

1. Turn on touch pad.

2. Press the left and right buttons simultaneously (Fig. 1H and 1I).

3. The front of the unit will raise to the height where the auto level sequence was started.

Rev: 12.15.2014

Page 6

Level Up Towable Owner's Manual

NOTE: If the auto level sequence was started with the front of the unit in a below level condition, the

Hitch Recognition will not function and the LCD will display “Feature Disabled.” In order for hitch
recognition feature to function, the auto level sequence MUST be started with the front of the unit
above level.

4. Connect tow vehicle and make sure travel trailer and hitch are connected and locked.

5. Push “UP” arrow until ”AUTO RETRACT” appears in LCD screen.

6. Push “ENTER.” System will immediately retract all jacks.

Manual Operation

1. Front landing gear (5th Wheels) or Front jacks (Travel Trailers)

NOTE: The landing gear or front jacks will operate manually any time system is “ON” except in “AUTO

MODE.”

A. Push “ON/OFF” (Fig. 1K) to turn system on.

B. Push “UP” arrow (Fig. 1A) once or until screen reads “MANUAL MODE” (Fig. 4).

C. Push “ENTER” (Fig. 1C) once while screen reads “MANUAL MODE" Fig. 4).

D. Push “FRONT” (Fig. 1G) to extend front landing gear or front jacks.

E. Push “RETRACT" (Fig. 1D) and orange LED (Fig. 5) comes on.

F. Push “FRONT” (Fig. 1G) to retract front landing gear or front jacks.

NOTE: If orange LED (Fig. 5) is on, landing gear or jacks will retract. If orange LED (Fig. 5) is off, landing gear

or jacks will extend.

G. Push “ON/OFF” to turn system off.

H. After 3 minutes system will turn off by itself.

Fig. 4 Fig. 5

2. Level-Up® jacks - EXTEND

A. Turn “ON/OFF” button “ON."

B. Push scroll arrow to display “MANUAL MODE” (Fig. 4).

C. Push “ENTER" button, “MANUAL MODE” displayed (Fig. 4).

NOTE: By pushing “RIGHT,” passenger side Level-Up® jacks operate. By pushing “LEFT,” driver side Level-Up®

jacks operate, and so on.

3. Level-Up® jacks - RETRACT

A. Push “RETRACT" and orange LED (Fig. 5) will come on.

B. Push “REAR” to retract all Level-Up® jacks.

C. To extend, the “RETRACT“ light (Fig. 5) should be off.

NOTE: The side to side movement in manual mode is limited to 5o of tilt.

Rev: 12.15.2014

Page 7

Level Up Towable Owner's Manual

Zero Point Calibration

1. Turn “ON/OFF” button (Fig. 1K) on.

2. Push “FRONT” button (Fig. 1G) 10 times.

3. Push “REAR” (Fig. 1J) button 10 times.

4. Control will flash and beep, LCD will say “ZERO POINT CALIBRATE.”

5. To memorize this level condition, press “ENTER” (Fig. 1C).

6. LCD will say “ZERO POINT STABILITY SUCCESSFULLY SET.”

7. The control will then turn off.

Maintenance

1. Each month, check that the fluid level is within 1/4" of the fill spout lip while jacks and slide-outs are

fully retracted.

NOTE: Always fill the reservoir with the jacks and slide-outs in the fully retracted position. Filling reservoir

when jacks and slide-outs are extended will cause reservoir to overflow into its compartment when
jacks and slide-outs are retracted.

2. Inspect and clean all power unit electrical connections prior to the first use of the unit of the season
and prior to storing the unit. If corrosion is evident, clean all corrosion with a wire brush and apply
dielectric grease to the connections.

3. Remove dirt and road debris from jacks as needed.

4. If jacks are down for extended periods, it is recommended to spray exposed leveling jack rods with a

silicone lubricant every three months for protection. If the unit is located in a salty air environment, it is
recommended to spray the rods every 4 to 6 weeks.

Troubleshooting

Error Display in LCD Screen

NOTE: To clear Error Code, push "ENTER" - If error remains, the code will appear again.

LCD Message What's Happening? What Should I Do?

"EXCESS ANGLE"

"BAD CALIBRATION" Unit zero point was not set correctly. Reset zero point. See "Calibration."

"FEATURE DISABLED"

"LOW VOLTAGE"

"OUT OF STROKE"

Unsecured controller.

Uneven or sloped site.

Front of unit below level when
starting Auto Level process.

Bad connection or wiring.

Discharged or bad battery.

Unsecured controller.

Uneven or sloped site.

Check and secure controller placement.

Relocate the unit.

Raise front of unit above level and restart Auto
Level process.

Check wiring - repair or replace.

Test battery voltage under load - charge or
replace.

Check and secure controller placement.

Relocate the unit.

"EXTERNAL SENSOR" Bad connection or wiring.

"JACK TIME OUT"

"AUTO LEVEL FAILURE"

Rev: 12.15.2014

System could not level in expected
time.

Unsecured controller.

Voltage drop.

Page 8

Replace or repair connection to rear remote
sensor.

Check for obstructions, leaks, fluid level and
voltage to power unit motor under load.

Check and secure controller placement.

Test battery voltage under load - charge or
replace.

Level Up Towable Owner's Manual

Manual Override

The LCI Level-Up® Automatic Leveling System can be manually operated with an electric drill. In the event of
electrical or system failure, this manual method of extending and retracting the jacks can be used. See the
instructions below.

NOTE: Unhook the power unit motor from the power source prior to attempting the manual override

procedure.

1. Locate the valves that are paired with the landing gear or leveling jack to be manually overridden.

A. Landing Gear - Valve located on the landing gear (Fig. 6).

B. Leveling Jacks - Valve located on manifold (Fig. 7).

2. Using a 5/32” hex wrench, open the valve by turning the manual override set screw clockwise (Fig. 8A).

3. Remove protective label (Fig. 9A) from power unit to reveal the manual override coupler.

4. Using an electric drill with a 1/4" hex bit, insert the hex bit into the manual override coupler to

manually operate the Level-Up system (Fig. 10).

A. Run the drill forward (clockwise) to retract the landing gear or leveling jack (Fig. 10A).

B. Run the drill in reverse (counterclockwise) to extend the landing gear or leveling jack (Fig. 10B).

5. Be sure to turn the manual override set screw on the valve (Fig. 11A) back to the counterclockwise

position after extending or retracting the landing gear or leveling jack.

Fig. 6

Fig. 9

Fig. 7

Fig. 10

Fig. 8

A

Fig. 11

Rev: 12.15.2014

A

A

A

B

Page 9

Level Up Towable Owner's Manual

All information contained within may be distributed as a full document only, unless otherwise permitted by

explicit consent of Lippert Components Inc. to distribute individual parts.

All information contained within is subject to change without notice. New editions will be posted on www.lci1.

com and can be downloaded for free. Information contained within is considered factual until made obsolete

by a *NEW* revision.

Please recycle all obsolete materials.

For all concerns or questions, please contact

Lippert Components, Inc.

Ph: [phone] Web: www.lci1.com Email: [e-mail]

Rev: 12.15.2014

Page 10

Level Up Towable Owner's Manual