Lippert Components In Wall Slide-Out System Winnebago Industries User Manual

LIPPERTCOMPONENTS, INC.

Schwintek in-wall™ Slideout SyStem

winnebago induStrieS - owner’S manual

Error codes

During operation when an error occurs the board will use the led’s to indicate where the problem
exists.

For motor specic faults the green led will blink 1 time for motor 1, and 2 times for motor 2. The red
led will blink from 2 to 9 times depending on the error code.

The error codes are as follows:
2 Battery drop out: Battery capacity low enough to drop below 6 volts while running
3 Low battery: Voltage below 8 volts at start of cycle
4 High battery: Voltage greater than 18 volts
5 Excessive motor current: High amperage, also indicated by 1 side of slide continually stalling.
6 Motor short circuit: Motor or wiring to motor has shorted out.
8 Hall signal not present: Encoder is not providing a signal. Usually a wiring problem.
9 Hall power short to ground: Power to encoder has been shorted to ground. Usually a wiring

problem.

When an error code is present, the board needs to be re-set. Energizing the extend/retract switch
resets the board. Energize the extend/retract switch again for normal operation.

WARNING!

DO NOT MOVE THE RV UNLESS THE MOTORS ARE PLUGGED IN!

revWNBG2

Manual Override - C1 & C2 versions

1. Electronic Manual Override (available on board revision C1 and newer)

Locate the circuit board

Press the “mode button” six times quickly, press a 7th time and hold for approximately

5 seconds.

Mode Button

The red and green LED lights will begin to ash, conrming the override mode.

Release mode button.

Back inside coach; use the normal slide control switch to retract the room.
A video demonstrating this technique can be found on the internet.
Follow this link: http://www.youtube.com/watch?v=ymt1Uesf0Pc

2. Disengage motors, manually retract room and travel lock.

Motor Retention Screw

Repeat this process for both sides of slide room.
Push or pull room back in to opening, keep both sides relatively even.
The room must be travel locked to keep room in place for road travel.
A video demonstrating this technique can be found on the internet.
Follow this link http://www.youtube.com/watch?v=ymt1Uesf0Pc

Locate and remove motor retention screw
located near top of each vertical column.

Bend back wipe seal and
visually locate motor

1/2”

Pull the motor up until
disengaged, about ½”

Trouble shooting ow chart

Checking Fuses

The Schwintek In-Wall™ Slide requires a minimum of 30 amp fuse. Check the 12 volt fuse box for
blown fuses, and replace any if necessary. Consult the rv manufacturers documentation for the
location of the 12 volt fuse box, and the location of the Room Slide Controller’s fuse. If the fuse blows
immediately upon replacement, there is a problem with the wiring to the In-Wall™ Slide control box.
Have qualied service personnel check and repair.

Obstructions

Check outside the rv for possible obstructions: tree, post, car, etc… Check inside the rv for any
obstructions: luggage, furniture, open cabinets, etc… Also check for smaller objects that may be
wedged under the oor or in the sides of unit. Remove obstructions before proceeding.

Error Codes

Consult rv manufacturer’s documentation for the location of the In-Wall™ Slide Controller. See page 1
for a description of the error codes, and possible problems.

Low Voltage

The Schwintek In-Wall™ Slide Controller is capable of operating the room with as little as 8 volts.
But at these lower voltages the amperage requirement is greater. Check voltage at the controller. If
voltage is lower than 11 volts, it is recommended that the battery be placed on a charger until it is
fully charged. It may be possible to ’jump’ the rv’s battery temporarily to extend or retract the room.
Consult the rv manufacturer’s owners manual on the procedure for ‘jumping’ or charging the battery.

**********Never ‘jump’ or charge the battery from the power connections on the In-Wall™

Only 1 side moving

The Schwintek In-Wall™ Room Slide has a separate motor to operate each side of the room. Does
only 1 side of the room move a short distance (2 to 4 inches) and stop.

Will non moving side move with help?
If only 1 side of the room is moving, then with someone’s assistance press the switch to extend or
retract the room while pushing the non moving side in the appropriate direction. On larger rooms it
may be necessary to have 2 or more people pushing the room.

Non moving side moved manually

Try to push the non moving side in and out. If a motor shaft has broken then it will be possible to
move that side of the room several inches by hand. Larger rooms may require several people to push.

Debris in the rack

Check all 4 gear racks on the side of the room for debris.

Do status led’s light

Consult the rv manufacturers documentation for the location of the Room Slide Controller. When the
room slide direction switch is actuated, do the status led’s light up. Check this in both the extend and

retract modes.

Controller. Always do this at the battery.*****************

IF YOU HAVE ANY PROBLEMS OR QUESTIONS; CONSULT

YOUR LOCAL AUTHORIZED DEALER OR CONTACT LIPPERT

PHONE: [phone] - E-MAIL: [e-mail]