Linksys MNFSPA2100, SPA2100 User Manual

Power off your network
devices, inclucing your
modem/router and PC.

Model No.

Quick Installation Guide

Model No.

Voice

D Connect one end of an

Ethernet network cable
(included) to the ETHERNET
port of the ATA. Connect
the other end to the
Ethernet port of your PC.

E Connect one end of a

different Ethernet network
cable to the INTERNET port
of the ATA. Connect the
other end to your cable/DSL
modem/router.

F Power on the cable/DSL

modem/router.

G Connect the included

power adapter to the
ATA’s power port, and then
plug the power adaptor into
an electrical outlet.

H Power on your PC.

A Launch the web browser on

the PC.

B Enter http://192.168.1.1/

in the Address field
(192.1681.1 is the default
local IP address of the ATA).
Then press the Enter key.

C The Router - Status screen

will appear. Click the WAN
Setup tab.

MNFSPA2100

Analogue telephone Adaptor

D Proceed to the appropriate

instructions for your Internet
Connection Type: DHCP,
Static IP, or PPPoE.

Select DHCP for the
Connection Type.

3

Click Submit All Changes.

Static IP

1 Select Static IP for the

Connection Type.

2 In the Static IP Settings

section, enter the IP
address in the

Static IP

field,

the subnet mask in the

NetMask

field, and the
default gateway IP address
in the

Gateway

field.

Package Contents

• MNFSPA2100 VoIP ATA

• 5 V Power Adaptor

• RJ-45 Ethernet Cable

• MNF Welcome Guide

• Quick Installation Guide

D

E

G

NOTE:

Make sure your PC’s
Ethernet adapter is set to obtain an IP
address automatically. For more
information, refer to Windows Help.

A

B

Connect one end of the
telephone cable to the
ATA’s PHONE 1 port.
Connect the other end to
your analogue telephone
or fax machine.

C Repeat Step B with the

PHONE 2 port if you have an
additional telephone or fax
machine to connect.

1

Make sure you have the following:

• An active Internet connection

• A cable/DSL modem/router

• An analogue telephone or fax machine with an RJ-11 phone cable

• A PC will be required for the initial setup of your Internet connection.

B

IMPORTANT: Do not connect the

PHONE port to a telephone wall jack.
Make sure you only connect a
telephone or fax machine to the
PHONE port. Otherwise, the ATA or
the telephone wiring in your home
or office may be damaged.

C

Configure the Phone Adapter

2

D

C

Static IP

Connect the ATA

Before You Begin

DHCP

3 In the Optional Settings

section, enter the DNS
server address(es) in the

Primary DNS

and optional

Secondary DNS

fields.

4 Click Submit All Changes.

PPPoE

1 Select P

PPPoE

for the

Connection Type.

2 Enter the user name in the

PPPoE Login Name

field,
and enter the password in
the

PPPoE Login Password

field.

Click Submit All Changes.

PPPoE

Please proceed to
step 2

Please note the following connection types:

DHCP: Use this connection for Cable
Broadband if the MNFSPA2100
connects directly to an existing router.
Static IP: Assign your own private IP address to
the MNNSPA2100. Suitable if
connecting to an existing router.
PPPoE: Connect the MNFSPA2100 directly to
the DSL modem.

Please note the MNFSPA2100 is pre-configured with the MyNetFone service.

E Verify that your PC is now connected to the internet. You can do this

by launching a web brower and entering www.mynetfone.com.au
in the address field.

Register with MyNetFone

If you purchase the adaptor from MyNetFone website, the registration
will have been done online at the time of your purchase.

By registering and completing the Service Registration Form below, you’ll
be able to select the service option that best suits your individual needs:

www.mynetfone.com.au/register

Call your friend

Making a phone call with MyNetFone service is no different from any
other calls that you make every day.
Just dial the normal phone number and your call will be connected.
To make a free call to another MyNetFone user, simply dial their
MyNetFone number (09xx xxxx).

NEED HELP?

We realise it’s not always smooth sailing. As with any new services you
may encounter some questions or problems. Check out our FAQ section
on our website first:
www.mynetfone.com.au/faq

If you still have questions, please do not hesitate to call our national
Customer Care Centre, on:

1300 731 048

When you call, please make sure you’re next to your computer with your
broadband Internet connected in order for our staff to assist straight
away. Alternatively, you can send an email to our support team:

[e-mail]

We’ll get back to you as soon as possible!

This section explains how to use the Interactive Voice Response Menu to
configure the ATA’s network settings. You will use the telephone’s keypad to
enter your commands and select choices, and the ATA will use voice
responses.

To access the Interactive Voice Response Menu:

A Use a telephone connected to the PHONE port of the ATA (You can

only access the Interactive Voice Response Menu through an
analogue telephone, not any of the Internet phones.)

B Press *

****

(in other words, press the star key four times).

C Wait until you hear the “Linksys configuration menu—please enter the

option followed by the # (pound) key or hang up to exit” response.

D Refer to the following table that lists actions, commands, menu

choices, and descriptions. After you select an option, press the #

#

(pound) key. To exit the menu, hang up the telephone.

While entering a value, such as an IP address, you may exit without entering
any changes. Press the *

*

(star) key twice within half a second. Otherwise,

the * will be treated as a decimal point or dot.

After entering a value, such as an IP address, press the #

#

(pound) key to

indicate you have finished your selection. To save the new setting, press 1

1

.

To review the new setting, press 2

2

. To re-enter the new setting, press 33. To

cancel your entry and return to the main menu, press *

*

(star).

For example, to enter the IP address

191.168.1.105

by keypad, press these

keys: 1

191*168*1*105

. Press the ## (pound) key to indicate that you have

finished entering the IP address. Then press 1

1

to save the IP address or press

the *

*

(star) key to cancel your entry and return to the main menu.

If the menu is inactive for more than one minute, the ATA will time out.
You will need to re-enter the menu by pressing ****.

Using the Interactive Voice
Response Menu

Using the Interactive Voice Response Menu

The settings you have saved will take effect after you hang up the
telephone. The Phone Adapter may reboot at this time.

Interactive Voice Response Menu

Action Command Choices Description

Enter Interactive Voice
Response Menu

**** Use this command to enter the

Interactive Voice Response Menu. Do not
press any other keys until you hear,
“Linksys configuration menu. Please
enter the option followed by the #
(pound) key or hang up to exit.”

Check Internet
Connection Type

100 Hear the Internet connection type of the

Phone Adapter.

Check Internet IP
Address

110 Hear the IP address assigned to the

Phone Adapter’s Internet (external)
interface.

Check Network Mask
(or Subnet Mask)

120 Hear the network or subnet mask

assigned to the Phone Adapter.

Check Gateway IP
Address

130 Hear the IP address of the Phone Adapter

(usually the network router).

Check MAC Address 140 Hear the MAC address of the Phone

Adapter in hexadecimal string format.

Check Firmware
Version

150 Hear the version number of the firmware

running on the Phone Adapter.

Check Primary DNS
Server IP Address

160 Hear the IP address of the primary DNS

(Domain Name Service) server.

Check Internet Web
Server Port

170 Hear the port number of the Internet Web

server used for the Web-based Utility.

Check Local IP
Address

210 Hear the local IP address of the Phone

Adapter.

Set Internet
Connection Type

101 DHCP - Press 0.

Static IP ­Press 1.
PPPoE - Press 2.

Select the type of Internet connection
you are using. Refer to the
documentation supplied by your Internet
Service Provider (ISP).

Factory Reset 73738 Confirm -

Press 1.
Cancel - Press
* (star).

This feature may be protected by a
password available only from your ITSP.
If necessary, enter the password*. The
Phone Adapter will request confirmation;
enter1 to confirm. You will hear, “Option
successful.” Hang up the phone. The
Phone Adapter will reboot, and all
settings will be reset to their defaults.

User Factory Reset 877778 Confirm -

Press 1.
Cancel - Press
* (star).

The Phone Adapter will request
confirmation; enter 1 to confirm. You will
hear, “Option successful.” Hang up the
phone. The Phone Adapter will reboot
and all user-configurable settings will be
reset to their factory default settings.

Interactive Voice Response Menu

Action Command Choices Description

SPA2102-QI-60613A DF

Linksys is a registered trademark or trademark of
Cisco Systems, Inc. and/or its affiliates in the U.S.
and certain other countries. Copyright © 2006
Cisco Systems, Inc. All rights reserved.

Set Static IP Address 111 First, set the Internet Connection Type to

static IP address; otherwise, you will
hear, “Invalid Option,” if you try to set the
static IP address. Use the * (star) key
when entering a decimal point.

Set Network (or
Subnet) Mask

121 First, set the Internet Connection Type to

static IP address; otherwise, you will
hear, “Invalid Option,” if you try to set the
network or subnet mask. Use the * (star)
key when entering a decimal point.

Set Gateway IP
Address

131 First, set the Internet Connection Type to

static IP address; otherwise, you will
hear, “Invalid Option,” if you try to set the
gateway IP address. Use the * (star) key
when entering a decimal point.

Set Primary DNS
Server IP Address

161 First, set the Internet Connection Type to

static IP address; otherwise, you will
hear, “Invalid Option,” if you try to set the
IP address of the primary DNS server.
Use the * (star) key when entering a
decimal point.

Set the Mode 201 Router/NAT

Mode - Press 0.
Bridge/Switch
Mode - Press 1.

If the Phone Adapter acts as the router
for your network, use the router/NAT
mode.

If your network already has a router, use
the bridge/switch mode.

Enable/Disable WAN
Access to the
Web-based Utility

7932 Enable -

Press 1.
Disable ­Press 0.

Use this setting to enable or disable WAN
access to the Web-based Utility. (This
Utility lets you configure the Phone
Adapter.)

Manual Reboot 732668 After you hear, “Option successful,” hang

up the phone. The Phone Adapter will
automatically reboot.

Interactive Voice Response Menu

Action Command Choices Description

* Follow these instructions to enter
the password.

• A, B, C, a, b, or c — press 2

2

.

• D, E, F, d, e, or f — press 3

3

.

• G, H, I, g, h, or i — press 4

4

.

• J, K, L, j, k, or l — press 5

5

.

• M, N, O, m, n, or o — press 6

6

.

• P, Q, R, S, o, q, r, or s — press 7

7

.

• T, U, V, t, u, or v — press 8

8

.

• W, X, Y, Z, w, x, y, or z — press 9

9

.

• All Other Characters — press 0

0

.

For example, to enter the
password

phone@321

by
keypad, press these keys:
746630321

. Then press the #

#

(pound) key to indicate that you
have finished entering the
password. To cancel your entry
and return to the main menu,
press *

*

(star).

For additional information or troubleshooting
help, refer to the User Guide, which is
available on the Linksys website. Contact
your Internet Telephony Service Provider for
further support.

Linksys Website

http://www.linksys.com or
http://www.linksys.com/support

3