LINKSYS MFEFX1, MFELX1 User Manual
USER GUIDE
100BASE-FX MiniGBIC
SFP Transceiver,
100BASE-LX MiniGBIC
SFP Transceiver
Model: MFEFX1, MFELX1
BUSINESS SERIES
Table of Contents
Chapter 1: Connect the Transceiver 2
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Installation Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Removal Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Appendix A: Specications 6
MFEFX1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
MFELX1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Appendix B: Switch Compatibility List 8
Appendix C: Warranty and Regulatory Information
Limited Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
FCC Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Safety Notices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Industry Canada (Canada) . . . . . . . . . . . . . . . . . . . . . . . . . 12
IC Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Règlement d’Industry Canada . . . . . . . . . . . . . . . . . . . . . . 12
EC Declaration of Conformity (Europe) . . . . . . . . . . . . . . . . . 12
Appendix D: Contact Information 21
Need to contact Linksys?. . . . . . . . . . . . . . . . . . . . . . . . . . 21
9
MiniGBIC SFP Transceivers
i
Chapter 1
Chapter 1: Connect the Transceiver
Introduction
Thank you for choosing the MiniGBIC SFP Modules. These Modules insert
into the MiniGBIC ports on Linksys switches. Each MiniGBIC SFP Module
is hot-swappable, meaning you can connect them even when the switch
is running.
Use the following directions for installing and removing either the
MFEFX1 or the MMFELX1.
WARNING: Optical SFPs use a small laser to generate the
fiber-optic signal. Because invisible laser radiation may be
emitted from the aperture of the port when no fiber cable is
connected, avoid exposure to laser radiation and do not stare
into open apertures. Keep the optical transmit and receive
ports covered whenever a cable is not connected to the port.
Installation Instructions
Insert the MiniGBIC SFP Module with the printed side up and the
1.
rubber port cap facing out.
Insert the Module
2
MiniGBIC SFP Transceivers
Connect the Transceiver
Remove the MiniGBIC SFP Module’s rubber port cap.
2.
Remove the Rubber Port Cap
Connect the fiber cable’s LC Connector to the MiniGBIC SFP Module’s
3.
port.
MiniGBIC SFP Transceivers
Connect the Fiber Cable
3
Chapter 1
Connect the other end of the cable to an SFP Module to verify that
4.
the fiber connection is complete.
Connected Fiber Cable
Removal Instructions
Press the fiber cable’s connector and pull to remove the fiber cable
1.
from the MiniGBIC SFP Module.
Remove the Fiber Cable
4
MiniGBIC SFP Transceivers
Connect the Transceiver
To remove the MiniGBIC SFP Module, begin by pulling the Module’s
2.
bail latch down.
Pull the Bail Latch Down
Remove the MiniGBIC SFP Module.
3.
MiniGBIC SFP Transceivers
Remove the Module
5
Loading...