Linear NAPRDW01 User Manual
NAPRDW01
PRODUCT DESCRIPTION
The NAPRDW01 is a battery powered recess mounted stationary transmitter
designed for use with NAPCO® GEM AND GEM-C systems. This transmitter can be
FEATURES
used in a variety of wireless security and remote control applications. Triggering the
RECESSED
DOOR/WINDOW
TRANSMITTER
Installation Instructions
transmitter with its built-in magnetic switch sends a digitally coded wireless signal to
its companion receiver.
The NAPRDW01 can send four different signal types: fault, restore, low battery,
and status. Receivers must be programmed to the transmitter’s code before system
testing and operation. Refer to the receiver’s instructions for details on programming.
In a typical installation, the magnet is mounted on a door or window and the transmitter
is mounted inside the frame. When the door or window is opened, the magnet moves
TRANSMITTER SCREW
MOUNT CAP
away from the transmitter and a fault signal is sent. When the door or window is
closed, the magnet returns next to the transmitter and a restore signal is sent.
Being supervised, about every 65 minutes the transmitter sends a status signal to
update the receiver. If the battery tests low, a low battery signal is included with any
RECESSED
TRANSMITTER
transmission. The transmitter is powered from one 3-Volt CR2 lithium battery (included).
USA & Canada (800) 421-1587 & (800) 392-0123
(760) 438-7000 - Toll Free FAX (800) 468-1340
www.linearcorp.com
Typically, no hardware is required to mount the transmitter. Two screws and a special
mounting cap are provided for mounting the transmitter in overhead applications.
INSTALLING OR CHANGING BATTERY DOOR INSTALLATION WINDOW INSTALLATION
1
SLOT
2
CAREFULLY SLIDE
OUT BOARD (NOTE
SLOT BOARD FITS IN)
OPEN THE TRANSMITTER
COVER BY TWISTING
A SMALL SCREWDRIVER
IN THE COVER SLOT
3
INSERT CR2
BATTERY
AS SHOWN
4
REVERSE STEPS TO REASSEMBLE
WARNING
DANGER OF EXPLOSION IF BATTERY IS
INSTALLED INCORRECTLY. REPLACE ONLY
WITH THE SAME OR EQUIVALENT TYPE
RECOMMENDED BY THE MANUFACTURER.
KEEP AWAY FROM SMALL CHILDREN. IF BATTERY IS
SWALLOWED, PROMPTLY SEE A DOCTOR. DO NOT TRY
TO RECHARGE THIS BATTERY. DISPOSAL OF USED
BATTERIES MUST BE MADE IN ACCORDANCE WITH THE
WASTE RECOVERY AND RECYCLING REGULATIONS IN
YOUR AREA.
DETERMINE A GOOD LOCATION TO
1
MOUNT TRANSMITTER IN THE TOP
OR TOP SIDE OF THE DOOR JAMB
(BE SURE IT'S OK TO DRILL A 2-1/2"
DEEP HOLE IN THAT LOCATION)
2
MARK THE JAMB LOCATION, THEN
MARK THE MATCHING LOCATION
ON THE DOOR
3
DRILL 11/16" HOLES:
2-1/2" DEEP FOR THE TRANSMITTER
1/2" DEEP FOR THE MAGNET
4
PRESS THE UNITS INTO THE HOLES
(IF MOUNTING ON TOP, SNAP ON THE
SCREW MOUNT CAP FIRST, THEN
SECURE WITH THE TWO SCREWS)
NOTE: TO REDUCE PHYSICAL SHOCK
TO THE TRANSMITTER, ALWAYS MOUNT
IT IN THE STATIONARY PART OF THE OPENING
NOTE: DO NOT USE IN METAL DOOR
FRAMES (IT WILL SHIELD THE SIGNAL)
DOOR JAMB
MAGNET
TRANSMITTER
SCREWS
(FOR TOP INSTALLS)
DOOR
DETERMINE A GOOD LOCATION TO
1
MOUNT TRANSMITTER IN THE WINDOW
FRAME (BE SURE IT'S OK TO DRILL
A 2-1/2" DEEP HOLE IN THAT LOCATION)
2
MARK THE FRAME LOCATION, THEN
MARK THE MATCHING LOCATION
ON THE WINDOW
3
DRILL 11/16" HOLES:
2-1/2" DEEP FOR THE TRANSMITTER
1/2" DEEP FOR THE MAGNET
4
PRESS THE UNITS INTO THE HOLES
(IF MOUNTING WITH THE TRANSMITTER
ON TOP, SNAP ON THE SCREW MOUNT
CAP FIRST, THEN SECURE WITH
THE TWO SCREWS)
NOTE: TO REDUCE PHYSICAL SHOCK
TO THE TRANSMITTER, ALWAYS MOUNT
IT IN THE STATIONARY PART OF THE OPENING
MOUNTING
SCREWS
RECESSED
MAGNET
NOTE: DO NOT USE IN METAL WINDOW
FRAMES (IT WILL SHIELD THE SIGNAL)
TRANSMITTER
WINDOW
WINDOW
FRAME
MAGNET
(IN WINDOW)
PROGRAMMING SPECIFICATIONS
WINDOW
TRANSMITTER
WINDOW
FRAME
(IN WINDOW)
SIGNAL
For a detail programming guide, the
instruction manual should be consulted for that
panel. The below guide should only be used as
a reference and not as a replacement for using
the panel programming
instructions.
1. Enter panel programming
2. Enter zone
3. Enter serial ID (auto-learn or
Manual)
To
MAGNET
Alpha Numeric Conversion
Auto - Learn
· hit “bypass”
· fault and restore the device
To Manual Learn
· Enter serial ID (listed on back
· Enter checksum (digit after the ¨:¨
on serial ID) For A-F use 0-5
(See Below)
4. Enter Point ¨1¨ for RDW
5. Push on/off to Save
A = *0 D = *3
B = *1 E = *4
C = *2 F = *5
Operating Temperature: 32° to 120° F (0° to 49° C)
Operating Relative Humidity: 5 to 95%, non-condensing
Operating Frequency: 319.5 MHz
Battery Type: 3-Volt CR2 Lithium Battery
California Only: This Perchlorate warning applies only to Manganese Dioxide Lithium cells
sold or distributed ONLY in California, USA. Perchlorate Material - special handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate
LINEAR LIMITED WARRANTY
This Linear product is warranted against defects in material and workmanship for twelve (12) months. This
warranty extends only to wholesale customers who buy direct from Linear or through Linear’s normal
distribution channels. Linear does not warrant this product to consumers. Consumers should inquire from their
selling dealer as to the nature of the dealer’s warranty, if any. There are no obligations or liabilities on the part
of Linear LLC for consequential damages arising out of or in connection with use or performance of this
product or other indirect damages with respect to loss of property, revenue, or profi t, or cost of removal,
installation, or reinstallation. All implied warranties, including implied warranties for merchantability and implied
warranties for fi tness, are valid only until the warranty expires. This Linear LLC Warranty is in lieu of all other
warranties express or implied.
All products returned for warranty service require a Return Product Authorization Number (RPA#). Contact Linear
Technical Services at 1-800-421-1587 for an RPA# and other impor tant details.
Linear radio controls provide a reliable communications link and fi ll an important need in portable wireless
signaling. However, there are some limitations which must be observed.
✴ For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 15
devices. As such, they have limited transmitter power and therefore limited range.
✴ A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals
that occur on or near their operating frequencies, regardless of code settings.
✴ Changes or modifi cations to the device may void FCC compliance.
✴ Infrequently used radio links should be tested regularly to protect against undetected interference or fault.
✴ A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or
dealer, and these facts should be communicated to the ultimate users.
This device complies with FCC Part 15 and Canada Rules and Regulations. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Copyright © 2013 Linear Corporation 187-1135 C
IMPORTANT !!!
Loading...