Linear MT9215S, MT9215 User Manual

1

5.2

6

.0

7

.6

3.0

1.3

1.3

0.5

Dia.

16.5

6.5

Detail A

mm

in

306.8

12.08

25.4

6.9

74.7

2.94

37.3

1.47

88.9

3.50

73.2

2.88

138.3

5.45

Detail A

See Detail A

See

See Detail B

INDOOR/OUTDOOR

FEED-THROUGH HOUSING MOUNTS

MT9215-24H

MT9215

MT9215S

I N STALLATION AND O P E RATING I N STRUCTIONS

MT9219

SAFETY PRECAUTIONS

Top

Bottom

he exclamation point within an equilateral triangle

T
is intended to alert the user to presence of impor­tant operating and maintenance (servicing) instruc­tions in the literature accompanying the appliance.

SECURITE

Le point d'exclamation à l'intérieur d'un triangle

quilatéral avertit l'utilisateur de la présence d'in-

é
structions importantes d'utilisation et de mainte­nance dans la documentation accompagnant l'ap­pareil.

SICHERHEITSVORKENHRUNGEN

Das Ausrufezeichen in dem gleichseitigen Dreieck
ist dazu da, den Benutzer auf wich-tige
Inbetriebnahme- und Instandhaltungs-vorschriften
hinzuweisen, die dem Gerät in Form einer
Broschüre beigelegt sind.

PRECAUCIONES DE SEGURIDAD

El símbolo de exclamación dentro de un triángulo
equilátero, se muestra con el objetivo de alertar al
ususario de que instrucciones de operación y man­tenimiento importantes acompañan al equipo.

1 UNPACKING

Unpack carefully.This is mechanical equipment and should be
handled with care.

The MT9215S has been designed specifically for the HS9480
series housings, while the MT9215-24H, MT9215 and MT9219
can be used with the HS9480, HS9483, and HS9488 series
camera housings.All mounts come fully assembled.

4 INSTALLATION

4.1 Installation of the MT9215-24H

1. Determine a secure wall mounting location.

ARNING: Do not mount in an inverted position.

W

2. Caution:

a. For a secure installation use six (6) bolts (not

included). The bolts should extend through the
mounting surface and be secured with nuts, lock
washers, and flat washers on the opposite side.

b. If studs are used, they should be anchored in

concrete or welded to a steel backer plate.

c. If the wall mount is attached to wood or to a blind

structure (with no access to the rear), make certain
that the mounting fasteners have a
out strength of 600 pounds.

WARNING: All mounts are designed to
support a load only in a vertical direction.
Mounts MUST be positioned as shown under
SPECIFICATIONS.

3. For ease of installation, locate the bottom mounting holes
first. Install the bolts (or studs) into the wall surface.

WARNING:The MT9215-24H must be mounted
with the slotted mounting holes of the wall plate
at the bottom.

minimum pull-

Check for the following items:

n Verify the unit model number.
n Instructions for Use.

If an item appears to have been damaged in shipment,replace it
properly in its carton and notify the shipper. If any items are
missing, notify Aigis Mechtronics.The shipping carton is the
safest container in which the unit may be transported. Save it
for possible future use.

2 SERVICE

er needs r

If the unit e
contact Aigis Mechtronics.

v

epair service, the customer should

3 DESCRIPTION

MT9215-24H 79-cm (30-in), MT9215 30-cm (12-in),
MT9215S 18-cm (7-in),
Feed-through Mounts.

The MT9215, MT9215S and the MT9219 are indoor/outdoor
mounts designed for fixed camera or camera housing
installations up to 9 kg (20 lb) rated load.The MT9215-24H is
designed for fixed camera or camera housings installation up
to 4.7 kg or (10.5 lbs). All models are made of lightweight
aluminum and feature welded construction, providing an
extremely rigid camera mount.

and MT9219 40-cm (15-in)

4. Reseat the MT9215-24H on the bolts (or studs) using the
bottom slotted holes, then locate the upper mounting
holes and drill into the wall surface.

5. Install the upper bolts (or studs) through the wall mount
and into the wall surface. Tighten upper and lower bolts
(or studs) securely.

The

Note:
10 mm (3/8 in).

6. To mount the camera or camera housing:
a. Mount camera with 2 - 1/4-20 bolts and lock

b. Mount housings with 2 - 1/4-20 bolts and

c. Lock mount head in position by using the supplied

2

minimumdiameter bolt (or stud) r

washers (not furnished) in the 2 holes of the
adjustable head.
and out through the hole near the base.

lockwashers (not furnished).Feed wires through
center hole and out through the hole near the base.

1/8-inch long-arm hex wrench to tighten screws.

Feed wires through the center hole

equir

ed is