Linear MT9212 User Manual

mm

in

1.0 0

8

26

1.0 4

25

INDOOR /OUTDOOR HOUSING MOUNTS

MT9210, MT9212,
MT9218, MT9219,
MT9223

I N S T A L L A T I O N A N D O P E R A T I N G I N S T R U C T I O N S

W W W

. A I G I S M E C H . C O M

SAFETY PRECAUTIONS

The exclamation point within an equilateral tri-

ngle is intended to alert the user to presence

a
of important operating and maintenance (ser-

icing) instructions in the literature accompany-

v
ing the appliance.

SECURITE

Le point d'exclamation à l'intérieur d'un triangle
équilatéral avertit l'utilisateur de la présence d'in­structions importantes d'utilisation et de mainte­nance dans la documentation accompagnant l'ap­pareil.

3 DESCRIPTION

MT9210 20-cm (8-in) Column Mount

T9212 30-cm (12-in) Wall Mount

M
MT9223 60-cm (24-in) Column Mount
MT9219 40-cm (15-in) J-Mount
MT9218 Corner Mount

his series of indoor/outdoor mounting equipment is

T
designed for fixed camera or camera housing installations up
to 9 kg (20 lb) rated load. All five models are made of
lightweight aluminum and feature welded construction
providing an extremely rigid camera mount. They have been
designed and styled for the HS948x Series camera housings.
All mounts come fully assembled.

SICHERHEITSVORKENHRUNGEN

Das Ausrufezeichen in dem gleichseitigen
Dreieck ist dazu da, den Benutzer auf wich-tige
Inbetriebnahme- und Instandhaltungs-vorschriften
hinzuweisen, die dem Gerät in Form einer
Broschüre beigelegt sind.

PRECAUCIONES DE SEGURIDAD

El símbolo de exclamación dentro de un triángu­lo equilátero, se muestra con el objetivo de aler­tar al ususario de que instrucciones de operación
y mantenimiento importantes acompañan al
equipo.

1 UNPACKING

Unpack carefully. This is mechanical equipment and should be
handled with care.

Check for the following items:

• Verify the unit model number.

• Instructions for Use.

If an item appears to have been damaged in shipment, replace
it properly in its carton and notify the shipper. If any items
are missing, notify Aigis Mechtronics.

The shipping carton is the safest container in which the unit
may be transported. Save it for possible future use.

2 SERVICE

If the unit ever needs repair service, the customer should
contact Aigis Mechtronics for authorization to return and
shipping instructions.

4 INSTALLATION

1. Determine a secure wall mounting location.

WARNING: All mounts are designed to support
a load only in a vertical direction. Mounts MUST be
positioned as shown under SPECIFICATIONS.

2. Cautions:
a. For a secure installation use four 8-mm (5/16-in)

diameter fasteners (not included). Use stainless
steel or zinc plated fasteners.

b. If bolts are used, they should extend through the

mounting surface and be secured with flat washers,
lock washers, and nuts on the opposite side. Each
bolt must have a minimum pull-out strength of 200
kg (450 lb).

c. If studs are used, they should be anchored in

concrete or welded to a steel backer plate. Each
stud must have a minimum pull out strength of 200
kg (450 lb).

d. If the wall mount is attached to wood or to a blind

structure (with no access to the rear), each fastener
must have a minimum pull-out strength of at least
200 kg (450 lb).

3. Locate the four holes or stud locations using the flange
as a template (four holes equally spaced on a 69.9 mm
(2-3/4 in bolt circle).

4. Install the mount using bolts or studs at least 8-mm
(5/16-in) in diameter.

5. To mount the camera or camera housing:
a. Mount camera with a 1/4-20 bolt and lock washer

(not furnished) in the center hole of the adjustable
head.

b. Mount housings with three 1/4-20 bolts and lock

washers (not furnished).

2