Linear 7441 Owner's Manual
74 41
CAMERA
MOUNTING
KIT
For Use with the
Model 7440 CCTV Camera
2055 Corte Del Nogal, Carlsbad, CA 92009, USA
760-438-7000
www.channelplus.com
SURFACE MOUNT
Linear LLC
800-999-5225
RECESS MOUNT
fax: 760-931-1340
PRODUCT DESCRIPTION
The Model 7441 Camera Mounting Kit is designed for use with
the Model 7440 Color CCTV Camera. The kit enhances the
installation options for the camera. Available in white (Model
7441W) and black (Model 7441B), the kit features two mounting
options for discrete, attractive CCTV camera installation.
The camera can be installed recessed in a wall or surface
mounted depending on the application. Installations that
require stealthy, low-profi le mounting should use the recessed
mounting option. The surface mounting option works well in
retrofi t installations and other mounting applications.
CAMERA MOUNTING KIT COMPONENTS INSTALL THE CAMERA IN THE BALL
SLIDE CAMERA
1
INTO BALL BASE
ALIGN SLOT WITH
TAB ON BALL TOP
CAMERA
BALL BASE
MAIN
BRACKET
RECESS
FLANGE
CAMERA
BALL TOP
DOME
COVER
TRIM
RING
SCREWS
1-1/2"
1/4"
SCREWS
1/2"
SCREWS
REMOVE
LENS CAP
2 3PUT THE BALL TOP
ON THE BALL BASE
CAMERA
BALL TOP
SURFACE MOUNTING RECESSED MOUNTING VIDEO CONNECTION
ATTACH THE MAIN BRACKET
1
WITH THREE 1-1/2" SCREWS
2
SLIDE DOME OVER
CAMERA BALL
SLOT ON DOME ALIGNS
WITH THE WIRE SLOT
3
INSTALL THREE 1/2" SCREWS
(WAIT UNTIL ALIGNMENT IS COMPLETE
BEFORE FULLY TIGHTENING)
FOR RECESSED WIRING
DRILL A 9/16" HOLE
FOR SURFACE WIRING
ROUTE WIRE IN SLOT
2
ATTACH THE MAIN BRACKET
TO THE RECESS FLANGE
WITH THREE 1/2"
SCREWS
DON'T TIGHTEN THE
SCREWS UNTIL AFTER
CAMERA ALIGNMENT
1
PLACE THE CAMERA
BALL INSIDE THE
RECESS FLANGE
RECESS FLANGE
FLANGE
WING
SCREWS
3-1/4" HOLE
IN DRYWALL
MAIN BRACKET
4
SNAP THE TRIM
RING ONTO THE
RECESS FLANGE
AFTER CAMERA
ALIGNMENT
POWER CONNECTION ALIGNMENT & TESTING SPECIFICATIONS
CONNECT THE CAMERA'S POWER INPUT
TO THE POWER SUPPLY TRANSFORMER
YELLOW CONNECTOR
VIDEO OUTPUT
FEMALE RCA
BLACK CONNECTOR
POWER INPUT
CAMERA
IN MOST INSTALLATIONS, THE POWER WIRE BETWEEN
THE TRANSFORMER AND THE CAMERA WILL NEED TO
BE EXTENDED
USE 18 AWG STRANDED UN-SHIELDED 2-CONDUCTOR
WIRE TO ADD TO THE TRANSFORMER'S WIRE LENGTH
(DO NOT CUT THE POWER WIRE ON THE CAMERA)
OBSERVE POLARITY WHEN SPLICING THE WIRE! THE
WHITE STRIPE ON THE TRANSFORMER'S WIRE IS
POSITIVE (+)
FEMALE MINI-JACK
TRANSFORMER
MALE MINI-JACK
VIDEO OUT
FROM CAMERA
12 VDC 500 mA
POWER SUPPLY
TRANSFORMER
PLUG THE
TRANSFORMER
INTO A 120 VAC
OUTLET
MAXIMUM RECOMMENDED
POWER WIRE LENGTH:
1500 FEET
ADJUST THE CAMERA
TO VIEW THE DESIRED AREA
LOCKING SCREWS (3)
SURFACE MOUNT
LOCKING SCREWS (3)
RECESS MOUNT
TIGHTEN THE LOCKING
SCREWS ON THE CAMERA
CASE AFTER ADJUSTING
THE CAMERA
ADJUST THE MONITOR
FOR THE BEST PICTURE
IMAGING ELEMENT: CCD
LENS: 2.1 mm, f 2.0
LUX: 0.5 minimum
RESOLUTION: 380 TV Lines
HORIZONTAL VIEWING ANGLE: 120°
VERTICAL VIEWING ANGLE: 100°
VIDEO OUTPUT: 1 volt peak-to-peak
VIDEO OUTPUT IMPEDANCE: 75Ω
POWER REQUIREMENTS: 12 VDC @ 90 mA
(Power supply included)
WIRING REQUIREMENTS: VIDEO: RG-59 or RG-6
(RG-6U recommended)
POWER: 18 AWG
2-conductor
Copyright © 2005 Linear LLC 9900623 A
3
INSTALL THE ASSEMBLY
INTO A 3-1/4" DRYWALL
HOLE THEN TIGHTEN
THE THREE FLANGE WING
SCREWS
IF FLANGE WINGS GET
STUCK, USE A FLAT BLADE
SCREWDRIVER IN THE
ACCESS SLOTS
TO FREE THEM
TRIM
RING
CONNECT THE CAMERA'S
VIDEO OUTPUT TO A MONITOR
OR TO A CHANNELPLUS
MODULATOR
MAXIMUM RECOMMENDED
VIDEO CABLE LENGTH:
RG-59 750-1000 FEET
RG-6 1000-1500 FEET
CAMERA
NOTE: FOR THE BEST PICTURE, RG-59U OR RG-6U COAX
IS RECOMMENDED. RG-6U IS MILITARY GRADE COAX
THAT HAS A BRAIDED SHIELD AND 20 AWG SOLID
COPPER CENTER CONDUCTOR
Linear LLC warrants this product to be free from defects in material and workmanship for 1
year. The time period will be measured using the date code labeled on the product. Linear
LLC is not responsible for damage to the product resulting from the buyer’s improper handling,
stocking or warehousing of the product. Any implied warranty arising from the sale of the
product including implied warranties of merchantability and fitness for purpose are limited.
Linear LLC shall not be responsible for any losses, damages or expenses, whether direct,
consequential, or incidental arising from the use or the inability to use the product. Some
states and countries do not allow limitations or how long an implied warranty lasts or the
exclusion or limitation or incidental or consequential damages, so the above exclusions may
not apply. The Linear LLC warranty gives specific legal rights in addition to other rights, which
may exist and vary from state to state and country to country.
The warranty is limited to repair or replacement of products returned, freight prepaid, to Linear
LLC, there is NO PROVISION FOR LABOR COST OR OTHER REIMBURSEMENTS OF
ANY KIND.
Linear LLC, at its option, will repair or replace the defective product. Replacements will be
made from B-Stock, if an exact replacement is not available, Linear LLC, at its option, will
select the nearest equivalent product. The user is responsible for freight charges to Linear LLC.
Linear LLC will return warranted repaired or replacements by UPS Ground or an equivalent
service. A customer may pay the additional costs for second-day or next-day service.
All products returned for warranty service require a Return Product Authorization Number
(RPA#). Contact Linear Technical Services at 1-800-999-5225 for an RPA# and other
important details.
LINEAR LIMITED WARRANTY
1. Failures due to product abuse, such as negligence, improper use, and electrical
surge including damage from lightning, water damage or other damage due to natural
disasters are not covered by the warranty. The most common form of product abuse is
surge damage caused by lightning.
2. The warranty shall also be voided by any tampering with the date code, labels or other
markings on the product.
3. Products that are damaged in transit to Linear LLC due to improper packaging or by the
carrier (shipping company) will not be covered under the warranty. If the product was
damaged or lost by the carrier, it is the sender’s responsibility to create a claim against
the carrier.
4. The user is responsible for all labor costs associated with removing, reinstalling and
returning the product to Linear LLC.
VIDEO OUT
FROM
CAMERA
YELLOW CONNECTOR
VIDEO OUTPUT
FEMALE RCA
WIRE ON TOP
EDGE OF CAMERA
INSTALL TWO 1/4"
SCREWS
MALE RCA
TO FEMALE
TYPE-F ADAPTER
RG-59 OR RG-6 COAX TO VIDEO
MONITOR OR CHANNELPLUS
MODULATOR
USE THE SECOND RCA-TO-F
ADAPTER AT THE OTHER
END OF THE COAX IF REQUIRED
BLACK CONNECTOR
POWER INPUT
FEMALE MINI-JACK
ROUTE
WIRE
THROUGH
BALL BASE
CAMERA
BALL BASE
MALE
F-CONNECTOR
Loading...