Life Fitness 909101 ST User Manual

909101 ST LEG CURL/EXTENSION
ASSEMBLY INSTRUCTIONS
Part # 6705201 Revision: 01/9/981
IMPORTANT NOTES
WELCOME TO THE WORLD OF Serious steel!
Please note:
* Thank you for purchasing the Parabody 909101 ST Leg Curl/Extension. Please read these instructions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function.
* We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy water. Touch-up paint can be purchased from your Parabody customer service representative at (800) 328-9714.
There is a risk assumed by individuals who use this type of equipment. To minimize risk, please follow these rules:
1. Inspect equipment daily . Tighten all loose connections and replace worn parts immediately. Failure to do so may result in serious injury.
2. Do not allow minors or children to play on or around this equipment.
3. Exercise with care to avoid injury .
4. If unsure of proper use of equipment, call your local Parabody distributor or call the Parabody customer service department at (800) 328-9714.
T ools Required for Assembly
* Rubber mallet or hammer * 3/4” wrench * 9/16” wrench * Ratchet with 3/4” and 9/16” sockets * 5/32” Allen wrench * Adjustable wrench * T ape measure
Bolt Length Ruler
NOTE: BOL T LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE BOLT.
BOL T LENGTH RULER:
1/2 1/2 1/2 1/2 1/2 1/2
0
1
BOLT LENGTH
2
345
2
6
PARTS LIST
KEY
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28
PART #
6697803 6662303 6662203 6705501 6523401 6699302 6700303 6698003 6698903 6698603 6698303 6625502
6693502 66373XX 66370XX
6704101
6704201
6695501
6284501
6714601
3116101
3116201
6695401
3108901
6382301
3108002
6166701
3116001
DESCRIPTION
TOWER
LEG EXT HANDLE LEFT
LEG EXT HANDLE RIGHT
4 OD X 7" ROLLER PAD
3/4 OD X 72-3/8" GUIDE ROD
PAD SLEEVE
BENCH FRAME
LOWER CROSS SUPPORT
LEG PEDESTAL TOWER BRACE
UPPER CROSS SUPPORT
PAD SUPPORT RIGHT
PAD SUPPORT LEFT
BACK PAD
SEAT PAD
FRONT SHROUD
REAR SHROUD
3/4 DIA X 18-1/4" SHAFT
20 HOLE WEIGHT STACK SHAFT
HEAD PLATE 4-1/2" PULLEY 3-1/2" PULLEY
175-1/2" CABLE
2” OD PLASTIC WASHER
WEIGHT PLATE BUSHING 10 CT
WEIGHT STACK CUSHION
2-7/8" L BRACKET
1-1/4” SQ. RUBBER BUMPER
QTY
1 1 1 6 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 3 2 1 8 4 2 1 1
KEY
29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55
PART #
6140701 3102407 6628302 3202114 3102917 3102910 3102915 3102922 3102933 3102909 3202401 3102502 3102501 3114502 3102801 3102802 6406401 6466901 6412001 6214401 3105401 6020601 6695001 6703801 6703901 6214501 3104901
DESCRIPTION
1 X 1" GLIDE
3 X 2" END CAP
1/8 X 2 X 8" PLATE
1/2 X 6" BOLT 1/2 X 4" BOLT
1/2 X 3" BOLT 3/8 X 3-1/4" BOLT 3/8 X 2-3/4" BOLT
3/8 X 2" BOLT
3/8 X 1" BOLT
3/8 X 1" BTN HEAD CAP SCREW
1/2" WASHER
3/8" WASHER
3/8" LOCKWASHER
1/2" LOCK NUT 3/8" LOCK NUT
HINGE TAB 1/2" SPRING PIN 3/8" SPRING PIN
SELECTOR PIN
STARLOCK COLLAR
1/2" FLANGE BEARING
3/4" DIA TAPPED SHAFT
WEIGHT STACK LABEL LBS.
WEIGHT STACK LABEL KGS.
WEIGHT PLATES
3/4” FLANGE BEARINGS
QTY
2 2 1 1 6 4 2 4 5 7
5 10 15
3 11 10
2
1
2
1
6
2
1
1
1 20
2
LEG CURLLEG EXTENSION
3
34 1/2 X 3”
40
1
43
11
40
43
40
33 1/2 X 4”
FIGURE 1
43
40
1/2 X 4” 33
1/2 X 3” 34
8
43
7
STEP 1:
LOOSELY assemble LOWER CROSS SUPPORT (8) to the TOWER (1) and BENCH FRAME (7) using four 1/2 X 4” BOLTS (33),
four 1/2” WASHERS (40) and four 1/2” LOCK NUTS (43). See FIGURE 1.
LOOSELY assemble UPPER CROSS SUPPORT (11) to the TOWER (1) and BENCH FRAME (7) using four 1/2 X 3” BOLTS (34),
four 1/2” WASHERS (40) and four 1/2” LOCK NUTS (43). See FIGURE 1.
• SECURELY TIGHTEN ALL THE CONNECTIONS MADE UP TO THIS POINT.
1/2 1/2 1/2 1/2 1/2 1/2
0
1
2
345
4
6
45
2
44
3
45
7
41
35 3/8 X 3-1/4”
FIGURE 2
STEP 2:
SECURELY assemble the LEFT (2) and RIGHT (3) LEG EXT. HANDLES to the BENCH FRAME (7) using two 3/8 X 3-1/4”
BOLTS (35), four 3/8” WASHERS (41), and two 3/8” LOCK NUTS (44). See FIGURE 2.
• Slide two HINGE TABS (45) onto the BENCH FRAME (7) as shown in FIGURE 2.
STEP 3:
SECURELY assemble one 1/8 X 2 X 8” PLATE (31)
to the SEAT PAD (15) using two 3/8 X 1” BOLTS (38) and two 3/8” WASHERS (41). See FIGURE 3.
15
FIGURE 3
5
41
31
3/8 X 1” 38
Loading...
+ 10 hidden pages