Liebherr EWTNes 2956 User Manual

Page 1
Installation
41
On/Off SuperFrost Alarm
64
LightOn/Off
Zone UpUpDown
0
Instructions
For wine cooler with
NoFrost freezer compartment and
Side-By-Side Units
with IceMaker
Instructions
de montage
Armoire de mise en température des vins avec congélateur NoFrost et les
2-6
4-8
6-12
4
appareils côte à côte
avec IceMaker
2-6
4-8
6-12
3
Instrucciones
de instalación
2-6
4-8
6-12
2
2-6
4-8
6-12
1
Armario de acondicionamiento de
vinos con congelador NoFrost y
unidades lado a lado
con IceMaker
WF1051 / EWTNes 2956
7082 410-00 3405
Page 2
I
MPORTANT
PLEASE READ AND FOLLOW THESE INSTRUCTIONS
These instructions contain Warning and Caution statements. This information is important for safe and efficient installation.
Always read and follow all Warning and Caution statements!
WARNING
!
States a hazard that may cause serious injury or death if precautions are not followed.
CAUTION
!
Signals a situation where minor injury of product damage may occur if you do not follow instructions.
IMPORTANT
This highlights information that is especially relevant to a problem-free installation.
Make sure incoming voltage is the same as the unit rating.
To reduce the risk of fire, electric shock, or personal injury, installation work and electrical wiring must be done by a qualified electrician in accordance with all applicable codes and standards, including fire-rated construction.
A delight in freshness
ii
WF1051 / EWTNes 2956
Page 3
TO THE INSTALLER
It is very important that the guidelines and instructions are followed in the manual to ensure proper installation and operation of the unit. The Installation Guidelines section contains important information for making sure the installation is correct. Read and understand all the information in Installation Guidelines, and in this manual before the unit is installed.
I
MPORTANT
WF1051 / EWTNes 2956
A delight in freshness
1
Page 4
T
ABLE
OF
Contents Page
Installation Guidelines ................................................................................. 3
Area Requirements ............................................................................... 3
Electrical Requirement .......................................................................... 3
Customer’s Responsibility .................................................................... 3
Blocking For Safety ............................................................................... 3
Unit Venting ........................................................................................... 3
Planning Information ................................................................................... 4
Cabinet Opening Dimensions ............................................................... 4
Reversing Door Hinges ............................................................................... 9
Door Opening Angle ........................................................................... 12
Installation ................................................................................................. 13
Blocking For Safety ................................................................................... 16
IceMaker .................................................................................................... 17
Water Connection ............................................................................... 17
Connection to the Water Supply ......................................................... 18
Side-By-Side Installation ........................................................................... 20
C
ONTENTS
A delight in freshness
2
WF1051 / EWTNes 2956
Page 5
I
NSTALLATION
G
UIDELINES
Area Requirements
Verify the following:
• Floors can support refrigerator’s weight plus approximately 1200 pounds (544 kg) of food weight.
• Finished kitchen floor height has to be level. Appliance must be shimmed to the floor level if the floor heights are not equal to make sure air vents are not obstructed.
• Remove anything attached to rear or side walls that can obstruct refrigerator opening.
• Cutout dimensions are accurate.
• Electrical outlet is in correct location.
Do not install this unit next to any other refrigerator or freezer except another Liebherr model. Liebherr models are designed to allow side-by-side installation. They are equipped with a heating element to eliminate condensation when units are installed side by side. Installing this unit next to any other refrigerator or freezer can cause condensation or cause damage to the Liebherr unit.
WARNING
!
ELECTROCUTION HAZARD
Electrical Grounding Required. This appliance is equipped with a three-prong (grounding) polarized plug for your protection against possible shock hazards.
DO NOT remove the round grounding
prong from the plug.
DO NOT use a two-prong grounding
adapter.
DO NOT use an extension cord to
connect power to the unit.
Customer’s Responsibility
A 115 Volt, 60 Hz, 15 Amp (20 Amp for side-by­side installation) fused electrical supply is required. We recommend using a dedicated circuit for this appliance to prevent electrical overload. Follow the National Electrical Code and local codes and ordinances when installing the receptacle.
Blocking For Safety
The anti-tip brackets must be installed to prevent the unit from tipping after it is installed. Refer to Blocking For Safety.
Electrical Requirement
If codes require a separate grounding circuit to be used, have a qualified electrician install the circuit.
WARNING
!
Do not ground to a gas pipe. Check with a qualified electrician if you are not sure the appliance is properly grounded. Do not have a fuse in the neutral or grounding circuit.
WARNING
!
ELECTRICAL SHOCK HAZARD
• Electrically ground refrigerator.
• Do not use an extension cord.
• Failure to follow these instructions could result in fire or electrical shock.
Unit Venting
DO NOT restrict the air flow. Air flow must be provided for the unit to operate. The factory air vents provide 31 square inches (200 cm²) of air flow per unit. If you are replacing the factory air vents with an overlay, the air flow must be the same or greater than the factory air vents.
WF1051 / EWTNes 2956
A delight in freshness
3
Page 6
P
LANNING
I
NFORMATION
Cabinet Opening Dimensions -
Figure 1
Allow units to open a minimum of 90° to prevent problems removing drawers. With the door opening 90°, you may have to move drawers slightly to clear the door interior.
Refer to the minimum door clearances in the Pre­Installation Specifications chart.
• Allow for a minimum 3-3/4" (95 mm) filler, for corner installations, so the door can open to 90°. If you’re using raised panels, consider using a wider filler.
IMPORTANT
Refer to the full scale illustrations at the end of this section for specifics on door openings and filler size alternatives.
"
"
3"
(76mm)
"
"
"
Figure 1
"
"
A delight in freshness
4
WF1051 / EWTNes 2956
Page 7
WF1051 - Figure 2
P
LANNING
I
NFORMATION
WF1051 / EWTNes 2956
Figure 2
A delight in freshness
5
Page 8
P
LANNING
Side-By-Side WF1051 and RB1400 - Figure 3
I
NFORMATION
Figure 3
A delight in freshness
6
WF1051 / EWTNes 2956
Page 9
P
The factory setting for the door to swing open is 130°. Use this illustration to ensure other cabinets or counters do not interfere with the door opening.
LANNING
I
NFORMATION
130°
WF1051 / EWTNes 2956
A delight in freshness
7
Page 10
P
LANNING
The optional setting for the door to swing open is 90°. Use this illustration to ensure other cabinets or counters do not interfere with the door opening.
I
NFORMATION
90°
A delight in freshness
8
WF1051 / EWTNes 2956
Page 11
R
14
A
A
Y
X
W
W
X
Y
17
8
7
2
5
8
7
9
2.
2.
5.
5.
4.
4.
3.
1.
Fig.A BGENes
EVERSING
The door hinges can be changed from one side to the other if required.
1. Figure 4: Top: Unscrew the hinge pin (2) and remove the screw (5).
2. Swivel out the door at the top, ensuring that you do not lose the stop (7) and bushing (8); lift off the door and place it on the floor. Unscrew the handle from the upper door and pull out the cover caps (A). Then screw the handle on the opposite side of the upper door and place the plugs (Y) in the open screw holes.
3. Center: Pull out the hinge pin (9) with its washer.
4. Swivel out the lower door, lift it out and place it on the floor. Take care not to lose the stop (7) and washers (8). Unscrew the handle from the lower door and pull out the plugs (A). Then screw the handle on the opposite side of the lower door and place the plugs (Y) in the open screw holes.
5. Unscrew all the door fittings (14, 17) and remove plugs (W, X).
D
OOR
Figure 4
H
INGES
WF1051 / EWTNes 2956
A delight in freshness
9
Page 12
R
EVERSING
D
OOR
H
INGES
6. Figure 5: Unscrew the lower hinge (13).
- Remove the washer, stops and bushing (14, 7, 8).
- Remove screw (Q).
- Transfer hinge pin (2) to the opposite side.
- Transfer screw (Q) to the opposite side.
- Turn the stop (7) through 180° and position bushing (8) and washer as shown in the detailed drawing. The flat side of the stop must face forwards.
- Screw on hinge (13) on the new hinge side.
7. Install the door fittings as shown in Figure 5.
Insert the plugs (X) as shown in the detailed drawing. Move plug (W) to the opposite side of the lower door.
8. Unscrew the center hinge (10) and cover (11),
pull them off to the side and after turning them through 180°, slide them on again on the opposite side and secure them.
9. Place the lower door on the hinge pin (2) at the
bottom.
- Swivel in the door.
- Pay special attention to the bushing (12) in the center hinge (10).
- Insert the hinge pin (9).
Figure 5
A delight in freshness
10
WF1051 / EWTNes 2956
Page 13
R
EVERSING
D
OOR
H
INGES
10. Figure 6: Lift up cover (3) on handle side, push outward; lift up cover (1) on hinge side and pull off.
11. Unscrew mounting plate (21): first mounting screw (20), then inner retaining screw (25).
- Unscrew hinge (4): first remove the mounting screw (20), then retaining screws (25). Fit hinge (4) to opposite side: for easy assembly, fit hinge from above and first tighten with the upper retaining screw (25) M5, then screw (25) and finally mounting screw M4 (20).
- Turn mounting plate (21) through 180° and screw tight again on the new handle side: first retaining screw (25), then mounting screw (20).
12. Transfer hinge pin and screw to the respective
opposite side of the hinge (4), but do not insert them in the hole or fasten them now.
13. On the upper door, install the door fittings as
shown in Figure 6. Insert the plugs (X) as shown in the detailed drawing. Move plug (W) to the opposite side of the door.
14. Place the upper door on the center hinge, fit the
bushing (8), stop (7) and washer on the door, swivel in the door at the top and insert and secure the hinge pin (2) from above through the hinge and stop. Insert screw (6) for fixing the opening angle to 130°.
Check for proper alignment of all doors. Adjust them if necessary using the slots on the hinge.
WF1051 / EWTNes 2956
W
Figure 6
A delight in freshness
11
Page 14
R
EVERSING
D
OOR
H
Door Opening Angle - Figures 7, 8
The appliance is delivered with a door opening angle of 130°.
If the angle is to be decreased to 90°, proceed as follows:
Insert attached screw (6) in the upper hinge as
shown in Figure 7.
Insert eccentric (Z) in the lower hinge as shown in Figure 8. Fix the eccentric with screw (V). The eccentric pin must point away from the hinge pin.
INGES
6
Figure 7
Figure 8
Fig.D1-2 BGENes
Q
Z
V
Fig.D1-2 BGENes
A delight in freshness
12
WF1051 / EWTNes 2956
Page 15
I
NSTALLATION
Only install the winecooler/freezer in a stable kitchen cabinet that has been properly aligned.
- Mount and fix the handles, depending on your model and choice.
Unpacking
Unpack the installation kit and check with the pro­vided parts list if all parts are included. The part numbers given in the parts list are identical to the numbers in the respective fi gures.
For installation you will need the following tools:
Included:
- Star Key Torx® 15
- Star Key Torx® 20
- Star Key Torx® 25
- Socket Wrench 8 mm
- Open-end Wrench 10 mm
Not in package:
- Phillips (star) screwdriver
- Level
- Ruler
1.
2.
8
2 1
3
4
6 4 5
3.
6 4
4.
6
6 4
5
446
5
5
Figure 16: Installation with Ventilation Grille Set:
1. Screw the installation frame at the top (1) onto the appliance (2).
2. Place the ventilation grille (3) on this, align it in the center and secure at the front from underneath.
3. Slide brackets (4) onto the side installation frames (5) from above and below.
4. Using the frame (5), screw the brackets onto the side wall*.
5. Slide the side installation frames (5) upwards until they are in contact with the underside of the ventilation grille.
6. Secure the side frames with the adhesive section (7) to prevent them from sliding down. Remove the protective film and affix the adhesive sections over the upper brackets on the handle and hinge sides.
5.
7
6.
7
7
6.
7
WF1051 / EWTNes 2956
Fig.E BGENes
Figure 16
A delight in freshness
13
Page 16
I
NSTALLATION
- Figure 17: Connect the appliance to the
main power supply.
- If the appliance is equipped with an IceMaker, establish the connection for the water supply. See “IceMaker, Water Connection”.
1
1. 2.
1. Carefully slide the appliance into the cabinet until the ventilation grille touches the surrounding kitchen cabinet.
2. Align the appliance until it is parallel with the sur­rounding kitchen cabinet. Use the open- end wrench 10 mm (3) to adjust the feet at the front.
2 3
2
2 3
8 spanner
3
10 spanner
Figure 17
Turn clockwise for up and counterclock-wise for down. For the rear use the adjusting
3.
bolt (2). Turn clockwise for down and counter­clockwise for up. Maximum adjustment: 19/64" (15 mm).
1
2
3. Figure 18: Align the appliance at the side
with the cabinet side panel and attach it with screws (1).
- Cover the screws with cover caps (2).
4. Fit the ventilation grille at the bottom [(3) if the door is hinged on the left, (4) if it is on the right]: Secure the ventilation grille so that it touches the floor and then adjust it using the
5
4.
5
3
5
4
5
slots.
Figure 18
A delight in freshness
14
WF1051 / EWTNes 2956
Page 17
I
NSTALLATION
The following ventilation cross-section and distances must be observed:
- There must be a ventilation space of at least 31 square inches (200 cm²) per appliance in the cabinet plinth and under the cabinet top panel.
- The depth of the ventilation duct at the rear of the cabinet must be at least 1­1/2" (38 mm).
Alternatively:
1. For built-in appliances without ventilation grilles and only with an installation frame, ventilation must take place through the ventilation duct at the rear of the cabinet.
Built-in appliances with an installation frame:
Figure 19:
- Screw the complete installation frame (2)
to the appliance.
1 1/2”
(38mm)
At least 31 square inches (200cm )
/4
)
3
m
0
m
2
7
2
5
(
1.
2
1
2
2. Built-in appliances with a wooden ventilation grille:
Figure 20: Cut out the wooden trim for use
as a ventilation grille using the enclosed template.
- The required ventilation cross-section must be at least 31 square inches (200 cm²) when a single appliance is installed, which corresponds to template “small” (If you install two appliances side-byside, the cross-section must be at least 62 square inches, (400 cm²), which corresponds to template “double-size;” for more information see “Side-by-Side Installation”).
Remove the attachment bracket (2) from
the installation frame and screw it to the appliance (1) from underneath. Place the wooden ventilation grille (5) on the appliance, align it in the center and secure it from the rear using the attachment bracket (2).
Figure 19
2
1
(609.6 mm)
5
24"
1/2"
(13 mm)
WF1051 / EWTNes 2956
A delight in freshness
15
3-11/16"
(93,7 mm)
Figure 20
Page 18
B
LOCKING
F
OR
S
AFETY
Figure 21: Secure the appliance in place so it does
not tip forward when the fully stocked door is opened.
1. Measure the distance from the floor to the upper edge of the unit.
2. Locate and mark two wall studs (1) against the wall where the appliance will be located. The space between the unit top and the bottom of the brackets must not be more than 1/4" (6.4 mm).
3. Make sure the screws (2) extend a minimum of 1" (25.4 mm) into each of the wall studs.
4. Make sure the anti-tip brackets (3) extend at least 3" (76.2 mm) over the unit and are securely in place.
IMPORTANT
The anti-tip brackets can be installed in either direction or closer together. Always position the anti-tip brackets as wide apart as possible, but make sure they are anchored to two studs.
5. Using the adjustable roller base, raise the unit until it makes contact with the brackets. Make sure the front levelers are firmly on the floor to prevent the appliance from tipping forward.
IMPORTANT
If your unit is positioned in between the wall studs, a board can be secured to the wall. Make sure the board is secured to the studs with screws that will penetrate into the studs a minimum of 1" (25.4 mm). The board should be a minimum of 1" x 6" (25.4 mm x
152.4 mm) and long enough to secure both ends to the wall studs.
3
1
2
min 3"
Fig.R BGENes
Figure 21
A delight in freshness
16
WF1051 / EWTNes 2956
Page 19
I
CE
M
AKER
Water Connection - Figure 22
Please read the first three points of the safety instructions and warnings before connecting the appliance to the main water supply.
• The water pressure must be between 21.8-
87.0 psi (1.5-6 bar).
Use a 1/4" OD copper line to connect the water
supply to the solenoid valve. Allow extra length to the water supply line to provide slack for easy removal and to prevent the line from kinking.
This is not supplied with the appliance (Figure 22).
• A shut-off valve, such as the saddle valve illustration here, must be installed between the hose line and the main water supply so the water supply can be stopped if necessary.
Figure 22
Do not install the shut-off valve behind the appliance.
• If you have hard water, we recommend you install a water softener. Also, a filter must be installed if the water contains solids such as sand.
• All equipment and devices used to supply the water to the appliance must comply with the current regulations for your geographical area.
WF1051 / EWTNes 2956
A delight in freshness
17
Page 20
I
CE
M
AKER
Connection to the Water Supply
- Figures 23, 24
1. Install the shut-off valve, water filter and automatic shut-off device as required.
Note
The solenoid valve is located at the rear of your unit.
2. Place a 1/4" OD copper tubing between the shut-off valve and solenoid valve. Make sure there is approximately 30" (70 cm) of excess tubing behind the unit for easy connection.
IMPORTANT
The solenoid valve has a Metric R3/4 male connection. A R3/4(metric) to a 1/4" OD adapter and cable clip are supplied with the icemaker.
Figure 24: Remove the cover cap (4) from
the solenoid valve (1). Install the connection bracket (2) with sealing ring (6) on the solenoid valve (1). Attach the copper tube to the connection bracket (2). Secure the copper tube (3) to the appliance using the cable clip (5).
3. Open the shut-off valve for the water supply and check the entire water system for leaks. Before the appliance is used for the first time a licensed plumber should bleed air from the system.
4. Insert the electrical plug for the combined winecooler/freezer into the electrical outlet (Figure 23).
5. Move the combined winecooler-freezer into final position in the room.
Figure 23
A delight in freshness
18
WF1051 / EWTNes 2956
Page 21
I
CE
1
4
M
AKER
WF1051 / EWTNes 2956
1
6
2
3
5
5
Figure 24
A delight in freshness
19
Page 22
S
IDE
-B
Y
-S
IDE
I
NSTALLATION
Unpacking
Unpack the side by side installation kit and check with the provided parts list if all parts are included. The part numbers given in the parts list are identical to the numbers in the respective fi gures.
For installation you will need the following tools:
Included:
- Star Key Torx® 15
- Star Key Torx® 20
- Star Key Torx® 25
- Socket Wrench 8 mm
- Open-end Wrench 10 mm
Not in package:
- Phillips (star) screwdriver
- Level
- Ruler
Figure 25: To install the WF1051 and RB1400 appliances side-by-side, proceed as follows:
- Always place the WF1051 and RB1400 with the hinges on the left-hand side (looking from the front).
Installation with SBS Ventilation Grille Set:
1. Affix the spacer (1) on the side wall of the
appliance – remove the protective film.
2. Push the appliances together,
- align them parallel to each other.
3. Use a level on the top to align them to the same height:
4. Use the open-end wrench 10 mm (3) to adjust the feet at the front of the roller base. Turn clockwise for up and counterclockwise for down. For the rear, turn the adjusting bolt (2) clockwise down and counterclockwise up.
Figure 25
A delight in freshness
20
4.
WF1051 / EWTNes 2956
Page 23
S
IDE
-B
Y
-S
IDE
I
NSTALLATION
5. Figure 26: Secure the installation frame (3) at the top to the appliances with screws (2).
- Align the appliance at the front bottom.
- Use the predrilled holes to align the installa-
tion frame (2).
- First mount the installation (3) frame with 4 screws (2) to one appliance, then align the other appliance with the predrilled holes to the installation frame (3) and secure it with the screws (2).
6. Figure 26: Position the attachment brackets (6)
at the rear of the appliances at the top and bottom. Slide the upper attachment bracket upwards as far as possible. Secure it at the side using the screws provided (5). Do not overtighten!
5.
2 3
6.
6.
Figure 26
ca. 210
6
5
5
6
WF1051 / EWTNes 2956
A delight in freshness
21
Page 24
S
IDE
7. Figure 27: Push the long carriage bolt M5x260 (7)
through the leveling wheels as shown. Fit in a washer (8). Screw on the wing nut (9) and tighten it manually. Do not overtighten.
8. Turn the adjustable roller base up. Otherwise you will damage the floor when you push in the appli­ances.
9. Secure the ventilation grille (10) to the appliance with screws (11).
Push in the sealing strip (4) as shown.
-B
Y
10
-S
IDE
I
NSTALLATION
9.
4
11
9 8 7
7.
4
10 spanner
Figure 27
A delight in freshness
22
7
8.
2
8 spanner
3
WF1051 / EWTNes 2956
Page 25
S
IDE
-B
Y
-S
IDE
I
NSTALLATION
10. Figure 28: Slide the side installation frames (15) upward until they are in contact with the underside of the ventilation grille, Figure 28.
11. Secure the side frames with the adhesive section (17) to prevent them from sliding down. Remove the protective film and place the adhesive sections over the upper brackets.
12. Figure 29: Install anti-tip brackets for each appliance. Refer to “Blocking For Safety.”
10.
17
15
17
11.
15
11. 17
Fig.Q BGENes
Figure 28
3
1
2
min 3"
Fig.R BGENes
Figure 29
WF1051 / EWTNes 2956
A delight in freshness
23
Page 26
S
IDE
13. Figure 30, 31: Connect the appliances:
- to the main power supply and
- to the water supply if the appliance is equipped with an IceMaker. See “IceMaker, Water Connection,” Figure 30.
14. Carefully slide the connected appliances into the recess until the ventilation grille touches the top, Figure 31.
-B
Y
-S
IDE
I
NSTALLATION
15. Align the appliances by using only the outer leveling wheels at the front (3) and rear (2).
13 .
Figure 30
14 .
10 spanner
Figure 31
A delight in freshness
24
15 .
2
8 spanner
3
Fig.S BGENes
WF1051 / EWTNes 2956
Page 27
S
IDE
16. Figure 32: Attach the aligned combination to the
surrounding kitchen cabinet. Secure it through the side frames using the screws (20) provided.
- Cover the screws with cover caps (21).
17. Now adjust the center adjustable roller bases (22) so that they make slight contact with the floor.
18. Install the lower ventilation grille (23): Secure the ventilation grille so that it touches the floor and adjust it using the slots. Do not overtighten!
-B
Y
-S
IDE
I
NSTALLATION
20
22
16.
17.
18.
10 spanner
24
2
21
8 spanner
3
WF1051 / EWTNes 2956
24
23
24
Figure 32
A delight in freshness
25
24
Fig.U BGENes
Page 28
S
IDE
-B
Y
-S
IDE
I
NSTALLATION
1. For built-in appliances without ventilation grilles and only with installation frame (2),
ventilation must take place through the ventilation duct at the rear of the cabinet. Ensure that the ventilation cross-section is at least 31 square inches (200 cm²) per appliance. At least 62 square inches (400 cm²) for side­by-side installation of two appliances. Built-in appliances with an installation frame:
- Figure 33: Screw the installation frame (2)
to the appliance through the attachment brackets.
1 1/2”
(38mm)
At least 31 square inches (200cm )
/4
)
3
m
0
2
m
7
2
5
(
/4
)
3
m
0
2
m
7
2
5
(
2
per unit
1.
2
6
Figure 33
A delight in freshness
26
WF1051 / EWTNes 2956
Page 29
S
IDE
Built-in appliances with a wooden ventilation grille:
2. Figure 34: Cut out the wooden trim for use as a
ventilation grille using the attached template.
- The required ventilation cross-section must be at least 62 square inches (400 cm²) for side-by-side installation of two appliances, which corresponds to the attached template “double-size.”
-B
Y
2.
-S
IDE
- Remove the attachment brackets from the
- Place the wooden ventilation grille (5) on the
I
NSTALLATION
installation frame (2) and screw them to the appliance from underneath.
appliance, align it in the center and secure it from the rear using the attachment brackets.
WF1051 / EWTNes 2956
3-11/16"
(93,7 mm)
Figure 34
A delight in freshness
27
48"
(1219,2 mm)
5
1/2"
(13 mm)
Loading...