LG LDP6797ST Installation Guide
INSTALLATION
11INSTALLATION
Installation Parts and Tools
Parts not Provided
Electrical cable Water supply tube Fittings for tube Coupler Teon™ tape
Air gap Wire nuts for
16-gauge wiring
Tools Needed
Hose clamp ⅞" UL approved
strain relief
Electrical tape
ENGLISH
Flat-blade
screwdriver
Safety glasses Adjustable wrench Tape measure Utility knife Level
Tubing cutter Nipper Pliers Wire stripper ¼" Square
Phillips
screwdriver
Hole saw
min. 2½" bit
Electrical drill Gloves
drive wrench
12 INSTALLATION
Installation Overview
Preparing Cabinet Opening
Preparing Electrical Wiring
Preparing Water Supply Connection
Preparing the Dishwasher
Removing Lower Cover
Sliding the Dishwasher into Cabinet
Leveling the Dishwasher
Securing the Dishwasher to Countertop
Connecting the Drain Hose
Connecting Water Supply
Connecting Power
Final Check
Product Dimensions
Back view Side view
3
23 /4" (603 mm)
5 13
26 /8 - 26 /16" (676 - 681 mm)
5
24 /8" (625 mm)
5
1
4 /2"
(115 mm)
3
9 /8"
(238 mm)
11
4 /16"
(119 mm)
1
/4"
5
(134 mm)
33 /16"
(846 mm)
1
4 /2"
(115 mm)
15
2 /16" (75 mm)
3
4 /4" (120 mm)
3
20 /16" (512 mm)
Water supply hose, drain hose and electric cable should be passed
through this area.
33 /8"
(854 mm)
NOTE
• For easiest installation, see marked areas above for water and electrical clearances in base of dishwasher.
Product Specications
The appearance and specications listed in this manual may vary due to constant product improvements.
Electrical requirement 120 V, 60 Hz AC only, minimum 15 A circuit breaker
Water pressure 20 - 80 psi (140 - 550 kPa)
3
/4"(W) X 24 5/8"(D) X 33 5/8"(H)
Dimensions
Inlet water temperature 120 °F (49 °C) minimum, 149 °F (65 °C) maximum
Net weight 72 - 82 lbs. (33 - 37 kg)
23
603 mm(W) X 625 mm(D) X 854 mm(H)
5
13INSTALLATION
Preparing Cabinet Opening
This dishwasher is designed to t a standard
dishwasher opening. An opening may be needed
on both sides to route plumbing and electrical
connections.
24" (610 mm) min.
1
33 /
2" (851 mm) min.
24" (610 mm) min.
Select a location as close to the sink as possible
1
for easy connections to water and drain lines.
To ensure proper drainage, install the
2
dishwasher no more than 12 ft. (3.65 m) from
the sink.
WARNING
• Don't use existing holes unless they are in the
target area. Otherwise, the water supply and
drain hose may be damaged by being crushed
or kinked.
CAUTION
• Failure to properly locate the hole for the water
and drain lines may prevent the dishwasher from
installing ush with the cabinets and could result
in kinked or damaged lines. Installation damage
is not covered by the warranty, and leaks caused
by improper installation may result in property
damage.
For ush installations only, you may remove the
cabinet brace inside the cabinet.
Cabinet brace
ENGLISH
If installing the dishwasher in a corner, leave a
3
minimum of 2" (50 mm) between the dishwasher
and the adjacent wall.
To allow for proper clearance of plumbing and
4
electrical, use the template included with the
literature to determine the clearance on the side
of the cabinet where the cabinet meets the back
wall. Using a 2
in the target area as shown on the template.
1
/2" diameter hole saw, drill a hole
4
9
14 INSTALLATION
Preparing Electrical Wiring
Operate this appliance with the correct voltage
1
as shown in this manual and on the rating plate.
Connect it to a dedicated, properly grounded
branch circuit which is protected by a time delay
fuse. Connect the appliance using 3-wires,
including a ground wire.
If an outlet and other power connector are used,
2
it should be in an accessible location adjacent
to and not behind the dishwasher and within 4 ft
(1.2 m) of the dishwasher's side.
The wiring must be grounded properly. If in
3
doubt, have it checked by a qualied electrician.
Do not connect any other appliance to the same
outlet.
Route the wiring.
4
Preparing Water Supply
Connection
Make sure the house water supply is turned off
before connecting the dishwasher water lines.
Connect the dishwasher to a hot water supply
1
with a temperature range between 120 °F (49
°C) and 149 °F (65 °C). This temperature range
provides the best washing results and shortest
cycle time. To prevent damage to dishes, the
temperature should not exceed 149 °F (65 °C).
When connecting the dishwasher water line,
2
sealing tape or compound should be used on
pipe threads to avoid leaks. Tape or compound
should not be used on compression ttings.
The water supply tube must be located in the left
3
side channel.
Electrical cable
Make sure the electrical cable is oriented in the
5
right side channel.
1
4 /2" - 6”
(115 mm - 152 mm)
WARNING
• For personal safety, remove house fuse or open
circuit breaker before installation.
• Do not use an extension cable or adapter with
this dishwasher.
NOTE
• If you nd any damage to the dishwasher, contact
your retailer or contractor.
• The included wire nut in 16AWG should be used.
1 3
6 /2" - 7 /4"
(165 mm - 197 mm)
Water supply line
NOTE
• Use new hoses when connecting to the water
supply. Do not reuse old hoses.
Loading...