LG HF65LA User Manual

OWNER'S MANUAL

LG CineBeam

DLP Projector

Please read the safety information carefully before using this product.

HF65LA

P/NO : SAC37813512 (1901-REV00)

www.lg.com

LICENSES

Supported licenses may differ by model. For more information about licenses, visit www.lg.com.

ENGLISH

Manufactured under license from Dolby Laboratories. Dolby, Dolby Vision, Dolby Audio, Dolby Atmos, and the double-D symbol are trademarks of Dolby Laboratories.

For DTS patents, see http://patents.dts.com. Manufactured under license from DTS Licensing Limited. DTS, the Symbol, & DTS and the Symbol together, DTS

NOTE

• Image shown may differ from your projector.

• Your projector’s OSD (On Screen Display) may differ slightly from that shown in

this manual.

The terms HDMI and HDMI High-Denition

Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc. in the United States and other countries.

SAFETYPRECAUTIONS

Please take note of the safety instructions to prevent any potential accident or misuse of the projector. Child injuries can be prevented by following these simple safety precautions. The precautions should be followed in the same manner when you store or move your existing projector.

• Safety precautions are given in two forms, i.e., WARNING and CAUTION as

detailed below.

WARNING Failure to follow the instructions may cause serious injury and

even death.

CAUTION Failure to follow the instructions may cause personal injury or

product damage.

• Read the owner’s manual carefully and keep it on hand.

ENGLISH

WARNING/CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

The lightning ash with

arrowhead symbol, within an

equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of

sufcient magnitude to constitute a risk

of electric shock to persons.

The exclamation point within

an equilateral triangle is

intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING/CAUTION

- TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

Readtheseinstructions. Keeptheseinstructions. Heedallwarnings. Followallinstructions.

IndoorInstallation

WARNING

• Do not use the projector outside

and do not expose the product to any humidity or water.

- Since the product is not waterproof, this may result in a

re or electric shock.

• Do not place the projector in direct

sunlight or near heat sources such as radiators, fires, stoves, etc.

- This may result in re.

• Do not place flammable materials

such as aerosols near the projector.

- This may result in re.

• Do not allow children to cling to or

ENGLISH

climb up to the projector.

- This may cause the projector to fall, causing injury or death.

• Do not install the product in a

place with no ventilation (e.g., on a bookshelf or in a closet) or on a carpet or cushion.

- This may result in re due to the increase in internal temperature.

• Do not place the product close to

sources of steam, oil or oil mist, such as humidifiers and kitchen counters.

- Failure to do so may result in

re, electric shock, or corrosion.

• Do not install the product onto

a wall or ceiling that is close to sources of oil or oil mist.

- The product may be damaged and fall, resulting in serious injury.

• Do not place the projector where it

might be exposed to dust.

- This may result in re.

• Do not use the projector in a damp

place such as a bathroom where it is likely to get wet.

- This may result in re or electric shock.

• Do not allow a tablecloth or curtain

to block the air vent.

- This may result in re due to the increase in the internal temperature.

• Ensure good ventilation around the

projector. The distance between the projector and the wall should be at least 30 cm (11.8 inches).

- This will prevent re due to the increase in the internal temperature.

• When installing the product on a

ceiling, a professional technician should install it using authorized tools. If installed improperly, the product may fall.

- This may cause personal injury or property damage. For installation of the product, please contact the customer support center.

• If you use a ceiling mounting device,

adhesive to prevent loosening of screws, or if you apply oil or lubricant to the product, this may cause the case to crack and the product to fall. This may also cause serious personal injury to the person below the device (if any) and damage to the product as well.

CAUTION

• When placing the projector on a

table or shelf, be careful not to put it near the edge.

- The projector could fall due to balance problems, which may cause personal injury or damage to the product. Make sure to use the projector cabinet or stand

that ts the projector.

• When moving the projector, make

sure to switch it off and remove the power plug and cords.

- The power cord may be

damaged, resulting in re or

electric shock.

• Do not place the projector on an

unstable or vibrating surface such as a wobbly shelf or a slope.

- It may fall and cause injury.

• Be careful not to tip the projector

over when connecting external devices to the projector.

- This may cause personal injury or damage to the projector.

Power

WARNING

• DISCONNECTING THE DEVICE

FROM THE MAIN POWER

- The Power plug is the disconnecting device. In case of an emergency, the Power Plug must remain readily accessible.

• The grounding wire should be

connected. (Except for devices which are not grounded.)

- Ensure that you connect the grounding cable to avoid electric shock. If it is not possible to

ground the unit, have a qualied

electrician install a separate circuit breaker. Do not try to ground the projector by connecting it to telephone wires, lightning rods or gas pipes.

• The power plug should be inserted

fully into the power outlet.

- An unstable connection may

cause a re.

• Do not place heavy objects on the

power cord.

- This may result in re or electric shock.

• Never touch the power plug with

wet hands.

- This may result in electric shock.

ENGLISH

• Do not plug too many devices into

one multi-power outlet.

- This may result in re due to the power outlet overheating.

• Keep the AC adapter, power plug,

ENGLISH

and the used power outlet clean from dust or foreign materials building up.

- This may result in re.

• If there is any smoke or a burning

smell from the projector or AC adapter, stop using the product immediately. Disconnect the power cord from the power outlet, and then contact the customer service center.

- This may result in re.

• To turn off the main power, remove

the power plug, which should be positioned so it is easy to access for operation.

CAUTION

• Always grab the plug to remove the

AC adapter or power cord.

- Otherwise, this may result in a

re or may damage the product.

• Refrain from constantly bending the

power cord of the AC adapter.

- If the power cord is bent excessively for a long period of time, the cord may break

inside. This may result in a re or

electric shock.

• Ensure the power cord and plug are

not damaged, modified, severely bent, twisted, pulled, sandwiched or hot. Do not use the product if the power outlet is loose.

- This may result in re or electric shock.

• Keep the power cord away from

heating devices.

- The wire’s sheath may melt,

which may result in re or

electric shock.

• Place the projector where people

will not trip over or step on the power cord to protect the power cord and plug from any damage.

- This may result in re or electric shock.

• Do not turn the projector on or

off by plugging in the power plug or unplugging it from the power outlet. (Do not use the power plug as a switch.)

- This may result in electric shock or damage to the product.

• Do not insert a conductor into the

other side of the wall outlet while the power plug is inserted into the wall outlet. In addition, do not touch the power plug immediately after it is disconnected from the wall outlet.

- This may result in electric shock.

• Only use the official power cord

provided by LG Electronics. Do not use other power cords.

- This may result in re or electric shock.

• If any water or foreign materials

have gone into the AC adapter, power cord, or the interior of the projector, turn off the projector by pressing the power button. Remove all the cables, and then contact the customer service center.

- This may result in re or electric shock.

• The surface of the AC adapter is

hot. Keep the AC adapter out of the reach of children and avoid touching it during use.

• Never disassemble the power

supply devices (AC adapter/power cord, etc.).

- This may damage the power

cord and result in a re or

electric shock.

• Connect the AC adapter and the

power cord firmly.

- Not doing so may result in a

product failure or re.

• Do not place heavy objects or put

pressure on the power cord and AC adapter and avoid damage.

- This may result in a re or may damage the product.

• Always use the AC adapter provided

or any AC adapters approved and certified by LG Electronics.

- Any other AC adapter connected may result in the

screen ickering.

ENGLISH

WheninUse

WARNING

• Do not place anything containing

ENGLISH

liquid on top of the projector such as a vase, flower pot, cup, cosmetics, medicine, or ornaments, candles, etc.

- This may result in re or electric shock, or cause injury due to falling.

• In the event that there is a heavy

impact or the cabinet is damaged, switch it off, unplug it from the power outlet and contact an authorized service center.

- This may result in electric shock.

• Do not insert pieces of metal such

as coins, hairpins or metal debris, nor flammable materials such as paper or matches into the projector.

- This is to prevent electric shock

or re.

• Make sure that a child does not

swallow the batteries when you replace the old batteries in the remote control with new ones. Keep batteries out of reach of children.

- If a child swallows a battery, consult a doctor immediately.

• Never open any cover on the

projector.

- There is a high risk of electric shock.

• Do not look directly into the lens

when the projector is in use.

- The bright light may damage your eyes.

• When the lamp is on or has just

been turned off, avoid touching the air vent or lamp, because these will be very hot.

• If there is a gas leak in the room

with the projector, do not touch the projector or power outlet. Open the windows for ventilation.

- Sparks may cause re or burns.

• Unplug the power cord from the

outlet during a lightning storm.

- This will prevent shock or damage to the projector.

• Do not use the projector near

electronic devices that generate a strong magnetic field.

• Keep the plastic film used for

packaging the projector out of the reach of children.

- If not handled safely, it can cause suffocation.

• Do not keep your hand on the

projector for a long time when it is running.

• When you play a game by

connecting a game console to a projector, it is recommended that you maintain a distance of more than four times the diagonal length of the screen.

- Make sure that the connecting cable is long enough. Otherwise, the product may fall causing personal injury or damage to the product.

• Do not place the projector or its

remote control with batteries in an extremely high temperature environment.

- This may result in re.

CAUTION

• Do not place heavy objects on the

projector.

- It may fall down and cause personal injury.

• Be careful not to allow any impact

to the lens during transport.

• Do not touch the lens of the

projector.

- The lens may be damaged.

• Do not use any sharp tools on

the projector such as a knife or hammer, because this may damage the casing.

• In the event that no image appears

on the screen or no sound is heard, stop using the projector. Switch off the projector, unplug it from the power outlet and contact our service center.

- This may result in re or electric shock.

• Do not drop anything onto the

projector or allow anything to bang into the projector.

- This may cause damage to the projector or personal injury.

• It is recommended that you

maintain a distance of more than 5 to 7 times the diagonal length of the screen.

- If you watch the screen at a close distance for a long time, your eye sight may become worse.

ENGLISH

• Do not block the light beam emitted

from the projector using a book or other object.

- Lengthy exposure to the

ENGLISH

projector beam may result in

re. In addition, the lens may

be overheated and damaged by

the reected heat. Disable the

AV function to stop projection temporarily or turn off the power.

• Do not start the projector with the

volume turned up high.

- High volume may damage hearing.

• Do not use high voltage electrical

equipment near the projector, (e.g., a bug zapper). This may result in product malfunction.

Cleaning

WARNING

• Do not spray the projector with

water when cleaning. Make sure water does not flow into the projector.

- This may result in re or electric shock.

• When there is smoke or a strange

smell coming out from the projector or a foreign object falls into the projector, please switch it off and unplug it from the power outlet and contact our service center.

- Otherwise, this may result in re or electric shock.

CAUTION

• Contact your seller or our service

center once a year to clean the internal parts of the projector.

- If you do not clean the projector for a long period of time, dust will accumulate, which may

result in re or damage to the

projector.

• When cleaning plastic parts such

as the projector case, unplug the power first and wipe with a soft cloth. Do not spray with water or wipe with a wet cloth. Never use glass cleaner, automobile or industrial polish, abrasives, wax, benzene, or alcohol as these can damage the projector.

- This can result in re, electric shock or cause damage to the product (deformation and corrosion).

• Do not wipe the optical system

(lens, mirror) right after the product has been turned off or while the product is being operated. When cleaning each part of the product, remove the power cord and wipe gently with a soft cloth. Do not spray with water or wipe with a wet cloth. Do not use detergents, automobile or industrial polish, abrasive substances, wax, benzene, alcohol, water, etc. on the product’s main unit or optical system (lens, mirror) as this may damage the product.

- This can result in re, electric shock or cause damage to the product (deformation and corrosion).

• Remove the plug from the outlet

before cleaning the product.

- Otherwise, this may result in electric shock.

ENGLISH

Others

WARNING

• When you go out, place the

ENGLISH

projector out of reach of animals, and remove the power plug from the wall outlet.

- Using a damaged power cord

may result in short circuit or re.

• Do not use the projector near high-

precision electronic devices or those that transmit weak radio signal.

- This may affect the operation of the product, causing an accident.

• Only a qualified technician can

disassemble or modify the projector. For diagnosis, adjustment, or repair, contact your seller or our service center.

- This may result in re or electric shock.

• Proper ventilation required, do not

block airflow around unit. Doing so can cause injury and internal overheating.

• Do not touch the lens; doing so can

result in burns or damage to lens. Lens and unit may be HOT during and immediately after use. Use caution when handling unit, allowing for proper cool down.

• Only use a grounded electrical

outlet. (Except for devices which are not grounded.)

• Do not insert anything into or cover

up the exhaust vents.

- This may result in re or electric shock.

• Follow all maintenance guidelines

for optimal use; service only at an authorized service center.

• Keep the batteries and remote out

of reach of children.

- This will prevent personal injury or damage to the product.

CAUTION

• Do not use or store the projector

outdoors for long periods of time.

• Do not mix new batteries with old

ones.

- Burst or leaking batteries may result in damage or injury.

• Be sure to unplug if the projector is

not to be used for a long period.

- Accumulated dust may result

in re or electric shock due to

overheating, ignition, or poor insulation.

• Only use the specified type of

battery.

- Burst or leaking batteries may result in damage or injury.

• Make sure you use the same type

of battery when replacing.

- In the case of a battery contact failure, the battery may drain quickly or the remote control may not work properly.

• Dispose of used batteries properly.

- This may result in explosion

or re. The correct method of

disposal may vary depending on your country or region. Dispose of the battery pack as instructed.

• Do not throw or disassemble the

battery.

- This may result in re or explosion due to damage to the battery.

• Store batteries away from metallic

objects, such as keys and paper clips.

- Excess current may cause a rapid increase in temperature,

resulting in re or burns.

• Do not store the batteries near any

heat source, such as a heater.

- This may result in re or damage to the product.

• Do not store batteries at

temperatures higher than 60 °C (140 °F) or in high humidity.

- This may result in explosion

or re.

• Make sure that the battery is

installed correctly.

- This prevent explosion or re.

• Incorrect battery replacement may

cause fire.

• Batteries: Store the accessories

(battery, etc.) in a safe location out of the reach of children.

Risk Group 2

CAUTION Possibly hazardous optical radiation

emitted from this product. Do not stare at operating lamp. May be harmful to the eye.

This label is attached to the bottom of

the product and language may differ.

ENGLISH

ANTENNA

WARNING

• If you are using an outdoor antenna,

ENGLISH

please install it away from electrical wires to make sure it does not touch any nearby wires even when it falls down due to heavy wind.

- Failure to do so may cause electric shock or physical injury.

CAUTION

• To prevent any water flowing into

the product, install a drip loop in the outdoor antenna wire where it comes indoors.

- Raindrops owing into the

product may cause re or

electric shock.

OutdoorAntennaGrounding

• If an outdoor antenna is installed,

follow the precautions below. An outdoor antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can come in contact with such power lines or circuits as death or serious injury can occur. Be sure the antenna system is grounded to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code (NEC) in the U.S.A. provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes and requirements for the grounding electrode.

Antennagroundingaccordingto theNationalElectricalCode,ANSI/ NFPA70

Ground Clamp

Electric Service

Equipment

Ground Clamp

NEC:NationalElectricalCode

Antenna Lead in Wire

Antenna Discharge Unit (NEC Section 810-20)

Grounding Conductor (NEC Section 810-21)

Power Service Grounding Electrode System (NEC Art 250, Part H)

ForUSA

NOTETOCABLE/TVINSTALLER

This reminder is provided to call the CATV system installer’s attention to Article 820 - 40 of the National Electric Code (U.S.A.). The code provides guidelines for proper

grounding and, in particular, species

that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical.

ENGLISH

CONTENTS

LICENSES 2

ENGLISH

SAFETYPRECAUTIONS 3

PREPARATION 17

Accessories 17

OptionalExtras 18

PartsandComponents 19

UsingtheJoystickButton 21

- Basic functions 21

- Adjusting the menu 22

ProjectorStatusIndicators 22

Installation 23

- Installation Precautions 23

- Projection Distance per Screen Size 25

- Kensington Security System 27

MAGICREMOTECONTROL 28

ToRegistertheMagicRemote Control 30

ToRe-registertheMagicRemote Control 30

UsingtheMagicRemoteControl31

USINGTHEPROJECTOR 32

ConnectingtheAntennaorCable   32

- Focus of the Screen Image 33

- Watching With the Projector 33

CONNECTINGDEVICES 34

HDMIConnection 35

- Connecting to HD Receiver, DVD, or External Devices 35

- Connecting a PC 36

- Connecting a Laptop 37

ConnectingHeadphones 38

ConnectingaDigitalAmp 39

Connectingasmartdevice (smartphone,tablet,etc.) 40

- Slimport supported devices 40

- Apple Lightning Digital AV adapter supported devices 40

- Apple 30-pin Digital AV adapter supported devices 40

MAINTENANCE 41

Cleaning 41

- Cleaning the Lens 41

- Cleaning the Projector Case 41

SPECIFICATIONS 42

OpenSourceSoftwareNotice Information 46

SYMBOLS 47

PREPARATION

The pictures may differ slightly from the actual product.

Accessories

Accessories included with the projector are show below. Accessories are subject to change without prior notice. New accessories may be added or old ones removed.

Magic Remote Control

Two AA Batteries

Power cord AC-DC Adaptor

• When connecting an HDMI or USB cable, or

connecting a USB flash drive to the HDMI or USB port, use a product that has a width of 18 mm (0.7 inches) or less and a height of 10 mm (0.3 inches) or less. If the USB cable or USB flash drive does not fit the USB ports of the projector, use an extension cable that supports USB 2.0.

Owner's Manual

ENGLISH

• When connecting two USB devices at the same time, each one should have

bezels less than 8.5 mm (0.3 inches) thick.

• Use a certified cable with the HDMI logo attached.

• If you do not use a certified HDMI cable, the screen may not display or a

connection error may occur. (Recommended HDMI cable types)

- Ultra High-Speed HDMI®/™ cable (3 m (9.8 feet) or less)

OptionalExtras

To purchase optional accessories, visit an electronics store or online shopping site or contact the retail store where you purchased the product. Optional accessories are subject to change without prior notice.

ENGLISH

Projection Screen HDMI Cable RF Cable

Optical Cable LG Audio Device

PartsandComponents

This projector is manufactured using high-precision technology. You may, however, see tiny black dots and/or bright colored dots (red, blue, or green) that continuously appear on the projector screen. This is a normal result of the manufacturing process and does not indicate a malfunction.

Joystick Button

ENGLISH

Mirror

Outlet Vent

Speaker

Inlet Vent

Focus Ring

Lens

Speaker

Inlet Vent

IR Receiver

Bottom of the Projector

Adjustable leg

1) Due to the high temperature of vent area, do not get close to the vent area.

2) Do not touch the lens and mirror when using the projector. The lens may be damaged. (Keep lens away from sharp objects.)

3) Turn the adjustable leg left or right to adjust the angle.

ENGLISH

Side

Back

1 2

3

4

5

6

7 8

No. Description

1

(Headphone Port)

2

USB Port

3

4

5

6

7

8

9

Port

IR Receiver

Port

9

Port

UsingtheJoystickButton

You can operate the projector by pressing the button or moving the joystick left, right, up, or down.

Basicfunctions

PowerOn When the projector is turned off, place

your nger on the joystick button, press it

once, and release it.

PowerOff Press and hold the joystick button for

more than 3 seconds while the projector is on.

Volume Control

Channels Control

NOTE

• Place your finger over the joystick button and move it up, down, left, or right. Be

careful not to press the joystick button. If you press the joystick button first, you may not be able to adjust the volume level and/or scroll through saved channels.

Place your nger over the joystick button

and move it left or right, you can adjust the volume level.

Place your nger over the joystick button

and move it up or down, you can scroll through the saved channels.

ENGLISH

Adjustingthemenu

When the projector is turned on, press the joystick button one time. You can adjust the menu items ( , , , ) moving the joystick button left, right, up, or down. Move to the desired menu item, and then press the joystick button once to select it.

ENGLISH

Turns the power off.

Changes the input source.

Clears on-screen displays and returns to projector viewing.

Displays the Settings menu.

ProjectorStatusIndicators

LED Power

Indicator

LED Power

Red

Off

Indicator

LEDPowerIndicator

Power standby state

The projector is operating with the power on.

Installation

InstallationPrecautions

• Place the projector in a well-

ventilated environment.

- To prevent internal overheating, install the projector in a wellventilated place. Do not place anything near the projector. That may block its air vents. If the air vents are blocked, the internal temperature of the projector will increase.

- Do not place the projector on a carpet or rug. If the projector’s inlet vent is on the bottom, be careful not to block the vent and always use the projector on a solid, level surface.

- Be sure to prevent foreign objects such as paper debris from entering the projector.

ENGLISH

- Leave an adequate open area (30 cm (11.8 inches) or more) around the projector.

• Do not place the projector in a hot,

cool, or humid environment.

• Do not place the projector in a place

where it will easily attract dust.

- This may result in re.

• Never open any cover on the

projector. There is a high risk of electric shock.

• The projector is manufactured using

high-precision technology. You may, however, see tiny black dots and/ or bright colored dots (red, blue or

ENGLISH

green) that continuously appear on the projector screen. This is a normal result of the manufacturing process and does not indicate a malfunction.

• The remote control may not work

in an environment where a lamp equipped with electronic ballasts or a three-wavelength fluorescent lamp is installed. Replace the lamp with an international standard lamp for the remote control to work normally.

• To install to the ceiling, attach the

ceiling-type bracket to the projector with M4 x 8 mm screws.

• Do not overtighten the screws. It

may damage the case, causing the projector to fall and cause a serious injury. (Recommended Torque: 4.34 ~ 6.94 ibf-in (5~8 kgf·cm))

ProjectionDistanceperScreenSize

1 Place the projector on a sturdy, level surface, together with the PC or audio/

video source.

2 Place the projector an appropriate distance away from the screen. The distance

between the projector and the screen determines the actual size of the image.

3 Position the projector so that the lens is at a right angle to the screen. If the

projector is not at a right angle, the projected image will look distorted. To correct the distortion, use the Edge Adjustment function.

4 Connect the power cord of the projector and the connected device to the wall

outlet.

Ratioofupwardprojection:125%

Screen

ENGLISH

ScreenSize

HorizontalSize(X)

ENGLISH

xVerticalSize(Y)

The projection distance may vary depending on the installation conditions.

NOTE

• If the projected image looks distorted or bent, check to see if the screen is

installed properly.

mm 1524 1778 2032 2286 2540

inches 60 70 80 90 100

1328 x

inches

inches 16.2 18.9 21.6 24.3 27.0

inches 4.1 6.8 9.4 12.1 14.8

inches 5.8 7.1 8.3 9.6 10.8

inches 9.4 10.7 11.9 13.2 14.4

52.2 x

mm 414 482 550 618 686

mm 105 173 241 309 377

mm 149 181 213 245 276

mm 241 273 304 336 368

747

29.4

1550 x

872

61.0 x

34.3

1771 x

996

69.7 x

39.2

1992 x

1121

78.4 x

44.1

2214 x

1245

87.1 x

49.0

KensingtonSecuritySystem

• This projector has a Kensington Security Standard connector as an anti-theft

mechanism. Connect a Kensington Security System cable as shown below.

• For more information on installation and use of the Kensington Security System,

refer to the user’s guide provided with the Kensington Security System.

• The Kensington Security System is an optional accessory.

• What is Kensington?

Kensington is a company that provides safety systems for laptops and other electronic devices. Website: http://www.kensington.com

ENGLISH

MAGICREMOTECONTROL

If the battery low message appears while using the Projector, replace the batteries.

ENGLISH

As shown in the gure, press the top of the battery cover

and slide it down the cover. Insert two new and identical batteries (1.5 V, AA type) with + and - poles pointing in the correct direction in the remote control.

NOTE

• Do not mix new batteries with old ones.

(POWER)

Turns the Projector on or off.

(STBPOWER)

You can turn your set-top box on or off by adding the set-top box to the universal remote control for your Projector.

Numberbuttons

Enters numbers.

(Dash)

Inserts a dash between numbers such as 2-1 and 2-2.

Accesses the saved channel list.

You can access apps or Live TV using the number buttons corresponding to the features.

(ScreenRemote)

Displays the Screen Remote.

- Accesses the Universal Control Menu in some regions.

(ScreenRemote)

Enables SAP (Secondary Audio Program) Feature.



Adjusts the volume level.

(MUTE)

Mutes all sounds.

(MUTE)

Accesses the [Accessibility] menu.

Scrolls through the saved channels.

(SEARCH)

Search for content such as channels, movies and other videos, or perform a web search by entering your search terms in the search box.



Accesses the Home menu.



Displays the list used previously.

(Q.Settings)

Accesses the Quick Settings.

(Q.Settings)

Displays the [All Settings] menu.

Press the up, down, left or right button to scroll the menu. If you press the pointer will disappear from the screen and Magic Remote will operate like a general remote control. To display the pointer on the screen again, shake Magic Remote to the left and right.

Wheel(OK)

Press the center of the Wheel button to select a menu. You can change channels by using the Wheel button.

Returns to the previous screen.

Clears on-screen displays and returns to last input viewing.

Changes the picture mode.

Shows channels guide.

(INPUT)

Changes the input source.

(INPUT)

Displays all the lists of external inputs.

(Up/Down/Left/Right)

buttons while the pointer is in use,



ENGLISH

Changes the aspect ratio of the screen per pressing of the button.

Coloredbuttons

These access special functions in some menus.

Controlbuttons(

You have access to premium content, video content and devices that support SIMPLINK.

By zooming in on the selected area, you can view it in full screen.

, )

* : To use the button, press and hold for more than 3 seconds.

ToRegistertheMagicRemoteControl

To use the Magic Remote control, register it with your projector rst.

1 Put batteries into the Magic Remote and turn the Projector on. 2 Point the Magic Remote at your projector and press the Wheel(OK) on

ENGLISH

the remote control.

• If the projector fails to register the Magic Remote, try again after turning the

projector off and back on.

ToRe-registertheMagicRemoteControl

1 Press the and buttons at the same time, for ve seconds, to unpair

the Magic Remote with your projector.

2 Press the Wheel(OK) button towards the projector to re-register the

magic remote control.

• Pressing and holding the button will let you cancel and re-register Magic

Remote at once.

+ 139 hidden pages