English
Español
LG Electronics
BLUETOOTH® Headset
HBM-W600 User Manual
Rev 1.0 US
All rights reserved. LG Electronics Inc., 2012
Note: For the best performance and to prevent any damage to, or misuse of the HBM-W600, please read all of the information carefully before to use.
WARNING :
This product contains chemicals known to the State of California to cause cancer and birth defects or reproductive harm.
Wash hands after handling.
ENG
2
Table of Contents
Introduction |
3 |
- Included in package |
3 |
Description of Parts |
4 |
How to Use |
4 |
- Change Direction |
4 |
- Charging |
5 |
- Low Battery |
5 |
- Battery Status Alert |
5 |
- Power On |
5 |
- Power Off |
5 |
- Pairing |
6 |
- Auto-Reconnect |
7 |
- Volume Control |
7 |
- Calling |
7 |
• Answering a call |
7 |
• Making a call |
7 |
• Voice dialing |
8 |
• Last number redial |
8 |
• Ending a call |
8 |
• Transferring a call |
8 |
• Call waiting |
8 |
• Call reject |
8 |
• Mic mute |
8 |
- Advanced Multipoint |
9 |
- Audio Streaming (A2DP) |
10 |
- HD Voice |
10 |
- SMS Reader |
10 |
Summary of Button Functions |
11 |
LED Indication |
12 |
Troubleshooting |
12 |
Specification |
13 |
Precautions |
13 |
Declaration of Confirmation |
14 |
Additional Information |
14 |
Limited Warranty |
17 |
Important Safety Information |
17 |
Introduction
The LG HBM-W600 is a light weight wireless headset that uses Bluetooth® technology.
This product can be used as an audio accessory for devices that support the headset, hands-free or A2DP Bluetooth profiles.
Included in the Package
ENG
LG HBM-W600 |
Ear Loop |
Charger |
Bluetooth® Headset |
|
|
NFC Tag |
Ear Buds(2) |
User Manual |
Warranty Card |
3
ENG
4
Description of Parts
Front
LED Indicator
Wireless
Charging Area
Microphone
Back
Charging Port
How to Use
Power/Call Button
Volume Up/Down
Button
Speaker
Change Direction |
|
Left |
Right |
How to Use
Charging
1) Adaptor Charging
- When the charger is connected with power on or off, the headset will turn off. - While charging, the LED indicator of HBM-W600 will show a solid white light - The buttons will not function while the device is charging.
- It takes 2 hours to fully charge the headset.
- When charging is complete, the LED indicator of HBM-W600 will turn off.
2) Wireless Charging
-When HBM-W600 is placed on the LG WCP-700 Wireless Charging Pad, the headset will remain on.
-While charging, the LED indicator of HBM-W600 will blink.
-It takes 2 hours to fully charge the headset.
-When charging is completed, the LED indicator of pad will turn solid green.
Low Battery
-An announcement will play once every 2 minutes.
-If the battery is not charged, the headset will turn off.
Battery Status Alert
-By pressing and holding the VOLUME DOWN button for 3 seconds, you can check the battery status of the HBM-W600. The audible battery status alert will inform you of the battery level. There are 3 levels of battery power:
1.Battery High
2.Battery Medium
3.Battery Low
Power On
-Press and hold the POWER/CALL button for 3 seconds.
• The power will turn on and a startup tone will play.
-The audible battery status alert will let you know the battery level.
Power Off
-Press and hold the POWER/CALL button for 3 seconds.
•A shutdown tone will play, the Bluetooth link will disconnect and the power will turn off.
ENG
5
ENG
6
How to Use
Pairing
-Before using the headset for the first time, it must be paired with a Bluetooth enabled device.
-There are 2 pairing modes with the HBM-W600.
1) Easy Pairing
a) Press and hold the POWER/CALL button for 3 seconds to turn on the HBM-W600.
b) The headset will enter auto-reconnect mode for 10 seconds.
(If your headset has already been paired with a device, the headset will automatically reconnect to the device when the HBM-W600 is powered on.)
c) After 10 seconds, the HBM-W600 will automatically enter pairing mode. d) When the headset enters pairing mode, the LED indicator will show a solid
white light.
e) Using your handset, find the Bluetooth menu and “search for” or“add” new devices.
f) Select “LG HBM-W600” from the list of devices to pair it with your device. g) If you are asked for a passkey or PIN during pairing, please enter “0000”
(4 zeros).
h) Once the devices are paired, you will hear “Headset paired”.
i) After pairing has been completed, make sure you “connect” to the
LG HBM-W600.
j) If you want to pair with a different device in the future, the headset must be placed into pairing mode.
k) If the headset is in pairing mode for 3 minutes without being connected to a device, the HBM-W600 will automatically turn off.
2) Manual Pairing
a) With the power off, press and hold the POWER/CALL button for 6 seconds. b) Continue pairing process from letter “e)” above.
3) NFC Pairing
a) Place HBM-W600 into pairing mode.
b) Touch NFC and Bluetooth enabled handset to NFC tag.
c) NFC and Bluetooth enabled handset will connect with
the HBM-W600 automatically.
NOTE: Place the NFC tag on the center of handset’s battery door with NFC pairing feature.
|
|
How to Use |
|
|
|
Auto-Reconnect |
|
||
|
|
|||
|
- If the HBM-W600 is turned off (either accidentally or intentionally) while connected, |
ENG |
the headset will disconnect from the device.
The headset and handset will automatically reconnect when the HBM-W600 is turned back on (provided that both devices are within the required range of 33 feet (10 meters).
Out of range
-When the connected device and the HBM-W600 are separated by a range of 33 feet (10 meters) or more, the headset will alert the user with a beep, and the headset and device will disconnect.
-When the device and the HBM-W600 are within the required range again, the HBM-W600 will automatically reconnect to the device.
-If the headset and device do not automatically reconnect when they are back within the required range, briefly press the POWER/CALL button on the HBM-W600 to reconnect manually.
-While trying to reconnect, your headset will beep and the LED indicator will flicker twice every 5 seconds.
-If the headset does not reconnect within 60 minutes, it will turn off.
Volume Control
-Press the VOLUME UP or VOLUME DOWN button to adjust the speaker volume.
-There are eight levels of speaker volume.
-To avoid hearing loss at high volume, HBM-W600 will play a warning tone when the volume is raised into the upper 3 levels.
Calling
Answering a call
-When there is an incoming call, the headset will ring.
-Briefly press and release the POWER/CALL button to answer the incoming call.
Making a call
-If you make a call from the connected handset, the call will (depending on the phone settings) automatically transfer to the headset. If the call is not automatically transferred, you can manually transfer the call by briefly pressing the POWER/CALL button on the
HBM-W600 (handset and headset must be paired).
7
ENG
8
How to Use
Voice dialing
-Briefly press the POWER/CALLbutton to activate “Voice dialing”.
For best results, record the voice dialing tag through your headset.
NOTE: If your handset does not support voice dialing, this action may activate Last Number Redial.
Last number redial
-Press and hold the POWER/CALLbutton for 1 second to activate “Last number redial”.
The headset will beep and then call the last number dialed.
*Feature will not work if held for longer than 1 second.
Ending a call
- Briefly press the POWER/CALL button.
Transferring a call
-While on a call on your handset, briefly press the POWER/CALLbutton to transfer the audio to the headset (the headset and handset must be paired).
-To transfer a call from the headset to handset, press and hold the VOLUME UP button for 3 seconds.
Call waiting
-Answer a second call without hanging up the first by pressing the CALL button for 1 second (You will hear a beep). Press the POWER/CALL button for 1 second to return to the original call.
-Briefly press the POWER/CALLbutton to end the active call or both calls at once. (subject to handset support)
Call reject
-Activate call reject by pressing the POWER/CALLbutton for 1 second when the handset rings.
*These functions may only be used if your handset supports them.
For further information about using these features, please consult your handset’s user manual.
Mic mute
-Press and hold the VOLUME UP and VOLUME DOWN buttons simultaneously for 1 second to mute/unmute the mic during conversation.
How to Use
Advanced Multipoint
The HBM-W600 is capable of having two devices connected to the headset at the same time. This will give you the freedom of using call waiting between calls on both of your connected phones.
Connection
-Pair the headset with one of your Bluetooth-enabled handsets (per the pairing instructions on page 6).
-Turn off the headset.
-With the power off, press the POWER/CALL button and move the power switch to the ‘ON’ position at the same time for 4 seconds to enter Manual Pairing mode.
-Now, pair and connect the headset with your other Bluetooth-enabled handset. (This will be your primary handset).
-Once this handset is paired and connected, go back and connect the originally paired handset to the headset. (This will now be your secondary handset).
*NOTE: When the HBM-W600 is connected to two handsets at the same time(multipoint), the headset calling functions will work with the primary handset.
Calling function
-Voice Dialing and Last Number Redial features work with the primary handset (or handset which made the last outgoing call).
Call waiting
-While speaking on an active call, press the call button for 1 second to switch to an incoming call.
-To switch between 2 active calls, press the call button for 1 second.
-To end both calls briefly press the call button.
-If both handsets are receiving an incoming call, the headset will default to the primary device.
ENG
9
ENG
How to Use
Audio Streaming (A2DP)
The HBM-W600 supports music streaming (A2DP).
When you play music from your A2DP enabled device, it will automatically transfer to your headset. Music will automatically pause when you have an incoming call. When the call is ended the music will start playing again.
A2DP allows streaming of all audio from your handset and running applications including music and GPS navigation.
HD Voice
The HBM-W600 supports high definition voice calling and audio streaming.
*Network must support HD Voice for higher quality calling.
SMS Reader
The HBM-W600 supports SMS reading on Android TM based devices.
In Google Play search for the LG “BT Reader” application and install on your device to use this function.
*The 2D barcode shown below helps you download the LG “BTReader” application from Google Play.
10
Summary of Button Functions
Function |
HBM-W600 |
|
Status |
||
|
||
Power on |
Power off |
|
Power off |
Power on |
|
Volume up |
Talking |
|
Volume down |
Talking |
|
Transferring a call |
Talking |
|
Answering a call |
Ringing |
|
Ending a call |
Talking |
|
Call waiting |
Talking |
|
Last number redial |
Idle |
|
Voice dialing |
|
|
(handset must |
Idle |
|
support) |
|
|
Call reject |
Ringing |
|
Mic on/off |
Talking |
|
Pairing mode |
Power off |
|
(Manual) |
||
|
||
Battery status check |
Idle |
|
NFC pairing |
Pairing |
|
|
|
Action
Press the POWER/CALL button for 3 seconds.
Press the POWER/CALL button for 3 seconds.
Briefly press the VOLUME UP button. Briefly press the VOLUME DOWN button.
-Handset to headset
Briefly press the POWER/CALL button. (must be paired)
-Headset to handset
Press and hold the VOLUME UP button for 3 seconds.
Briefly press the POWER/CALL button. Briefly press the POWER/CALL button.
Press the POWER/CALL button for 1 second. Press the POWER/CALL button for 1 second.
Briefly press the POWER/CALL button.
Press the POWER/CALL button for 1 second.
Press and hold VOLUME UP and VOLUME DOWN buttons simultaneously for 1 second.
Press the POWER/CALL button for 6 seconds.
Press the VOLUME DOWN button for 3 seconds.
Touch NFC and Bluetooth enabled handset to NFC tag.
ENG
11
ENG
LED Indication
Function |
HBM-W600 Status |
Action |
|
|
Power on |
The LED will flash 4 times. |
|
|
Power off |
The LED will flash 4 times and then turns off. |
|
|
Pairing mode |
The LED stays on. |
|
Operating |
Headset / Hands-Free / |
The LED will flash twice every 5 seconds. |
|
A2DP profiles connected |
|||
|
Call connected |
The LED will flash twice every 5 seconds. |
|
|
Out of range |
For the first 15 minutes after the devices are |
|
|
disconnected the LED will flash twice every 5 |
||
|
|
seconds. After that it will flash once every 5 seconds. |
|
|
Charging |
(Adaptor Charging) The LED stays on. |
|
Charging |
(Wireless Charging) Depends on the HBM-W600 status. |
||
|
|||
Charging complete |
(Adaptor Charging) The LED turns off. |
||
|
|||
|
(Wireless Charging) Depends on the HBM-W600 status. |
||
|
|
Troubleshooting
Issue |
Possible problem |
Resolution |
||
Does not turn on |
Check whether the battery |
Charge the battery. |
||
of the HBM-W600 is fully |
||||
|
|
charged. |
|
|
|
|
Check whether the device |
Determine whether your device |
|
Unable to |
supports the headset or |
supports the Headset or Hands- |
||
communicate with |
hands-free Bluetooth profiles. |
free Bluetooth profiles. |
||
the LG HBM-W600 |
|
Check whether the battery of |
Charge the battery. |
|
|
|
the HBM-W600 is low. |
||
|
|
|
||
|
|
Check and make sure the |
Press and hold the POWER/CALL |
|
|
|
button for at least 3 seconds to |
||
|
|
headset is on. |
||
Unable to pair the |
turn on the headset. |
|||
|
||||
HBM-W600 with |
|
Check and make sure the |
With the Power off, press and |
|
Bluetooth device |
POWER/CALL button for 6 seconds |
|||
|
|
headset is placed in pairing |
to manually place the headset in |
|
|
|
mode. |
||
|
|
pairing mode. |
||
|
|
|
||
Low sound (speaker) |
Check the speaker volume. |
lncrease the volume level. |
||
Cannot hear audio |
Check whether the device is |
Start device streaming. |
||
streaming |
streaming. |
|||
|
12