LG HB6422BGF Owner’s Manual
Installation and Operating Instructions
Built-In Gas Cooktops
To avoid the risk of accidents or damage to the Gas Cooktops, it is essential to read these operating instructions
before it is installed or used for the first time. And please keep this manual for later reference.
HB6422BRU
P/No.: MFL62060313 |
www.lg.com |
Contents
Introduction ................................................................................. |
3 |
|
1. |
Instructions for safe and proper use ....................................... |
3 |
Instructions for the installer ....................................................... |
5 |
|
2. |
Positioning of the hob ............................................................. |
5 |
3. |
Electrical connection ............................................................... |
7 |
4. |
Gas connection ....................................................................... |
8 |
5. Adaptation to different types of gas ...................................... |
10 |
|
6. |
Final operations .................................................................... |
13 |
Instructions for the user ........................................................... |
15 |
|
7. |
Using the hob ....................................................................... |
15 |
8. |
Cleaning and maintenance ................................................... |
17 |
These instructions are valid only for end user countries whose identification symbols appear on the cover of this manual.
INSTRUCTIONS FOR THE INSTALLER: these are for the authorised person who must carry out a suitable check of the gas system, install the appliance, set it functioning and carry out an inspection test.
INSTRUCTIONS FOR THE USER: these contain user advice, description of the commands and the correct procedures for cleaning and maintenance of the appliance.
2
Introduction
1. Instructions for safe and proper use
This manual is an integral part of the appliance and therefore must be kept in its entirety and in an accessible place for the whole working life of the cooking hob. We advise reading this manual and all the instructions therein before using the cooking hob. Also keep the series of nozzles supplied. Installation
must be carried out by qualified personnel in accordance with the regulations in force. This appliance is intended for domestic uses and conforms to current regulations in force. The appliance has been built to carry out the following functions: Cooking and heating-up of food. All other uses are considered improper.
The manufacturer declines all responsibility for improper use.
Do not leave the packing in the home environment. Separate the various waste materials and take them to the nearest special garbage collection centre.
It is obligatory for the electrical system to be grounded according to the methods required by safety rules.
The plug to be connected to the power cable and the socket must be the same type and must conform to current regulations.
Never unplug by pulling on the cable.
Immediately after installation carry out a brief inspection test of the cooking hob, following the instructions below. Should the appliance not function, disconnect it from the supply and call the nearest technical assistance centre.
Never attempt to repair the appliance.
Always check that the control knobs are in the position “ZERO”(OFF) when you finish using the hob.
3
Introduction
The identification plate, with technical data, serial number and marking is clearly visible under the casing.
The plate on the casing must not be removed.
Before connecting the device, make sure that it has been regulated for the type of gas that will feed it, checking the label under the casing.
Do not put pans without perfectly smooth and flat bottoms on the cooking hob grids.
Do not use recipients or griddle plates that extend beyond the external perimeter of the hob.
The hob is to be used by adults only. Do not let unsupervised children play with the hob.
This appliance is designed for cooking food and it shall not be used as a space heater.
Do not spray aerosols in the vicinity of this appliance while it is in operation.
The manufacturer declines all responsibility for damage to persons or things caused by non-observance of the above prescriptions or by interference with any part of the appliance or by the use of non-original spares.
THIS APPLIANCE IS MARKED ACCORDING TO EUROPEAN DIRECTIVE 2002/96/ EC ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE). THIS
GUIDELINE IS THE FRAME OF EUROPEAN-WIDE VALIDITY OF RETURN AND RECYCLING ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT.
DO NOT USE OR STORE FLAMMABLE MATERIALS IN THE APPLIANCE STORAGE DRAWER OR NEAR THIS APPLIANCE.
DO NOT MODIFY THIS APPLIANCE
4
Instructions for the installer
2. POSITIONING OF HOB
The following operation requires building and/or carpentry work so must be carried out by a competent tradesman.
Installation can be carried out on various materials such as masonry, metal, solid wood or plastic laminated wood as long as they are heat resistant (T 90°C).
Never use silicone or other insulating products when installing the appliance; use only the rubber gasket provided.
2.1. Attachment to support structure
Create an opening with the dimensions shown in the figure in the top surface of the counter, keeping a minimum distance of 50 mm from the rear border. This appliance can therefore be mounted against walls higher than the work surface on condition that a certain distance “X” be kept between the appliance and the wall as shown in the figure so as to avoid damage from overheating. Make sure there is a minimum of 750 mm between the hot plate flames and any shelf that may be installed directly above them.
5
Instructions for the installer
Accurately position the gasket provided all around the outer edge of the hole in the top surface as shown in the figures below, pressing it down so as to make it adhere properly. For measurements, refer to the figure depending on the hob model to be installed, bearing in mind that in both models the front and rear sides must skim the hole. Secure the hob to the counter with brackets A (supplied). Carefully trim any excess from border B of the gasket. The distances in the following drawing refer to the hole on the inner side of the gasket.
In case of installation on a hollow compartment with doors, a separating panel has to be placed under the hob. Keep a minimum distance of 10 mm between the bottom of the unit and the panel surface. The panel has to be easily removable to allow access in the event of technical service.
6
Loading...