LG BX403BJD Users manual
Order Number : GETEC-C1-10-130 FCC Part 15 subpart B
Test Report Number : GETEC-E3-10-067 Page 1 / 1
APPENDIX G
: USER’S MANUAL
EUT Type: DLP PROJECTOR
FCC ID.: BEJBX403BJD
OWNER’S MANUAL
DLP PROJECTOR
Please read this manual carefully before operating
your set and retain it for future reference.
BX503
BX403B
www.lg.com
DLP PROJECTOR
DLP PROJECTOR
Warning - Class B
(b) For a Class B Digital device or peripheral, the instructions furnished the user shall include the fol-
lowing or similar statement, placed in a prominent location in the text of the manual:
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
Contents
Contents
Safety Instructions ............................................. 4
Names of parts
Main Body ................................................................. 7
Connecting Part ......................................................7
Control Panel ............................................................ 8
Remote Control .......................................................9
Installing Batteries ...................................................9
Projector Status Indicators ...................................10
Accessories ...............................................................11
Optional Extras .........................................................11
Installing and Composition
Installation Instructions .......................................... 12
Basic Operation of the Projector ........................13
Using Kensington Security System ....................14
Turning on the Projector .......................................15
Turning off the Projector .......................................15
Focus and Position of the Screen Image ......... 16
Selecting source mode ......................................... 16
Connection
Connecting to a Desktop PC ............................... 17
Connecting to a Notebook PC ............................ 17
Connecting to a Video Source ............................18
Connecting to a DVD .............................................18
Connecting to a D-TV Set-Top Box ...................18
Function
Video Menu Options
Adjusting Video ....................................................... 19
Picture mode ............................................................ 19
Color Temperature Control ................................... 20
Gamma Function .....................................................20
Gamma curve shift Function................................20
Brilliant color
White peaking Function .........................................21
Black level Function ................................................ 21
Expert color Function .............................................22
Reset ...........................................................................22
TM
Function ...................................... 21
Special Menu Options
Selecting Language ...............................................23
Using Aspect Ratio Function ...............................23
Overscan Function ..................................................23
Flip horizontal Function ......................................... 24
Flip vertical Function ...............................................24
Sleep time Function ...............................................24
Auto sleep Function ............................................... 25
Presentation timer Function .................................25
Using Digital Zoom Function ...............................26
Using Keystone Function ......................................27
Using Blank Function ............................................. 27
Selecting Blank image .........................................28
Captured Image Function .....................................28
Lamp mode Function ............................................28
Using Monitor out Function .................................29
Checking lamp time ...............................................29
Using Still Function ................................................. 29
Screen Menu Options
Auto configure Function........................................30
Using Phase Function ............................................30
Using Clock Function .............................................30
Using Horizontal Function.....................................31
Using Vertical Function ..........................................31
RS-232C
External Control Device Setup .............................32
Information
Supported Monitor Display ...................................37
Maintenance .............................................................37
Replacing the Lamp ............................................... 38
How to fix the lens cap to the projector ...........40
Specifications ...........................................................41
Disposal of your old appliance
1. When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by
the European Directive 2002/96/EC.
2. All electrical and electronic products should be disposed of separately from the municipal waste stream
via designated collection facilities appointed by your government or your local authorities.
3. The correct disposal of your old appliance will help prevent potential negative consequences for the
environment and human health.
4. For more detailed information about disposal of your old appliance, please contact your city office, waste
disposal service or the shop where you purchased the product.
5. The fluorescent lamp used in this product contains a small amount of mercury. Do not dispose of this
product with general household waste. Disposal of this product must be carried out in accordance to the
regulations of your local authority.
4
Safety Instructions
Safety Instructions
Please take note of the safety instructions to prevent any potential accident or misuse of the projector.
ᰶ Safety Instructions are given in two forms as detailed below.
WARNING : The violation of this instruction may cause serious injuries and even death.
NOTES : The violation of this instruction may cause injuries or damage to the projector.
After reading this manual, keep it in the place that you can access easily.
ᰶ
Indoor Installation WARNING
Do not place the Projector in direct
sunlight or near heat sources such
as radiators, fires, stove etc.
This may cause a fire hazard!
Do not block the vents of the projector or restrict air-flow in any way.
This would cause the internal temperature to increase and could cause a fire
hazard or damage to the unit!
Do not use the projector in a
damp place such as a bathroom
where it is likely to get wet.
This may cause a fire or an electric
shock hazard!
Do not place flammable materials in, on or near the projector.
This may cause a fire hazard!
Do not place the projector close
to sources of steam or oil such
as a humidifier.
This may create a fire hazard or an
electric shock hazard!
Do not place the projector directly on a carpet, rug or place where
ventilation is restricted.
This would cause its internal temperature to increase and might create a
fire hazard or damage the unit.
Indoor Installation NOTES
When installing the projector on
a table, be careful not to place it
near the edge.
The projector could fall causing injury
and damage to the projector.
Only use a suitable stand.
Disconnect from the power supply and remove all connections
before moving, or cleaning.
Do not hang on the installed
projector.
It may cause the projector to fall,
causing injury or death.
Do not place the projector where
it might be exposed to dust.
This may cause a fire hazard or
damage to the unit!
Ensure good ventilation around the
projector. The distance between
the projector and the wall should
be more than 30 cm.
An excessive increase in its internal
temperature may cause a fire hazard or
damage to the unit!
Only use the projector on a level
and stable surface.
It may fall and cause injury and/or
damage to the unit.
Power WARNING
Earth wire should be connected.
Ensure that you connect the earth ground
wire to prevent possible electric shock (That
is a Projector with a three-prong grounded
AC plug must be connected to a threeprong grounded AC outlet).
If grounding methods are not possible, have
a qualified electrician install a separate circuit
breaker.
Do not try to ground the unit by connecting
it to telephone wires, lightening rods, or gas
pipes.
5
The power cord should be inserted
fully into the power outlet to avoid
a fire hazard!
This may cause a fire hazard or damage
the unit.
Do not place heavy objects on
the power cord.
This may cause a fire or an electric
shock hazard!
Power WARNING
Safety Instructions
Never touch the power plug with
a wet hand.
This may cause an electric shock
hazard!
Power NOTES
Hold the plug firmly when
unplugging. If you pull the cord,
it may be damaged.
This may cause a fire hazard!
Place the projector where people
will not trip or tread on the power
cord.
This may cause a fire or an electric
shock hazard or damage to the unit!
Using WARNING
Do not place anything containing
liquid on top of the projector
such as flowerpot, cup, cosmetics or candle.
This may cause a fire hazard or
damage to the unit!
Do not plug-in too many items
into one power outlet.
It may result in overheating of the outlet and create a fire hazard!
Do not use if the power cord or
the plug is damaged or any part
of the power outlet is loose.
This may cause a fire or an electric
shock hazard or damage to the unit!
Prevent dust from collecting on
the power plug pins or outlet.
This may cause a fire hazard!
Ensure the power cord does not
come into contact with sharp or
hot objects.
This may cause a fire or an electric
shock hazard or damage to the unit!
Do not turn the projector On/Off by plugging-in or unplugging the
power plug to the wall outlet.
(Allow the unit to cool before removing power.)
It may cause mechanical failure or could cause an electric shock.
In case of impact shock or damage
to the projector switch it off and
unplug it from the power outlet and
contact an authorized service center.
This may cause a fire or an electric shock
hazard or damage to the unit!
Do not allow any objects to fall
into the projector.
This may cause an electric shock hazard or damage to the unit!
If water is spilt into the projector unplug it from the power supply
immediately and consult your Service Agent.
This may cause an electric shock hazard or damage to the unit!
Do not remove any covers. High
risk of Electric Shock!
Don’t look directly into the lens
when the projector is in use. Eye
damage may occur!
Dispose of used batteries
carefully and safely.
In the case of a battery being
swallowed by a child please consult
a doctor immediately.
Do not touch metal parts during
or soon after operation since the
vents will remain very hot!
CAUTION concerning the Power Cord
It is recommend that most appliances be placed on a dedicated circuit; that is, a single outlet circuit
which powers only that appliance and has no additional outlets or branch circuits.Check the specification
page of this owner's manual to be certain.
Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords,
frayed power cords, or damaged or cracked wire insulation are dangerous.Any of these conditions could
result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance
indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord
replaced with an exact replacement part by authorized service personnel.
Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched,
closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the
cord exits the appliance.
6
Safety Instructions
Using WARNING
If the projector is in a room that experiences a gas leak, do not touch
the projector.
It can cause a fire or a burn by a spark.
Using NOTES
Do not place heavy objects on
top of projector.
This may cause mechanical failure or
personal injury!
Do not use any sharp tools on
the projector as this will damage
the casing.
Take care not to impact the lens
particularly when moving the
projector.
In the event that an image does
not appear on the screen please
switch it off and unplug it from the
power outlet and contact your
Service Agent.
This may cause a fire or an electric
shock hazard or damage to the unit!
Cleaning WARNING
Do not use water while cleaning
the projector.
This may cause damage to the projector or an electric shock hazard.
In the unlikely event of smoke or
a strange smell from the projector, switch it off, unplug it from
the wall outlet and contact your
dealer or service center.
This may cause a fire or an electric
shock hazard or damage to the unit!
Always open the lens door or
remove the lens cap when the
projector lamp is on.
Do not touch the lens of the projector. It is delicate and easily
damaged.
Do not drop the projector or
allow impact shock.
This may cause mechanical failure or
personal injury!
Use an air spray or soft cloth that
is moist with a neutral detergent
and water for removing dust or
stains on the projection lens.
Cleaning NOTES
Contact the Service
Center once a year to
clean the internal
parts of the projector.
Accumulated dust can
cause mechanical failure.
When cleaning the plastic parts such as projector case, unplug the power and
wipe it with a soft cloth. Do not use cleanser, spray water or wipe with a wet
cloth. Especially, never use cleanser (glass cleaner), automobile or industrial
shiner, abrasive or wax, benzene, alcohol etc., which can damage the product.
Use an air spray or soft cloth that is moist with a neutral detergent and water
for removing dust or stains on the projection lens.
It can cause fire, electric shock or product damage (deformation, corrosion and damage).
Others WARNING
Do not attempt to service the projector yourself. Contact your dealer or service center.
This may cause damage to the projector and could give an electric Shock as well as invalidating the warranty!
Others NOTES
Do not mix new batteries with old
batteries.
This may cause the batteries to overheat and leak.
Be sure to unplug if the projector is
not to be used for a long period.
Accumulated dust may cause a fire hazard or damage to the unit!
7
Only use the specified type
of battery.
This could cause damage to the
remote control.
Names of parts
Main Body
*
The projector is manufactured using high-precision technology. You may, however, see on the Projector
screen tiny black points and/or bright points (red, blue, or green). This can be a normal result of the
manufacturing process and does not always indicate a malfunction.
Names of parts
Control panel
Control Panel
Power button
Front remote control sensor
Zoom ring
Focus ring
Foot adjusting button
MENU Button
Selects or closes menus.
ġ2Ģ2˘2˚Button
Adjusts functions of menus.
AUTO Button
It automatically corrects the
position and the shaking of the
image at the RGB mode.
INPUT Button
Switches to RGB(Component), HDMI, Video
mode.
#
OK Button
Checks present mode and saves the
function changes.
POWER Button
Turn ON/OFF the projector.
8
Names of parts
Connecting Part
RGB OUT
Rear remote control sensor
RGB IN-2
Kensington Security
System Connector
(Refer to page 14)
AC IN
RGB IN-1
HDMI
VIDEO IN
IN
USB(SVC only)
RS-232C
LAN
9
Remote Control
Names of parts
⢮❺#ᴮ㍦
㛾ᬞ#ᶞ⢿#ᴮ㍦
㖞➸#∑㬉
㛿⠢/#ġ2Ģ2˘2˚ᴮ㍦
᳇#⤚⢿#ᴮ㍦
᳇#⤚⢿#ᴮ㍦
㛾ᬞ⢿⩪#ᴮ㍦
㛾ᬞ#ಪᩦ#ᴮ㍦
ㅪ⠞#ᴮ㍦
㛾ᬞㄖ#ᴮ㍦
⠯ᣏ⇊ㆇ#ᴮ㍦
ጞ#ᴮ㍦
῏⯵#⽷⼐#∑㬉
㢰⣲㧏#∑㬉
㖞㘫#ⳂⰦ#∑㬉
〤#∑㬉
Თ㶚#Όᥴ#∑㬉
⾗⵿#↕#∑㬉
⛑㷸#↕#∑㬉
Installing Batteries
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED WITH AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
• Open the battery compartment cover on the back of the remote control.
• Insert the specified type of batteries with correct polarity, match “+” with “+”, and
match “-” with “-”.
• Install two 1.5V AAA batteries. Don’t mix used batteries with new batteries.
10
Names of parts
Projector Status Indicators
* Lamp indicator, operation indicator and temperature indicator at the top of the projector show the user the operating status
of the projector.
Lamp Indicator
Operation Indicator
Lamp Indicator
Temperature Indicator
Red
Green(flashing)
Green
Orange(flashing)
Off
Orange
Red(flashing)
Red
Red(flashing)
Green(flashing)
Orange
Red
Red (flashing)
Temperature Indicator
Operation Indicator
Standby.
Lamp is starting up.
Unit is in operation (Lamp is turned on)
Projector lamp is cooling (20 sec.)
Power off.
Standby-This mode cools the projector naturally for 4
minutes after it is turned off.
This indicates a Colour Wheel problem.
Please contact your local service centre.
Projector lamp is reaching the end of its life and needs
to be replaced with a new lamp.
The projector is experiencing an error. Retry Power On
again later. If lamp indicator is red (flashing) again, contact the service center.
The lamp cover is open.
A high temperature state has been detected. Turn the
Projector off.
The Projector has turned off due to excessive heat.
Power has turned off due to problem with the internal
cooling fan. Contact your service center.
11
Accessories
Names of parts
Remote Control
Power Cord
AAA Battery
Computer Cable
Owner’s manual
Lens cap and Strap
ez-net Program CD
Optional Extras
* Contact your dealer to purchase these items.
* Contact your service personnel for replacing of lamp.
* The lamp is consumable and needs to be replaced with a new one when it is burned out.
* Optional parts can be changed without notice to improve the quality of the product, and new optional parts can be added.
Projection Screen
Component Cable
RCA to D-Sub Adapter
Lamp
HDMI Cable
Video Cable
LAN
Cable
RS-232C Cable
HDMI to DVI Cable
Ceiling installer for projector
12
Installing and Composition
Installing and Composition
Installation Instructions
*
Don’t place the projector in the following conditions. It may cause malfunction or product damage.
Provide proper ventilation for this projector.
The projector is equipped with ventilation holes(intake) on
the bottom and ventilation holes(exhaust) on the front. Do
not block or place anything near these holes, or internal
heat build-up may occur, causing picture degradation or
damage to the projector.
Never push projector or spill any kind of liquid into the
projector.
Place this projector in adequate temperature and humidity conditions.
Install this projector only in a location where adequate temperature and humidity is available. (refer p.41)
Don’t place the projector where it can be covered with dust.
This may cause overheating of the projector.
Do not place the projector on a carpet, rug or other
similar surface. It may prevent a adequate ventilation
of the projector bottom. This product should be
mounted to a wall or ceiling only.
Leave an adequate distance(30cm/12 inches or
more) around the projector.
Do not obstruct the slots and openings of the projector. This may cause overheating and create a fire hazard.
The projector is manufactured using high-precision technology. You may, however, see tiny black points and/or
bright points (red, blue, or green) that continuously appear on the projector Screen. This is a normal result of
the manufacturing process and does not indicate a malfunction.
To display DTV programs, it is necessary to purchase a DTV receiver (Set-top Box) and connect it to the projector.
When the remote control does not work during operation.
The remote control may not work when a lamp equipped with electronic ballast or a three-wavelength lamp is installed.
Replace those lamps with international standard products to use the remote control normally.
13
Installing and Composition
Basic Operation of the Projector
1. Place the projector on a sturdy and horizontal surface with the PC or AV source.
2. Place the projector with the desired distance from the screen. The distance between the projector and the screen
determines the actual size of the image.
3. Position the projector so that the lens is set at a right angle to the screen. If the projector is not set at a right angle,
the screen image will be crooked. If this is so then the keystone adjustment may correct this (Refer to page 27.).
4. Connect the cables of the projector to a wall power socket and other connected sources.
projection distance based on the picture format
Screen
Screen height (X)
Screen Width (Y)
X/2
X/2
Y/2
Y/2
Projection off-set ratio:100%
Projection distance (D)
Screen
Diagonal Size
(mm)
Projection distance (D)
4 : 3 Scale Projection Distance
Horizontal Size
(mm)
Vertical Size
(mm)
Wide Distance
(mm)
Tele Distance
(mm)
* The longest/shortest distance
show status when adjusted by
the zoom function.
14
Installing and Composition
Using Kensington Security System
*
The projector has a ‘Kensington’ Security System Connector on the side panel. Connect the ‘Kensington’
Security System cable as below.
*
For the detailed installation and use of the Kensington Security System, refer to the user’s guide attached
to the Kensington Security System set.
And for further information, contact http://www.kensington.com, the internet homepage of the
Kensington company that deals with expensive electronic equipment such as notebook PCs or projectors.
*
Kensington Security System is an optional item.
15
Installing and Composition
Turning on the Projector
1. Connect power cord correctly.
2. Remove the lens cap. If it is left on, it could become deformed due to the heat produced by
the projection lamp.
3. Press the POWER button on the remote control or top cover.
(Green operation indicator flashes if lamp is in start-up cycle.)
*
An image will appear after the operation indicator light turns (Green).
*
Select the source mode with the INPUT button.
* Do not disconnect the power cord during the suction/discharge fan in operation. If the power cord is disconnected during the
suction/ discharge fan in operation, it may takes longer to activate the lamp after turning on the power and the lifespan of the
lamp may be shortened.
Turning off the Projector
1. Press the POWER button on the top cover or remote control.
2. Press the POWER button on the top cover or remote control again to turn off the power.
3. If the operation indicator LED is orange and blinking, do not disconnect(20 sec.) the supply until the operation
indicator LED is lit constantly (orange).
* If the operation indicator LED is orange and blinking, the power button on the top cover or on the remote control will not operate.
* This projector features the Quick Power On/Off function that allows a user to turn it on and off quickly.
Power off?
Please press Power key again.
* What is the Quick Power On/Off function?
The projector enters into Standby mode without waiting it is cooled.
If Standby mode continues for a certain amount of time, the projector can operate without cooling when it is turned on.
16
Installing and Composition
Focus and Position of the Screen Image
When an image appears on the screen, check if it is in focus and fits well to the screen.
Focus ring
* To adjust the focus of the image, rotate the focus ring which is the outer ring on the lens.
* To adjust the size of the image, rotate the zoom ring which is the inner ring on the lens.
To raise or lower the image on the screen, extend or retract the foot at the bottom of the projector by
pushing foot adjusting button as below.
Zoom ring
Foot adjusting button
1. While pressing the foot adjusting button, raise or lower the projector to place the screen image in the proper position.
2. Release the button to lock the foot in its new position.
3. Turn the foot at the back left or right to make a fine tune of the length of the projector.
After raising the front foot, do not press down on the projector.
Selecting source mode
1. Press the INPUT button on the remote control or the control panel.
RGB1
RGB2
HDMI
Video
MENU Exit OK
2. After moving into desiring input by pressing
* When a signal cable is plugged in and there ’s a signal, the selecting item is activated as white,and if there ’s no signal,the selecting item
is deactivated as gray.
* If pressing the input selection button, it is possible to select activated item.
* It is possible to watch by selecting RGB 1 for Component 1 input and RGB 2 for Component 2 input, and in case of Component,
even though there ’s an input signal, the OSD item is not activated.
ġĢ
button, please press the confirm button.
17
Loading...