LG Electronics 47LY560H, 32LY560H, 42LY560H, 39LY560H User Manual

32LY560H 39LY560H

42LY560H

47LY560H

Lodging Guest Interactive Pro:Centric ® TVs

Commercial Mode Setup Guide

Note: Selected features shown in this guide may not be available on all models.

EXPERIENCED INSTALLER

EZ-Manager Wizard pages 12 – 18

Custom Master TV Setup pages 31 – 33

Cloning Procedures pages 34 – 37

P/N: 206-4258 (Rev A)

For Customer Support/Service, please call:

1-888-865-3026

The latest product information and documentation is available online at:

www.LGsolutions.com

MODEL and SERIAL NUMBER The model and serial numbers of this TV are located on the back of the cabinet. For future reference, LG suggests that you record those numbers here:

Model No._________________ Serial No._______________

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING:

TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USERSERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to

the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

POWER CORD POLARIZATION:

This product is equipped with a 3-wire grounding-type alternating current power plug. This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the 3-wire grounding-type plug.

NOTE TO CABLE/TV INSTALLER:

This reminder is provided to call the cable TV system installer’s attention to Article 820-40 of the National Electrical Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical.

REGULATORY INFORMATION:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

CAUTION:

Do not attempt to modify this product in any way without written authorization from LG Electronics U.S.A., Inc. Unauthorized modification could void the user’s authority to operate this product.

COMPLIANCE:

The responsible party for this product’s compliance is: LG Electronics U.S.A., Inc. 1000 Sylvan Avenue, Englewood Cliffs, NJ 07632, USA • Phone: 1-201-816-2000

Marketed and Distributed in the United States by LG Electronics U.S.A., Inc.

1000 Sylvan Avenue, Englewood Cliffs, NJ 07632

206-4258

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources, such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where it exits from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination in order to avoid injury from tip-over.

PORTABLE CART WARNING

13.

Refer all servicing to qualied service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

14. Never touch this apparatus or antenna during a thunder or

lightning storm.

15. When mounting a TV on the wall, make sure not to install the TV by the hanging power and signal cables on the back of the TV.

16. Do not allow an impact shock or any objects to fall into the product, and do not drop objects onto the screen.

17. Power Cord Caution: It is recommended that appliances be placed

upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the TV specifications.

Periodically examine the cord of your appliance, and if its

appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or mechanical abuse, such as twisting, kinking, or pinching or being closed in a door or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance.

Do not use a damaged or loose power cord. Be sure to grasp

the plug when unplugging the power cord. Do not pull on the power cord to unplug the TV.

18. Overloading Do not connect too many appliances to the same AC power

outlet as this could result in fire or electric shock. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in re or electric shock.

19. Outdoor Use/Wet Location Warning: To reduce the risk of re or electrical shock, do not expose this product to rain, moisture or other liquids.

Do not touch the TV with wet hands. Do not install this product

near ammable objects such as gasoline or candles or expose the TV to direct air conditioning.

Do not expose to dripping or splashing and do not place

objects lled with liquids, such as vases, cups, etc., on or over the apparatus (e.g., on shelves above the unit).

20. Grounding

Ensure that you connect the earth ground wire to prevent

possible electric shock (i.e., a TV with a three-prong grounded AC plug must be connected to a three-prong grounded AC outlet). If grounding methods are not possible, have a qualied electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightning rods, or gas pipes.

21. Disconnect Device

The mains plug is the disconnecting device. The plug must

remain readily operable.

As long as this unit is connected to the AC wall outlet, it is not

disconnected from the AC power source even if you turn off this unit by SWITCH.

(Continued on next page)

206-4258

IMPORTANT SAFETY INSTRUCTIONS

(Continued from previous page)

22. Outdoor Antenna Grounding If an outside antenna or cable system is connected to the

product, follow the precautions below.

An outdoor antenna system should not be located in the

vicinity of overhead power lines or other electric light or power circuits or where it can come into contact with such power lines or circuits as death or serious injury can occur.

Be sure the antenna system is grounded so as to provide

some protection against voltage surges and built-up static charges.

Article 810 of the National Electrical Code (NEC) in the U.S.A.

provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna-discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

Antenna Grounding According to NEC, ANSI/NFPA 70

Ground Clamp

Electric Service

Equipment

Antenna Lead in Wire

Antenna Discharge Unit (NEC Section 810-20)

Grounding Conductor (NEC Section 810-21)

Ground Clamps

Power Service Grounding Electrode System (NEC Art 250, Part H)

23. Cleaning When cleaning, unplug the power cord and wipe gently with

a soft cloth to prevent scratching. Do not spray water or other liquids directly on the TV as electric shock may occur. Do not clean with chemicals such as alcohol, thinners or benzene.

24. Transporting Product Make sure the TV is turned Off and unplugged and that all

cables have been removed. It may take two or more people to carry larger TVs. Do not press against or put stress on the front panel of the TV during transport.

25. Ventilation Install the TV where there is proper ventilation. Do not install

in a conned space such as a bookcase. Do not cover the TV with cloth or other materials (e.g., plastic) while it is plugged in. Do not install in excessively dusty places.

26. Do not touch the ventilation openings, as they may become

hot while the TV is operating.

27. If you smell smoke or other odors coming from the TV or

hear strange sounds, unplug the power cord, and contact an authorized service center.

28. Do not press against the front panel of the TV with your

hand or a sharp object (e.g., a nail, pencil, or pen) or make a scratch on it.

29. Keep the product away from direct sunlight.

30. Dot Defect

The LCD panel is a high technology product with resolution of two million to six million pixels. In a very few cases, you could see ne dots on the screen while you are viewing the TV. Those dots are deactivated pixels and do not affect the performance and reliability of the TV.

31. Generated Sound

“Cracking”: A cracking noise that occurs while the TV is On or when it is turned Off is generated by plastic thermal contraction due to temperature and humidity. This noise is common for products where thermal deformation is required.

Electrical circuit humming/panel buzzing: A low level noise is generated from a high-speed switching circuit, which supplies a large amount of current to operate a product. It varies depending on the product. This generated sound does not affect the performance and reliability of the product.

32. For LCD TV

If the TV feels cold to the touch, there may be a small “icker” when it is turned On. This is normal; there is nothing wrong with the TV. Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they have no adverse effect on the TV’s performance. Avoid touching the LCD screen or holding your nger(s) against it for long periods of time. Doing so may produce some temporary distortion effects on the screen.

206-4258

Table of Contents

Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . 3 – 4

Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Commercial Mode Overview . . . . . . . . . . . . . . . . . . . . . 6 – 9

Setup Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Pass-through Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

FTG Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Determining the TV Operating Mode . . . . . . . . . . . . . . . . 9

Pro:Centric Operation . . . . . . . . . . . . . . . . . . . . . . . . 10 – 11

Pro:Centric Interactive Menu Features. . . . . . . . . . . . . . 10

Pro:Centric Interactive Menu Navigation . . . . . . . . . . . . 10

Pro:Centric Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

EZ-Manager Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Initiate Configuration or Exit the EZ-Manager Wizard . . 12

TV Configuration Options. . . . . . . . . . . . . . . . . . . . . . . . . . 13

Zone and Room Number Assignments . . . . . . . . . . . . . . 14

Configure Pro:Centric Settings . . . . . . . . . . . . . . . . . . . . 15

USB Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Ez Download Utility . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Accessing and Using the Ez Download Utility . . . . . . . . 19

Installer Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 – 30

Accessing the Installer Menu . . . . . . . . . . . . . . . . . . . . . 22

Using the Installer Menu. . . . . . . . . . . . . . . . . . . . . . . . . 23

Exiting the Installer Menu and Activating Settings . . . . . 23

Custom Master TV Setup. . . . . . . . . . . . . . . . . . . . . . 31

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Clonable TV Setup Menu Features . . . . . . . . . . . . . . . . 31

Custom Master TV Setup Procedure . . . . . . . . . . . . . . . 32

Cloning Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Learning Configuration from a Master TV . . . . . . . . . . . 34

Teaching Configuration to a Target TV . . . . . . . . . . . . . . 35

– 18

– 21

– 33

–

FTG File Manager Utilities Overview . . . . . . . . . . . . 38 – 43

Creating an FTG Configuration File . . . . . . . . . . . . . . . . 38

FTG File Manager Main Screen . . . . . . . . . . . . . . . . . . . 40

FTG Channel Map Configuration Utility . . . . . . . . . . . . . 41

FTG Channel Map Editor . . . . . . . . . . . . . . . . . . . . . . . . 42

FTG Installer Menu Configuration Utility. . . . . . . . . . . . . 43

IP Environment Setup . . . . . . . . . . . . . . . . . . . . . . . . 44 – 47

Accessing the IP Environment Menu . . . . . . . . . . . . . . . 44

Configuring the Network Connection . . . . . . . . . . . . . . . 44

Network Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Pro:Centric Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

References

Upgrading TV/PTC Software using a USB Memory

Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Downloading a Splash Screen using a USB Memory

Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Power Consumption Settings . . . . . . . . . . . . . . . . . . . . . . . 50

TV Aux Input Configuration . . . . . . . . . . . . . . . . . . . . . . . . 51

Auto Input(s) Sensing Feature . . . . . . . . . . . . . . . . . . . 52 – 53

RJP Model List & Input Auto-sensing Hierarchy . . . . . . . . 54

Restoring Factory Defaults on the TV(s) . . . . . . . . . . . . . . 55

Using the TV Zoning Feature . . . . . . . . . . . . . . . . . . . . 56 – 58

LY560H Rear and Side Jack Panels . . . . . . . . . . . . . . . . . 59

External Stereo Speaker Setup . . . . . . . . . . . . . . . . . . . . . 60

Installer Remote Control Typical Key Functions . . . . . . . . 61

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

General Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . 62

Commercial Mode Check . . . . . . . . . . . . . . . . . . . . . . . . 63

Glossary of Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Document Revision History / Open Source Software Notice 65

Back Cover. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

– 63

Notes

• Installer Menu content is intended for use primarily by qualied TV electronics technicians.

• Refer to the applicable Owner’s Manual for additional information on TV installation, specications, maintenance, and safety instructions.

• Design and specications subject to change without prior notice.

206-4258

Commercial Mode Overview

This document describes how to set up LY560H Pro:Centric ® TVs for Commercial Mode operation. LG commercial TV functionality is based on “ownership” of the Channel Map; that is, the Channel Map resides in the TV’s CPU or Protocol Translator Card (PTC) or it resides externally from the TV (i.e., in a device from the solution provider).

These TV models are capable of Free-To-Guest (FTG) Mode operation via the TV CPU. Alternatively, the TV can be configured for Pass-through Mode (default). When in Pass-through Mode, these TV models also allow external control via the TV’s MPI port.

Setup Checklist

Note: This document provides information specific to Commercial Mode operation. Refer to the Owner’s

Manual for information on TV installation and hardware and cable connections.

Installation

__ Unpack TV and all accessories. __ Install batteries in the Installer Remote. __ Install TV on VESA mount or stand. Note: It may be advisable to make all cable

connections before installing on VESA mount or stand, as appropriate.

Hardware Connections

__ Install any additional hardware as

appropriate to your institution, LAN, etc.

Cable Connections

__ Make all rear jack panel connections, as

appropriate.

Commercial Mode Setup

__ Complete appropriate procedures as described

in this document for Commercial Mode operation.

Pass-through Mode

This mode allows you to configure individual TVs for Pro:Centric and/or FTG Mode operation. This mode also allows external control via the MPI port on the TV rear jack panel.

There are two methods for configuring individual TVs that are currently in Pass-through Mode: either using the EZ-Manager Wizard or the Custom Master TV Setup procedure as described in this document.

EZ-Manager Wizard

When the TV is in a factory default state, the EZ-Manager Wizard provides automated or manual options for conguring essential items for Pro:Centric operation and also provides an option for using a USB memory device to congure the TV. Use the Installer Remote to make selections and complete each step. See “EZ-Manager Wizard” on pages 12 to 18 for detailed information.

Custom Master TV Setup

The Custom Master TV Setup procedure enables you to create a customized Master TV Setup for Pass-through Mode or FTG Mode configuration purposes. Use the Installer Remote to congure Installer Menu items as required for TV operation and set up TV features (Channel, Picture, Audio, etc.). See “Custom Master TV Setup” on pages 31 to 33 for detailed information.

206-4258

Installer Menu

To create a Master TV Setup, you will need to know how to access the commercial controller (PTC) Installer Menu and make changes to the default values as required. If necessary, familiarize yourself with the Installer Menu and how to make and save changes. Refer to pages 22 to 30 for information on accessing the Installer Menu and for detailed descriptions of the Installer Menu items.

TV Setup Menus

On-screen setup menus control the features of the TV. Use the Installer Remote to access the TV setup menus, and set the TV features to the desired configuration for the end user.

Cloning

Cloning refers to the process of capturing a Master TV Setup and transferring it to a Target TV. The Master TV’s clonable setup menu features should be configured as part of the Master TV Setup. If there are features in the Master TV’s setup—channel icons or labels, digital font options, etc.—that are not set or that are set incorrectly, those features also will not be set or will be set incorrectly in the Target TVs. Refer to pages 34 to 37 for detailed information on cloning requirements and procedures.

Commercial Mode Overview (Cont.)

xxLY560H PTC INSTALLER MENU

000 INSTALLER SEQ 000

UPN 000-000-000-000 ASIC D279 PTC V1.00.008 CPU V3.11.00

PICTURE

LOCK

CPU-CTV

Typical Installer Menu

AUDIO

OPTION

TV Setup Menus

CHANNEL

INPUT

TIME

MY MEDIA

External MPI Control

To control the TV using an external MPI control device, you must use the TV’s MPI port for communication purposes.

Note: These TV models are not equipped with MPI card slots.

FTG Mode

In this mode, the TV’s CPU is congured with an FTG Channel Map, and the CPU controls and restricts the tuning operation of the TV based on this FTG Channel Map. The FTG Channel Map enables the decryption of each Pro:Idiom ® encrypted channel and also provides logical channel mapping of physical RF channels (analog and digital) and Aux inputs. In addition, in these models, FTG Mode provides the option to select either logical or physical tuning during configuration (refer to “Teaching Configuration to a Target TV” on pages 35 to 37 and also see note below).

Note: Logical channel mapping of physical RF channels eliminates dash tuning (for example, physical 19-3 can be mapped to logical channel 9). Physical channel tuning requires that you include the dash when direct entering channel numbers.

206-4258

Commercial Mode Overview (Cont.)

FTG Mode Features

FTG Mode provides the following features:

• Logical or physical tuning of physical RF channels and Aux inputs.

• Mapping of RF channels with minor (program) numbers up to 999.

• FTG Channel Map of up to 600 channels.

• Start Channel set for RF or Aux input delivered content.

• Pro:Centric data delivery over RF or IP.

• TV Zoning option for location-specic conguration.

LG’s FTG File Manager PC software enables you to create an FTG Conguration (.tlx) le, which may be used to congure the CPU for FTG Mode. FTG File Manager utilities enable you to create/edit an FTG Channel Map and congure Installer Menu settings. You can also save (Learn) a TLX le from a Master TV.

In this mode, the TV’s CPU must be congured with an FTG Channel Map and FTG Installer Menu settings using one of the following processes:

• Local: Congure an individual LY560H TV via its USB port using a USB memory device / TLX le. The “Teach to TV (TLX)” process and associated procedures for FTG Mode conguration are described on pages 34 to 37.

• Remote: Congure all LY560H TVs at the site using a Pro:Centric server head end device (Example: PCS150R). Load a TLX le on the Pro:Centric server using the TV E-Z Installation “Conguration” option in the Pro:Centric server Admin Client. Refer to the Pro:Centric Server Admin Client User Guide for further information.

While the TV is in FTG Mode:

• Users can still access the Installer Menu using an LG Installer Remote; however, all Installer Menu items will be read-only.

• Any FTG conguration changes must be made using a TLX le (typically edited in the FTG File Manager). The FTG File Manager’s FTG Channel Map Conguration and FTG Installer Menu Conguration Utilities enable you to make changes, respectively, to the FTG Channel Map and FTG Installer Menu settings as necessary. See information on local conguration in this document or refer to documentation for the server for information on remote management.

• If it becomes necessary to restore the TV to Pass-through Mode, there are several options that will enable you to do so. See Reference section, “Restoring Factory Defaults on the TV(s),” for further information.

Pages 38 to 43 provide overviews of the utilities that comprise the FTG File Manager. Refer to the Free- To-Guest (FTG) File Manager User Guide for further information on the FTG File Manager.

Remote Management in FTG Mode

When the TV is configured for FTG Mode, remote management of the FTG Channel Map and FTG Installer Menu settings is provided by a Pro:Centric server, via a TLX file loaded on the Pro:Centric server Admin Client. Refer to the Pro:Centric Server Admin Client User Guide for further information.

206-4258

Commercial Mode Overview (Cont.)

Determining the TV Operating Mode

To determine the operating mode of the TV, press MENU SETTINGS on the Installer Remote. The menu displayed depends on the operating mode. See examples below.

If the Function Menu appears, the TV is in a mode (FTG, PPV, etc.) that does not allow the end user to change the fundamental TV setup. If the TV setup menus appear, the TV is in Pass-through Mode

Move

ASPECT RATIO

16:9

ABC

Just Scan

Set By Program

4:3

Zoom

PICTURE

LOCK

AUDIO

OPTION

CHANNEL

INPUT

Function Menu

Indicates the TV is not in Pass-through Mode . While the TV is in this mode, Installer Menu settings can be accessed as read-only.

TV Setup Menus

TIME

Shows that the TV is in Pass-through Mode .

MY MEDIA

206-4258

Pro:Centric Operation

Pro:Centric Interactive Menu Features

LG’s Pro:Centric application enables guests to locate and select television entertainment using an interactive channel guide, check the daily weather, and view hotel and surrounding amenities via custom billboards and points-of-interest maps.

Pro:Centric application features include:

• Portal and information screens/pages (including a “Welcome” page) that include branding logos.

• An optional customized user interface (custom “skins”).

• Billboards and points-of-interest maps that can be customized to focus on hotel amenities, local attractions and businesses, restaurants, news, events, etc.

• An optional Weather billboard that includes a local radar map, current conditions, and a four day forecast.

• An interactive channel guide that provides a channel list with channel icons. An electronic program guide (EPG) is an optional feature that displays up to three days of programming information viewable by channel and time.

• Video spooling that enables the hotel to deliver a video le to guest TVs for promotion and information purposes.

The Pro:Centric server Admin Client web editor/content wizard is provided for customer conguration of portal messages and billboards/maps.

Note: Customized content is typically dened by the service integrator and/or hotel administrators. LG does not provide hotel-specic content.

Pro:Centric Interactive Menu Navigation

An LG Pro:Centric-capable TV remote control provides access to both interactive menus and regular TV features. Press PORTAL on the remote to access the interactive menus.

Note: Interactive menu options may vary, depending on Pro:Centric features enabled for the site. The following are default interactive menus.

Channel Guide

Shows available TV networks and logical channels. When available, EPG data provides additional channel and program information.

Information

Typically displays information on hotel amenities, for example, restaurants, in-room dining, business centers, facilities, etc., as well as information on local weather and attractions.

Help

Provides help for navigating the interactive menus.

Watch TV

Removes the interactive menu from the screen and returns to the previously tuned TV channel.

206-4258

Pro:Centric Operation (Cont.)

Pro:Centric Setup

Administration and management options for the Pro:Centric server are described in detail in the Pro:Centric Server Admin Client User Guide. This document describes only those settings that must be specied on the TVs to enable Pro:Centric remote management and/or the Pro:Centric application.

• Remote management (TV E-Z Installation): The Pro:Centric server Admin Client provides remote management facilities for downloading splash screens and software/firmware updates as well as facilities for downloading FTG Channel Map and FTG Installer Menu settings for FTG Mode configuration.

• Pro:Centric application: The application, which operates in conjunction with FTG and PPV Modes, comprises the Pro:Centric interactive menus/features described on the previous page. Pro:Centric application settings are managed via the Pro:Centric server Admin Client.

The Pro:Centric server settings can be congured using one of the following methods:

• When the TV is in a factory default state, the EZ-Manager Wizard provides automated or manual options for conguring the Pro:Centric server settings.

The EZ-Manager Wizard also provides a USB conguration option that enables you to congure a TV for FTG Mode using a TLX le stored on a USB memory device. The TLX le incorporates FTG Installer Menu settings, which includes Installer Menu items 098 PRO:CENTRIC and 119 DATA CHANNEL.

Refer to “EZ-Manager Wizard” on pages 12 to 18 for further information on the EZ-Manager Wizard options.

• If the TV is in Pass-through Mode, either:

− Set Installer Menu items 098 PRO:CENTRIC and 119 DATA CHANNEL to the appropriate values. Refer to “Installer Menu” information on pages 22 to 30 for further details. Also, as necessary, refer to “Custom Master TV Setup” information on pages 31 to 33 and/or cloning information on pages 34 to 37.

− Congure the appropriate Pro:Centric server settings in the IP Environment / Pro:Centric Menu. You must use this option, in particular, if you wish to congure IP settings for the Pro:Centric server. See “Accessing the IP Environment Menu” on page 44 and “Pro:Centric Setup” on page 46 for further information.

Note: When the TV is in either Pass-through Mode or FTG Mode, you can also leave Installer Menu item 119 DATA CHANNEL set to its default value (255) to enable the TV’s Data Channel Auto Search feature to set the DATA CHANNEL value. See item 119 description on page 30 for additional information.

• If the TV is in FTG Mode, use the FTG File Manager to update the Pro:Centric and Data Channel Installer Menu items (along with their afliated elds). Then, transfer the FTG Installer Menu settings to the TV. Refer to the FTG Mode overview on pages 7 to 8 for further information on FTG Mode operation and conguration. Also, see note above regarding the option to use the TV’s Data Channel Auto Search feature to set the DATA CHANNEL value.

206-4258

EZ-Manager Wizard

The primary purpose of the EZ-Manager Wizard is to guide you through the process (automated or manual) of configuring the essential Installer Menu items for Pro:Centric operation. The wizard will appear on the screen each time the TV is turned ON, until one of its configuration methods has been completed or the wizard is exited. Use the Installer Remote to make selections and complete each wizard step.

While the EZ-Manager Wizard is intended primarily for Pro:Centric-related conguration, the wizard also offers Zoning as well as USB conguration options.

• LY560H TVs support the TV Zoning feature, which enables location-specic settings (see Reference section, “Using the TV Zoning Feature,” for further information). The EZ-Manager Wizard enables you to set the TV Zone # in the TV as part of the conguration process.

• The EZ-Manager Wizard enables you to redirect to the TV’s standard TV Manager / USB Download Menu as part of the conguration process, if desired, to perform USB conguration functions, including FTG Mode conguration, cloning, splash image downloads, and software upgrades.

Caution: Do NOT unplug the TV power cord or remove the antenna cable or, if applicable, the LAN cable during the conguration process, as doing so will interrupt the current step and may corrupt the conguration data.

Before You Begin

• If you plan to create a Master TV Setup using the procedure described on pages 31 to 33, be sure to exit the EZ-Manager Wizard in order to avoid setting modes that may restrict the custom setup procedure. See also “Initiate Conguration or Exit the EZ-Manager Wizard” below.

• If it has been completed or exited and therefore does not display, the EZ-Manager Wizard can be reactivated; however, this requires that you perform an “IN-STOP” to restore factory defaults on the TV(s). See Reference section, “Restoring Factory Defaults on the TV(s),” for further information.

• Each wizard step is allotted a time frame after which the wizard proceeds without user interaction. If the Pro:Centric server is congured on the system and if no location-specic settings are required in the TV, for example, for TV Zone, Label, and/or Room Number settings, you can simply turn ON the TV, and once initiated, the wizard will proceed through each of the conguration steps with no further user interaction.

• If any of the conguration steps fails, you will see a “Diagnostics” screen with an indication of the failure. You will then have the opportunity to reinitiate the conguration process from the previous screen or exit the EZ-Manager Wizard.

Initiate Conguration or Exit the EZ-Manager Wizard

The Welcome screen provides a brief introduction to the EZ-Manager wizard.

EZ-Manager Wizard

Welcome to LG’s EZ-Manager Wizard

• Use this setup wizard to congure the TV for Pro:Centric and/or FreeTo-Guest (FTG) operation.

Select ‘Next’ to continue.

• If a Pro:Centric Server will not be installed and/or you do not wish to use the wizard to congure this TV for FTG Mode, you may exit the wizard.

Select ‘No Pro:Centric’ to disable the Pro:Centric feature of this TV, or select ‘Exit’ to quit.

This setup wizard will start automatically in 10 seconds.

No Pro:Centric

Exit

Note: If there is no user action in this screen within 10 seconds, the wizard will proceed to the rst conguration step. Once the wizard has proceeded, it is not possible to return to the Welcome screen; however, if you simply wish to exit the wizard, you can do so by selecting the “Exit” option from the subsequent screen(s).

206-4258

EZ-Manager Wizard (Cont.)

From the Welcome screen, you have the following options:

• To proceed with the EZ-Manager Wizard, use the arrow keys on the Installer Remote to select/

highlight Next and press OK. Then, continue to the “TV Conguration Options” section below.

• To exit the wizard, but retain the use of the Pro:Centric remote management feature on this TV (i.e., Installer Menu item 119 DATA CHANNEL set to 255) in the future, use the arrow keys on the Installer Remote to select/highlight Exit and press OK. In the conrmation pop-up window, select OK, and then press OK once more on the Installer Remote.

• If you do not intend to install a Pro:Centric server on this system and you do not wish to use the wizard’s Zoning or USB conguration options, exit the wizard as follows: Use the arrow keys on the Installer Remote to select/highlight the No Pro:Centric option. This will disable the Pro:Centric feature of this TV (i.e., Installer Menu item 119 DATA CHANNEL will be set to 0). In the conrmation pop-up window, select OK, and then press OK once more on the Installer Remote.

TV Conguration Options

From the TV Conguration Options screen, you can choose how to proceed with the conguration of this TV (assuming you do not opt to exit the wizard, which you may also do at any time).

Note: If you intend to use the Zoning feature on the TV for location-specic conguration purposes, select the “Zone & Room Number” option from this screen and assign the appropriate TV Zone # in the TV BEFORE you continue with additional conguration.

EZ-Manager Wizard

Exit

TV Configuration Options

• To congure the TV for Pro:Centric operation, select ‘Next’.

• To set the optional Zoning feature, select ‘Zone & Room Number’.

• To access the TV’s USB Download Menu, select ‘USB Conguration’.

This setup wizard will continue automatically in 60 seconds.

USB Configuration

Zone & Room Number

Note: If there is no user action in this screen within one minute, the wizard will automatically continue to the next conguration step.

Use the Left/Right arrow keys on the Installer Remote to navigate between options on this screen. Each time you select/highlight one of the following options, the screen text and elds will change in accordance with your selection.

• To continue with Pro:Centric conguration, select Next (default) and press OK on the Installer Remote. Refer to “Congure Pro:Centric Settings” on pages 15 to 16 for additional information.

• Select Zone & Room Number to set the Zoning feature on this TV. See “Zone and Room Number Assignments” on the following page for further information.

• Select USB Conguration to access the TV Manager / USB Download Menu. See “USB Conguration” on pages 17 to 18 for further information.

Note: If you choose to exit the EZ-Manager Wizard from this point on, you will have the option to save any settings made by selecting Save and Exit in the exit conrmation pop-up window. Or, you can exit the wizard without saving any settings by simply selecting OK in the conrmation pop-up window.

206-4258

EZ-Manager Wizard (Cont.)

Zone and Room Number Assignments

You may complete one or more of the elds in the Zone, Label, and Room Number screen or leave them at their default settings (Zone) or blank (Label and Room Number), as desired; however, if you intend to use the Zoning feature on this TV, you MUST specify the appropriate value in the Zone eld as described below. See also Reference section, “Using the TV Zoning Feature,” for further information.

Note: The Zoning feature is only applicable for TVs that will be congured using a TLX le (local or remote conguration).

EZ-Manager Wizard

•

If creating Zones for Installer Menu settings and/or Channel Mapping, select the appropriate Zone # (0-8) based on the Zone in which this TV is installed. (See Commercial Mode Setup Guide for more information.)

• Select a Label and/or use the alphanumeric keypad on the remote to input the Room Number.

• When done, select ‘Next’ to continue.

Zone

Exit

Zone, Label, and Room Number

-----

USB Configuration

Room NumberLabel

Zone & Room Number

Q.MENU

INPUT

DVD

MARK

.,;

abc def

1 2 3

5 6

ghi jkl mno

4 5 6

pqrs tuv wxyz

7 809

CHAR/

NUM

FLASHBK

CHAR/NUM

P A

TIMER

CHVOL

DELETE

DEL

MUTE

PORTAL

INFO

GUIDE

1. Complete the appropriate eld(s) as described below. Use the Left/Right arrow keys on the

Installer Remote to navigate between each of the elds.

• Zone: Enables you to set a TV Zone # so that the TV can be congured with Installer Menu and/or TV Setup Menu settings intended only for the assigned Zone. The Installer Menu and/or TV Setup Menu settings may be provided in a TLX le to be used for conguration. If the TV is being congured for FTG Mode, the TV Zone # setting also allows the TV to omit channels that have been restricted in the FTG Channel Map.

To change the TV Zone from its default value (0), navigate to the Zone eld at the left of the screen, and use the Up/Down arrow keys to specify the desired TV Zone # (1–8).

• Label: Allows you to select a North, South, East, or West text label for this TV. In the Label eld, use the Up/Down arrow keys to select the applicable label.

• Room Number: Allows you to specify the number of the room in which the TV is located. In the Room Number eld, you can use the number keys on the Installer Remote to direct enter a room number. Use the Dash key on the Installer Remote as necessary to toggle between number and letter characters in the Room Number eld. Also, you can use the Flashback key on the Installer Remote to delete characters in this eld.

2. When you are ready to continue, select the appropriate option, as follows:

• To proceed to the next EZ-Manager screen, use the arrow keys to select Next, and then press OK on the Installer Remote. Continue to the “Congure Pro:Centric Settings” section on the following page.

• If you wish to use a USB memory device in conjunction with the TV Manager / USB Download Menu to complete the conguration, continue to “USB Conguration” on pages 17 to 18.

206-4258

Congure Pro:Centric Settings

Once you select “Next” from the TV Conguration Options screen, the Searching for Pro:Centric Server screen is displayed (see example at right), and you have the following options:

• You can allow the EZ-Manager Wizard to proceed with a series of automated steps to congure the TV for Pro:Centric operation and then to look for the Pro:Centric application and maintenance (E-Z Installation) les to download. In this case, the wizard uses a search algorithm to determine the Data Channel and the Pro:Centric Application Mode to set in the TV.

Continue with the “Automated Pro:Centric Conguration” subsection below.

• If you already know the settings (i.e., Data Channel and Pro:Centric Application Mode) that need to be congured in order for the TV to connect to the Pro:Centric server and/or if the Pro:Centric server is not yet installed, you may expedite the setup process by entering this data manually.

Continue with the “Manual Pro:Centric Conguration” subsection on the following page.

EZ-Manager Wizard (Cont.)

EZ-Manager Wizard

Note: You can select the “Back” button, where available, to check previous settings, as necessary.

Searching for Pro:Centric Server...

It may take 1 min 32 second(s).

This step automatically searches for the Pro:Centric server.

If there is no Pro:Centric Server installed, you do not need to continue with this procedure. Please select either ‘Exit’ or ‘Manual Pro:Centric’.

Status : Tuning channel 49

TV is now searching all of the channels for the data channel...

Back

Exit

Manual Pro:Centric

Automated Pro:Centric Conguration

Note: If the server is not yet congured on the system, use the

manual conguration option to congure the Pro:Centric operation.

Once the RF channel used by the Pro:Centric server as its data channel is found (the Pro:Centric Server Was Found screen will be displayed—see example at right) and the Pro:Centric Application Mode is determined, the wizard will advance to the Processing the Pro:Centric Conguration screen, which shows the progress of the data downloads. Note that some steps may require a few minutes.

If the process is successful, no further user interaction is required, though, in some instances, where the option (for example “Next”) is available, you may manually move forward to subsequent steps within the wizard to speed up the process.

Note: If, after completing the search, the TV is unable to nd a Pro:Centric server’s RF channel (while the Searching for Pro:Centric Server screen is on display), the wizard will stop and show a Diagnostics screen that enables you to manually return to the previous screen (to reinitiate the conguration) or exit the wizard.

When the Pro:Centric Conguration is complete, an EZ-Manager Conguration Complete screen is displayed, and after 10 seconds, the wizard exits, and the TV turns OFF.

Note: With the EZ-Manager Conguration Complete screen on display, you can also manually turn off or reboot the TV. If desired, select Turn Off or Reboot, respectively, and then press OK on the Installer Remote.

EZ-Manager Wizard

Pro:Centric Server was found...

It may take 2 second(s).

The Pro:Centric data channel was found!! (Data Channel: 75, Mode: GEM) The Download window will open in 2 second(s). You may wait or select ‘Next’. Otherwise, if you select ‘Exit’, the Pro:Centric server settings can be retained and used during the next download by selecting ‘Save & Exit’ in the Exit window.

Status : Tuning channel 75

The Pro:Centric data channel is found!! (Data Channel: 75, Mode: GEM)

Back

Processing the Pro:Centric Configuration...

Downloading the maintenance files takes several minutes.

Application files

Maintenance files

– Updating Configuration File

Warning - Do not remove AC power or the signal cables during these steps

Exit

Please wait...

Retrieving files from data channel 75

EZ-Manager Configuration Complete

The TV will turn off in 3 second(s).

Installed Components

Pro:Centric Application Maintenance Files

Reboot

GEM application downloaded

GEM app downloaded

In progress...

LY560H_Config.tlx

Turn Off

20%

206-4258

EZ-Manager Wizard (Cont.)

Manual Pro:Centric Conguration

1. With the Searching for Pro:Centric Server screen on display,

use the arrow keys on the Installer Remote to select/highlight the Manual Pro:Centric option at the bottom right of the screen, and press OK.

In the Pro:Centric Manual Conguration screen (see examples

at right below), you will be able to congure the appropriate Pro:Centric settings in the TV. Use the Up/Down arrow keys on the Installer Remote to navigate between elds.

2. In the Pro:Centric Mode eld, use the Left/Right arrow keys

to select the appropriate Pro:Centric Application Mode— GEM, FLASH, or Conguration Only.

Note: For remote management only, select “Conguration Only.” The TV will search for TV E-Z Installation data downloads; however, Pro:Centric application data will not be downloaded, i.e., Installer Menu item 098 PRO:CENTRIC will be set to 0.

3. Refer to the appropriate subsection below, depending on the

Pro:Centric server conguration, to complete the remaining elds.

RF Conguration

a) In the Media Type eld, use the Left/Right arrow keys to

select RF.

b) In the Data Channel eld, either key in or use the Left/

Right arrow keys to select the RF channel number that will be used by the Pro:Centric server as its data channel. The Data Channel value can be set from 1 to 135. *

IP Conguration

a) In the Media Type eld, use the Left/Right arrow keys to

select IP.

Note: By default, the Pro:Centric Manual Conguration screen initially shows RF conguration elds. When you select “IP” as the Media Type, the Data Channel and Signal Strength elds are replaced with (IP) Address and Port elds.

b) In the Address and Port elds, either key in or use the

Left/Right arrow keys to select the appropriate values for the Pro:Centric server IP address and port number.

The IP address must match the IPv4 multicast address and the port number must match the port number that is set in the Pro:Centric server.

EZ-Manager Wizard

Searching for Pro:Centric Server...

It may take 1 min 32 second(s).

This step automatically searches for the Pro:Centric server.

If there is no Pro:Centric Server installed, you do not need to continue with this procedure. Please select either ‘Exit’ or ‘Manual Pro:Centric’.

Status : Tuning channel 49

TV is now searching all of the channels for the data channel...

Back

EZ-Manager Wizard

Exit

Manual Pro:Centric

Pro:Centric Manual Configuration

Pro:Centric Mode

Media Type

Data Channel

Signal Strength Signal Quality

Back

GEM

< >

No signal

Exit

Pro:Centric Manual Configuration Screen with

RF Media Fields

EZ-Manager Wizard

Pro:Centric Manual Configuration

Pro:Centric Mode

Media Type

Addresss

Port

Back

GEM

< >

255

Exit

Pro:Centric Manual Configuration Screen with

IP Media Fields

255255255

* PCS150R and later Pro:Centric servers do not support HRC or IRC cable channel frequencies.

206-4258

(Continued from previous page)

EZ-Manager Wizard (Cont.)

4. Once all elds are completed as required, you have two

options (see also note below):

• To save the data entered and exit the wizard, use the arrow

keys to select Exit and then press OK. In the subsequent pop-up conrmation window, select Save and Exit, and then press OK once more. The Pro:Centric application and/or E-Z Installation data will be downloaded to the TV at a later time. This option is useful, in particular, if the Pro:Centric server has not yet been congured.

• To initiate a real-time download of Pro:Centric application and/or E-Z Installation data, use the arrow keys to select Next, and then press OK.

The EZ-Manager Wizard will proceed with the remaining Pro:Centric application and/or E-Z Installation data download steps, as shown on the Processing the Pro:Centric Conguration screen.

Note: With RF conguration, Pro:Centric server data must be present on the RF channel selected as the TV’s Data Channel in order for you to select “Next” (you will see a “Data Channel found” message below the signal strength indicator). With IP conguration, Pro:Centric server data must be present via the wired LAN cable connection in order for you to select “Next” (you will see a “IP server found” message below the Port eld).

When the Pro:Centric conguration is complete, an EZ-Manager Conguration Complete screen is displayed, and after 10 seconds, the wizard exits, and the TV turns OFF.

Note: With the EZ-Manager Conguration Complete screen on display, you also have the option to manually turn off or reboot the TV. If desired, select Turn Off or Reboot, respectively, and then press OK on the Installer Remote.

EZ-Manager Wizard

Pro:Centric Manual Configuration

Are you sure you want to exit the wizard?

Pro:Centric Mode

If you select ‘OK’ now, your settings will be lost

< >

and you will exit the setup wizard.

Channel Number

This window will close and you will be returned to

Signal Strength

the previous page automatically in 2 seconds.

Signal Quality

Save and Exit

Back

Processing the Pro:Centric Configuration...

Downloading the Pro:Centric application files takes a few minutes.

Retrieving files from data channel 75

Application files

Maintenance files

Warning - Do not remove AC power or the signal cables during these steps

Exit

Please wait...

EZ-Manager Configuration Complete

The TV will turn off in 3 second(s).

Installed Components

Pro:Centric Application Maintenance Files

Reboot

GEM

Cancel

No signal

In progress...

Pending...

GEM application downloaded

LY560H_Config.tlx

Turn Off

USB Conguration

The TV Manager / USB Download Menu provides options that enable you to download individual conguration or software les to the TV, or you can use the Ez Download utility available from the menu to select and download multiple conguration or software les at one time.

Each of the TV Manager / USB Download Menu functions requires that you have the appropriate le(s) loaded on a USB memory device. If you wish to perform a software upgrade or download a splash image from the TV Manager / USB Download Menu, the software upgrade/image le(s) must be stored in a folder named “LG_DTV” in the root directory of the USB memory device. TLX les should simply be stored in the root directory of the USB device.

206-4258

EZ-Manager Wizard (Cont.)

The procedure below assumes that the desired le(s) is/are already loaded onto the USB device. For further information on TV Manager / USB Download Menu functions and le requirements, and/ or for information on creating TLX les, refer to the appropriate section(s) in this document.

Before You Begin

• Ensure the USB device to be used has been formatted with FAT format.

• If you intend to use the Zoning feature on this TV, make sure to assign the appropriate TV Zone # in the EZ-Manager’s Zone, Label, and Room Number screen BEFORE continuing with USB Conguration. See “TV Conguration Options” on page 13 for further information.

• Refer to “Ez Download Utility” on pages 19 to 21 for further information on the Ez Download utility.

• Refer to “Custom Master TV Setup” on pages 31 to 33 for information on creating a TLX file for cloning purposes, and/or refer to “Creating an FTG Conguration File” on pages 38 to 39 for information on creating a FTG Conguration (.tlx) le for FTG Mode conguration.

• See Reference section, “Downloading a Splash Screen using a USB Memory Device,” for splash screen image guidelines.

• See Reference section, “Upgrading TV/PTC Software using a USB Memory Device,” for further information on software upgrades.

USB Conguration via EZ-Manager Wizard

With either the TV Conguration Options or the Zone, Label, and Room Number screen on display, proceed as follows to congure the TV using the USB memory device.

1. Insert the USB memory device that contains the appropriate le(s) into the TV’s USB port.

2. Use the arrow keys on the Installer Remote to select USB Conguration, and then press OK.

You will be redirected to the TV’s TV Manager / USB Download Menu:

TV Manager

USB

Diagnostics

Ez Download

Logo Image Download

Upgrade TV Software

Upgrade PTC Software

Teach To TV (TLX)

Note: You can press on the Installer Remote at any time to return to the EZ-Manager Wizard.

3. Select the appropriate option from the TV Manager / USB Download Menu, and complete the

download(s) as required.

Note: If you perform a software upgrade from the TV Manager / USB Download Menu, the TV will complete the upgrade and then reboot. Upon restart, the TV will display the EZ-Manager TV Configuration Options screen. If desired, you can re-access the TV Manager / USB Download Menu (to perform additional functions), proceed with conguration via the wizard, or exit the wizard.

4. Remove the USB memory device, and verify that the appropriate configuration is resident on

the TV.

206-4258

Ez Download Utility

The Ez Download utilty, available from the TV Manager / USB Download Menu, enables you to select multiple les at one time from the les loaded on a USB memory device. You may use this utility to download any one or all of the following to a TV: a TLX le for conguration purposes, a TV CPU or PTC software update, a splash screen image.

Before You Begin

• Ensure the USB device has been formatted with FAT format.

• Software upgrade and splash image les must be stored in a folder named “LG_DTV” in the root directory of the USB memory device. TLX les should simply be stored in the root directory of the USB device.

• If the EZ-Manager Wizard appears on the screen when you turn ON the TV, you can use the wizard’s “USB Conguration” option to access the Ez Download utility (see “TV Conguration Options” and/or “USB Conguration” on pages 13 and 17, respectively, as necessary).

• If the TV is currently in Pass-through Mode and you intend to use the TV Zoning feature for location-specic conguration purposes, make sure to assign the appropriate TV Zone # in the TV when directed to do so in the procedure below.

• Refer to “Custom Master TV Setup” on pages 31 to 33 for information on creating a TLX file for cloning purposes, and/or refer to “Creating an FTG Conguration File” on pages 38 to 39 for information on creating an FTG Conguration (.tlx) le for FTG Mode conguration.

• See Reference section, “Downloading a Splash Screen using a USB Memory Device,” for splash screen image guidelines.

• See Reference section, “Upgrading TV/PTC Software using a USB Memory Device,” for further information on software upgrades.

Caution: Do not unplug the TV power cord or remove the USB memory device during a data download, as doing so may cause the TV to malfunction or harm the USB device, respectively.

Accessing and Using the Ez Download Utility

1. If it is not ON already, turn ON the TV.

2. The next step depends on whether the EZ-Manager Wizard appears on the screen when you

turn ON the TV:

• If the wizard is displayed, you can complete the Ez Download via the wizard, as indicated above (see “Before You Begin”). However, to continue with this procedure and access Ez Download from the TV menus, exit the wizard. Then, continue with step 3.

• If the wizard is not displayed, go directly to step 3.

3. If the TV is currently in Pass-through Mode, you are transferring (Teaching) a TLX le to the TV as part of the Ez Download, and you intend to use the TV Zoning feature, assign the appropriate TV Zone # in the TV at this time. See Reference section, “Using the TV Zoning Feature,” for further information.

Note: In order for the proper location-specic TV Zone prole data to be applied, the Zone designation must be assigned in the Target TV(s) BEFORE you continue with Ez Download.

(Continued on next page)

206-4258

Ez Download Utility (Cont.)

(Continued from previous page)

4. Insert the USB memory device that contains the appropriate le(s) into the TV’s USB port.

5. To access the TV Manager / USB Download Menu from the TV menus:

• Press MENU SETTINGS on the Installer Remote to display the TV

setup menus (TV is in Pass-through Mode) or the Function Menu (TV is not in Pass-through Mode).

• Use the arrow navigation keys to select/highlight either the Option

menu icon from the TV setup menus or the Lock menu icon from the Function Menu. Then, press the number “7” key a total of seven times.

6. With the TV Manager / USB Download Menu on display (see example at right), use the Up/Down arrow keys to select Ez Download, and then press OK.

7. The Ez Download window contains a listing of the CPU (EPK), PTC, and splash image (LOGO) les stored in the LG_DTV folder and the TLX les stored in the root directory on the USB device.

To select or de-select a le, respectively, use the Up/Down arrows on

the Installer Remote to highlight the lename, and press OK to add or remove the checkmark at the left of the lename.

Note: The utility will only allow you to select one of each le type for

downloading. For example, if there are two TLX les in the Ez Download list, you can only select one or the other of those two les.

Note: After an Ez Download is run, a le is created on the USB device,

which maintains a history of the les previously used for Ez Download. The next time(s) you use this USB device for Ez Download, the les you selected for the previous download will be pre-selected by default.

8. The elds at the right of the screen will change depending on the currently highlighted le. Select the appropriate option(s) for each le, as applicable:

• For software and splash image les: The elds at the right of the

screen show the TV software versions and any available Forced Update options. Do not select any Forced Update options unless you have been specically instructed to do so or have previous experience with Expert Software Updates.

• For TLX les: If an FTG Channel Map is included in the TLX le, a

Channel Tuning / Channel Banner Display eld at the right of the screen enables you to select the format for the channel tuning/banner display. Press the green button on the Installer Remote to select Logical tuning, or press the yellow button on the Installer Remote to select Physical tuning. A checkmark will appear at the left of the selected option. Logical tuning is selected by default.

Note: If a TLX le does not include an FTG Channel Map, the

message, “No Channel Map in TLX le,” will be displayed at the right of the screen.

TV Manager

USB

Diagnostics

Ez Download

Logo Image Download

Upgrade TV Software

Upgrade PTC Software

Teach To TV (TLX)

Note: TV Manager / Diagnostics

is for service use only.

Ez Download

[TLX] xxLY560H-UA00001.TLX

[LOGO] Splash Image 1920 X 1080 Pro

[EPK] xxLY560H_V03_11_USB.epk

Updating EPK File... 50 %

Do not remove the USB from the port! Do not unplug!

xxLY560H-UA00001.tlx Splash Image1920 x 1080 ProC.jpg

xxLY560H_V03.11_USB.epk

(Continued on next page)

[ TV Software Version ] Current : 03.09.00.01 (CPU)

1.00.008 (PTC) EPK : 03.11.00.01

[ Forced Update Option ] SPI Boot LG Boot Logo

Apply

206-4258

+ 46 hidden pages