LG 43UH610N User Manual
Please read this manual carefully before operating your set and
retain it for future reference.
*MFL69361129*
www.lg.com
P/NO : MFL69361129(1605-REV00)
Printed in Korea
Safety and Reference
OWNER’S MANUAL
LED Monitor*
* LG LED Monitors applies LCD Monitors
with LED backlights.
2
ENGLISH
Safety instructions
Please read these safety precautions
carefully before using the product.
WARNING
Do not place the monitor and/or remote control
in the following environments:
tA location exposed to direct sunlight
tAn area with high humidity such as a
bathroom
tNear any heat source such as stoves and
other devices that produce heat
tNear kitchen counters or humidiers where
they can easily be exposed to steam or oil
tAn area exposed to rain or wind
tNear containers of water such as vases
Otherwise, this may result in re, electric
shock, malfunction or product deformation.
Do not place the product where it might be
exposed to dust. This may cause a re hazard.
Mains Plug is the monitor connecting/
disconnecting device to AC mains electric
supply. This plug must remain readily attached
and operable when monitor is in use.
Do not touch the power plug with wet hands.
Additionally, if the cord pin is wet or covered
with dust, dry the power plug completely or
wipe dust o. You may be electrocuted due to
excess moisture.
Make sure to connect Mains cable to compliant
AC mains socket with Grounded earth pin.
(Except for devices which are not grounded
on earth.) Otherwise possibility you may be
electrocuted or injured.
Insert power cable plug completely into wall
socket otherwise if not secured completely into
socket, re ignition may break out.
Ensure the power cord does not come into
contact with hot objects such as a heater. This
may cause a re or an electric shock hazard.
Do not place a heavy object, or the product
itself, on power cables.
Otherwise, this may result in re or electric
shock.
ENGLISH
3
When mounting monitor onto wall make sure
to neatly install and isolate cabling from rear of
monitor as to not create possibility of electric
shock /re hazard.
Do not plug too many electrical devices into a
single multiple electrical outlet. Otherwise, this
may result in re due to over-heating.
Do not drop the product or let it fall over when
connecting external devices. Otherwise, this
may result in injury or damage to the product.
Keep the anti-moisture packing material or
vinyl packing out of the reach of children.
Anti-moisture material is harmful if
swallowed. If swallowed by mistake, force
the patient to vomit and visit the nearest
hospital. Additionally, vinyl packing can cause
suocation. Keep it out of the reach of children.
Do not let your children climb or cling onto the
monitor.
Otherwise, the monitor may fall over, which
may cause serious injury.
Dispose of used batteries carefully to ensure
that a small child does not consume them.
Please seek Doctor- Medical Attention
immediately if child consumes batteries.
Do not insert any metal objects/conductors
(like a metal chopstick/cutlery/screwdriver)
between power cable plug and input Wall
Socket while it is connected to the input
terminal on the wall. Additionally, do not touch
the power cable right after plugging into the
wall input terminal. You may be electrocuted.
(Depending on model)
Do not put or store inammable substances
near the product. There is a danger of
combustion/explosion or re due to careless
handling of the inammable substances.
4
ENGLISH
Do not drop metallic objects such as coins,
hair pins, chopsticks or wire into the product,
or inammable objects such as paper and
matches. Children must pay particular
attention. Electrical shock, re or injury can
occur. If a foreign object is dropped into the
product, unplug the power cord and contact the
service centre.
Do not spray water on the product or scrub
with an inammable substance (thinner or
benzene). Fire or electric shock accident can
occur.
Do not allow any impact, shock or any objects
to fall into the unit, and do not drop anything
onto the screen. You may be injured or the
product can be damaged.
Never touch this product during a thunder or
lighting storm. You may be electrocuted.
Never touch the wall outlet when there
is leakage of gas, open the windows and
ventilate. It may cause a re or a burn by a
spark.
Do not disassemble, repair or modify the
product at your own discretion. Fire or electric
shock accident can occur.
Contact the service centre for check, calibration
or repair.
If any of the following occur, unplug the
product immediately and contact your local
service centre.
tThe product has been impacted by shock
tThe product has been damaged
tForeign objects have entered the product
tThe product produced smoke or a strange
smell
This may result in re or electric shock.
Unplug the monitor from AC mains wall socket
if you do not intend to use the monitor for a
long period of time. Accumulated dust can
cause re hazard and insulation deterioration
can cause electric leakage/shock/re.
Apparatus shall not be exposed to dripping or
splashing and no objects lled with liquids,
such as vases, shall be placed on the apparatus.
ENGLISH
5
Do not install this product on a wall if it could
be exposed to oil or oil mist. This may damage
the product and cause it to fall.
If water enters or comes into contact with
monitor, power cord please disconnect
the power cord and contact service centre
immediately. Otherwise, this may result in
electric shock or re.
Only use an authorized power cord approved
by LG Electronics. Otherwise, this may result
in re, electric shock, malfunction or product
deformation.
Never Disassemble the power cord. This may
result in re or electric shock.
Make sure the power cord is connected securely
to the power plug on the monitor. (Depending
on model)
CAUTION
Do not install the product on places such as
unstable shelves or inclined surfaces. Also avoid
places where there is vibration or where the
product cannot be fully supported. Otherwise,
the product may fall or ip over, which may
cause injury or damage to the product.
If you install the monitor on a stand, you need
to take actions to prevent the product from
overturning. Otherwise, the product may fall
over, which may cause injury.
If you intend to mount the product to a wall,
attach VESA standard mounting interface
(optional parts) to the back of the product.
When you install the set to use the wall
mounting bracket (optional parts), x it
carefully so as not to drop.
Only use the attachments / accessories specied
by the manufacturer.
We recommend that you maintain a distance
of at least 2 to 7 times the diagonal screen size
when watching monitor. If you watch monitor
for a long period of time, this may cause blurred
vision.
Only use the specied type of battery. This could
cause damage to the remote control.
Do not mix new batteries with old batteries.
This may cause the batteries to overheat and
leak.
6
ENGLISH
Batteries should not be exposed to excessive
heat. For example, keep away from direct
Sunlight, open replace and electric heaters.
Do not place non-rechargeable batteries in
charging device.
Make sure there are no objects between the
remote control and its sensor.
Signal from Remote Control can be interrupted
due to external/internal lighting eg Sunlight,
uorescent lighting. If this occurs turn o
lighting or darken viewing area.
When connecting external devices such as
video game consoles, make sure the connecting
cables are long enough. Otherwise, the product
may fall over, which may cause injury or
damage the product.
Do not turn the product On/O by pluggingin or unplugging the power plug to the wall
outlet. (Do not use the power plug for switch.)
It may cause mechanical failure or could give an
electric shock.
Please follow the installation instructions
below to prevent the product from overheating.
tThe distance between the product and the
wall should be more than 10cm.
tDo not install the product in a place with
no ventilation (e.g., on a bookshelf or in a
cupboard).
tDo not install the product on a carpet or
cushion.
tMake sure the air vent is not blocked by a
tablecloth or curtain.
Otherwise, this may result in re.
Take care not to touch the ventilation openings
when watching the monitor for long periods as
the ventilation openings may become hot. This
does not aect the operation or performance of
the product.
Periodically examine the cord of your appliance,
and if its appearance indicates damage or
deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with
an exact replacement part by an authorized
servicer.
Prevent dust collecting on the power plug pins
or outlet. This may cause a re hazard.
ENGLISH
7
Protect the power cord from physical or
mechanical abuse, such as being twisted,
kinked, pinched, closed in a door, or walked
upon. Pay particular attention to plugs, wall
outlets, and the point where the cord exits the
appliance.
Do not press strongly upon the panel with a
hand or sharp object such as nail, pencil or pen,
or make a scratch on it, as it may causedamage
to screen.
Avoid touching the screen or holding your
nger(s) against it for long periods of time.
Doing so may produce some temporary or
permanent distortion/damage to screen.
When cleaning the product and its components,
unplug the power rst and wipe it with a soft
cloth. Applying excessive force may cause
scratches or discolouration. Do not spray with
water or wipe with a wet cloth. Never use glass
cleaner, car or industrial shiner, abrasives or
wax, benzene, alcohol etc., which can damage
the product and its panel. Otherwise, this may
result in re, electric shock or product damage
(Deformation, corrosion or breakage).
As long as this unit is connected to the AC wall
outlet, it is not disconnected from the AC power
source even if you turn o this unit by SWITCH.
When unplugging the cable, grab the plug and
unplug it, by pulling at the plug.
Don’t pull at the cord to unplug the power
cord from the power board, as this could be
hazardous.
When moving the product, make sure you turn
the power o rst. Then, unplug the power
cables and all connecting cables.
The monitor set or power cord may be
damaged, which may create a re hazard or
cause electric shock.
When moving or unpacking the product,
work in pairs because the product is heavy.
Otherwise, this may result in injury.
Refer all servicing to qualied service
personnel. Servicing is required when the
apparatus has been damaged in any way, such
as power supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or
has been dropped.
8
ENGLISH
If the product feels cold to the touch, there may
be a small “icker” when it is turned on. This is
normal, there is nothing wrong with product.
This panel is an advanced product that contains
millions of pixels. You may see tiny black dots
and/or brightly coloured dots (red, blue or
green) at a size of 1ppm on the panel. This does
not indicate a malfunction and does not aect
the performance and reliability of the product.
This phenomenon also occurs in third-party
products and is not subject to exchange or
refund.
You may nd dierent brightness and color
of the panel depending on your viewing
position(left/right/top/down).
This phenomenon occurs due to the
characteristic of the panel. It is not related
with the product performance, and it is not
malfunction.
Displaying a still image for a prolonged period
of time may cause image sticking. Avoid
displaying a xed image on the monitor screen
for a long period of time.
Generated Sound
“Cracking” noise: A cracking noise that occurs
when watching or turning o the monitor
is generated by plastic thermal contraction
due to temperature and humidity. This noise
is common for products where thermal
deformation is required. Electrical circuit
humming/panel buzzing: A low level noise is
generated from a high-speed switching circuit,
which supplies a large amount of current to
operate a product. It varies depending on the
product.
This generated sound does not aect the
performance and reliability of the product.
Do not use high voltage electrical goods near
the monitor (e.g. electric mosquito-swatter).
This may result in product malfunction.
ENGLISH
9
Preparing
NOTE
tIf the monitor is turned on for the rst
time after it was shipped from the factory,
initialization of the monitor may take a few
minutes.
tImage shown may dier from your monitor.
tYour monitor’s OSD (On Screen Display)
may dier slightly from that shown in this
manual.
tThe available menus and options may dier
from the input source or product model that
you are using.
tNew features may be added to this monitor
in the future.
tThe items supplied with your product may
vary depending on the model.
tProduct specications or contents of this
manual may be changed without prior
notice due to upgrade of product functions.
tFor an optimal connection, HDMI cables
and USB devices should have bezels less
than 10 mm thick and 18 mm width. Use an
extension cable that supports USB 2.0 if the
USB cable or USB memory stick does not t
into your monitor’s USB port.
A
B
A
B
*A
<
10 mm
*B
<
18 mm
tUse a certied cable with the HDMI logo
attached.
tIf you do not use a certied HDMI cable, the
screen may not display or a connection error
may occur. (Recommended HDMI Cable
Types)
- High-Speed HDMI®/
TM
cable (3 m or less)
- High-Speed HDMI®/TM cable with Ethernet
(3 m or less)
tHow to use the ferrite core (Depending on
model)
- Use the ferrite core to reduce the
electromagnetic interference in the power
cord. Wind the power cord on the ferrite
core once.
[Wall side]
[Monitor side]
10 cm (+ / -2 cm)
10
ENGLISH
CAUTION
tDo not use any unapproved items to ensure
the safety and product life span.
tAny damage or injuries caused by using
unapproved items are not covered by the
warranty.
tSome models have a thin lm attached on
to the screen and this must not be removed.
tWhen attaching the stand to the monitor
set, place the screen facing down on a
cushioned table or at surface to protect
the screen from scratches.
tMake sure that the screws are inserted
correctly and fastened securely. (If they are
not fastened securely enough, the monitor
may tilt forward after being installed.) Do
not use too much force and over tighten the
screws; otherwise screw may be damaged
and not tighten correctly.
tMake sure to wring any excess water or
cleaner from the cloth.
tDo not spray water or cleaner directly onto
the monitor screen.
tMake sure to spray just enough of water or
cleaner onto a dry cloth to wipe the screen.
tWhen cleaning the product, be careful not
to allow any liquid or foreign objects to
enter the gap between the upper, left or
right side of the panel and the guide panel.
(Depending on model)
Lifting and moving
the monitor
Please note the following advice to prevent the
monitor from being scratched or damaged and
for safe transportation regardless of its type and
size.
tIt is recommended to move the monitor
in the box or packing material that the
monitor originally came in.
tBefore moving or lifting the monitor,
disconnect the power cord and all cables.
tWhen holding the monitor, the screen
should face away from you to avoid
damage.
tHold the top and bottom of the monitor
frame rmly. Make sure not to hold the
transparent part, speaker, or speaker grill
area.
ENGLISH
11
tWhen transporting a large monitor, there
should be at least 2 people.
tWhen transporting the monitor by hand,
hold the monitor as shown in the following
illustration.
tWhen transporting the monitor, do not
expose the monitor to jolts or excessive
vibration.
tWhen transporting the monitor, keep the
monitor upright, never turn the monitor on
its side or tilt towards the left or right.
tDo not apply excessive pressure to cause
exing /bending of frame chassis as it may
damage screen.
tWhen handling the monitor, be careful not
to damage the protruding buttons.
CAUTION
tAvoid touching the screen at all times, as
this may result in damage to the screen.
tDo not move the monitor by holding the
cable holders, as the cable holders may
break, and injuries and damage to the
monitor may occur.
Using the button
(Depending on model)
You can simply operate the monitor functions,
pressing or moving the button.
NOTE
t43/49UH61** series does not have a
Joystick functions but has only a power On/
O button.
Joystick Button
Dome Button
or
Basic functions
Power On (Press)
Power O (Press and
hold)
1
Volume Control
1 All running apps will close, and any
recording in progress will stop.
12
ENGLISH
Adjusting the menu
When the monitor is turned on, press the
button one time. You can adjust the Menu items
pressing or moving the buttons.
Turns the power o.
Clears on-screen displays and returns
to monitor viewing.
Changes the input source.
Accesses the settings menu.
Mounting on a
table
1 Lift and tilt the monitor into its upright
position on a table.
tLeave a 10 cm (minimum) space from the
wall for proper ventilation.
10 cm
10 cm
10 cm
10 cm
10 cm
2 Connect the power cord to a wall outlet.
CAUTION
tDo not place the monitor near or on sources
of heat, as this may result in re or other
damage.
Securing the monitor to a
wall
(This feature is not available for all models.)
1 Insert and tighten the eye-bolts, or monitor
brackets and bolts on the back of the
monitor.
tIf there are bolts inserted at the eye-bolts
position, remove the bolts rst.
2 Mount the wall brackets with the bolts to
the wall.
Match the location of the wall bracket and
the eye-bolts on the rear of the monitor.
3 Connect the eye-bolts and wall brackets
tightly with a sturdy rope. Make sure to keep
the rope horizontal with the at surface.
CAUTION
tMake sure that children do not climb on or
hang on the monitor.
NOTE
tUse a platform or cabinet that is strong
and large enough to support the monitor
securely.
tBrackets, bolts and ropes are not provided.
You can obtain additional accessories from
your local dealer.
ENGLISH
13
Mounting on a wall
Attach an optional wall mount bracket at the
rear of the monitor carefully and install the wall
mount bracket on a solid wall perpendicular to
the oor. When you attach the monitor to other
building materials, please contact qualied
personnel. LG recommends that wall mounting
be performed by a qualied professional
installer. We recommend the use of LG’s wall
mount bracket. LG’s wall mount bracket is
easy to move with cables connected. When
you do not use LG’s wall mount bracket, please
use a wall mount bracket where the device is
adequately secured to the wall with enough
space to allow connectivity to external devices.
It is advised to connect all the cables before
installing xed wall mounts.
10 cm
10 cm
10 cm
10 cm
Make sure to use screws and wall mount
bracket that meet the VESA standard. Standard
dimensions for the wall mount kits are
described in the following table.
Separate purchase(Wall
mounting bracket)
Model 43UH61** 49UH61**
VESA (A x B)
(mm)
200 x 200 300 x 300
Standard
screw
M6 M6
Number of
screws
4 4
Wall mount
bracket
LSW240B
MSW240
LSW350B
MSW240
A
B
CAUTION
tRemove the stand before installing the
monitor on a wall mount by performing the
stand attachment in reverse.
14
ENGLISH
Connections
(notications)
Connect various external devices to the monitor
and switch input modes to select an external
device. For more information of external
device’s connection, refer to the manual
provided with each device.
Available external devices are: HD receivers,
DVD players, VCRs, audio systems, USB storage
devices, PC, gaming devices, and other external
devices.
NOTE
tThe external device connection may dier
from the model.
tConnect external devices to the monitor
regardless of the order of the monitor port.
tRefer to the external equipment’s manual
for operating instructions.
tIf you connect a gaming device to the
monitor, use the cable supplied with the
gaming device.
tIn PC mode, there may be noise associated
with the resolution, vertical pattern,
contrast or brightness. If noise is present,
change the PC output to another resolution,
change the refresh rate to another rate or
adjust the brightness and contrast on the
PICTURE menu until the picture is clear.
tIn PC mode, some resolution settings
may not work properly depending on the
graphics card.
tIf ULTRA HD content is played on your PC,
video or audio may become disrupted
intermittently depending on your PC’s
performance. (Depending on model)
USB connection
Some USB Hubs may not work. If a USB device
connected using a USB Hub is not detected,
connect it directly to the USB port on the
monitor.
Other connections
Connect your monitor to external devices. For
the best picture and audio quality, connect the
external device and the monitor with the HDMI
cable. Some separate cable is not provided.
t
! !
!
General HDMI
ULTRA HD Deep Colour
- On : Support 4K @ 50/60 Hz (4:4:4, 4:2:2,
4:2:0)
- Off : Support 4K @ 50/60 Hz 8 bit (4:2:0)
If the device connected to Input Port also
supports ULTRA HD Deep Colour, your picture
may be clearer. However, if the device doesn’t
support it, it may not work properly. In that
case, connect the device to a dierent HDMI
port or change the monitor’s HDMI ULTRA
HD Deep Colour setting to Off.
(This feature is available on certain models
which are supported ULTRA HD Deep Colour
only.)
NOTE
tSupported HDMI Audio format :
Dolby Digital (32 kHz, 44.1 kHz, 48 kHz),
DTS (44.1 kHz, 48 kHz),
PCM (32 kHz, 44.1 kHz, 48 kHz, 96 kHz, 192
kHz)
(Depending on model)
ENGLISH
15
Remote control
The descriptions in this manual are based on the
buttons on the remote control. Please read this
manual carefully and use the monitor correctly.
To replace batteries, open the battery cover,
replace batteries (1.5 V AAA) matching the
and ends to the label inside the
compartment, and close the battery cover. To
remove the batteries, perform the installation
actions in reverse.
Make sure to point the remote control toward
the remote control sensor on the monitor.
(Depending on model)
A
B
INFO
A
(POWER) Turns the monitor on or o.
(INPUT) Changes the input source.
/ / Switches to external
inputs connected via HDMI1/HDMI2/HDMI3.
Switches to external inputs connected via
AV.
Number buttons Enters numbers.
(RATIO) Resizes an image.
(User Guide) Sees user-guide.
B
Views the information of the current
programme and screen.
(SEARCH) Search for content such as
monitor programmes, movies and other
videos, or perform a web search by entering
text in the search bar.
(MUTE) Mutes all sounds.
Adjusts the volume level.
Scrolls through the saved programmes.
Moves to the previous or next
screen.
16
ENGLISH
C
D
C
Shows the previous history.
(HOME) Accesses the Home menu.
By zooming in on the selected
area, you can view it in full screen.
Returns to the previous level.
Clears on-screen displays and returns to
monitor viewing.
Navigation buttons (up/down/left/right)
Scrolls through menus or options.
Selects menus or options and conrms
your input.
Changes the image mode.
Changes the sound mode.
D
Sets the sleep timer.
(Q. Settings) Accesses the Quick
Settings.
Control buttons ( )
Controls media contents.
Coloured buttons These access special
functions in some menus.
( : Red, : Green, : Yellow,
: Blue)
Licenses
Supported licenses may dier by model. For
more information about licenses, visit www.
lg.com.
Open source
software notice
information
To obtain the source code under GPL, LGPL,
MPL and other open source licenses, that is
contained in this product, please visit http://
opensource.lge.com.
In addition to the source code, all referred
license terms, warranty disclaimers and
copyright notices are available for download.
LG Electronics will also provide open source
code to you on CD-ROM for a charge covering
the cost of performing such distribution (such
as the cost of media, shipping, and handling)
upon email request to opensource@lge.com.
This oer is valid for three (3) years from the
date on which you purchased the product.
External control
device setup
To obtain the external control device setup
information, please visit www.lg.com.
Loading...