Lexicon 300 V3.0 User Manual

MIDI 48 kHz

44.1 kHz 32 kHz

300

DIGITAL EFFECTS SYSTEM

V3.0 Setups

300 V 3.0 Quick Reference Guide

7 89

PAGE

DOWN

LEVEL

The 300 V3.0 factory default state is: Analog In; 48kHz sampling rate.

456 123

—0

ENTER

SETUP

SELECT

MACH

STORE

VALUE

CONTROL

SETUP

EDIT

EFFECT

EDIT MOD

EDIT

BYPASS

POWER

The 300 is organized into Setups and Effects. Setups are collections of many decisions, including DSP routing (single or split), Input levels, Source, Balances, LFO Rate and Shape, and one (or two) Effects. These decisions are grouped together, named, and stored so they can be called up with a single user action.

Single Setups

Single Setups unify both Machine A and Machine B into a single DSP engine.

All Single Setup Presets are factory loaded with an Effect of the same name. (The Effect number may

not

be the

same.)

Setup Selection

Press SETUP SELECT, then use the Soft knob to select a Setup Preset. When you have found a Preset you want to load, press

ENTER.

An asterisk (*) in a Preset name indicates that one or more parameters are patched to the Soft knob.

Press PAGE UP to display any Soft knob patches made to Setup Effect parameters; press VALUE to show the parameter values.

To simplify the choice among the many possible effect and system routings, the 300 is shipped with 100 Setup Presets.

Analog

L R

Digital

Analog

Level

Digital

Level

Analog

Balance

Digital

Balance

Single Setup Presets

P101 Large Hall P102 Medium Hall P103 Small Hall P104 *Church P105 *Rooms P106 RehursalRoom P107 *Chamber P108 LiveDrumRoom P109 *Studio A P110 *Studio B P111 *Brick Wall P112 *Deep End P113 Oil Tanker P114 *Synth Hall P115 Dance Hall P116 *Ambience P117 In A Room

P118 Stairwell P119 *Hangar P120 MarbleFoyer P121 EarlyReflect P122 Lecture Hall P123 *CarInterior P124 Score Stage P125 Gate It!! P126 *Rich Plate P127 Glossy Plate P128 Warm Plate P129 Perc Plate P130 Contem-Plate P131 *EKO Plate P132 Bright Plate P133 *Round Plate P134 StereoAdjust

The Setup Presets are organized as follows:

101-150 = Single Setups 201-225 = Dual Mono Setups 301-325 = Cascade Setups

Dry

Effect Edit A

Dry

P135 Phase Invert P136 2 Frame Dly P137 3 Frame Dly P138 4 Frame Dly P139 MS Decode P140 *MultiEchoes P141 LFO Panner P142 Telephone P143 *Stereo Shift P144 Octave Down P145 Vox Chorus P146 Pole Flange P147 Bulkie Roll P148 Heavy Roll P149 *Going, Going P150 Zorch!

Overall

Mix

Analog and

Digital Out

Editing an Effect

Press EFFECT EDIT . Press the buttons above or below a parameter label to select it.

Turn the Soft knob to increase or decrease the parameter value.

Storing your changes

Once you have made changes to an Effect, remember that you must not only store those changes in Effect Edit mode, but also must store the Setup in which the Effect is loaded.

Note:

If the 300 Copy Tools function is set to DISABLE, no STORE functions can be performed.This function is enabled in CNTRL mode. (Selection of CNTRL does not interrupt audio operation of the 300.)

Press PAGE DOWN to view additional parameter pages; press EFFECT EDIT to return to the main edit screen.

From Effect Edit mode, press STORE . Turn the Soft knob to find an available register, then press

STORE again.

Press VALUE to alternate between a display of parameter names and a display of their values.

From Setup Edit mode, press STORE . Turn the Soft knob to find an available register, then press

STORE again.

Split Setups

300 V 3.0 Quick Reference Guide

To select a split setup, press

SETUP SELECT, use the

Soft knob to select a Setup Preset numbered 201-325,

Dual Mono Setups (201-

225) load one effect into Machine A (left out) and one into Machine B (right out).

then press ENTER.

Dual Mono Setup Presets

Setup Preset Mach A Effect Mach B Effect

P201 Rev/Rev P202 Rev/Dly P203 Rev/Pch P204 Rev/Comp P205 Dly/Dly P206 *Dly/Pch P207 Dly/Comp P208 *Pch/Pch P209 Pch / Comp P210 Comp/Comp P211 Slow Spin P212 WideFlang P213 X-Traffic P214 *GearUp

Cascade Setups (301-325) also load two effects: one is loaded into Machine A, then the audio from Machine A is passed to Machine B.

701 Chamber 702 Key Chamber 703 Drum Chamber 607 LFO:FazeDlys 705 Guitar Room 802 Guit Shift 707 “U”Chamber 901 EZ Comp2:1 609 Chorus 612 Chorus+EKOz 601 *Dual Delays 804 Sky Down 602 Space Delays 902 DrumComp3:1 803 *Up Shift 806 Echo down 810 Vocal Shift 902 DrumComp3:1 901 EZ Comp 902 DrumComp3:1 607 LFO:FazeDlys 609 Chorus 605 OverTheTop1 606 OverTheTop2 612 Chorus+EKOz 610 *Sky Delays 803 *Up Shift 805 Env*EKOShift

Analog or Digital

Input Level

Balance

Input

Dry

Σ Σ

Dry

Analog or Digital

Level

Balance

Patch Points

Effect Edit A

Effect Edit B

Patch Points

Setup Preset Mach A Effect Mach B Effect

P215 TwoRooms P216 TwoHalls P217 *Verbs P218 *RevPan P219 Up&Down P220 MyGuitar P221 EnvSpooge P222 Flng&Dlys P223 *Dly Daze P224 Clusters P225 2 Flanges

Patch Points

Effect Edit A

Patch Points

Mix

715 Joe's Garage 709 Basement 720 Recital Hall 710 Big Hall 717 *Drum Rooms 711 *Great Room 707 “U”Chamber 708 *’L’Chamber 807 HalfStepsUp 808 HalfStepsDn 802 Guit Shift 614 Env:Peak 614 Env:Peak 608 Env:Phazer 616 Negative Flang 602 Space Delays 604 *3VoiceDlys 603 *PingoPongo 612 Chorus+EKOz 604 *3Voice Dlys 606 OverTheTop2 804 Sky Down

Feedback

Effect Edit B

Feedback

Mix

Overall

Mix

Out

Mix

Out

Cascade Setup Presets

Setup Preset Effects loaded into Mach A and Mach B Setup Preset Effects loaded into Mach A and Mach B

P301 Rev->*Dly P302 *Dly->*Rev P303 Rev->Pch P304 Pch->Rev P305 Rev->Comp P306 Comp->Rev P307 Dly->Pch P308 Pch->*Dly P309 *Dly->Comp P310 Comp->*Dly P311 Pch->Comp P312 *SurrVerb P313 *V3Comp

701 Chamber 601 *Dual Delays 601 *Dual Delays 714 *Joe's B&G 707 “U”Chamber 802 Guit Shift 804 Sky Down 703 Drum Chamber 705 Guitar Room 901 EZ Comp 2:1 902 Drum Comp 3:1 709 Basement 609 Chorus 801 Mono Shift 810 Vocal Shift 603 *PingoPongo 604 *3Voice Dly 901 EZ Comp 2:1 901 EZ Comp 2:1 613 *Wall Slaps 802 Guit Shift 901 EZ Comp 2:1 720 Recital Hall 010 *Small St Adj 010 *Small St Adj 901 EZ Comp 2:1

P314 V3Chamber P315 *SpaceOut P316 *JetVerb P317 BigBricks P318 Rev->EKOz P319 Rev->Korus P320 Over!Top P321 GuitarXP P322 *EKO->Faze P323 Verb->Down P324 *The Sky P325 Spinola

701 Chamber 001 PONS+Dither 711 *Great Room 604 *3Voice Dlys 712 *Great Hall 616 NegativeFlng 713 Big Bricks 902 Drum Comp 3:1 710 Big Hall 612 Chorus+EKOz 706 Big & Short 609 Chorus 605 OverTheTop1 606 OverTheTop2 611 LFO:Pan&Faze 607 LFO:FazeDlys 805 Env*EKOShift 608 Env:Phazer 720 Recital Hall 806 Echo Down 804 Sky Down 610 *Sky Delays 609 Chorus 011 Panola

Editing Effects in Machine A and Machine B

Press EFFECT EDIT . Press the buttons above or below a parameter label to select it for Soft knob adjustment.

3 Oak Park • Bedford, MA 01730 USA • Tel 781-280-0300 • Fax 781-280-0499

Press VALUE to display parameter values. Press

MACH to toggle between

Machines A and B.

The 300 has many features which are not described here, such as the ability to trigger setup, effect and parameter changes based on a Time code Event List, Dynamic MIDI® functions, and more. For complete information on these, and other features, please read the 300 V3.0 Owner's Manual.

STORE your changes as described on the previous page. If you've changed parameters in both machines, you will have to perform a STORE operation for each effect. After the first effect is stored, press MACH and store the other, then store the Setup.

Lexicon Part No. 070-09683