Landoll 855 User Manual

Model 850/855 Series

Finisholl

Operator’ s Manual

LANDOLL CORPORATION

1900 North Street

Marysville, Kansas 66508

(785) 562-5381

800-428-5655 ~ WWW.LANDOLL.COM

F-133-0512 05/2012

1 Introduction

Understanding Safety Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

2 Standard Specifications 3 Assembly Instructions

Frame Assembly (11’ Through 27’ Models) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3

Frame Assembly (30’ Through 41’ Models) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3

Rockshaft Installation, Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5

Wings and Extensions Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

Rockshaft Installation, Wings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9

Hydraulic Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10

Shank Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-23

Table of Contents

SMV Bracket Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-24

Disc Gang Installation, 850 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-25

Coulter Assembly, 855 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-31

Pull Hitch Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-33

Leveling Assembly Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-35

Optional Hydraulic Radius Rod . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-37

Warning Lights Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-39

Rear Hitch Assembly (Option) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-41

Harrow Assembly Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-41

4 Operation and Maintenance

Tractor Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

Finisholl Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

Attaching to the Tractor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3

Field Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3

Wheel Bearing Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8

Hydraulic Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8

Transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8

Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8

F-133-0512 Edition i

Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10

5 Troubleshooting Guide

ii F-133-0512 Edition

Chapter 1

Introduction

The Landoll Model 850/855 Finisholl is a quality product designed to give years of trouble free performance. By following each section of this manual, your system will perform as designed for you and your operation

CHAPTER 1 gives basic instructions on the use of this manual. CHAPTER 2 gives product specifications. These specifications supply lengths and measures for your

equipment. A S tandard Bolt Torque Table is provided to give guidelines for bolt to rques to be used when servicing this product.

CHAPTER 3 contains assembly instructions for your Model 850/855 Finish oll. When these procedures

are correctly followed, your equipment should provide you years of trouble-free operation and service.

CHAPTER 4 instructs how to operate your equipment before using it, and describes adjustments

needed. It also gives practical advice for the care and maintenance of your Landoll equipment. Drawings in this section locate adjustment points on the equipment.

NOTE: IF THE EQUIPMENT IS IMPROPERLY ASSEMBLED OR MAINTAINED, THE WARRANTY IS VOID. IF YOU HAVE ANY QUESTIONS CONTACT:

LANDOLL CORPORATION

1900 NORTH STREET

MARYSVILLE, KANSAS 66508

or phone:

(785) 562-5381 or

(800) 428-5655 (888) 527-3909

CHAPTER 5 is a troubleshooting guide to aid in diagnosing and solving problems with the equipment. PARTS LIST is a separate manual showing the various assemblies, subassemblies, and systems.

Refer to that manual when ordering Landoll replacement parts. Order parts from your Landoll dealer.

WARRANTY The Warranty Registration form is included with the product documents. Fill it out and

mail it within 15 days of purchase.

NOTE: IMPROPER ASSEMBLY, MODIFICATION, OR MAINTENANCE OF YOUR LANDOLL MACHINE CAN VOID YOUR WARRANTY.

COMMENTS Address comments or questions regarding this publication to:

LANDOLL CORPORATION

1900 NORTH STREET

MARYSVILLE, KANSAS 66508

ATTENTION: PUBLICATIONS -DEPT. 55

1-1

INTRODUCTION



DANGER



WARNING



CAUTION

NOTE

Understanding Safety Statements

You will find various types of safety information on the following pages and on the machine signs (decals) attached to the vehicle. This section explains their meaning.

The Safety Alert Symbol means ATTENTION! YOUR SAFETY IS INVOLVED!

Danger means a life-threatenin g sit ua ti on ex is ts. Death can occur if safety measures or instructions on this label are not properly followed.

Warning means serious injury or death can occur if safety measures or instructions on this label are not properly followed.

Caution means serious equipment or other property damage can occur if instruction s on this label are not properly followed.

Means that failure to follow these instructions could cause damage to the equipment or cause it to operate improperly.

Make sure you read and understand the informatio n contained in this manual and on the machine signs (decals) before you attempt to operate or maintain this vehicle.

The safety statements contai ned in this manual relate to the operation of the Model 850/855 Finisholl.

1-2 F-133-0512 Edition

Standard Specifications

850 SERIES FINISHOLL W/ DISC BLADES

Chapter 2

MODEL

NO.

850-11 11’-4” 17 21 13’-0” N/A 4,580 850-14 14’-0” 21 22 15’-5” N/A 5,034 850-17 16’-8” 25 28 12’-0” 9’-0” 7,241 850-19 19’-4” 29 32 12’-0” 10’-3” 8,217 850-22 22’-0” 33 36 12’-0” 11’-6” 8,932 850-25 24’-8” 37 40 12’-0” 12’-9” 9,421 850-27 27’-4” 41 44 12’-0” 13’-11” 9,831 850-30 30’-0” 45 48 14’-8” 13’-11” 13,250

850-33N 32’-8” 49 52 14’-8” 16’-4” 14,500

850-33W 32’-8” 49 52 17’-4” 13’-11” 14,500

850-35 35’-4” 53 56 17’-4” 16’-4” 15,500 850-41 40’-8” 61 64 18’-4” 13’-7” N/A

MODEL

NO.

855-11 11’-4” 17 21 13’-0” N/A 4,580 855-14 14’-0” 21 22 15’-5” N/A 5,034 855-17 16’-8” 25 28 12’-0” 9’-0” 7,241 855-19 19’-4” 29 32 12’-0” 10’-3” 8,217 855-22 22’-0” 33 36 12’-0” 11’-6” 8,932 855-25 24’-8” 37 40 12’-0” 12’-9” 9,421 855-27 27’-4” 41 44 12’-0” 13’-11” 9,831 855-30 30’-0” 45 48 14’-8” 13’-11” 13,250

855-33N 32’-8” 49 52 14’-8” 16’-4” 14,500

855-33W 32’-8” 49 52 17’-4” 13’-11” 14,500

855-35 35’-4” 53 56 17’-4” 16’-4” 15,500

WORKING

WIDTH

WORKING

WIDTH

NO. OF

SHANKS

855 SERIES FINISHOLL W/ COULTER BLADES

NO. OF

SHANKS

NO. OF

BLADES

NO. OF

BLADES

TRANSPORT

WIDTH

TRANSPORT

WIDTH

TRANSPORT

HEIGHT

TRANSPORT

HEIGHT

ESTIMATED

WEIGHT (LBS.)

ESTIMATED

WEIGHT (LBS.)

2-1

STANDARD SPECIFICATIONS

LANDOLL CORPORATION

GENERAL TORQUE SPECIFICATIONS (REV. 4/97)

THIS CHART PROVIDES TIGHTENING TORQUES FOR GENERAL PURPOSE APPLICATIONS WHEN SPECIAL TORQUES ARE NOT SPECIFIED ON PROCESS OR DRAWING. ASSEMBLY TORQUES APPLY TO PLATED NUTS AND CAPSCREWS ASSEMBLED WITHOUT SUPPLEMENTAL LUBRICATIO N (AS RECEIVED CONDITION). THEY DO NOT APPLY IF SPECIAL GRAPHITE MOLY-DISULFIDE OR OTHER EXTREME PRESSURE LUBRICANTS ARE USED. WHEN FASTENERS ARE DRY (SOLVENT CLEANED), ADD 33% TO AS RECEIVED CONDITION TORQUE. BOLT HEAD IDENTIFICATION MARKS INDICATE GRADE AND MAY VARY FROM MANUFACTURER TO MANUFACTURER. THICK NUTS MUST BE USED ON GRADE 8 CAPSCREWS. USE VALUE IN [ ] IF USING PREVAILING TORQUE NUTS.

TORQUE IS SPECIFIED IN FOOT POUNDS

UNC

Size

SAE Grade2SAE Grade5SAE Grade

UNF Size

SAE Grade 2SAE Grade5SAE Grade

1/4-20 4 [5] 6 [7] 9 [11] 1/4-28 5 [6] 7 [9] 10 [12] 5/16-18 8 [10] 13 [16] 18 [22] 5/16-24 9 [11] 14 [17] 20 [25] 3/8-16 15 [19] 23 [29] 35 [43] 3/8-24 17 [21] 25 [31] 35 [44] 7/16-14 24 [30] 35 [43] 55 [62] 7/16-20 27 [34] 40 [50] 60 [75] 1/2-13 35 [43] 55 [62] 80 [100] 1/2-20 40 [50] 65 [81] 90 [112] 9/16-12 55 [62] 80 [100] 110 [137] 9/16-18 60 [75] 90 [112] 130 [162] 5/8-11 75 [94] 110 [137] 170 [212] 5/8-18 85 [106] 130 [162] 180 [225] 3/4-10 130 [162] 200 [250] 280 [350] 3/4-16 150 [188] 220 [275] 320 [400] 7/8-9 125 [156] 320 [400] 460 [575] 7/8-14 140 [175] 360 [450] 500 [625] 1-8 190 [237] 408 [506] 680 [850] 1-14 210 [263] 540 [675] 760 [950] 1-1/8-7 270 [337] 600 [750] 960 [1200] 1-1/8-12 300 [375] 660 [825] 1080 [1350] 1-1/4-7 380 [475] 840 [1050] 1426 [1782] 1-1/4-12 420 [525] 920 [1150] 1500 [1875] 1-3/8-6 490 [612] 110 [1375] 1780 [2225] 1-3/8-12 560 [700] 1260 [1575] 2010 [2512] 1-1/2-6 650 [812] 1460 [1825] 2360 [2950] 1-1/2-12 730 [912] 1640 [2050] 2660 [3325] 1-3/4-5 736 [920] 1651 [2063] 2678 [3347] 1-3/4-12 920 [1150] 2063 [2579] 3347 [4183]

METRIC

COARSE THREAD METRIC CLASS 10.9 FASTENERS AND CLASS 10.0 NUTS AND THROUGH HARDENED FLAT WASHERS, PHOSPHATE COATED, ROCKWELL “C” 38-45. USE VALUE IN [ ] IF USING PREVAILING TORQUE NUTS.

Nominal

Thread

Diameter

Standard Torque Nominal

Newton-

Meters

Foot-

Pounds

Thread

Diameter

Standard Torque

Newton-

Meters

Foot-

Pounds

6 10 [14] 7 [10] 20 385 [450] 290 [335] 7 16 [22] 12 [16] 24 670 [775] 500 [625] 8 23 [32] 17 [24] 27 980 [1105] 730 [825] 10 46 [60] 34 [47] 30 1330 [1470] 990 [1090] 12 80 [101] 60 [75] 33 1790 [1950] 1340 [1450] 14 125 [155] 90 [115] 36 2325 [2515] 1730 [1870] 16 200 [240] 150 [180] 39 3010 [3210] 2240 [2380] 18 275 [330] 205 [245]

Table 2-1: General Torque Specifications

2-2 F-133-0512 Edition

STANDARD SPECIFICATIONS

LANDOLL CORPORATION

HYDRAULIC FITTING TORQUE SPECIFICATIONS

THIS CHART PROVIDES TIGHTENING TORQUES FOR HYDRAULIC FITTING APPLICATIONS WHEN SPECIAL TORQUES ARE NOT SPECIFIED ON PROCESS OR DRAWING. ASSEMBLY TORQUES APPLY TO PLATED CARBON STEEL AND STAINLESS STEEL FITTINGS ASSEMBLED WITHOUT SUPPLEMENTAL LUBRICATION (AS

RECEIVED CONDITION). THEY DO NOT APPLY IF SPECIAL GRAPHITE MOLY-DISULFIDE OR OTHER EXTREME PRESSURE LUBRICANTS ARE USED. BRASS FITTINGS AND ADAPTERS - 65% OF THE TORQUE VALUE FOR STEEL. STAINLESS STEEL, ALUMINUM AND MONEL - THREADS ARE TO BE

LUBRICATED

TORQUE IS SPECIFIED IN FOOT POUNDS

Dash Size 37 Degree JIC O-Ring (ORS) O-Ring Boss (ORB)

-4 11-13 15-17 13-15

-5 14-16 — 21-23

-6 20-22 34-36 25-29

-8 43-47 58-62 40-44

-10 55-65 100-110 57.5-62.5

-12 80-90 134-146 75-85

-16 115-125 202-218 109-121

-20 160-180 248-272 213-237

-24 185-215 303-327 238-262

-32 250-290 — 310-340

JIC, ORS, & ORB (REV. 10/97)

PARKER BRAND FITTINGS

GATES BRAND FITTINGS

Dash Size 37 Degree JIC O-Ring (ORS) O-Ring Boss (ORB)

-4 10-11 10-12 14-16

-5 13-15 — —

-6 17-19 18-20 24-26

-8 34-38 32-40 37-44

-10 50-56 46-56 50-60

-12 70-78 65-80 75-83

-14 — 65-80 —

-16 94-104 92-105 111-125

-20 124-138 125-140 133-152

-24 156-173 150-180 156-184

-32 219-243 — —

AEROQUIP BRAND FITTINGS

Dash Size 37 Degree JIC O-Ring (ORS) O-Ring Boss (ORB)

-4 11-12 10-12 14-16

-5 15-16 — 18-20

-6 18-20 18-20 24-26

-8 38-42 32-35 50-60

-10 57-62 46-50 72-80

-12 79-87 65-70 125-135

-14 — — 160-180

-16 108-113 92-100 200-220

-20 127-133 125-140 210-280

-24 158-167 150-165 270-360

-32 245-258 — —

Table 2-2: Hydraulic Fitting Torque Specifications

2-3

STANDARD SPECIFICATIONS

2m410-011281

3-3/4

2-1/4

3-3/4

2-1/4

31911

Figure 2-1: 11’ Shank Placement Assembly

2-4 F-133-0512 Edition

STANDARD SPECIFICATIONS

2m410-011282

10-1/4

3-3/4

2-1/4

3-3/4

2-1/4

33191118-1/4

10-1/4

3-3/4

18-1/4

Figure 2-2: 14’ Shank Placement Assembly

2-5

STANDARD SPECIFICATIONS

2m410-011283

10-1/4

2-1/4

3-3/4

10-1/4

2-1/4

3-3/4

Figure 2-3: 16’-8”Shank Placement Assembly (1 of 2)

2-6 F-133-0512 Edition

STANDARD SPECIFICATIONS

2m410-011284

10-1/4

2-1/4

3-3/4

10-1/4

2-1/4

3-3/4

11319

Figure 2-4: 16’-8” Shank Placement Assembly (2 of 2)

2-7

STANDARD SPECIFICATIONS

2m410-011285

10-1/4

2-1/4

11-3/4

3-3/4

10-1/4

2-1/4

3-3/4

Figure 2-5: 19’-4” Shank Placement Assembly (1 of 2)

2-8 F-133-0512 Edition

STANDARD SPECIFICATIONS

2m410-011286

10-1/4

2-1/4

11-3/4

3-3/4

10-1/4

2-1/4

3-3/4

Figure 2-6: 19’-4” Shank Placement Assembly (2 of 2)

2-9

STANDARD SPECIFICATIONS

2m410-011287

10-1/4

2-1/4

3-3/4

10-1/4

2-1/4

3-3/4

2-1/4

10-1/4

11-3/4

Figure 2-7: 22’ Shank Placement Assembly (1 of 2)

2-10 F-133-0512 Edition

STANDARD SPECIFICATIONS

2m410-011288

10-1/4

2-1/4

3-3/4

10-1/4

2-1/4

3-3/4

2-1/4

10-1/4

11-3/4

Figure 2-8: 22’ Shank Placement Assembly (2 of 2)

2-11

STANDARD SPECIFICATIONS

2m410-011289

10-1/4

3-3/4

10-1/4

2-1/4

3-3/4

2-1/4

10-1/4

11-3/4

3-3/4

2-1/4

18-1/4

Figure 2-9: 24’-8” Shank Placement Assembly (1 of 2)

2-12 F-133-0512 Edition

STANDARD SPECIFICATIONS

2m410-011290

10-1/4

3-3/4

10-1/4

2-1/4

3-3/4

1132-1/4

10-1/4

11-3/4

3-3/4

2-1/4

18-1/4

Figure 2-10: 24’-8” Shank Placement Assembly (2 of 2)

2-13

STANDARD SPECIFICATIONS

2m410-011291

10-1/4

3-3/4

10-1/4

2-1/4

18-1/4

2-1/4

10-1/4

3-3/4

18-1/4

26-1/4

2-1/4

3-3/4

Figure 2-11: 27’-4” Shank Placement Assembly (1 of 2)

2-14 F-133-0512 Edition

STANDARD SPECIFICATIONS

2m410-011292

10-1/4

3-3/4

18-1/4

2-1/4

10-1/4

2-1/4

10-1/4

3-3/4

18-1/4

26-1/4

2-1/4

3-3/4

Figure 2-12: 27’-4” Shank Placement Assembly (2 of 2)

2-15

STANDARD SPECIFICATIONS

2m410-010293

10-1/4

3-3/4

10-1/4

2-1/4

19-3/4

18-1/4

11-3/4

2-1/4

10-1/4

3-3/4

18-1/4

26-1/4

2-1/4

3-3/4

2-1/4

2-3/4

Figure 2-13: 30’ Shank Placement Assembly (1 of 2)

2-16 F-133-0512 Edition

STANDARD SPECIFICATIONS

2m410-011294

10-1/4

3-3/4

10-1/4

2-1/4

19-3/4

18-1/4

11-3/4

2-1/4

10-1/4

3-3/4

18-1/4

2-1/4

3-3/4

2-1/4

2-3/4

26-1/4

Figure 2-14: 30’ Shank Placement Assembly (2 of 2)

2-17

STANDARD SPECIFICATIONS

2m410-011295

10-1/4

3-3/4

10-1/4

2-1/4

19-3/4

18-1/4

11-3/4

2-1/4

10-1/4

3-3/4

18-1/4

26-1/4

2-1/4

3-3/4

2-1/4

2-3/4

10-1/8

2-1/8

Figure 2-15: 33’NShank Placement Assembly (1 of 2)

2-18 F-133-0512 Edition

STANDARD SPECIFICATIONS

2m410-011296

10-1/4

3-3/4

10-1/4

2-1/4

19-3/4

18-1/4

11-3/4

2-1/4

10-1/4

3-3/4

18-1/4

26-1/4

2-1/4

3-3/4

2-1/4

2-3/4

2-1/8

Figure 2-16: 33’N Shank Placement Assembly (2 of 2)

2-19

STANDARD SPECIFICATIONS

2m410-011297

10-1/4

3-3/4

10-1/4

2-1/4

11-3/4

18-1/4

11-3/4

2-1/4

10-1/4

3-3/4

18-1/4

26-1/4

2-1/4

3-3/4

2-1/4

3-3/4

2-3/4

2-1/4

Figure 2-17: 33’ Shank Placement Assembly (1 of 2)

2-20 F-133-0512 Edition

STANDARD SPECIFICATIONS

2m410-011298

10-1/4

3-3/4

10-1/4

2-1/4

18-1/4

11-3/4

2-1/4

10-1/4

3-3/4

18-1/4

26-1/4

2-1/4

3-3/4

2-1/4

3-3/4

2-3/4

2-1/4

19-3/4

Figure 2-18: 33’ Shank Placement Assembly (2 of 2)

2-21

STANDARD SPECIFICATIONS

2m410-011299

10-1/4

3-3/4

10-1/4

2-1/4

11-3/4

18-1/4

11-3/4

2-1/4

10-1/4

3-3/4

18-1/4

26-1/4

2-1/4

3-3/4

2-1/4

3-3/4

2-3/4

2-1/4

10-1/8

2-1/8

Figure 2-19: 35’ Shank Placement Assembly (1 of 2)

2-22 F-133-0512 Edition

+ 64 hidden pages