Landoll 5K977 User Manual

5” Strap
Screw ½”-13 X 6”
7/16”-14 Lock Nut
Cultivator Bolt
Channel Adapter
S-Tine Bracket
ASSEMBLY OF THE 5K977 TIRE TRACK REMOVER KIT
Screw ½”-13 X 8”
Clamp
Screw 7/16”-14 X 3 ½”
Screw ½”-13 X 1½”
½”-13 Hex Nut
½” Lockwasher
8” Strap
3/8”-16 Flange Nut
Centered behind each tractor tire, attach a set of Channel Adapters to the Pulverizer frame using the 8” Straps and ½” X 8” Bolts, Lockwashers, and Hex Nuts. Ensure that the Channel Adapter end with four holes is downward. Prior to inserting the bottom 8” Bolts line up the S-Tine bracket with the four lower holes on the Channel Adapter. Attach with 8” Bolts and Hex Nuts in the top holes. The 1 ½ Screws, Lockwashers and Nuts are inserted in the two bottom holes. Tighten all fasteners at this time.
Attach Tooth bar Tubes to the S-Tine Brackets using 5” Straps and ½” X 6” Bolts, Lockwashers, and Nuts. Tighten all fasteners at this time.
Locate and install S-Tines as needed to cover tractor tire tracks. The recommended positions of the S-Tines is to set the middle tine in line with the center of the tractor tire and the outer tines just beyond the outer edge of the tractor tire.
Attach the Duckfoot and Reversible Points to the S-Tines using the Cultivator Bolts and 3/8” Flange Nuts. The suggested pattern is to use the Reversible Point on center tine and Duckfoot Points on each side. If needed, additional tines may be purchased and installed.
Reversible Point
Tooth Bar Tube
Check for interference between tractor tires and S-Tines. If this occurs, the Tooth Bar Tubes can be mounted behind rearmost vertical member on the S-Tine brackets.
1212 5K978
11
16
10
7
6
13
14
4
2
5
15
1
3
12
17
9
8
18
5K977 Wheel Track Remover Kit
ITEM PART NUMBER DESCRIPTION QTY
1 1J887 S-TINE, 10mm X 32mm 6 2 7D014 DUCKFOOT POINT 4 3 2J155 HEAVY DUTY REVERSIBLE POINT 2 4 7D728 CULTIVATOR BOLT 6 5 5J616 FLANGE LOCK NUT 3/8-16 6 6 1-654-010055-17 SCREW,HEX CAP,1/2-13UNCX6 GR5 8 7 5J358 STRAP (5”) 8 8 1-861-010034-13 WASHER, LKG HLCL SPR, 1/2 32 9 1-512-010007-09 NUT, HEX 1/2-13 ZP 32 10 3K320 STRAP (8”) 8 11 174888 CHANNEL, ADAPTER 4 12 9J474 BRACKET 4 13 1J834 CLAMP 6 14 101988 NUT,HEXSLF-LKG 7/16-14 GRB 6 15 2J241 SCREW 7/16-14NCX3-1/2RDHD SQNK 6 16 2P158 HHCS, 1/2-13 X 8, GR5, ZP 16 17 1-654-010055-03 SCREW,HEX CAP, 1/2-13UNCX1-1/2 8 18 5K975 TOOTH BAR TUBE 2 19 5K978 INST PPD TRACK REMOVER KIT 1
1212 5K978