Landoll 175116 User Manual
INSTALLATION INSTRUCTIONS FOR
CAUTION
NOTICE
NOTE
Trunnion Bearing Retrofit Kit P/N 175116
WFP22-36 built prior to September 2012 with 4” X 4” front frame tube
Do not work on or under this machine unless
securely
tractor or by other sufficient means!
• Identify the parts listed below.
• Place the Wing Float Pulverizer in a suitable area
to work with the frame while the wings are
unfolded.
• Make sure all hydraulic pressure is neutralized.
blocked and supported by a hoist or
Understand the procedure before doing the work.
Use proper tools and equipment.
The Retrofit procedure is the same for both kits, the only
difference being the Right/Left Hand Hangers, Items 15
and 16, in the parts table. This is due to the Front Frame
Tube dimension.
Kit 175116 - Parts List
For machines built prior to September 2012 with 4” X 4” front frame tube
ITEM PART NUMBER DESCRIPTION QTY
175116 KIT, TRUN BRG HNG RETRO 4X4
1 1-654-010061-06 SCREW,HXCP, 3/4-10UNCX2-1/4GR5 12
2 1-861-010034-17 WASHER, LKG, HLCL SPR, 3/4 12
3 1-861-010034-21 WASHER, LKG HEL SPRG 1IN 6
4 1J136 SPRAY CAN RED PAINT 1
5 137943 SCREW,HEX CAP 1-8UNCX2-1/4GR5 6
6 140477 BEARING, DISC 1.775 ID ASSY 6
7 140479 MOUNT, TRUNNION BEARING 12
8 154185 WASHER, 3/8 THICK 1” ID 6
9 154186 WASHER, FLAT TOP 6
10 171738 WASHER, SHIM 11 GA, 1.79 ID 12
11 171739 WASHER, SHIM 14 GA, 1.79 ID 6
12 173119 SHAFT-STUB, AXLE, WELDMENT 6
13 174879 BOLT ON BEARING HANGER 2
14 174880 PLATE-BEARING MOUNT 2
15 175120 HANGER, RH SUB-WELD, 4 X 4 1
16 175121 HANGER, LH SUB-WELD, 4 X 4 1
17 528934 REFLECTOR - YELLOW 2
18 9D674 HOSE TIE - 8” 4
F-715 Brillion Farm Equipment 1-1
Landoll Corporation
INSTALLATION INSTRUCTIONS FOR
CAUTION
NOTICE
NOTE
Trunnion Bearing Retrofit Kit P/N 174940
WFP22-36 built between September 2012 and January 2013 with 4” X 6” front frame tube
Do not work on or under this machine unless
securely
tractor or by other sufficient means!
• Identify the parts listed below.
• Place the Wing Float Pulverizer in a suitable area
to work with the frame while the wings are
unfolded.
• Make sure all hydraulic pressure is neutralized.
blocked and supported by a hoist or
Understand the procedure before doing the work.
Use proper tools and equipment.
The Retrofit procedure is the same for both kits, the only
difference being the Right/Left Hand Hangers, Items 15
and 16, in the parts table. This is due to the Front Frame
Tube dimension.
Kit 174940 - Parts List
For machines built between September 2012 to January 2013 with 4” X 6”
front frame tube
ITEM PART NUMBER DESCRIPTION QTY
174940 KIT, TRUN BRG HNG RETRO
1 1-654-010061-06 SCREW,HXCP, 3/4-10UNCX2-1/4GR5 12
2 1-861-010034-17 WASHER, LKG, HLCL SPR, 3/4 12
3 1-861-010034-21 WASHER, LKG HEL SPRG 1IN 6
4 1J136 SPRAY CAN RED PAINT 1
5 137943 SCREW,HEX CAP 1-8UNCX2-1/4GR5 6
6 140477 BEARING, DISC 1.775 ID ASSY 6
7 140479 MOUNT, TRUNNION BEARING 12
8 154185 WASHER, 3/8 THICK 1” ID 6
9 154186 WASHER, FLAT TOP 6
10 171738 WASHER, SHIM 11 GA, 1.79 ID 12
11 171739 WASHER, SHIM 14 GA, 1.79 ID 6
12 173119 SHAFT-STUB, AXLE, WELDMENT 6
13 174879 BOLT ON BEARING HANGER 2
14 174880 PLATE-BEARING MOUNT 2
15 174937 HANGER, RH SUB-WELD (4” X 6”) 1
16 174942 HANGER, LH SUB-WELD (4” X 6”) 1
17 528934 REFLECTOR - YELLOW 2
18 9D674 HOSE TIE - 8” 4
1-2 Brillion Farm Equipment F-715
Landoll Corporation
Step 1
Remove the Left Hand and Right
Hand Center Frame Bearing
Hangers.
Left Hand
Right Hand
P/N 175121 for the 4” X 4” Tube
P/N 174942 for the 4” X 6” Tube
P/N 175120 for the 4” X 4” Tube
P/N 174937 for the 4” X 6” Tube
Weld the new Bearing Hangers in place.
Touch up any exposed metal with spray
paint provided.
• Remove the existing Center Frame Left and Right
Hand Bearing Hangers.
• Weld the new Left and Right Hand Bearing Hangers
in place. See Figures 1-2, 1-3, and 1-4 for placement
and welding information.
• See the Part Numbers below that corresponds to
your Front Frame Tube size.
Figure 1-1: Step 1
F-715 Brillion Farm Equipment 1-3
Landoll Corporation
157 7/16"
154 1/2"
13"
REF
6"
REF
9 3/4"
4"
TUBE HEIGHT
9 3/4"
4"
TUBE
WIDTH
23/32"
REF
6 1/8"
REF
1 13/16"
REF
1 21/32"
Figure 1-2: Center Frame Bearing Hanger Placement 4” X 4” Tube
1-4 Brillion Farm Equipment F-715
Landoll Corporation
154 1/2" REF
9 1/4"
9 1/4"
13"
REF
6"
REF
6"
TUBE
HEIGHT
157 7/16"
1 21/32"
5 5/8"
REF
1 13/16"
REF
4"
TUBE
WIDTH
23/32"
REF
Figure 1-3: Center Frame Bearing Hanger Placement 4” X 6” Tube
F-715 Brillion Farm Equipment 1-5
Landoll Corporation
Loading...