Landoll 164703 User Manual

PT PULVERIZER WARNING LIGHT

INSTALLATION INSTRUCTION SHEET

P/N 164703

LANDOLL CORPORATION

1900 North Street

Marysville, Kansas 66508

[phone]

800-428-5655 ~ WWW.LANDOLL.COM

164703

PT PULVERIZER WARNING LIGHT INSTALLATION

NOTICE

!

CAUTION

!

WARNING

!

DANGER

NOTE

!

DANGER

INSTRUCTION BOOKLET

Instructions for Ordering Parts

** Repair parts must be ordered through an authorized dealer **

DEALER INSTRUCTIONS FOR ORDERING PARTS FROM LANDOLL PARTS DISTRIBUTION CENTER

PHONE #: [phone] OR 785-562-5381 FAX #: [phone]
ORDER ONLINE: comnet.landoll.com

Understanding Safety Statements

• Examine safety decals and be sure you have the
correct safety decals for your machine. Order
replacement decals through your Brillion dealer.

Special notice - read and thoroughly understand.

Proceed with caution. Failure to heed caution
may

cause injury to person or damage product.

Proceed with caution. Failure to heed warning will
cause injury to person or damage product.

You should read and understand the information
contained in this manual and on the machine decals
before you attempt to operate or maintain this equipment.

• Keep Riders Off of Machinery

Do not allow anyone to ride on tractor or
machine. Riders could be struck by foreign
objects or thrown from the machine.

• Never allow children to operate equipment.

• Keep bystanders away from machine during
operation.

Proceed with extreme caution. Failure to heed
notice will cause injury or death to person and/or
damage product.

1-1

PT PULVERIZER WARNING LIGHT INSTALLATION INSTRUCTION BOOKLET

!

WARNING

NOTE

NOTE

PT 10 INSTALLATION

Lower machine to ground before removing any
hardware

Install light brackets:

1. Position the inner light brackets for red lamps to be
within 48" of the center of the machine. Secure with
the U-Bolt and locknut. See Figure 1-1.

2. Secure outer light brackets with outer bearing hanger
U-Bolts.

Install warning lamps:

1. Install the outer warning lamps (amber) and lamp
shield to outer brackets with ¼-20 x 1-1/2 hex head
cap screws and ¼-20 flanged lock nuts.

2. Install the inner warning lamps (red) to inner brackets
with ¼-20 x 1-1/4 hex head cap screws and ¼-20
flanged lock nuts. Make sure the red lens is rear
facing.

9. Tighten all hardware.

Install reflectors:

1. Install the (4) reflector brackets to center frame end
plates using ½-13 x 1-1/2 hex head cap screws, flat
washers, and lock nuts (8 each).

2. Adjust the bracket angles to be as vertical as
possible with machine raised and the drawbar height
at transport height.

3. Tighten hardware.

4. Apply the reflector decals to brackets. The amber
reflectors should be on the front brackets; the red
and orange fluorescent reflectors should be rear
facing.

5. Apply the remaining 2 amber reflectors to the outside
of each wheel arm. See Figure 1-1.

6. Install SMV emblem to the bracket by fastening it with
2 - 5/16”-18 x 1” screws, flat washers and NY-LOK
nuts.

7. Attach the bracket to the left side of the center
bearing hanger.

Install electrical wiring and module:

1. Lay out the wishbone harness, making sure the sides
marked left or right are correct.

2. Starting at the center of the machine, thread the
harness ends through openings in the center frame
lift weldment and light brackets, ending at the outer
light bracket.

3. Install the enhanced lighting module by fastening it
with #8 screws, flat washers, lock washers and nuts
(2 each) to the inside of the center frame lift
weldment plate.

4. Lay out the tractor harness on the drawbar, making
connection at the lighting module.

5. Secure the tractor harness to the hydraulic hose with
cable ties, making sure to leave enough slack at the
lift weldment to allow the machine to raise and lower.

6. Connect the wishbone harness to module, bundle
any excess wire and secure with cable ties.

Be sure inner light brackets do not interfere with the
frame braces as the machine cycles.

7. Raise the machine if not done previously.

8. Adjust the lamp angles so lamps are vertical with the
drawbar height adjusted to the transport height.
Adjustment is provided to compensate for high
drawbar heights if used as a companion tool or lower
heights if towed directly behind a tractor.

Final assembly should have red lamps within 48" of the
center of the machine and amber lamps within 16" of
machine extremity.

1-2