La Crosse Technology WS-9007U-IT, WS-9007U-IT User Manual
Contents
y
Language Page
___________________________________________________________________
English 1
French
Spanish
1
TABLE OF CONTENTS
Topic
Inventory of Contents
Features
Setting Up
Battery Installation
Function keys
LCD Screen and Settings
Manual Settings
Weather Forecast and Tendency
Indoor Temperature Display and Indoor MIN/MAX Records
Outdoor Temperature Display and Outdoor MIN/MAX Records
915 MHz Reception
Mounting
Troubleshooting
Maintenance and care
Specification
Warranty Information
2
Page
This product offers:
INVENTORY OF CONTENTS
1. Wireless Temperature Station
2. Wireless Temperature Sensor (TX38U) and mounting bracket.
3. Instruction Manual and Warranty Card.
ADDITIONAL EQUIPMENT (not included)
1. 1 Philips screwdriver.
2. 2 Fresh “AAA” IEC LR3, 1.5V Alkaline Batteries
3. 2 Fresh “AA” IEC LR6, 1.5V Alkaline Batteries.
INSTANT TRANSMISSION is the state-of-the-art new
wireless transmission technology, exclusively
designed and developed by LA CROSSE
TECHNOLOGY. INSTANT TRANSMISSION offers you
an immediate update (every 27.5 seconds!) of all your
outdoor data measured from the transmitters: follow
your climatic variations in real-time!
3
FEATURES:
The Temperature Station
LCD
Displa
Function
Keys
Temperature display in degrees Fahrenheit (°F)
Indoor and Outdoor temper ature display with MIN/MAX recording
All MIN/MAX recordings can be reset
Low battery indicator
Wireless transmission at 915 MHz
4
Hanging hole
Battery
compartment
cover
Foldout
Stand
Outdoor signal reception intervals at 27.5-second
Table standing or wall mounting
The Outdoor Temperature Transmitter
SETTING UP:
NOTE: The temperature station will receive only outdoor transmitter only.
Remote transmission of outdo o r tem pera tu re t o
Temperature Station by 915 MHz
Shower proof casing
Wall mounting case
Mounting at a sheltered place. Avoid direct rain
and sunshine
1. First, insert the batteries into the Temperature transmitter. (see “Install and replace
batteries in the Temperature transmitter“).
2. Immediately after and within 2 minutes, insert the batteries into Tempe rature station
(see “Install and replace batteries in the Temperature station”). Once the
batteries are in place, all segments of the LCD will light up briefly. Then the indoor
temperature will de display. If these are not displayed after 60 seconds, remove the
batteries and wait for at least 10 seconds before reinserting them.
3. After inserting the batteries into the transmitter, the Temperature station will start
receiving data from the transmitter. The outdoor t emperature and the signal reception
icon should then be displayed on the Temperature station. If this does not happen
after 3 minutes, the batteries will need to be removed from both units and reset from
step 1.
4. In order to ensure sufficient 915 MHz transmission however, this should under good
conditions be a distance no more than 330 feet (TBC) (100 meters-TBC) between the
final position of the Temperat ure Station and the transmitter (see notes on
“Mounting” and “915 MHz Re c e ption”).
Note:
If the signal reception is not successful on the first fr equency (915MHz) for 22 seconds,
the frequency is changed to 920MHz and the learning is tried another 22 seconds. If still
not successful the reception is tried for 22 seconds on 910MHz. This will also be done
for re-synchronization.
INSTALL AND REPLACE BATTERIES IN THE TEMPERATURE TRANSMITTER
start-up and this code must be received and stored by the Weather station in the first 3
minutes of power being supplied to it
The Temperature Transmitter uses 2 x AAA, IEC LR3, 1.5V
battery. To install and replace the batteries, please follow the
steps below:
1. Pull out the battery holder at the bottom of the transmitter.
2. Insert the batteries, ob serving the correct polarity (see
marking).
3. Replace the battery holder on the unit.
Note:
In the event of changing batteries in any of the units, all units
need to be reset by following the setting up procedures. This is
because a random security code is assigned by the transmitter at
5
INSTALL AND REPLACE BATTERIES IN THE TEMPERATURE STATION
BATTERY CHANGE:
It is recommended to replace the batteries in all units on an annual basis to
ensure optimum accuracy of these units.
Please participate in the preservation of the environment. Return
used batteries to an authorised depot.
6
The Temperature station use s 2 x AA, IEC LR6,
1.5V batteries. To install and replace the
batteries, please follow the steps below:
1. Remove the cover at the back of the
weather station.
2. Insert batteries observing the correct
polarity (see marking).
3. Replace compartment cover.
7
8
Loading...