La Crosse Technology WS-7034U, WS-8256-AL User Manual

WS-7034U

Wireless 433 MHz

Temperature Station

Instruction Manual

TABLE OF CONTENTS

Topic Page

Quick Setup 3-5 Inventory of Contents 6-7 Detailed Setup Guide

Battery Installation 8 Setting the Time 9-10 Selecting Units of Measurement

Features

Minimum and Maximum Temperatures

Resetting Minimum and

Maximum Temperatures Adding additional remote temperature sensors (optional) Mounting 15-16 Troubleshooting 17-18 Maintenance and Care 19 Specifications 20-21 Warranty Information 22-25

13-14

QUICK SETUP

Hint: Use good quality Alkaline Batteries and avoid rechargeable batteries.

1. Have the indoor temperature station and remote temperature sensor 3 to 5 feet apart.

2. Batteries should be out of both units for 10 minutes.

3. Place the batteries into the remote temperature sensor first then into the indoor temperature station.

(All remote temperature sensors must be started before the indoor temperature station)

4. DO NOT PRESS ANY BUTTONS FOR 10 MINUTES.

In this time the indoor temperature station and remote temperature sensor will start to talk to each other and the display will show both the indoor temperature and an outdoor temperature. If the indoor temperature station does not display both temperatures after the 10 minutes please retry the set up as stated above. After both indoor and outdoor temperatures are displayed for 10 minutes you can place your remote temperature sensor outdoors and set your time.

The remote temperature sensor should be placed in a dry, shaded area. The remote temperature sensor has a range of 80 feet. Any walls that the signal will have to pass through will reduce distance. An outdoor wall or window will have 20 to 30 feet of resistance and an interior wall will have 10 to 20 feet of resistance. Your distance plus resistance should not exceed 80 ft. in a straight line. NOTE: Fog and mist will not harm your remote temperature sensor but direct rain must be avoided.

To complete the set up of your indoor temperature station after the 10 minutes have passed please follow the steps on pages 8-9.

INVENTORY OF CONTENTS

1. The indoor temperature station (Figure 1)

2. The remote temperature sensor (TX6U) and mounting bracket. (Figure 2)

3. 3 each, 1/2” Philips screws.

4. One strip of double sided adhesive tape.

Instruction Manual and Warranty Card.

Figure 1

(not included)

Holder

Figure 2

ADDITIONAL EQUIPMENT

1. 1 Philips screwdriver.

2. 2 Fresh AAA Alkaline batteries.

3. 2 Fresh AA Alkaline batteries

DETAILED SETUP GUIDE

Battery Installation

1. Install 2 AA batteries in the remote temperature sensor. Make sure they do not spring free, or start-up problems may occur.

Install 2 AAA batteries in the indoor temperature station. Do not press any buttons for at least ten minutes.

Setting the Time

Battery Cover

1. Press and hold the “SET” button for 5 second, “12h” will appear in the TIME LCD.

2. Press and release the “MIN/MAX” button to select either 12h time (am/pm) or 24h time

3. Press and release the “SET” button 2 times, the hour will flash in the upper left corner.

4. Press and release the “MIN/MAX” button to set the hours

5. Press and release the “SET” button to move to the minute setting

6. Press and release the “MIN/MAX” button to set the minutes.

7. Press and release the “SET” button to activate the clock.

Note: When in 12h mode, there is only a “PM” display, which appears under “TIME.” If there is no display here it is AM. Make sure you set the time accordingly.

Selecting Units of Measurement

1. Press and hold the “SET” button for 5 second until “12h” or “24h” appears in the TIME LCD.

2. Press and release the “SET” button again, “°F” will appear in the TIME LCD.

3. Press and release the “MIN/MAX” button to shift between °F and °C.

4. Press and release the “SET” button twice to activate settings.

+ 4 hidden pages