La Crosse Technology WS-7025TWC User Manual

WS-7025TWC

Wireless 433 MHz

Radio-controlled Weather Station

Instruction Manual



Topic Page

Inventory of Contents/Additional Equipment 3
About WWVB 4
Quick Set-Up Guide 5

Detailed Set-Up Guide

Battery Installation 6-7

Program Mode

Function Keys 7
12/24 Hour Time Setting 7
Time Zone Setting 7-8
Daylight Saving Time Setting 8-9
Time Setting (WWVB & Manual) 9-10
Setting Day, Date and Year 10-11
Selecting °F or °C
Setting the LCD Contrast 11
Features
Back Light 12
Weather Forecast 12-13
Indoor Temperature, Humidity & Comfort
Level Indicator
Outdoor Temperatures 14
Minimum & Maximum Records (Indoor,
Outdoor & Resetting)
Alarm (Setting, Snoozing & Stopping) 16
Additional Remote Temperature Sensor

Units (Set-Up, Viewing & Operation)
Mounting 18-20
Troubleshooting 21
Maintenance & Care 22
Specifications 23
Warranty Information 24-25

11

14

14-15

17-18

Table Of Contents

2

INVENTORY OF CONTENTS

1. The weather station (Figure 1).

2. One TX6U remote temperature sensor with mounting bracket
(Figure 2).

3. Three each, ½” Philips screws.

4. One strip double-sided adhesive tape.

5. Instruction Manual and Warranty Card.

Time LCD

Figure 1

ADDITIONAL EQUIPMENT (not included)

1. Two, fresh AA 1.5V batteries for indoor weather station.

2. Two, fresh AA 1.5V batteries for remoter temperature sensor.

3. One, Philips screwdriver for mounting.



Figure 2

Mounting
Bracket

3

ABOUT WWVB (Radio Controlled Time)

The NIST (National Institute of Standards and Technology—Time and Frequency

Division) WWVB radio station is located in Ft. Collins, Colorado and transmits the
exact time signal continuously throughout the United States at 60 kHz. The signal
can be received up to 2, 000 miles away through the internal antenna in the weather
station. However, due to the nature of the earth’s ionosphere, reception is very
limited during daylight hours. The weather station will search for a signal every
night when reception is best. The WWVB radio station derives its signal from the
NIST Atomic clock in Boulder, Colorado. A team of atomic physicists is
continually measuring every second, of every day, to an accuracy of ten billionths of
a second per day. These physicists have created an international standard measuring
a second as 9,192,631,770 vibrations of a Cesium-133 atom in a vacuum.

4

QUICK SET-UP GUIDE

Hint: Use good quality Alkaline Batteries and avoid rechargeable batteries.

1. Have the indoor weather station and remote temperature sensor 3 to 5
apart.

2. Batteries should be out of both units for 10 minutes.

3. Place the batteries into the remote temperature sensor first then into
the indoor weather station.
(All remote temperature sensors must be started before the indoor

weather station)

4. DO NOT PRESS ANY BUTTONS FOR 10 MINUTES.

In this time the indoor weather station and remote temperature sensor will start to
talk to each other and the indoor weather station will show both the indoor
temperature and an outdoor temperature. If the indoor weather station does not
display both temperatures after the 10 minutes please retry the set up as stated above.
After both indoor and outdoor temperatures are displayed for 10 minutes you can
place your remote temperature sensor outdoors and set your time.

The remote temperature sensor should be placed in a dry, shaded area. The remote
temperature sensor has a range of 80 feet. Any walls that the signal will have to pass
through will reduce distance. An outdoor wall or window will have 20 to 30 feet of
resistance and an interior wall will have 10 to 20 feet of resistance. Your distance
plus resistance should not exceed 80 ft. in a straight line.

NOTE: Fog and mist will not harm your remote temperature sensor but direct rain
must be avoided.

To complete the set up of your indoor weather station after the 10 minutes have
passed please follow the steps on pages 8 and 9.

The remote temperature sensor transmits a signal every 3 minutes;

Note:

after the batteries have been installed, the indoor weather station will
search for the signal for a duration of 5 minutes. If there is no temperature
reading in the OUTDOOR LCD after 5 minutes, make sure the units are
within range of each other or repeat the battery installation procedure.

5

DETAILED SET-UP GUIDE

I. BATTERY INSTALLATION

A. REMOTE TEMPERATURE SENSOR

1. Remove the mounting bracket. The
bracket snaps on and off easily.

2. Remove the battery cover, by sliding the
cover down.

3. Observing the correct polarity install 2
AA batteries. The batteries will fit
tightly (to avoid start-up problems make
sure they do not spring free).

4. Replace the battery cover by sliding
upwards. Be sure battery cover is on
securely.

B. INDOOR WEATHER STATION

1. Remove the battery cover. To
do this, insert a solid object in
the space provided at the
lower-central position of the
battery cover, then push up and
pull out on the battery cover.

2. Observe the correct polarity,
and install 2 AA batteries.

3. Replace the battery cover.

Immediately after the batteries have been installed, each

Note:

LCD (Liquid Crystal Display) will flash and a tone will sound.
Within a few seconds the indoor temperature, indoor relative
humidity and the weather icons (sun and clouds) will be displayed.
If not, then remove batteries for 10 seconds and reinstall. If the
outdoor temperature is not displayed within four minutes, remove
batteries from both units, wait 10 seconds, and reinstall. The time
will show -:-- and start searching for the signal. If it successfully

Battery
Cover

6

receives the time signal (usually at night), it will display the
correct time (default is Eastern).

PROGRAM MODE

Programming Note:

the OUT button is pressed during programming modes, the unit will set the
last information entered—the display will stop flashing and return to
normal time-date readings. If you don’t leave the program mode during the
programming of sections III through VIII, you can advance to step 3 of the
next program setting. If you do leave the program setting (or want to
program a specific setting) follow each instructional step to program that
setting.

I. FUNCTION KEYS

The function keys are operated by pressing the top

or bottom of the key corresponding to the
operation that you want to perform.

II. 12 OR 24 HOUR TIME SETTING

1. Press and hold the “SET” button for 3 seconds or until “12 h”
flashes in the DATE LCD.

2. Press and release the “CH” button to toggle between 12 and
24-hour time.

3. Press and release the “SET” button to confirm the 12/24-hour
setting and to advance to Time Zone Setting.

III. TIME ZONE SETTING

The default time zone is EST, “-5hr” (Eastern Standard Time), to
change this setting:

1. Press and hold the “SET” button for 3 seconds or until “12 h”
OR “24 h” flashes in the DATE LCD.

2. Press and release the “SET” button 1 more time to enter the
Time Zone setting mode. The default Time Zone “-5” will
flash in the DATE LCD.

If 30 seconds are allowed to pass or either the IN or

7

3. Select your appropriate time zone using the CH button.
During selection of the Time Zone, the 3 letter abbreviations
for the time zones found in North America will flash across
the top of the TIME LCD. Observe the chart below, showing
the corresponding abbreviations, time zones, and codes.

TIME ZONES

GMT 0

Atlantic -4
EST; Eastern -5
CST; Central -6

MST; Mountain -7

PST; Pacific -8

ALA; Alaska -9

HAW; Hawaii -10

There are more time zones represented by numbers than there are

Note:

represented by 3 letter abbreviations. If you live in North America you
need only be concerned with the ones in the chart above.

4. Press and release the “SET” button to confirm and advance to
the Daylight Saving Time setting.

IV. DAYLIGHT SAVING TIME (DST) SETTING

1. Press and hold the “SET” button for 3 seconds or until “12 h”
or “24 h” flashes in the DATE LCD.

2. Press and release the “SET” button 2 more times to reach the
DST selection mode. “DST 1” is the default setting and will
be flashing in the DATE LCD.

3. Press and release the “CH” button to select “DST 0” or “DST

1.”

4. “DST 0” indicates that the feature is off and the WWVB will
not change times automatically. “DST 1” indicates that the
feature is on and the WWVB will change times automatically.

Some locations (Arizona and parts of Indiana) do not

Note:

follow Daylight Saving Time and should select “DST 0.”

8