K 6.85 M
Operating
Instructions
Before first use of the
unit read these operating
instructions and act in
accordance with them.
5.962-612.0 (02/08)
Contents
General information 2
Safety instructions 3
Operation 4
Maintenance and care 8
Troubleshooting 9
Customer Service 10
Technical specifications 10
Assembly 12
Spare Parts 15
Environmental protection
The packaging material can be recycled. Please do not place the packaging into the ordinary refuse for
disposal, but arrange for the proper
recycling.
Old appliances contain valuable materials that can be recycled. Please
arrange for the proper recycling of old
appliances. Please dispose your old
appliances using appropriate collection systems
General information
Dear Customer,
Please read and comply with
these instructions prior to the initial operation of your appliance. Retain
these operating instructions for future reference or for subsequent possessors.
Hazard levels
Danger
Immediate danger that can cause severe
injury or even death.
몇 Warning
Possible hazardous situation that could
lead to severe injury or even death.
Caution
Possible hazardous situation that could
lead to mild injury to persons or damage to
property.
Proper Use
This high-pressure cleaner is designed for
domestic use only:
– to clean machines, vehicles, buildings,
tools, facades, terraces, garden equipment etc. using a high-pressure water
jet (and detergents if required).
– with accessories, replacement parts
and detergents approved by Kärcher.
Observe the instructions provided with
these detergents.
Warranty
The warranty terms published by our competent sales company are applicable in
each country. We will repair potential failures of your appliance within the warranty
period free of charge, provided that such
failure is caused by faulty material or defects in fabrication. In the event of a warranty claim please contact your dealer or the
nearest authorized Customer Service center. Please submit the proof of purchase.
(See address on the reverse)
Safety Devices
Caution
Safety devices protect the user and must
not be modified or bypassed.
Power switch
The appliance switch prevents unintentional operation of the appliance.
Lock trigger gun
This lock locks the lever of the trigger gun
and prevents the inadvertent start of the appliance.
2 English
Safety instructions
Danger
Never touch the mains plug and the
socket with wet hands.
The appliance must not be used if the
power cord or important parts of the appliance, e.g. high-pressure hoses, trigger gun or safety devices are damaged.
Check the power cord with mains plug
for damage before every use. If the
power cord is damaged, please arrange
immediately for the exchange by an authorized customer service or a skilled
electrician.
Check the high-pressure hose for dam-
age before every use. Please arrange
for the immediate exchange of a damaged high-pressure hose.
The appliance may not be used in areas
where a risk of explosion is present.
If the appliance is used in hazardous ar-
eas (e.g. filling stations) the corresponding safety provisions must be
observed.
High-pressure jets can be
dangerous if improperly
used. The jet must not be
directed at persons, animals, live electrical equipment or at the
appliance itself.
The high-pressure jet must not be di-
rected at other persons or directed by
the user at him/herself to clean clothing
or footwear.
Never use the appliance to clean ob-
jects containing hazardous substances
(e.g. asbestos).
Vehicle tyres or tyre valves are suscep-
tible to damage from the high-pressure
jet and may burst. The first indication of
this is a discolouration of the tyre. Damaged vehicle tyres/tyre valves are highly dangerous. Ensure that a distance of
at least 30 cm is observed when cleaning with the jet!
Never draw in fluids containing solvents
or undiluted acids and solvents! This includes petrol, paint thinner and heating
oil. The spray mist thus generated is
highly inflammable, explosive and poisonous. Do not use acetone, undiluted
acids and solvents as they are aggressive towards the materials from which
the appliance is made.
몇 Warning
The mains plug and the coupling of an
extension cable must be watertight and
must never lay in the water.
Unsuitable extension cables can be
hazardous. Only use extension cables
outdoors which have been approved for
this purpose and labelled with a sufficient cable cross-section:
1 - 10 m: 1.5 mm
Always fully unroll electrical cables from
the cable drum.
High-pressure hoses, fixtures and cou-
plings are important for the safety of the
appliance. Only use high-pressure hoses, fixtures and couplings recommended by the manufacturer.
This device is not intended for use by
persons (including children) with reduced physical, sensory or mental abilities or lacking experience and/or
knowledge, unless they are supervised
by a person responsible for their safety
or are instructed by these persons on
the use of the device. Children should
be supervised, to ensure that they do
not play with the device.
The operator must use the appliance
correctly. When working with the appliance, he must consider the local conditions and pay due care and attention to
other persons, in particular children,
who are nearby.
Do not use the appliance when there
are other persons around unless they
are also wearing safety equipment.
Wear protective clothing and safety
goggles to protect against splash back
containing water or dirt.
2
; 10 - 30 m: 2.5 mm
2
English 3
Caution
Observe a distance of at least 30 cm
when using the jet to clean painted surfaces to avoid damaging paintwork.
Never leave the appliance unattended
when it is in operation.
Make sure that the power cable or ex-
tension cables are not damaged by running over, pinching, dragging or similar.
Protect the power cable from heat, oil,
and sharp edges.
All current-conducting parts in the work-
ing area must be protected against jet
water.
The appliance may only be connected
to an electrical supply which has been
installed in accordance with IEC 60364.
The appliance may only be connected
to alternating current. The voltage must
correspond with the type plate on the
appliance.
The maximum tolerable mains imped-
ance at the electrical contact point (see
Technical Data) must not be exceeded.
For safety reasons, we recommend that
you operate the appliance only via a
earth-leakage circuit breaker (max.
30 mA).
Cleaning operations which produce oily
waste water, e.g. engine washes, underbody washes, may only be carried
out using washing stations equipped
with an oil separator.
This appliance was designed to be
used with detergents which are supplied or recommended by the manufacturer. The use of other detergents or
chemicals may compromise the safety
of the appliance.
Operation
Description of the Appliance
When unpacking the product, make sure
that no accessories are missing and that
none of the package contents have been
damaged. If you detect any transport damages please contact your dealer.
Illustrations on Page 5
1 Coupling element for water connection
2 Waterfilter
3 Fine filter in the water connection
4 Storage for accessories
5 Water connection
6 Appliance switch "0/OFF“/ „I/ON“
7 Storage for trigger gun
8 Transport handle
9 Detergent suction hose (with filter)
10 Dosage regulator for detergent
11 Detergent Tank
12 Storage for mains connection cable
13 Mains cable with mains plug
14 Storage for spray lance
15 Hose drum
16 hand crank for hose drum
17 Bearing wheel
18 High pressure hose
19 Trigger gun
20 Lock trigger gun
21 Key to detach the high-pressure hose
from the trigger gun
22 Spray lance with pressure regulation
(Vario Power)
23 Storage for accessories
Special accessories
Special accessories expand the possibilities of using your appliance. Please contact
your KÄRCHER dealer for further information.
4 English
Assembly see page 12 - 13
English 5
Before Startup Water supply
Mount loose parts delivered with appliance
prior to start-up.
Assemble appliance as shown on
page 12 and 13.
Î Illustration
Insert holder for trigger gun.
Î Illustration
Insert the transport handle and screw
in.
Î Illustration
Lock the detergent tank in place on the
appliance.
Close the detergent tank with the lid.
Î Illustration
Attach the accessories holder.
Î Illustration
Push the high pressure hose into the
trigger gun until it locks audibly.
Note: Make sure the connection nipple
is aligned correctly.
Check the secure connection by pulling
on the high-pressure hose.
According to the applicable regulations, the appliance must never be
used on the drinking water supply
without a system separator. Use a
suitable system separator manufactured by
KÄRCHER; or, as an alternative, a system
separator as per EN 12729 Type BA.
Note: Impurities in the water can damage
the high-pressure pump and accessories.
For protection, the use of the KÄRCHER
water filter (optional accessory, order no.
4.730-059) is recommended.
Water supply from mains
Observe regulations of water supplier.
For connection values, see type plate/technical data.
Î Use a fibre-reinforced water hose (not
included) with a standard coupling.
(Minimum diameter 1/2 inch (13 mm),
minimum length 7.5 m).
Î Screw the water filter on the water con-
nection of the device.
Î Screw the delivered coupling part on
the water filter.
Î Push the water supply hose onto the
coupling unit, then connect it to the tap.
Drawing in water from open reservoirs
This high-pressure cleaner is suited to work
with the KÄRCHER suction hose with backflow valve (Optional accessory, order no.
4.440-238) to draw in surface water, e.g.
from water butts or ponds (see specifications for max. suction height).
Î Fill the KÄRCHER suction hose with
backflow valve with water, screw to water supply and hang into he water butt.
Î Remove air from appliance before oper-
ation.
Switch on the appliance without mounted spray lance and run it until the water
discharging from the trigger gun is free
of bubbles. Switch off appliance and
connect spray lance.
6 English
Start up
Caution
Use the high pressure cleaner only when
you have mounted the water filter.
Never operate the high-pressure cleaner
when the tap is turned off as dry running will
damage the high-pressure pump.
Î Unwind the high pressure hose from the
hose drum.
Î Push the spray lance into the trigger
gun and fasten it by turning it through
90°.
Î Completely open the water tap.
Î Insert the mains plug into the socket.
Î Turn on the appliance “I/ON”.
Operation
몇 Danger
The trigger gun is subjected to a recoil force
when the water jet is discharged. Make
sure that you have a firm footing and are
also holding the trigger gun and spray lance
firmly.
Î Illustration (see page 13)
Unlock the lever on the trigger gun.
Î Pull on the lever of the trigger gun; the
device will switch on.
Note: Release the lever of the trigger gun;
the device will switch off again. High pressure remains in the system.
Spray lance with pressure regulation
Carrying out the most common cleaning
tasks. The work pressure can be stagelessly regulated between "Min" and "Max".
Î Release the lever on the trigger gun.
Î Turn the spray lance to the desired po-
sition.
Spray lance with dirt blaster
For particularly dirty items or areas.
Not suitable for use with detergents.
Working with detergent
We recommend the KÄRCHER cleaning
and care program that will match the respective cleaning requirements. Please
seek consultation or request information on
the subject.
Î Fill the detergent solution in the deter-
gent tank (observe dosage instructions
on the packaging of the detergent).
Î Adjust the suction volume of the deter-
gent solution by means of the dosage
regulator for detergents.
- Medium quantity: Central position
- Large quantity: "+" position
- Small quantity: "-" position
Î Use spray lance with pressure regula-
tion (Vario Power).
Î Turn the spray lance to "Mix" position.
Note: This will mix the detergent with
the water stream.
Recommended cleaning method
Î Spray the detergent sparingly on the
dry surface and allow it to react, but not
to dry.
Î Spray off loosened dirt with the high-
pressure ray.
Interrupting operation
Î Release the lever on the trigger gun.
Î Illustration (see page 13)
Lock the lever on the trigger gun.
Î During longer breaks (more than 5 min-
utes), also turn the appliance off using
the "0/OFF" switch.
Î Insert the trigger gun in its holder.
English 7
Finish operation
Maintenance and care
Caution
Only separate the high-pressure hose from
the trigger gun or the appliance while there
is no pressure in the system.
Î After operation with detergent: Fill the
detergent tank with clear water, turn the
spray pipe with pressure regulator to
the position "Mix", switch the appliance
on for about 1 minute and rinse with
clear water.
Î Release the lever on the trigger gun.
Î Turn off the appliance "0/OFF".
Î Turn off tap.
Î Detach the appliance from the water
supply.
Î Press the lever on the trigger gun to re-
lease any remaining pressure in the
system.
Î Illustration (see page 13)
Lock the lever on the trigger gun.
Î Pull out the mains plug.
Î Roll up the power cord and loop it e.g.
round the handle.
Î Roll the high pressure hose on to the
hose drum: Pull out the hose drum han-
dle, turn it clockwise then retract the
handle.
Î Insert the trigger gun in its holder.
Transport
Caution
Empty the detergent tank before transporting in horizontal position.
Danger
Turn off the appliance and remove the
mains plug prior to any care and maintenance work.
Maintenance
The appliance is maintenance-free.
Storage
Prior to longer periods of storage, e.g. in
the winter:
Î Completely drain all water from the ap-
pliance: Switch the appliance on with
detached high-pressure hose and detached water supply (max. 1 minute)
and wait, until no more water exits at the
high-pressure connection. Turn off the
appliance.
Î Remove filter from suction hose for de-
tergent and clean under running water.
Î Pull out the fine filter in water connec-
tion using flat-nose pliers and clean with
running water.
Frost protection
Caution
Protect the appliance and its accessories
against frost.
The appliance and its accessories can get
destroyed through frost if there are any water residues in them. To avoid damage to
them:
Î Store the appliance and the entire ac-
cessories in a frost-safe room.
8 English
Spare parts
Use only original KÄRCHER spare parts.
You will find a list of spare parts at the end
of these operating instructions.
Troubleshooting
You can rectify minor faults yourself with
the help of the following overview.
If in doubt, please consult the authorized
customer service.
Danger
Turn off the appliance and remove the
mains plug prior to any care and maintenance work.
Repair works may only be performed by the
authorized customer service.
Appliance is not running
Î Check whether the voltage indicated on
the type plate corresponds to the volt-
age of the mains supply.
Î Check the mains connection cable for
damages.
Pressure does not build up in the
appliance
Î Check setting at the spray lance.
Î Remove air from appliance before oper-
ation.
Switch on the appliance without mount-
ed spray lance and run it until the water
discharging from the trigger gun is free
of bubbles. Switch off appliance and
connect spray lance.
Î Check the water supply.
Î Pull out the fine filter in water connec-
tion using flat-nose pliers and clean with
running water.
Strong pressure fluctuations
Î Clean high-pressure nozzle: Remove
dirt and debris from the nozzle bore, using a needle and rinse through with water from the front.
Î Check water flow quantity.
Appliance is leaking
Î Slight leakage from the appliance pump
is normal. If the leakage increases contact the authorized customer service.
No detergent infeed
Î Use spray lance with pressure regula-
tion (Vario Power).
Turn the spray lance to "Mix" position.
Î Check the settings at the detergent dos-
aging regulator.
Î Clean the detergent suction hose filter.
Î Check the detergent suction hose for
kinks.
Appliance does not start, motor hums
Cause: Voltage reduction due to weak
mains supply or when using an extension
cable.
Î When switching on, first pull the lever of
the trigger gun and then switch the ap-
pliance switch to "I/ON".
English 9
Customer Service Technical specifications
Australia
Kärcher Pty. Ltd.
40 Koornang Road
Scoresby, Victoria 3179
1800 675 714 (Free Call)
www.karcher.com.au
Power connection
Voltage 230-240
1~50VHz
Connected load 2,2 kW
Mains fuse (slow-blow) 16 A
Maximum allowed net im-
pedance
Protective class I
Protection class IP X5
Water connection
Max. feed temperature 60 °C
Min. feed volume 11 I/min
Max. feed pressure 0,6 MPa
Max. Suction height 0,5 m
Performance data
Working pressure 13 MPa
Max. permissible pressure 15 MPa
Water flow rate 8,2 I/min
Detergent flow rate 0-0,2 I/min
Recoil force of trigger gun 21 N
Hand-arm vibration
(ISO 5349)
Sound pressure level
LpA (EN60704-1)
Sound power level
LWA (2000/14/EG)
Dimensions
Length 400 mm
Width 395 mm
Height 925 mm
Weight 19 kg
0,388
+ j0,243
0,8 m/s
73 dB(A)
92 dB(A)
Ohm
Ohm
2
10 English
Subject to technical modifications!
Notes
English 11
Assembly
12 English
Assembly
English 13
Notes
14 English
Spare Parts
English 15
Loading...