Kyocera M3860IDNF, M3860IDN User Manual

Download

kyoceradocumentsolutions.com

Operation Guide

ECOSYS M3860idnf ECOSYS M3860idn

> Preface

Preface

Thank you for purchasing this machine.

This Operation Guide is intended to help you operate the machine correctly, perform routine maintenance, and take simple troubleshooting measures as needed so that the machine can always be used in the optimum condition.

Please read this Operation Guide before using the machine.

To maintain quality, we recommend using genuine Kyocera toner containers, which must pass numerous quality inspections.

The use of non-genuine toner containers may cause failure.

We will not be liable for any damages caused by the use of third party supplies in this machine.

A label is affixed to our replacement genuine toner containers, as shown below.

Checking the Equipment's Serial Number

The equipment's serial number is printed in the location shown in the figure.

You'll need the equipment's serial number when contacting your Service Representative. Please check the number before contacting your Service Representative.

Preface ..................................................................................................................................... i

Contents.................................................................................................................................. ii

Overview ................................................................................................................................ ix

Machine Features ................................................................................................................... x

Color and Image Quality Functions ................................................................................... xiv

Basic Color Modes ...................................................................................................... xiv

Adjusting Image Quality and Color............................................................................... xv

Guides Provided with the Machine.................................................................................... xvi

About the Operation Guide (this Guide) ......................................................................... xviii

Structure of the guide................................................................................................. xviii

Conventions Used in This Guide................................................................................. xix

Menu Map............................................................................................................................. xxi

1 Legal and Safety Information ................................................................ 1-1

Notice ................................................................................................................................. 1-2

Safety Conventions in This Guide ............................................................................. 1-2

Environment .............................................................................................................. 1-3

Precautions for Use ................................................................................................... 1-4

Laser Safety (Europe) ............................................................................................... 1-5

SAFETY OF LASER BEAM (USA) ........................................................................... 1-6

Safety Instructions Regarding the Disconnection of Power ...................................... 1-7

Compliance and Conformity ...................................................................................... 1-7

Other precautions (for users in California, the United States) ................................... 1-7

Warranty (the United States and Canada) ................................................................ 1-8

Legal Restriction on Copying/Scanning .................................................................... 1-9

EN ISO 7779 ............................................................................................................. 1-9

EK1-ITB 2000 ............................................................................................................ 1-9

Wireless Connection (Mexico only) ........................................................................... 1-9

Security Precautions when Using Wireless LAN (If equipped) ................................. 1-9

Limited Use of This Product (If equipped) ............................................................... 1-10

Legal Information .................................................................................................... 1-11

Energy Saving Control Function ............................................................................. 1-17

Automatic 2-Sided Print Function ............................................................................ 1-17

Resource Saving - Paper ........................................................................................ 1-17

Environmental benefits of "Power Management" .................................................... 1-17

Energy Star (ENERGY STAR®) Program ............................................................... 1-18

2 Installing and Setting up the Machine .................................................. 2-1

Part Names ......................................................................................................................... 2-2

Machine Exterior ....................................................................................................... 2-2

Connectors/Interior .................................................................................................... 2-6

With Optional Equipments Attached ....................................................................... 2-10

Connecting the Machine and Other Devices ................................................................ 2-12

Connecting Cables .......................................................................................................... 2-13

Connecting LAN Cable ............................................................................................ 2-13

Connecting USB Cable ........................................................................................... 2-14

Connecting the Power Cable .................................................................................. 2-14

Power On/Off ................................................................................................................... 2-15

Power On ................................................................................................................ 2-15

Power Off ................................................................................................................ 2-15

Using the Operation Panel ............................................................................................. 2-16

Operation Panel Keys ............................................................................................. 2-16

Adjusting the Operation Panel Angle ...................................................................... 2-17

Touch Panel ..................................................................................................................... 2-18

Home Screen .......................................................................................................... 2-18

Display for Device Information ................................................................................ 2-22

Functions key .......................................................................................................... 2-23

Display of Keys That Cannot Be Set ....................................................................... 2-24

Enter key and Quick No. Search key ...................................................................... 2-25

Help Screen ............................................................................................................ 2-26

Login/Logout ................................................................................................................... 2-27

Login ....................................................................................................................... 2-27

Logout ..................................................................................................................... 2-28

Default Settings of the Machine ..................................................................................... 2-29

Setting Date and Time ............................................................................................ 2-29

Network Setup ................................................................................................................. 2-30

Configuring the Wired Network ............................................................................... 2-30

Configuring the Wireless Network ........................................................................... 2-32

Setting Wi-Fi Direct ................................................................................................. 2-36

Energy Saver function .................................................................................................... 2-38

Low Power Mode .................................................................................................... 2-38

Sleep and Auto Sleep ............................................................................................. 2-38

Power Off Rule (models for Europe) ....................................................................... 2-39

Quick Setup Wizard ......................................................................................................... 2-40

Installing Software .......................................................................................................... 2-42

Software on DVD (Windows) .................................................................................. 2-42

Installing Software in Windows ............................................................................... 2-43

Uninstalling the Software ........................................................................................ 2-49

Installing Software in Mac Computer ...................................................................... 2-50

Setting TWAIN Driver .............................................................................................. 2-52

Setting WIA Driver ................................................................................................... 2-54

Checking the Counter ..................................................................................................... 2-55

Additional Preparations for the Administrator ............................................................. 2-56

Sending Documents to a PC ................................................................................... 2-56

Strengthening the Security ...................................................................................... 2-56

Command Center RX ...................................................................................................... 2-58

Accessing Command Center RX ............................................................................ 2-59

Changing Security Settings ..................................................................................... 2-60

Changing Device Information .................................................................................. 2-62

E-mail Settings ........................................................................................................ 2-64

Registering Destinations ......................................................................................... 2-68

Creating a New Custom Box ................................................................................... 2-69

Printing a document stored in a Custom Box .......................................................... 2-70

Transferring Data from Our Other Products ................................................................. 2-72

Migrating the Address Book .................................................................................... 2-72

3 Preparation before Use .......................................................................... 3-1

Loading Paper ................................................................................................................... 3-2

Precaution for Loading Paper ................................................................................... 3-3

Loading in the Cassettes ........................................................................................... 3-4

Loading Statement in the Cassettes (For inch models) ............................................ 3-8

Loading Paper in the Multi Purpose Tray ................................................................ 3-11

Specifying Paper Size and Media Type .................................................................. 3-15

Paper Stopper .................................................................................................................. 3-17

Preparation for Sending a Document to a Shared Folder in a PC .............................. 3-18

Making a Note of the Computer Name and Full Computer Name .......................... 3-18

Making a Note of the User Name and Domain Name ............................................. 3-19

Creating a Shared Folder, Making a Note of a Shared Folder ................................ 3-20

Configuring Windows Firewall ................................................................................. 3-24

Turn off password-protected sharing (Windows 10 only) ........................................ 3-28

Registering Destinations in the Address Book ............................................................ 3-30

Adding a Destination (Address Book) ..................................................................... 3-30

Adding a Destination on One Touch Key (One Touch Key) .................................... 3-35

iii

4 Printing from PC ..................................................................................... 4-1

Printing from PC ................................................................................................................ 4-2

Printing on Non-standard Sized Paper ...................................................................... 4-4

Banner printing .......................................................................................................... 4-5

Printer Driver Print Settings Screen .......................................................................... 4-9

Printer Driver Help ................................................................................................... 4-10

Changing the Default Printer Driver Settings (Windows 8.1) .................................. 4-10

Canceling Printing from a Computer ....................................................................... 4-10

Printing by AirPrint ......................................................................................................... 4-11

Printing by Google Cloud Print ...................................................................................... 4-11

Printing by Mopria ........................................................................................................... 4-11

Printing with Wi-Fi Direct ................................................................................................ 4-11

Printing Data Saved on the Printer ................................................................................ 4-12

Specifying the Job Box from a Computer and Storing the Job ............................... 4-12

Printing Documents from Private Print Box ............................................................. 4-13

Printing Document from Stored Job Box ................................................................. 4-15

Printing Document from Quick Copy Box ................................................................ 4-17

Printing Document from Proof and Hold Box .......................................................... 4-19

Status Monitor ................................................................................................................. 4-21

Accessing the Status Monitor .................................................................................. 4-21

Exiting the Status Monitor ....................................................................................... 4-21

Status Monitor Display ............................................................................................ 4-21

5 Operation on the Machine ..................................................................... 5-1

Loading Originals .............................................................................................................. 5-2

Placing Originals on the Platen ................................................................................. 5-2

Loading Originals in the Document Processor .......................................................... 5-3

Favorites ............................................................................................................................ 5-6

Registering Favorite .................................................................................................. 5-7

Recalling Favorite ..................................................................................................... 5-9

Editing and Deleting Favorite .................................................................................. 5-10

Application ....................................................................................................................... 5-11

Installing Applications .............................................................................................. 5-11

Using Applications ................................................................................................... 5-12

Uninstalling Applications ......................................................................................... 5-13

Registering Shortcuts ..................................................................................................... 5-14

Adding Shortcuts ..................................................................................................... 5-14

Editing and Deleting Shortcuts ................................................................................ 5-15

Copying ............................................................................................................................ 5-16

Basic Operation ....................................................................................................... 5-16

Canceling Jobs ........................................................................................................ 5-17

Sending ............................................................................................................................ 5-18

Basic Operation ....................................................................................................... 5-19

Specifying Destination ............................................................................................. 5-20

Checking and Editing Destinations ......................................................................... 5-25

Confirmation Screen of Destinations ....................................................................... 5-26

Recall ...................................................................................................................... 5-27

Send to Me (E-mail) ................................................................................................ 5-27

Sending to Different Types of Destinations (Multi Sending) .................................... 5-28

Canceling Sending Jobs ......................................................................................... 5-29

WSD Scan ............................................................................................................... 5-30

Installing the Driver ................................................................................................. 5-30

Scanning using TWAIN or WIA ............................................................................... 5-32

Scanning with File Management Utility ................................................................... 5-33

Using fax server to send a fax (fax server transmission) ............................................ 5-34

Configuring Settings before Sending ...................................................................... 5-34

Using fax server to send a fax ................................................................................. 5-34

How to use the FAX Function ........................................................................................ 5-36

What is Document Box? ................................................................................................. 5-37

Basic Operation for Document Box ............................................................................... 5-38

Box List Operations ................................................................................................. 5-38

Document List Operations ....................................................................................... 5-38

Using a Custom Box ....................................................................................................... 5-39

Creating a New Custom Box ................................................................................... 5-39

Editing and Deleting Custom Box ........................................................................... 5-41

Saving Scanned Documents to a Custom Box ....................................................... 5-42

Moving Documents in Custom Box ......................................................................... 5-43

Copying Documents in Custom Box into Other Boxes ............................................ 5-43

Copying Documents in Custom Box to USB Drive .................................................. 5-44

Joining Documents in Custom Box ......................................................................... 5-45

Deleting Documents in Custom Box ....................................................................... 5-46

Printing Documents in Custom Box ........................................................................ 5-46

Sending Documents in a Custom Box .................................................................... 5-47

Sending Documents in Custom Box to E-mail Address of Logged in user. ............ 5-48

Scanning Document Stored in a Custom Box ......................................................... 5-49

Printing Documents Stored in USB Drive ..................................................................... 5-50

Saving Documents to USB Drive (Scan to USB) .......................................................... 5-52

Check the USB Drive Information .................................................................................. 5-53

Removing USB Drive ...................................................................................................... 5-54

Using the Manual Stapler

(ECOSYS M3860idn only) ............................................................................................... 5-55

6 Using Various Functions ....................................................................... 6-1

Functions Available on the Machine ............................................................................... 6-2

Copy .......................................................................................................................... 6-2

Send .......................................................................................................................... 6-4

Custom Box (Store File, Printing Documents, Sending Documents) ........................ 6-6

USB Drive (Store File, Printing Documents) ............................................................. 6-8

Functions ......................................................................................................................... 6-10

ID Card Copy .......................................................................................................... 6-10

Original Size ............................................................................................................ 6-10

Paper Selection ....................................................................................................... 6-11

Original Orientation ................................................................................................. 6-12

Mixed Size Originals ............................................................................................... 6-13

Collate/Offset .......................................................................................................... 6-13

Paper Output ........................................................................................................... 6-14

Staple ...................................................................................................................... 6-14

Density .................................................................................................................... 6-15

Original Image ......................................................................................................... 6-16

EcoPrint ................................................................................................................... 6-17

Color Selection ........................................................................................................ 6-17

Sharpness ............................................................................................................... 6-18

Contrast ................................................................................................................... 6-18

Background Density Adj. (Background Density Adjustment) .................................. 6-19

Prevent Bleed-thrugh .............................................................................................. 6-19

Zoom ....................................................................................................................... 6-20

Combine .................................................................................................................. 6-22

Duplex ..................................................................................................................... 6-24

Continuous Scan ..................................................................................................... 6-26

Job Finish Notice ..................................................................................................... 6-26

File Name Entry ...................................................................................................... 6-27

Priority Override ...................................................................................................... 6-27

Quiet Mode .............................................................................................................. 6-27

Skip Blank Page ...................................................................................................... 6-28

Duplex (2-sided Original) ........................................................................................ 6-29

Sending Size ........................................................................................................... 6-30

File Format .............................................................................................................. 6-31

File Separation ........................................................................................................ 6-35

Scan Resolution, Resolution ................................................................................... 6-35

E-mail Subject/Body ................................................................................................ 6-35

Long Original ........................................................................................................... 6-36

FTP Encrypted TX ................................................................................................... 6-36

Delete after Printed ................................................................................................. 6-36

Delete after Transmitted .......................................................................................... 6-36

Storing Size ............................................................................................................. 6-37

Encrypted PDF Password ....................................................................................... 6-37

JPEG/TIFF Print ...................................................................................................... 6-38

XPS Fit to Page ....................................................................................................... 6-38

7 Status/Job Cancel .................................................................................. 7-1

Checking Job Status ......................................................................................................... 7-2

Details of the Status Screens .................................................................................... 7-3

Checking Detailed Information of Jobs ..................................................................... 7-7

Checking Job History ....................................................................................................... 7-8

Checking the Detailed Information of Histories ......................................................... 7-9

Sending the Log History ............................................................................................ 7-9

Job Operation .................................................................................................................. 7-10

Pause and Resumption of Jobs .............................................................................. 7-10

Canceling of Jobs .................................................................................................... 7-10

Device/Communication ................................................................................................... 7-11

Checking the Remaining Amount of Toner and Paper (Paper/Supplies) ................... 7-13

8 Setup and Registration (System Menu) ............................................... 8-1

System Menu ..................................................................................................................... 8-2

Operation Method ..................................................................................................... 8-2

System Menu Settings .............................................................................................. 8-3

Language .................................................................................................................. 8-5

Report ....................................................................................................................... 8-5

User Property ............................................................................................................ 8-7

Cassette/MP Tray Settings ....................................................................................... 8-8

Common Settings .................................................................................................... 8-10

Home ....................................................................................................................... 8-21

Copy ........................................................................................................................ 8-21

Send ........................................................................................................................ 8-22

Document Box ......................................................................................................... 8-23

FAX ......................................................................................................................... 8-23

Application ............................................................................................................... 8-23

Internet .................................................................................................................... 8-24

Address Book/One Touch ....................................................................................... 8-24

User Login/Job Accounting ..................................................................................... 8-25

Printer ...................................................................................................................... 8-25

System/Network ...................................................................................................... 8-28

Date/Timer/Energy Saver ........................................................................................ 8-49

Adjustment/Maintenance ......................................................................................... 8-52

User Authentication and Accounting (User Login, Job Accounting)

Overview of User Login Administration .......................................................................... 9-2

Enabling User Login Administration ............................................................................... 9-3

Setting User Login Administration .................................................................................. 9-4

Authentication Security ............................................................................................. 9-4

Adding a User (Local User List) ................................................................................ 9-6

Changing User Properties ......................................................................................... 9-9

User Login Administration for Printing ..................................................................... 9-13

... 9-1

To Manage the Users to Scan Using TWAIN .......................................................... 9-15

To Manage the Users to Scan Using WIA .............................................................. 9-16

To Manage the Users that Send Faxes from a PC ................................................. 9-17

Local Authorization .................................................................................................. 9-18

Group Authorization Settings .................................................................................. 9-19

Guest Authorization Set. ......................................................................................... 9-22

Obtain NW User Property ....................................................................................... 9-25

Simple Login Settings ............................................................................................. 9-27

ID Card Settings ...................................................................................................... 9-30

PIN Code Authorization ........................................................................................... 9-31

Using User Login Administration .................................................................................. 9-32

Login/Logout ........................................................................................................... 9-32

Overview of Job Accounting .......................................................................................... 9-33

Enabling Job Accounting ............................................................................................... 9-34

Job Accounting Access ........................................................................................... 9-35

Setting an Account .......................................................................................................... 9-36

Adding an Account .................................................................................................. 9-36

Restricting the Use of the Machine ......................................................................... 9-37

Editing an Account .................................................................................................. 9-38

Deleting an Account ................................................................................................ 9-39

Job Accounting for Printing ..................................................................................... 9-40

Job Accounting for Scan Using TWAIN .................................................................. 9-41

Job Accounting for Scan Using WIA ....................................................................... 9-42

Job Accounting for the FAX Transmitted from a Computer .................................... 9-43

Configuring Job Accounting .......................................................................................... 9-44

Default Setting ......................................................................................................... 9-44

Counting the Number of Pages Printed .................................................................. 9-45

Print Accounting Report .......................................................................................... 9-46

Using Job Accounting .................................................................................................... 9-47

Login/Logout ........................................................................................................... 9-47

Unknown User Settings .................................................................................................. 9-48

Unknown ID Job ...................................................................................................... 9-48

Registering Information for a User whose ID is Unknown ....................................... 9-49

10 Troubleshooting ................................................................................... 10-1

Regular Maintenance ...................................................................................................... 10-2

Cleaning .................................................................................................................. 10-2

Toner Container Replacement ................................................................................ 10-6

Waste Toner Box Replacement ............................................................................ 10-10

Replacing Staples ................................................................................................. 10-12

Troubleshooting ............................................................................................................ 10-14

Solving Malfunctions ............................................................................................. 10-14

Responding to Messages ...................................................................................... 10-19

Adjustment/Maintenance ....................................................................................... 10-30

Clearing Paper Jams ............................................................................................. 10-31

Clearing a Staple Jam ........................................................................................... 10-39

11 Appendix ............................................................................................... 11-1

Optional Equipment ........................................................................................................ 11-2

Overview of Optional Equipment ............................................................................. 11-2

Optional Applications .............................................................................................. 11-8

Character Entry Method ................................................................................................ 11-10

Entry Screens ........................................................................................................ 11-10

Entering Characters .............................................................................................. 11-12

Paper .............................................................................................................................. 11-13

Basic Paper Specifications .................................................................................... 11-13

Choosing the Appropriate Paper ........................................................................... 11-14

Special Paper ........................................................................................................ 11-17

vii

Specifications ................................................................................................................ 11-21

Machine ................................................................................................................. 11-21

Copy Functions ..................................................................................................... 11-23

Printer Functions ................................................................................................... 11-24

Scanner Functions ................................................................................................ 11-25

Document Processor ............................................................................................. 11-25

Paper Feeder (500-sheet) (Option) ....................................................................... 11-26

Manual Stapler (ECOSYS M3860idn only) ........................................................... 11-26

Glossary ......................................................................................................................... 11-27

Index ............................................................................................................................ Index-1

viii

> Overview

NOTE

Original Electronic data Fax dataUSB drive

Input Data

Operations from your PC

Document

Box functions

Application

Security

Output Data

Copy functions Printer functions

USB driveSend functions

Fax functions

Wi-Fi connection

FAX Operation Guide

This function is useful for a variety of purposes, including saving data in the machine and in a USB drive stick.

Printing Data Saved on the Printer (page 4-12) Using a Custom Box (page 5-39)

You can expand the machine functions according to your needs.

Application (page 5-11)

You can use the machine security levels according to your needs.

Sending (page 5-18)

Command Center RX

You can check the status and change the settings of the machine from a Web browser on your computer.

Command Center RX (page 2-58)

Command Center RX User Guide

Strengthen security (page xii)

Copying (page 5-16) Printing from PC (page 4-1)

Saving Documents to USB Drive (Scan to USB) (page 5-52)

Wi-Fi or Wi-Fi Direct connection is possible.

Configuring the Wireless Network (page 2-32)

Overview

This machine is equipped standard with copy and print functions, and a scanned image can be sent to an E-mail recipient as an attachment or to a computer on the same network.

• Before using the machine, be sure to read the following:

Legal and Safety Information (page 1-1)

• For preparations for use of the machine such as cable connections and software installation, refer to the following:

Installing and Setting up the Machine (page 2-1)

• To learn how to load paper, set up shared folders, and add addresses to the address book, refer to the following:

Preparation before Use (page 3-1)

> Machine Features

1 2 3

1~10

1~30

11~201121~30

Machine Features

The machine is equipped with many useful functions.

Using Various Functions (page 6-1)

Here are some examples.

Optimize your office workflow

Access to frequently used functions with just one touch (Favorites)

You can preset frequently used functions.

Once you register frequently used settings as favorite, you can call up the settings easily. Using this favorite brings the same results even if operated by another person.

Favorites (page 5-6)

Optimize your office workflow

Scan a large number of originals in separate batches and produce as one job (Continuous Scan)

Set up the machine easily (Quick Setup Wizard)

You can configure the necessary settings before using the machine in the wizard mode.

Quick Setup Wizard (page 2-40)

Send one time with multiple sending options (Multi Sending)

Set up fax easily (FAX Setup)

You can configure the necessary settings before using fax in the wizard mode.

FAX Setup (page 2-40)

Save frequently used documents in the machine (Custom Box)

It is useful when preparing many-page handouts.

When a large number of originals cannot be placed in the document processor at one time, the originals can be scanned in separate batches and then copied or sent as one job.

Continuous Scan (page 6-26)

You can send a same document to the multiple destinations using a different method.

You can specify multiple destinations of different send methods such as E-mail, SMB, and Fax.

You can reduce your workflow by sending a job at once.

Sending to Different Types of Destinations (Multi Sending) (page 5-

28)

You can save the frequently used document in the machine and print it when needed.

Using a Custom Box (page 5-39)

> Machine Features

Optimize your office workflow Save energy and cost

Send a FAX from a PC (Sending FAX from PC)

You can save the paper used for sending a FAX with this function.

You can send a file to be faxed from the PC without printing the file, so that you can reduce the number of pieces of paper and perform sending jobs efficiently.

FAX Operation Guide

Save energy and cost

Save energy as needed (Energy Saver function)

Off

The machine is equipped with Energy Saver function that automatically switched into Sleep Mode.

Energy Saver function (page 2-38)

Use less toner for printing (EcoPrint)

You can save toner consumption with this function.

When you only need to check the printed content, such as a trial print run or documents for internal confirmation, use this function to save toner.

Use this function when a high-quality print is not required.

EcoPrint (page 6-17)

Reduce paper use (Paper Saving Printing)

You can print originals on both sides of the paper. You can also print multiple originals onto one sheet.

Favorites (page 5-6)

Skip blank pages when printing (Skip Blank Page)

When there are blank pages in a scanned document, this function skips the blank pages and prints only pages that are not blank.

Skip Blank Page (page 6-28)

Send a FAX to reduce the communication cost (FAX Delayed Transmission)

You can reduce the communication cost with this function.

The communication cost can be reduced by setting the timer to the time period during which the communication cost is low.

FAX Operation Guide

> Machine Features

OK !

Create attractive documents Strengthen security

Prevent image bleed-through (Prevent Bleed-through)

You can prevent image bleed-through from the reverse side when scanning thin originals.

Prevent Bleed-thrugh (page 6-19)

Strengthen security

Prevent loss of finished documents (Private Print)

Password-protect a PDF file (PDF Encryption Functions)

Use the PDF format's password security options to restrict document viewing, printing and editing.

Encrypted PDF Password (page 6-

37)

Protect data on the hard disk/SSD (Encryption / Overwrite)

You can overwrite the unnecessary data that remains on the hard disk/SSD automatically.

To prevent an external leakage, the machine is able to encrypt data before writing it to the hard disk/SSD.

Data Security (page 8-45)

Strengthen security (Settings for Administrator)

You can temporarily save a printer document in the machine. By printing the document from the machine prevents someone takes your document.

Printing Data Saved on the Printer (page 4-12)

You can log in simply by touching an ID card. You don't need to enter your user name and password.

Card Authentication Kit(B) "Card Authentication Kit" (page 11-4)

Various functions are available for administrators to strengthen security.

Strengthening the Security (page 2-

56)

xii

> Machine Features

Use functions more efficiently

Make the machine quiet (Quiet Mode)

You can make the machine quiet by reducing its running noise. You can configure this mode by job.

Quiet Mode (page 6-27)

Use functions more efficiently

Use USB drive (USB Drive)

Expand functions as necessary (Application)

The functionality of the machine can be expanded by installing applications.

Applications that help you perform your daily more efficiently such as a scan feature and an authentication feature are available.

Application (page 5-11)

Specify image file format (File Format)

Install the machine without concerning the network cables (Wireless Network)

In an environment where the wireless LAN is used, you can install the machine without concerning the network cables. In addition, Wi-Fi Direct, etc. are supported.

Configuring the Wireless Network (page 2-32)

Setting Wi-Fi Direct (page 2-36)

Perform remote operation (Command Center RX)

It is useful when you need to print document outside your office or you cannot print document from your PC.

You can print the document from the USB drive by plugging it directly into the machine.

Original scanned at the machine can be saved in the USB drive also.

Printing Documents Stored in USB Drive (page 5-50)

Saving Documents to USB Drive (Scan to USB) (page 5-52)

You can select the various file formats when sending/storing images.

File Format (page 6-31)

You can access to the machine remotely to print, send or download data.

Administrators can configure the machine behavior or management settings.

Command Center RX (page 2-58)

xiii

> Color and Image Quality Functions

Color and Image Quality Functions

The machine is equipped with various color and image quality functions. You can adjust the scanned image as desired.

Basic Color Modes

The basic color modes are as follows.

Color mode Description

Reference image

Before After

Auto Color Automatically recognizes whether a

document being scanned is color or black & white.

Full Color Scans a document in full color. page 6-17

Grayscale Scans a document in grayscale. page 6-17

Black & White Scans a document in black & white. page 6-17

For details, refer to the following:

Color Selection (page 6-17)

Reference

page

page 6-17

xiv

> Color and Image Quality Functions

Adjusting Image Quality and Color

To adjust the image quality or color of an image, use the following functions.

Sample image

I want to...

Before After

Adjust the color precisely.

Adjust the density. Density page 6-15

Adjust the image quality precisely

Function Page

Emphasize or blur the image outline.

Example: Emphasize the image outlines

Adjust the difference between dark and light parts of the image.

Darken or lighten the background (the area with no texts or images) of a document.

Example: Lightening the background

Prevent bleed-through in 2-sided originals.

Adjust the scanned image

Decrease the file size and produce the characters clearly.

Sharpness page 6-18

Contrast page 6-18

Background Density page 6-19

Prevent Bleedthrough

File format

[High Comp. PDF]

page 6-19

page 6-31

> Guides Provided with the Machine

Guides Provided with the Machine

The following guides are provided with the machine. Refer to each guide as needed.

The contents of the guides are subject to change without notice for the purpose of improvement of machine performance.

Printed guides

Start using the machine quickly

For safe use of the machine

Quick Guide

Explains how to use basic functions of the machine, how to use convenient features, how to perform routine maintenance, and what to do when problems occur.

Safety Guide

Provides safety and cautionary information for installation environment and use of the machine. Be sure to read this guide before using the machine.

Safety Guide (ECOSYS M3860idn/ECOSYS M3860idnf)

Indicates the space required for machine installation, and describes the cautionary labels and other safety information. Be sure to read this guide before using the machine.

xvi

> Guides Provided with the Machine

Guides (PDF) on the DVD (Product Library)

Use the machine thoughtfully

Use the fax functions

Use the ID card

Strengthen security

Easily register machine information and configure settings

Print data from a computer

Directly print a PDF file

Monitor the machine and printers on the network

Operation Guide (This Guide)

Explains how to load paper and perform copy, print and scan operations, and indicates default settings and other information.

FAX Operation Guide

Explains how to use the fax function.

Card Authentication Kit (B) Operation Guide

Explains how to perform authentication using the ID card.

Data Encryption/Overwrite Operation Guide

Explains how to introduce and use the Data Encryption/Overwrite, and how to overwrite and encrypt data.

Command Center RX User Guide

Explains how to access the machine from a Web browser on your computer to check and change settings.

Printer Driver User Guide

Explains how to install the printer driver and use the printer function.

KYOCERA Net Direct Print Operation Guide

Explains how to print PDF files without launching Adobe Acrobat or Reader.

KYOCERA Net Viewer User Guide

Explains how to monitor your network printing system (the machine) with KYOCERA Net Viewer.

Scan images and save with information

File Management Utility User Guide

Explains how to use File Management Utility to set various parameters and send and save scanned documents.

PRESCRIBE Commands Command Reference

Print without using the printer driver

Adjust the print or scan position

Install the following versions of Adobe Reader to view the manuals on the DVD. Version 8.0 or later

Describes the native printer language (PRESCRIBE commands).

PRESCRIBE Commands Technical Reference

Describes the PRESCRIBE command functions and control for each type of emulation.

Maintenance Menu User Guide

Maintenance Menu provides the explanation on how to configure the print, scan, and other settings.

xvii

> About the Operation Guide (this Guide)

About the Operation Guide (this Guide)

Structure of the guide

The Operation Guide contains the following chapters.

Chapter Contents

1 Legal and Safety Information Provides precautions regarding use of the machine and trademark information.

2 Installing and Setting up the

Machine

3 Preparation before Use Explains preparations and settings that are required in order to use the machine, such

4 Printing from PC Explains functions that are available when the machine is used as a printer.

5 Operation on the Machine Explains the basic procedures for using the machine, such as placing originals, making

6 Using Various Functions Explains convenient functions that are available on the machine.

7 Status/Job Cancel Explains how to check the status of a job and the job history, and how to cancel jobs

8 Setup and Registration (System

Menu)

9 User Authentication and

Accounting (User Login, Job Accounting)

10 Troubleshooting Explains what to do when toner runs out, an error is displayed, or a paper jam or other

11 Appendix Describes convenient options that are available for the machine. Provides information

Explains part names, cable connections, installation of the software, login, logout, and other matters related to administration of the machine.

as how to use the operation panel, load paper, and create an address book.

copies, sending documents, and using document boxes.

being printed or waiting to print. Also explains how to check paper and toner levels, how to check the device status, and how to cancel fax transmission.

Explains System Menu and how it relates to the operation of the machine.

Explains user login and job accounting.

problem occurs.

on media types and paper sizes, and gives a glossary of terms. Explains how to enter characters, and lists the specifications of the machine.

xviii

> About the Operation Guide (this Guide)

NOTE

Click to move from the current page to the previously displayed page. This is convenient when you want to return to the page from which you jumped to the current page.

Click an item in the Table of Contents to jump to the corresponding page.

CAUTION

Indicates that personal injury or mechanical damage may result from insufficient attention to or incorrect compliance with the related points.

NOTE

Indicates supplemental explanations and reference information for operations.

IMPORTANT

Indicates operational requirements and restrictions to operate the machine correctly, and avoid damage to the machine or property.

Refer to

Click the underlined text to jump to the corresponding page.

Conventions Used in This Guide

Adobe Reader XI is used as an example in the explanations below.

The items that appear in Adobe Reader vary depending on how it is used. If the Table of Contents or tools do not appear, refer to Adobe Reader Help.

Certain items are indicated in this guide by the conventions described below.

Convention Description

[Bold] Indicates keys and buttons.

"Regular" Indicates a message or setting.

xix

> About the Operation Guide (this Guide)

Conventions used in procedures for operating the machine

In this Operation Guide, continuous operation of the keys on the touch panel is as follows:

Actual procedure Procedure indicated in this guide

Select the [System Menu/Counter] key.



Select [ ].



Select [Common Settings].



Select [Sound].

[System Menu/Counter] key > [Common Settings] > [Sound]

> Menu Map

Menu Map

This is a list of menus displayed on the touch panel. Depending on the settings, some menus may not be displayed. Some menu names may differ from their reference titles.

Paper Selection (page 6-11)

Zoom (page 6-20

Density (page 6-15

Duplex (page 6-24

Combine (page 6-22

Quiet Mode (page 6-27

Functions Collate/Offset (page 6-13)

)

ID Card Copy (page 6-10

Original Size (page 6-10

Original Orientation (page 6-12

Mixed Size Originals (page 6-13

Paper Output (page 6-14

Staple (page 6-14

Original Image (page 6-16

EcoPrint (page 6-17

Sharpness (page 6-18

Contrast (page 6-18

)

Background Density Adj. (page 6-19

Prevent Bleed-through (page 6-19

Skip Blank Page (page 6-28

Continuous Scan (page 6-26

Job Finish Notice (page 6-26

File Name Entry (page 6-27

Priority Override (page 6-27

)

xxi

)

> Menu Map

Send

One Touch Key (page 5-22)

Address Book (page 5-20

Ext Address Book (Refer to Command Center RX User Guide.)

E-mail (page 5-22

Folder (page 5-23

FAX Server (page 5-34

FAX (Refer to FAX Operation Guide.)

WSD Scan (page 5-31

Functions Color Selection (page 6-17)

)

Quiet Mode (page 6-27

File Format (page 6-31

Original Size (page 6-10

Original Orientation (page 6-12

Mixed Size Originals (page 6-13

Duplex (page 6-29

Sending Size (page 6-30

File Separation (page 6-35

)

Scan Resolution (page 6-35

Density (page 6-15

Original Image (page 6-16

Sharpness (page 6-18

Contrast (page 6-18

Background Density Adj. (page 6-19

Prevent Bleed-through (page 6-19

Skip Blank Page (page 6-28

FAX TX Resolution (Refer to FAX Operation Guide.)

Zoom (page 6-20)

Continuous Scan (page 6-26

File Name Entry (page 6-27

E-mail Subject/Body (page 6-35

Long Original (page 6-36

Job Finish Notice (page 6-26

FTP Encrypted TX (page 6-36

)

xxii

> Menu Map

Custom Box

Functions FAX Delayed Transmission (Refer to FAX Operation Guide.)

FAX Direct Transmission (Refer to FAX Operation Guide.)

FAX Polling RX (Refer to FAX Operation Guide.)

FAX TX Report (Refer to FAX Operation Guide.)

Custom Box Menu Store File Duplex (page 6-29)

Scan Resolution (page 6-35

Density (page 6-15

)

File Name Entry (page 6-27

Color Selection (page 6-17

Quiet Mode (page 6-27

)

Functions Original Size (page 6-10)

Original Orientation (page 6-12

Mixed Size Originals (page 6-13

Storing Size (page 6-37

Original Image (page 6-16

Sharpness (page 6-18

Contrast (page 6-18

)

Background Density Adj. (page 6-19

Prevent Bleed-through (page 6-19

Skip Blank Page (page 6-28

Zoom (page 6-20

)

Continuous Scan (page 6-26

Job Finish Notice (page 6-26

Print Paper Selection (page 6-11)

Collate/Offset (page 6-13

Duplex (page 6-24

)

Delete after Print (page 6-36

Quiet Mode (page 6-27

)

xxiii

)

> Menu Map

Custom Box Menu Print Functions Paper Output (page 6-14)

Staple (page 6-14

Priority Override (page 6-27

File Name Entry (page 6-27

Job Finish Notice (page 6-26

EcoPrint (page 6-17

Send One Touch Key (page 5-22)

Address Book (page 5-20

Ext Address Book (Refer to Command Center RX User Guide.)

E-mail (page 5-22

Folder (page 5-23

FAX Server (Refer to FAX Operation Guide.)

FAX (Refer to FAX Operation Guide.)

Functions File Format (page 6-31)

)

File Separation (page 6-35

Resolution (page 6-35

FAX TX Resolution (Refer to FAX Operation Guide.)

)

File Name Entry (page 6-27

E-mail Subject/Body (page 6-35

Job Finish Notice (page 6-26

FTP Encrypted TX (page 6-36

FAX Delayed Transmission (Refer to FAX Operation Guide.)

FAX TX Report (Refer to FAX Operation Guide.)

Delete after Transmitted (page 6-36

Job Box Private Print/Stored Job (page 4-13)

Quick Copy/Proof and Hold (page 4-17

)

xxiv

> Menu Map

USB Drive

USB Drive Print Paper Selection (page 6-11)

Collate/Offset (page 6-13

Duplex (page 6-24

Quiet Mode (page 6-27

Functions Paper Output (page 6-14)

Menu Store File File Format (page 6-31)

)

Staple (page 6-14

EcoPrint (page 6-17

Job Finish Notice (page 6-26

File Name Entry (page 6-27

Priority Override (page 6-27

Encrypted PDF Password (page 6-37

JPEG/TIFF Print (page 6-38

XPS Fit to Page (page 6-38

Duplex (page 6-29

Scan Resolution (page 6-35

Density (page 6-15

)

File Name Entry (page 6-27

Color Selection (page 6-17

)

xxv

> Menu Map

Polling Box

USB Drive Menu Store File Functions Quiet Mode (page 6-27)

Original Size (page 6-10

Original Orientation (page 6-12

Mixed Size Originals (page 6-13

Storing Size (page 6-37

Original Image (page 6-16

Sharpness (page 6-18

Contrast (page 6-18

Background Density Adj. (page 6-19

Prevent Bleed-through (page 6-19

Skip Blank Page (page 6-28

Zoom (page 6-20

Continuous Scan (page 6-26

Long Original (page 6-36

Job Finish Notice (page 6-26

File Separation (page 6-35

)

Sub Address Box (Refer to FAX Operation Guide.)

Polling Box (Refer to FAX Operation Guide.)

FAX Memory RX Box (Refer to FAX Operation Guide.)

xxvi

> Menu Map

6WDWXV

-RE&DQFHO

Print Job Status (page 7-8)

Send Job Status (page 7-4)

Store Job Status (page 7-5)

Scheduled Job (page 7-6)

Print Job Log (page 7-8)

Send Job Log (page 7-8)

Store Job Log (page 7-8)

FAX Job Log (Refer to FAX Operation Guide.)

Scanner (page 7-11)

Printer (page 7-11)

FAX Memory RX Box (refer to FAX Operation Guide.)

FAX (refer to FAX Operation Guide.)

Toner Status (page 7-13)

Paper Status (page 7-13)

USB Drive (page 7-11)

USB Keyboard (page 7-11)

Bluetooth Keyboard (page 7-11)

Staple (page 7-13)

Network Connection Status (page 7-11)

Option Network Connection Status (page 7-12)

Wi-Fi Direct (page 7-12)

Wireless Network (page 7-12)

Wi-Fi (page 7-12)

SSD (page 7-12)

Hard Disk (page 7-12)

xxvii

> Menu Map

6\VWHP

0HQX

Quick Setup Wizard FAX Setup (page 2-40)

Paper Setup (page 2-40

Energy Saver Setup (page 2-40

Network Setup (page 2-41

)

Language (page 8-5)

Report Report Print Status Page (page 8-5)

Font List (page 8-6

)

Network Status (page 8-6

Service Status (page 8-6

Accounting Report (page 8-6

Sub Address Box List (Refer to FAX Operation Guide.)

FAX List (Index) (Refer to FAX Operation Guide.)

FAX List (No.) (Refer to FAX Operation Guide.)

Outgoing FAX Report (Refer to FAX Operation Guide.)

Incoming FAX Report (Refer to FAX Operation Guide.)

Optional Network Status (page 8-6

Data Sanitization Report (page 8-6

)

Admin Report Settings

Result Report Setting

Sending Log History Send Log History (page 8-7)

Counter Printed Pages (page 2-55)

Scanned Pages (page 2-55

User Property (page 9-9)

Outgoing FAX Report (Refer to FAX Operation Guide.)

Incoming FAX Report (Refer to FAX Operation Guide.)

Send Result Report (page 8-7)

RX Result Report (Refer to FAX Operation Guide.)

Job Finish Notice Setting (page 8-7

Auto Sending (page 8-7

Destination (page 8-7

Job Log Subject (page 8-7

)

SSFC Log Subject (page 8-7

Personal Information (page 8-7

)

xxviii

> Menu Map

Cassette/MP Tray Settings

Common Settings Default Screen (page 8-10)

Cassette 1 (page 8-8)

Cassette 2 (page 8-8

Cassette 3 (page 8-8

Cassette 4 (page 8-8

Cassette 5 (page 8-8

Multi Purpose Tray (page 8-9

Sound Buzzer (page 8-10)

Original Settings Custom Original Size (page 8-11)

Paper Settings Custom Paper Size (page 8-12)

)

FAX Speaker Volume (Refer to FAX Operation Guide.)

FAX Monitor Volume (Refer to FAX Operation Guide.)

Auto Detect Original Size (DP) (page 8-11

Default Original Size (page 8-11

Default Original Size (Platen) (page 8-11

Media Type Settings (page 8-14

)

Default Paper Source (page 8-13

Paper Selection (page 8-13

Media for Auto (B & W) (page 8-13

Special Paper Action (page 8-13

Show Paper Setup Message (page 8-13

Function Defaults File Format (page 8-15)

Original Orientation (Copy) (page 8-15

Original Orientation (Send/Store) (page 8-15

Collate/Offset (page 8-15

File Separation (page 8-15

Scan Resolution (page 8-15

Color Selection (page 8-15

Original Image (Copy) (page 8-15

Original Image (Send/Store) (page 8-15

Background Density Adj. (Copy) (page 8-15

Background Density Adj. (Send/Store) (page 8-15

)

EcoPrint (page 8-15

Prevent Bleed-through (Copy) (page 8-15

Prevent Bleed-through (Send/Store) (page 8-16

Skip Blank Page (Copy) (page 8-16

Skip Blank Page (Send/Store) (page 8-16

)

xxix

)

> Menu Map

Common Settings Function Defaults FAX TX Resolution (Refer to FAX Operation Guide.)

Zoom (page 8-16

Continuous Scan (Copy) (page 8-16

Continuous Scan (FAX) (Refer to FAX Operation Guide.)

Continuous Scan (Send/Store) (page 8-16)

File Name Entry (page 8-16

E-mail Subject/Body (page 8-16

FTP Encrypted TX (page 8-16

JPEG/TIFF Print (page 8-16

XPS Fit to Page (page 8-16

Detail Settings Image Quality (page 8-17)

)

PDF/A (page 8-17

High Comp. PDF Image (page 8-17

OCR Text Recognition (page 8-17

Primary OCR Language (page 8-17

OCR Output Format (page 8-17

Detect Items to Skip (Copy) (page 8-17

)

Detect Items to Skip (Send/Store) (page 8-17

Preset Limit (page 8-17

Error Handling Duplexing Error (page 8-18)

Measurement (page 8-18

Low Toner Alert (page 8-19

Keyboard Layout (page 8-19

Optional Keyboard Type (page 8-19

Offset Documents by Job (page 8-19

Offset One Page Documents (page 8-19

Display Status/Log (page 8-20

)

Finishing Error (page 8-18

No Staple Error (page 8-18

Paper Jam before Staple (page 8-18

Paper Mismatch Error (page 8-18

Wrong Size Paper Loaded (page 8-18

Multi Originals Fed (page 8-18

)

Remote Printing (page 8-20

Direct Printing from Web (page 8-20

Function Key Assignment (page 8-20

Show Power Off Message (page 8-21

Message Banner Print (page 8-21

)

xxx

> Menu Map

Home Customize Desktop (page 2-19)

Customize Taskbar (page 2-19

Wallpaper (page 2-19

Copy Auto Paper Selection (page 8-21)

Auto % Priority (page 8-21

Reserve Next Priority (page 8-21

Send Dest. Check before Send (page 8-22)

Entry Check for New Dest. (page 8-22

Send and Forward (page 8-22

Color TIFF Compression (page 8-22

Default Screen (page 8-22

New Destination Entry (page 8-22

Recall Destination (page 8-22

Broadcast (page 8-22

OCR Text Recognition Action (page 8-22

Document Box Custom Box (page 5-39)

Sub Address Box (Refer to FAX Operation Guide.)

)

Job Box Quick Copy Job Retention (page 8-23)

Polling Box (Refer to FAX Operation Guide.)

FAX Memory RX Box (Refer to FAX Operation Guide.)

FAX (Refer to FAX Operation Guide.)

Application (page 5-11)

Internet Proxy (page 8-24)

Address Book/One Touch

Address Book (page 3-30)

One Touch Key (page 3-35

Address Book Defaults

Edit Restriction (page 8-25

Print List (Refer to FAX Operation Guide.)

Deletion of Job Retention (page 8-23

Storage Media (page 8-23

)

Sort (page 8-24)

Address Book (page 8-24

)

xxxi

> Menu Map

User Login/Job Accounting

User Login Settings User Login (page 9-3)

Local User List (page 9-6

ID Card Settings Keyboard Login (page 9-30)

PIN Login (page 9-31

Simple Login Settings

Local User Authorization (page 9-18

Authentication Security

Group Authorization Set.

Guest Authorization Set.

Obtain NW User Property (page 9-25

Job Accounting Settings

Job Accounting (page 9-34)

Job Accounting Access (page 9-35

)

Additional Authentication (page 9-30

)

Simple Login (page 9-27)

Simple Login Setup (page 9-28

)

User Account Lockout Settings (page 9-4)

Password Policy Settings (page 9-5

Group Authorization (page 9-19)

Group List (page 9-20

Guest Authorization (page 9-22)

Guest Property (page 9-23

)

Unknown User Settings

Print Accounting Report (page 9-46

Total Job Accounting (page 9-45

Each Job Accounting (page 9-45

Accounting List (page 9-36

Default Setting Apply Limit (page 9-44)

Unknown ID Job (page 9-48)

User Property (page 9-49

)

Copy/Printer Count (page 9-44

Default Counter Limit (page 9-44

)

xxxii

> Menu Map

Printer Emulation (page 8-25)

EcoPrint (page 8-25

Override A4/Letter (page 8-26

Duplex (page 8-26

Paper Output (page 8-26

Copies (page 8-26

Orientation (page 8-26

Wide A4 (page 8-26

Form Feed TimeOut (page 8-26

LF Action (page 8-26

CR Action (page 8-26

Job Name (page 8-26

User Name (page 8-26

MP Tray Priority (page 8-26

Paper Feed Mode (page 8-27

Auto cassette Change (page 8-27

Resolution (page 8-27

)

KIR (page 8-27

Printing Job Terminator (page 8-27

System/Network Network Host Name (page 8-28)

)

Wi-Fi Direct Settings Wi-Fi Direct (page 8-28)

Wi-Fi Settings Wi-Fi (page 8-28)

Wired Network Settings

Bonjour Protocol Setting (page 8-32)

Device Name (page 8-28

IP Address (page 8-28

Auto Disconnect (page 8-28

Setup (page 8-29

TCP/IP Settings (page 8-30

Restart Network (page 8-31

TCP/IP Settings (page 8-31)

LAN Interface (page 8-31

Available Network (Wi-Fi Direct) (page 8-32

Available Network (Wi-Fi) (page 8-32

)

xxxiii

Available Network (Wired Network) (page 8-32

)

> Menu Map

System/Network Network IP Filter (IPv4) (page 8-32)

IP Filter (IPv6) (page 8-32

IPSec (page 8-32

Protocol Settings (page 8-32

Security Settings SSL (page 8-39)

Ping (page 8-39

Restart Network (page 8-40

Proxy (page 8-40

Optional Network Setup (page 8-40)

Basic (page 8-41

Primary Network (Client) (page 8-42

)

IPP Security (page 8-39

HTTP Security (page 8-39

SMTP Security (page 8-39

POP3 Security (User 1) (page 8-39

POP3 Security (User 2) (page 8-39

POP3 Security (User 3) (page 8-39

)

Interface Block Setting

Bluetooth Settings (page 8-43

Security Level (page 8-43

Restart (page 8-44

RAM Disk Setting (page 8-44

Optional Memory (page 8-44

Data Security (page 8-45

OCR Dictionary Installation (page 8-46

Optional Function (page 8-47

Remote Services Settings (page 8-47

FAX Server Settings (page 8-47

Remote Operation (page 8-48

USB Host (page 8-43)

USB Device (page 8-43

USB Storage (page 8-43

Optional Interface (page 8-43

)

xxxiv

> Menu Map

Date/Timer/Energy Saver

Date/Time (page 8-49)

Date Format (page 8-49

Time Zone (page 8-49

Auto Panel Reset (page 8-49

Panel Reset Timer (page 8-49

Low Power Timer (page 8-49

Sleep Level (models except for Europe) (page 8-49

Sleep Rules (models for Europe) (page 8-50

Sleep Timer (page 8-50

Energy Saver Recovery Level (page 8-50

Weekly Timer Settings (page 8-50

Power Off Rule (models for Europe) (page 8-51

Power Off Timer (models for Europe) (page 8-51

Auto Error Clear (page 8-51

Error Clear Timer (page 8-51

Unusable Time (Refer to FAX Operation Guide.)

)

Adjustment/ Maintenance

Ping Timeout (page 8-51

Quiet Mode Settings Quiet Mode (page 8-52)

Density Adjustment Copy (page 8-52)

Sharpness Adjustment

Contrast Copy (page 8-52)

Background Density Adj.

Toner Save Level (EcoPrint)

Print Density (page 8-52

Auto Color Correction (page 8-53

Correcting Black Line (page 8-53

)

Specify for Each Job (page 8-52

Send/Box (page 8-52

Copy (page 8-52)

Send/Box (page 8-52

Copy (Auto) (page 8-52)

Send/Box (Auto) (page 8-52

Copy (page 8-52)

Printer (page 8-52

)

Display Brightness (page 8-53

Drum Refresh 1 (page 8-53

Drum Refresh 2 (page 8-53

Auto Drum Refresh (page 8-53

Service Setting (page 8-53

)

xxxv

1 Legal and Safety

Information

Please read this information before using your machine. This chapter provides information on the following topics.

Notice ................................................................................................................................................................. 1-2

Safety Conventions in This Guide ............................................................................................................ 1-2

Environment ............................................................................................................................................. 1-3

Precautions for Use ................................................................................................................................. 1-4

Laser Safety (Europe) .............................................................................................................................. 1-5

SAFETY OF LASER BEAM (USA) .......................................................................................................... 1-6

Safety Instructions Regarding the Disconnection of Power ..................................................................... 1-7

Compliance and Conformity .................................................................................................................... 1-7

Other precautions (for users in California, the United States) ................................................................. 1-7

Warranty (the United States and Canada) ............................................................................................... 1-8

Legal Restriction on Copying/Scanning ................................................................................................... 1-9

EN ISO 7779 ............................................................................................................................................ 1-9

EK1-ITB 2000 .......................................................................................................................................... 1-9

Wireless Connection (Mexico only) ......................................................................................................... 1-9

Security Precautions when Using Wireless LAN (If equipped) ................................................................ 1-9

Limited Use of This Product (If equipped) .............................................................................................. 1-10

Legal Information .................................................................................................................................... 1-11

Energy Saving Control Function ............................................................................................................ 1-17

Automatic 2-Sided Print Function .......................................................................................................... 1-17

Resource Saving - Paper ....................................................................................................................... 1-17

Environmental benefits of "Power Management" ................................................................................... 1-17

Energy Star (ENERGY STAR®) Program .............................................................................................. 1-18

1-1

Legal and Safety Information > Notice

NOTE

Notice

Safety Conventions in This Guide

The sections of this guide and parts of the machine marked with symbols are safety warnings meant to protect the user, other individuals and surrounding objects, and ensure correct and safe usage of the machine. The symbols and their meanings are indicated below.

WARNING: Indicates that serious injury or even death may result from insufficient attention to or incorrect compliance with the related points.

CAUTION: Indicates that personal injury or mechanical damage may result from insufficient attention to or incorrect compliance with the related points.

Symbols

The  symbol indicates that the related section includes safety warnings. Specific points of attention are indicated inside the symbol.

... [General warning]

... [Warning of high temperature]

The symbol indicates that the related section includes information on prohibited actions. Specifics of the prohibited action are indicated inside the symbol.

... [Warning of prohibited action]

... [Disassembly prohibited]

The  symbol indicates that the related section includes information on actions which must be performed. Specifics of the required action are indicated inside the symbol.

... [Alert of required action]

... [Remove the power plug from the outlet]

... [Always connect the machine to an outlet with a ground connection]

Please contact your service representative to order a replacement if the safety warnings in this Operation Guide are illegible or if the guide itself is missing (fee required).

An original which resembles a bank note closely may not be copied properly in some rare cases because this machine is equipped with a counterfeiting prevention function.

1-2

Legal and Safety Information > Notice

Environment

The service environmental conditions are as follows:

Temperature 50 to 90.5 °F (10 to 32.5 °C)

Humidity 15 to 80%

Avoid the following locations when selecting a site for the machine.

• Avoid locations near a window or with exposure to direct sunlight.

• Avoid locations with vibrations.

• Avoid locations with drastic temperature fluctuations.

• Avoid locations with direct exposure to hot or cold air.

• Avoid poorly ventilated locations.

If the floor is delicate against casters, when this machine is moved after installation, the floor material may be damaged.

During copying, some ozone is released, but the amount does not cause any ill effect to one's health. If, however, the machine is used over a long period of time in a poorly ventilated room or when making an extremely large number of copies, the smell may become unpleasant. To maintain the appropriate environment for copy work, it is suggested that the room be properly ventilated.

1-3

Legal and Safety Information > Notice

Precautions for Use

Cautions when handling consumables

CAUTION

Do not attempt to incinerate parts which contain toner. Dangerous sparks may cause burns.

Keep parts which contain toner out of the reach of children.

If toner happens to spill from parts which contain toner, avoid inhalation and ingestion, as well as contact with your eyes and skin.

• If you do happen to inhale toner, move to a place with fresh air and gargle thoroughly with a large amount of water. If coughing develops, contact a physician.

• If you do happen to ingest toner, rinse your mouth with water and drink 1 or 2 cups of water to dilute the contents of your stomach. If necessary, contact a physician.

• If you do happen to get toner in your eyes, flush them thoroughly with water. If there is any remaining tenderness, contact a physician.

• If toner does happen to get on your skin, wash with soap and water.

Do not attempt to force open or destroy parts which contain toner.

Other precautions

Return the exhausted toner container and waste toner box to your dealer or service representative. The collected toner container and waste toner box will be recycled or disposed in accordance with the relevant regulations.

Store the machine while avoiding exposure to direct sunlight.

Store the machine in a place where the temperature stays below 40 °C while avoiding sharp changes of temperature and humidity.

If the machine will not be used for an extended period of time, remove the paper from the cassette and the Multi Purpose (MP) Tray, return it to its original package and reseal it.

1-4

Legal and Safety Information > Notice

Laser Safety (Europe)

Laser radiation could be hazardous to the human body. For this reason, laser radiation emitted inside this machine is hermetically sealed within the protective housing and external cover. In the normal operation of the product by user, no radiation can leak from the machine.

This machine is classified as Class 1 laser product under IEC/EN 60825-1:2014.

Regarding CLASS 1 laser products, information is provided on the rating label.

1-5

Legal and Safety Information > Notice

ECOSYS M3860idn / ECOSYS M3860idnf

SAFETY OF LASER BEAM (USA)

1. Safety of laser beam

This machine has been certified by the manufacturer to Class 1 level under the radiation performance standards established by the U.S.DHHS (Department of Health and Human Services) in 1968. This indicates that the product is safe to use during normal operation and maintenance. The laser optical system, enclosed in a protective housing and sealed within the external covers, never permits the laser beam to escape.

2. The CDRH Act

A laser-product-related act was implemented on Aug. 2, 1976, by the Center for Devices and Radiological Health (CDRH) of the U.S. Food and Drug Administration (FDA). This act prohibits the sale of laser products in the U.S. without certification, and applies to laser products manufactured after Aug. 1, 1976. The label shown below indicates compliance with the CDRH regulations and must be attached to laser products marketed in the United States. On this machine, the label is on the rear.

3. Maintenance

For safety of the service personnel, follow the maintenance instructions in the other section of this manual.

4. Safety switch

The power to the laser unit is cut off when the front cover is opened.

1-6

Legal and Safety Information > Notice

Safety Instructions Regarding the Disconnection of Power

Caution: The power plug is the main isolation device! Other switches on the equipment are only functional switches and are not suitable for isolating the equipment from the power source.

Attention: Le débranchement de la fiche secteur est le seul moyen de mettre l'appareil hors tension. Les interrupteurs sur l'appareil ne sont que des interrupteurs de fonctionnement: ils ne mettent pas l'appareil hors tension.

Compliance and Conformity

Hereby, KYOCERA Document Solutions Inc. declares that the radio equipment type ECOSYS M3860idn/ ECOSYS M3860idnf are in compliance with Directive 2014/53/EU.

The full text of the EU declaration of conformity is available at the following internet address: https://www.kyoceradocumentsolutions.eu/index/service/dlc.html

Module name Software Ver. Frequency band in

which the radio

equipment operates:

IB-51 (Option) 2.2.6 2.4GHz 100mW

IB-36 (Option) 2014.12 2.4GHz 100mW

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

• The use of a non-shielded interface cable with the referenced device is prohibited.

CAUTION — The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Maximum radio-frequency power transmitted in the

frequency band in which the radio equipment

operates:

This device complies with Part 15 of FCC Rules.

Operation is subject to the following two conditions; (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other transmitter.

* The above statements are valid only in the United States of America and Canada.

NOTE — Use shielded interface cables.

Other precautions (for users in California, the United States)

Perchlorate Material - special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate.

1-7

Legal and Safety Information > Notice

ECOSYS M3860idn / M3860idnf

MULTIFUNCTIONAL PRODUCT LIMITED WARRANTY

KYOCERA Document Solutions America, Inc. and KYOCERA Document Solutions Canada, Ltd. (both referred to as "KYOCERA") warrant the Customer's new Multifunctional Product (referred to as "MFP"), and the new accessories installed with the initial installation of the MFP, against any defects in material and workmanship for a period of one year, or 500,000 copies/prints from date of installation, whichever first occurs. In the event the MFP or an accessory is found to be defective within the warranty period, KYOCERA's only obligation and the Customer's exclusive remedy shall be replacement of any defective parts. KYOCERA shall have no obligation to furnish labor.

This warranty is valid only for the original retail purchaser (referred to as the "Customer") of a new KYOCERA MFP in the United States of America or Canada, based upon the country of purchase.

In order to obtain performance of this warranty, the Customer must immediately notify the Authorized KYOCERA Dealer from whom the product was purchased. If the KYOCERA Dealer is not able to provide service, write to KYOCERA at the address below for the name and address of the Authorized KYOCERA Dealer in your area, or check KYOCERA's website at http://www.kyoceradocumentsolutions.com/us

for KYOCERA Document Solutions America, Inc. or

http://www.kyoceradocumentsolutions.ca

for KYOCERA Document Solutions Canada, Ltd.

This warranty does not cover MFPs or accessories which: (a) have become damaged due to operator negligence, misuse, accidents, improper storage or unusual physical or electrical stress, (b) have used parts or supplies which are not genuine KYOCERA brand parts or supplies, (c) have been installed or serviced by a technician not employed by KYOCERA or an Authorized KYOCERA Dealer, or (d) have had the serial number modified, altered, or removed.

This warranty gives the Customer specific legal rights. The Customer may also have other rights, which vary from state to state, or province to province. Neither the seller, nor any other person, is authorized to extend the time period or expand this warranty on behalf of KYOCERA.

THIS WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES AND CONDITIONS, EXPRESS OR IMPLIED, AND KYOCERA SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THIS WARRANTY SHALL NOT EXTEND TO, AND KYOCERA SHALL NOT BE LIABLE FOR, ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES WHICH MAY ARISE OUT OF THE USE OF, OR INABILITY TO USE, THE MFP.

Warranty (the United States and Canada)

KYOCERA Document Solutions America, Inc.

225 Sand Road, P.O. Box 40008 Fairfield, New Jersey 07004-0008, USA

KYOCERA Document Solutions Canada, Ltd.

6120 Kestrel Rd., Mississauga, ON L5T 1S8, Canada

1-8

Legal and Safety Information > Notice

Legal Restriction on Copying/Scanning

It may be prohibited to copy/scan copyrighted material without permission of the copyright owner.

Copying/Scanning the following items is prohibited and may be penalized by low. It may not be limited to these items. Do not knowingly copy/scan the items that are not to be copied/scanned.

• Paper money

• Bank note

• Securities

•Stamp

• Passport

• Certificate

Local laws and regulations may prohibit or restrict copying/scanning of other items not mentioned above.

EN ISO 7779

Maschinenlärminformations-Verordnung 3. GPSGV, 06.01.2004: Der höchste Schalldruckpegel beträgt 70 dB (A) oder weniger gemäß EN ISO 7779.

EK1-ITB 2000

Das Gerät ist nicht für die Benutzung im unmittelbaren Gesichtsfeld am Bildschirmarbeitsplatz vorgesehen. Um störende Reflexionen am Bildschirmarbeitsplatz zu vermeiden, darf dieses Produkt nicht im unmittelbaren Gesichtsfeld platziert werden.

Wireless Connection (Mexico only)

The operation of this equipment is subject to the following two conditions:

(1) it is possible that this equipment or device may not cause harmful interference, and (2) this equipment or device must accept any interference, including interference that may cause undesired operation.

La operación de este equipo está sujeta a las siguientes dos condiciones:

(1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operación no deseada.

Security Precautions when Using Wireless LAN (If equipped)

Wireless LAN allows information to be exchanged between wireless access points instead of using a network cable, which offers the advantage that a LAN connection can be established freely within an area in which radio waves can be transmitted.

On the other hand, the following problems may occur if security settings are not configured, because radio waves can pass through obstacles (including walls) and reach everywhere within a certain area.

Secretly Viewing Communication Contents

A third person with malicious objectives may intentionally monitor radio waves and gain unauthorized access to the following communication contents.

• Personal information including ID, passwords, and credit card numbers

• Contents of email messages

1-9

Legal and Safety Information > Notice

Illegal Intrusion

A third party with malicious intent may gain unauthorized access to personal or company networks and conduct the following illegal actions.

• Extracting personal and confidential information (information leak)

• Entering into communication while impersonating a specific person and distributing unauthorized information (spoofing)

• Modifying and retransmitting intercepted communications (falsification)

• Transmitting computer viruses and destroying data and systems (destruction)

Wireless LAN cards and wireless access points contain built-in security mechanisms to address these problems and to reduce the possibility of these problems occurring by configuring the security settings of wireless LAN products when the product is used.

We recommend that customers take responsibility and use their judgment when configuring the security settings and that they ensure that they fully understand the problems that can occur when the product is used without configuring the security settings.

Limited Use of This Product (If equipped)

• Radio waves transmitted from this product may affect medical equipment. When using this product in a medical institution or in the vicinity of medical instruments, either use this product according to the instructions and precautions provided by the administrator of the institution or those provided on the medical instruments.

• Radio waves transmitted from this product may affect automatic control equipment including automatic doors and fire alarms. When using this product in the vicinity of the automatic control equipment, use this product according to the instructions and precautions provided on the automatic control equipment.

• If this product is used in devices that are directly related to service including airplanes, trains, ships, and automobiles or this product is used in applications requiring high reliability and safety to function and in devices requiring accuracy including those used in disaster prevention and crime prevention and those used for various safety purposes, please use this product after considering the safety design of the entire system including adoption of a failsafe design and redundancy design for reliability and safety maintenance of the entire system. This product is not intended for use in applications requiring high reliability and safety including aerospace instruments, trunk communication equipment, nuclear power control equipment, and medical equipment; hence, the decision as to whether to use this product in these applications needs to be fully considered and determined.

Sólo México (Mexico only)

Este equipo utiliza el módulo de interfaz de red inalámbrica modelo LBWA1ZZ1CA para conectarse a las redes Inalámbricas.

1-10

Legal and Safety Information > Notice

Legal Information

Copying or other reproduction of all or part of this guide without the prior written consent of KYOCERA Document Solutions Inc. is prohibited.

Regarding Trade Names

• PRESCRIBE and ECOSYS are registered trademark of Kyocera Corporation.

• KPDL is a trademark of Kyocera Corporation.

• Microsoft, Windows, Windows Server, Internet Explorer, Excel and PowerPoint are registered trademarks or trademarks of Microsoft Corporation in the U.S.A. and/or other countries.

• PCL is a trademark of Hewlett-Packard Company.

• Adobe Acrobat, Adobe Reader and PostScript are trademarks of Adobe Systems, Incorporated.

• Ethernet is a registered trademark of Xerox Corporation.

• IBM and IBM PC/AT are trademarks of International Business Machines Corporation.

• AppleTalk, Bonjour, Macintosh, and Mac OS are trademarks of Apple Inc., registered in the U.S. and other countries.

• All European language fonts installed in this machine are used under licensing agreement with Monotype Imaging Inc.

• Helvetica, Palatino and Times are registered trademarks of Linotype GmbH.

• ITC Avant Garde Gothic, ITC Bookman, ITC ZapfChancery and ITC ZapfDingbats are registered trademarks of International Typeface Corporation.

• ThinPrint is a trademark of Cortado AG in Germany and other countries.

• UFST™ MicroType® fonts by Monotype Imaging Inc. are installed in this machine.

• This machine contains the software having modules developed by Independent JPEG Group.

• iPad, iPhone and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries.

• AirPrint and the AirPrint logo are trademarks of Apple Inc.

• iOS is a trademark or registered trademark of Cisco in the U.S. and other countries and is used under license by Apple Inc.

• Google and Google Cloud Print™ are trademarks and/or registered trademarks of Google Inc.

• Mopria™ is registered trademarks of Mopria™ Alliance.

• Wi-Fi and Wi-Fi Direct are trademarks and/or registered trademarks of Wi-Fi Alliance.

• Powered by ABBYY FineReader ABBYY and FineReader are trademarks of ABBYY Software Ltd.

All other brands and product names are registered trademarks or trademarks of their respective companies. The designations ™ and ® will not be used in this Operation Guide.

1-11

Legal and Safety Information > Notice

GPL/LGPL

This product contains GPL (http://www.gnu.org/licenses/gpl.html) and/or LGPL (http://www.gnu.org/licenses/lgpl.html) software as part of its firmware. You can get the source code, and you are permitted to copy, redistribute and modify it under the terms of GPL/LGPL. For further information including availability of the source code, visit http://www.kyoceradocumentsolutions.com/gpl/.

OpenSSL License

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

3. All advertising materials mentioning features or use of this software must display the following acknowledgment: "This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.openssl.org/)"

4. The names "OpenSSL Toolkit" and "OpenSSL Project" must not be used to endorse or promote products derived from this software without prior written permission. For written permission, please contact openssl-core@openssl.org.

5. Products derived from this software may not be called "OpenSSL" nor may "OpenSSL" appear in their names without prior written permission of the OpenSSL Project.

6. Redistributions of any form whatsoever must retain the following acknowledgment: "This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit (http://www.openssl.org/)"

THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT "AS IS" AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

Original SSLeay License

This package is an SSL implementation written by Eric Young (eay@cryptsoft.com). The implementation was written so as to conform with Netscapes SSL.

This library is free for commercial and non-commercial use as long as the following conditions are adhered to. The following conditions apply to all code found in this distribution, be it the RC4, RSA, lhash, DES, etc., code; not just the SSL code. The SSL documentation included with this distribution is covered by the same copyright terms except that the holder is Tim Hudson (tjh@cryptsoft.com).

If this package is used in a product, Eric Young should be given attribution as the author of the parts of the library used.

This can be in the form of a textual message at program startup or in documentation (online or textual) provided with the package.

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1-12

Legal and Safety Information > Notice

1. Redistributions of source code must retain the copyright notice, this list of conditions and the following disclaimer.

3. All advertising materials mentioning features or use of this software must display the following acknowledgement: "This product includes cryptographic software written by Eric Young (eay@cryptsoft.com)" The word 'cryptographic' can be left out if the routines from the library being used are not cryptographic related :-).

4. If you include any Windows specific code (or a derivative thereof) from the apps directory (application code) you must include an acknowledgement: "This product includes software written by Tim Hudson (tjh@cryptsoft.com)"

THIS SOFTWARE IS PROVIDED BY ERIC YOUNG "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

The licence and distribution terms for any publically available version or derivative of this code cannot be changed. i.e. this code cannot simply be copied and put under another distribution licence [including the GNU Public Licence.]

Monotype Imaging License Agreement

1 Software shall mean the digitally encoded, machine readable, scalable outline data as encoded in a special format as

well as the UFST Software.

2 You agree to accept a non-exclusive license to use the Software to reproduce and display weights, styles and

versions of letters, numerals, characters and symbols (Typefaces) solely for your own customary business or personal purposes at the address stated on the registration card you return to Monotype Imaging. Under the terms of this License Agreement, you have the right to use the Fonts on up to three printers. If you need to have access to the fonts on more than three printers, you need to acquire a multiuser license agreement which can be obtained from Monotype Imaging. Monotype Imaging retains all rights, title and interest to the Software and Typefaces and no rights are granted to you other than a License to use the Software on the terms expressly set forth in this Agreement.

3 To protect proprietary rights of Monotype Imaging, you agree to maintain the Software and other proprietary

information concerning the Typefaces in strict confidence and to establish reasonable procedures regulating access to and use of the Software and Typefaces.

4 You agree not to duplicate or copy the Software or Typefaces, except that you may make one backup copy. You

agree that any such copy shall contain the same proprietary notices as those appearing on the original.

5 This License shall continue until the last use of the Software and Typefaces, unless sooner terminated. This License

may be terminated by Monotype Imaging if you fail to comply with the terms of this License and such failure is not remedied within thirty (30) days after notice from Monotype Imaging. When this License expires or is terminated, you shall either return to Monotype Imaging or destroy all copies of the Software and Typefaces and documentation as requested.

6 You agree that you will not modify, alter, disassemble, decrypt, reverse engineer or decompile the Software.

7 Monotype Imaging warrants that for ninety (90) days after delivery, the Software will perform in accordance with

Monotype Imaging-published specifications, and the diskette will be free from defects in material and workmanship. Monotype Imaging does not warrant that the Software is free from all bugs, errors and omissions.

The parties agree that all other warranties, expressed or implied, including warranties of fitness for a particular purpose and merchantability, are excluded.

8 Your exclusive remedy and the sole liability of Monotype Imaging in connection with the Software and Typefaces is

repair or replacement of defective parts, upon their return to Monotype Imaging.

In no event will Monotype Imaging be liable for lost profits, lost data, or any other incidental or consequential damages, or any damages caused by abuse or misapplication of the Software and Typefaces.

9 Massachusetts U.S.A. law governs this Agreement.

1-13

Legal and Safety Information > Notice

10 You shall not sublicense, sell, lease, or otherwise transfer the Software and/or Typefaces without the prior written

consent of Monotype Imaging.

11 Use, duplication or disclosure by the Government is subject to restrictions as set forth in the Rights in Technical Data

and Computer Software clause at FAR 252-227-7013, subdivision (b)(3)(ii) or subparagraph (c)(1)(ii), as appropriate. Further use, duplication or disclosure is subject to restrictions applicable to restricted rights software as set forth in FAR 52.227-19 (c)(2).

12 You acknowledge that you have read this Agreement, understand it, and agree to be bound by its terms and

conditions. Neither party shall be bound by any statement or representation not contained in this Agreement. No change in this Agreement is effective unless written and signed by properly authorized representatives of each party. By opening this diskette package, you agree to accept the terms and conditions of this Agreement.

Knopflerfish License

This product includes software developed by the Knopflerfish Project. http://www.knopflerfish.org

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

- Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.

- Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

- Neither the name of the KNOPFLERFISH project nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

Apache License (Version 2.0)

Apache License

Version 2.0, January 2004

http://www.apache.org/licenses/

TERMS AND CONDITIONS FOR USE, REPRODUCTION, AND DISTRIBUTION

1. Definitions.

"License" shall mean the terms and conditions for use, reproduction, and distribution as defined by Sections 1 through 9 of this document.

"Licensor" shall mean the copyright owner or entity authorized by the copyright owner that is granting the License.

"Legal Entity" shall mean the union of the acting entity and all other entities that control, are controlled by, or are under common control with that entity. For the purposes of this definition, "control" means (i) the power, direct or indirect, to cause the direction or management of such entity, whether by contract or otherwise, or (ii) ownership of fifty percent (50%) or more of the outstanding shares, or (iii) beneficial ownership of such entity.

"You" (or "Your") shall mean an individual or Legal Entity exercising permissions granted by this License.

"Source" form shall mean the preferred form for making modifications, including but not limited to software source code, documentation source, and configuration files.

1-14

Legal and Safety Information > Notice

"Object" form shall mean any form resulting from mechanical transformation or translation of a Source form, including but not limited to compiled object code, generated documentation, and conversions to other media types.

"Work" shall mean the work of authorship, whether in Source or Object form, made available under the License, as indicated by a copyright notice that is included in or attached to the work (an example is provided in the Appendix below).

"Derivative Works" shall mean any work, whether in Source or Object form, that is based on (or derived from) the Work and for which the editorial revisions, annotations, elaborations, or other modifications represent, as a whole, an original work of authorship. For the purposes of this License, Derivative Works shall not include works that remain separable from, or merely link (or bind by name) to the interfaces of, the Work and Derivative Works thereof.

"Contribution" shall mean any work of authorship, including the original version of the Work and any modifications or additions to that Work or Derivative Works thereof, that is intentionally submitted to Licensor for inclusion in the Work by the copyright owner or by an individual or Legal Entity authorized to submit on behalf of the copyright owner. For the purposes of this definition, "submitted" means any form of electronic, verbal, or written communication sent to the Licensor or its representatives, including but not limited to communication on electronic mailing lists, source code control systems, and issue tracking systems that are managed by, or on behalf of, the Licensor for the purpose of discussing and improving the Work, but excluding communication that is conspicuously marked or otherwise designated in writing by the copyright owner as "Not a Contribution."

"Contributor" shall mean Licensor and any individual or Legal Entity on behalf of whom a Contribution has been received by Licensor and subsequently incorporated within the Work.

2. Grant of Copyright License. Subject to the terms and conditions of this License, each Contributor hereby grants to You a perpetual, worldwide, non-exclusive, no-charge, royalty-free, irrevocable copyright license to reproduce, prepare Derivative Works of, publicly display, publicly perform, sublicense, and distribute the Work and such Derivative Works in Source or Object form.

3. Grant of Patent License. Subject to the terms and conditions of this License, each Contributor hereby grants to You a perpetual, worldwide, non-exclusive, no-charge, royalty-free, irrevocable (except as stated in this section) patent license to make, have made, use, offer to sell, sell, import, and otherwise transfer the Work, where such license applies only to those patent claims licensable by such Contributor that are necessarily infringed by their Contribution(s) alone or by combination of their Contribution(s) with the Work to which such Contribution(s) was submitted. If You institute patent litigation against any entity (including a cross-claim or counterclaim in a lawsuit) alleging that the Work or a Contribution incorporated within the Work constitutes direct or contributory patent infringement, then any patent licenses granted to You under this License for that Work shall terminate as of the date such litigation is filed.

4. Redistribution. You may reproduce and distribute copies of the Work or Derivative Works thereof in any medium, with or without modifications, and in Source or Object form, provided that You meet the following conditions:

(a)You must give any other recipients of the Work or Derivative Works a copy of this License; and

(b)You must cause any modified files to carry prominent notices stating that You changed the files; and

(c)You must retain, in the Source form of any Derivative Works that You distribute, all copyright, patent, trademark,

and attribution notices from the Source form of the Work, excluding those notices that do not pertain to any part of the Derivative Works; and

(d)If the Work includes a "NOTICE" text file as part of its distribution, then any Derivative Works that You distribute

must include a readable copy of the attribution notices contained within such NOTICE file, excluding those notices that do not pertain to any part of the Derivative Works, in at least one of the following places: within a NOTICE text file distributed as part of the Derivative Works; within the Source form or documentation, if provided along with the Derivative Works; or, within a display generated by the Derivative Works, if and wherever such third-party notices normally appear. The contents of the NOTICE file are for informational purposes only and do not modify the License. You may add Your own attribution notices within Derivative Works that You distribute, alongside or as an addendum to the NOTICE text from the Work, provided that such additional attribution notices cannot be construed as modifying the License.

You may add Your own copyright statement to Your modifications and may provide additional or different license terms and conditions for use, reproduction, or distribution of Your modifications, or for any such Derivative Works as a whole, provided Your use, reproduction, in this License.

and distribution of the Work otherwise complies with the conditions stated

1-15

Legal and Safety Information > Notice

5. Submission of Contributions. Unless You explicitly state otherwise, any Contribution intentionally submitted for inclusion in the Work by You to the Licensor shall be under the terms and conditions of this License, without any additional terms or conditions. Notwithstanding the above, nothing herein shall supersede or modify the terms of any separate license agreement you may have executed with Licensor regarding such Contributions.

6. Trademarks. This License does not grant permission to use the trade names, trademarks, service marks, or product names of the Licensor, except as required for reasonable and customary use in describing the origin of the Work and reproducing the content of the NOTICE file.

7. Disclaimer of Warranty. Unless required by applicable law or agreed to in writing, Licensor provides the Work (and each Contributor provides its Contributions) on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied, including, without limitation, any warranties or conditions of TITLE, NONINFRINGEMENT, MERCHANTABILITY, or FITNESS FOR A PARTICULAR PURPOSE. You are solely responsible for determining the appropriateness of using or redistributing the Work and assume any risks associated with Your exercise of permissions under this License.

8. Limitation of Liability. In no event and under no legal theory, whether in tort (including negligence), contract, or otherwise, unless required by applicable law (such as deliberate and grossly negligent acts) or agreed to in writing, shall any Contributor be liable to You for damages, including any direct, indirect, special, incidental, or consequential damages of any character arising as a result of this License or out of the use or inability to use the Work (including but not limited to damages for loss of goodwill, work stoppage, computer failure or malfunction, or any and all other commercial damages or losses), even if such Contributor has been advised of the possibility of such damages.

9. Accepting Warranty or Additional Liability. While redistributing the Work or Derivative Works thereof, You may choose to offer, and charge a fee for, acceptance of support, warranty, indemnity, or other liability obligations and/or rights consistent with this License. However, in accepting such obligations, You may act only on Your own behalf and on Your sole responsibility, not on behalf of any other Contributor, and only if You agree to indemnify, defend, and hold each Contributor harmless for any liability incurred by, or claims asserted against, such Contributor by reason of your accepting any such warranty or additional liability.

END OF TERMS AND CONDITIONS

APPENDIX: How to apply the Apache License to your work.

To apply the Apache License to your work, attach the following boilerplate notice, with the fields enclosed by brackets "[]" replaced with your own identifying information. (Don't include the brackets!) The text should be enclosed in the appropriate comment syntax for the file format. We also recommend that a file or class name and description of purpose be included on the same "printed page" as the copyright notice for easier identification within third-party archives.

Licensed under the Apache License, Version 2.0 (the "License"); you may not use this file except in compliance with the License. You may obtain a copy of the License at

http://www.apache.org/licenses/LICENSE-2.0

Unless required by applicable law or agreed to in writing, software distributed under the License is distributed on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License for the specific language governing permissions and limitations under the License.

1-16

Legal and Safety Information > Notice

Energy Saving Control Function

The device comes equipped with a Sleep where printer and fax functions remain in a waiting state but power consumption is reduced to a minimum after a certain amount of time elapses since the device was last used.

Sleep

The device automatically enters Sleep when 1 minute has passed since the device was last used. The amount of time of no activity that must pass before Sleep is activated may be lengthened.

Sleep and Auto Sleep (page 2-38)

Automatic 2-Sided Print Function

This device includes 2-sided printing as a standard function. For example, by printing two 1-sided originals onto a single sheet of paper as a 2-sided print, it is possible to lower the amount of paper used.

Duplex (page 6-24)

Printing in duplex mode reduces paper consumption and contributes to the conservation of forest resources. Duplex mode also reduces the amount of paper that must be purchased, and thereby reduces cost. It is recommended that machines capable of duplex printing be set to use duplex mode by default.

Resource Saving - Paper

For the preservation and sustainable use of forest resources, it is recommended that recycled as well as virgin paper

certified under environmental stewardship initiatives or carrying recognised ecolabels, which meet EN 12281:2002 an equivalent quality standard, be used.

This machine also supports printing on 64 g/m further saving of forest resources.

* : EN12281:2002 "Printing and business paper - Requirements for copy paper for dry toner imaging processes"

Your sales or service representative can provide information about recommended paper types.

paper. Using such paper containing less raw materials can lead to

Environmental benefits of "Power Management"

To reduce power consumption when idle, this machine is equipped with a power management function that automatically activates energy-saving mode when the machine is idle for a certain period of time. Although it takes the machine a slight amount of time to return to READY mode when in energy-saving mode, a significant reduction in energy consumption is possible. It is recommended that the machine be used with the activation time for energy-saving mode set to the default setting.

1-17

Legal and Safety Information > Notice

Energy Star (ENERGY STAR®) Program

We participate in the ENERGY STAR® Program.

We provide the products complied with ENERGY STAR

ENERGY STAR products with high energy efficiency in order to help prevent global warming. By purchasing the products

complied with ENERGY STAR product use and cut energy-related costs.

is an energy efficiency program with the goal of developing and promoting the use of

, customers can help reduce emissions of greenhouse gases during

to the market.

1-18

2 Installing and Setting

up the Machine

This chapter provides information for the administrator of this machine, such as part names, cable connection, and software installation.

Part Names ................................................... 2-2

Machine Exterior ................................. 2-2

Connectors/Interior ............................. 2-6

With Optional Equipments Attached . 2-10 Connecting the Machine and Other

Devices ....................................................... 2-12

Connecting Cables ...................................... 2-13

Connecting LAN Cable ..................... 2-13

Connecting USB Cable ..................... 2-14

Connecting the Power Cable ............ 2-14

Power On/Off .............................................. 2-15

Power On .......................................... 2-15

Power Off .......................................... 2-15

Using the Operation Panel .......................... 2-16

Operation Panel Keys ....................... 2-16

Adjusting the Operation

Panel Angle ....................................... 2-17

Touch Panel ................................................ 2-18

Home Screen .................................... 2-18

Display for Device Information .......... 2-22

Functions key .................................... 2-23

Display of Keys That Cannot

Be Set ............................................... 2-24

Enter key and Quick No.

Search key ........................................ 2-25

Help Screen ...................................... 2-26

Logout ............................................... 2-28

Default Settings of the Machine .................. 2-29

Setting Date and Time ...................... 2-29

Network Setup ............................................ 2-30

Configuring the Wired Network ......... 2-30

Configuring the Wireless Network .... 2-32

Setting Wi-Fi Direct ........................... 2-36

Energy Saver function ................................. 2-38

Low Power Mode .............................. 2-38

Sleep and Auto Sleep ....................... 2-38

Power Off Rule

(models for Europe) .......................... 2-39

Quick Setup Wizard .................................... 2-40

Installing Software ....................................... 2-42

Software on DVD (Windows) ............ 2-42

Installing Software in Windows ......... 2-43

Uninstalling the Software .................. 2-49

Installing Software

in Mac Computer .............................. 2-50

Setting TWAIN Driver ........................ 2-52

Setting WIA Driver ............................ 2-54

Checking the Counter ................................. 2-55

Additional Preparations for

the Administrator ......................................... 2-56

Sending Documents to a PC ............ 2-56

Strengthening the Security ............... 2-56

Command Center RX .................................. 2-58

Accessing Command Center RX ...... 2-59

Changing Security Settings .............. 2-60

Changing Device Information ........... 2-62

E-mail Settings .................................. 2-64

Registering Destinations ................... 2-68

Creating a New Custom Box ............ 2-69

Printing a document stored in a Custom

Box .................................................... 2-70

Transferring Data from Our Other

Products ...................................................... 2-72

Migrating the Address Book .............. 2-72

2-1

Installing and Setting up the Machine > Part Names

1 2 3 4

13 14

15 16

Part Names

Machine Exterior

Model without the finisher

1 Document Processor

2 Original Width Guides

3 Original Table

4 Original Eject Table

5 Inner Tray

6 Paper Stopper

7 Front Cover

8 Cassette 1

9 Power Switch

10 Original Stopper

11 USB Memory Slot

12 Front Cover Open Button

13 Slit Glass

14 Original Size Indicator Plates

15 Platen

16 Operation Panel

17 Handles

2-2

Installing and Setting up the Machine > Part Names

18 Anti-theft Lock Slot

19 Rear Cover

2-3

Installing and Setting up the Machine > Part Names

1 2 3 4

15 16

17 18

Model with the finisher

1 Document Processor

2 Original Width Guides

3 Original Table

4 Original Eject Table

5 Inner Finisher

6 Tray Extension

7 Inner Tray

8 Paper Stopper

9 Front Cover

10 Cassette 1

11 Power Switch

12 Original Stopper

13 USB Memory Slot

14 Front Cover Open Button

15 Slit Glass

16 Original Size Indicator Plates

17 Platen

18 Operation Panel

19 Staple Cover

20 Handles

2-4

Installing and Setting up the Machine > Part Names

21 Anti-theft Lock Slot

22 Finisher Rear Cover

23 Rear Cover

2-5

Installing and Setting up the Machine > Part Names

1 2

8 9

Connectors/Interior

Model without the finisher

1 USB Interface Connector

2 Network Interface Connector

3 Option Interface Slot

4 TEL Connector

5 LINE Connector

6 Fuser Cover

7 Paper Width Guides

8 Tray Extension

9 Multi Purpose Tray

10 Paper Length Guide

11 Paper Width Guides

12 Bottom Plate

13 Size Dial

14 Duplex Cover

2-6

Installing and Setting up the Machine > Part Names

1 2

15 Toner Container

16 Toner Container Lock Lever

17 Registration Roller

Model with the finisher

18 Left Cover

19 Waste Toner Box

1 USB Interface Connector

2 Network Interface Connector

3 Option Interface Slot

4 TEL Connector

5 LINE Connector

6 Fuser Cover

2-7

Installing and Setting up the Machine > Part Names

8 9

7 Paper Width Guides

8 Tray Extension

9 Multi Purpose Tray

10 Paper Length Guide

11 Paper Width Guides

12 Bottom Plate

13 Size Dial

14 Duplex Cover

2-8

Installing and Setting up the Machine > Part Names

15 Toner Container

16 Toner Container Lock Lever

17 Registration Roller

18 Left Cover

19 Waste Toner Box

2-9

Installing and Setting up the Machine > Part Names

8 9

With Optional Equipments Attached

Model without the finisher

1 Card Reader

2 Cassette 2

3 Cassette 3

4 Cassette 4

5 Cassette 5

6 Castor kit

7 Manual Stapler

8 Rear Tray

9 Paper Stopper

Optional Equipment (page 11-2)

2-10

Installing and Setting up the Machine > Part Names

7 8

Model with the finisher

1 Card Reader

2 Cassette 2

3 Cassette 3

4 Cassette 4

5 Cassette 5

6 Castor kit

7 Rear Tray

8 Paper Stopper

Optional Equipment (page 11-2)

2-11

Installing and Setting up the Machine > Connecting the Machine and Other Devices

NOTE

IMPORTANT

USB

Ta bl et

Network cable connection

Network

Wi-Fi access point

Wi-Fi connection

Wi-Fi Direct connection

*1 Only for models with the optional Wireless Network Interface Kit (IB-36).

Connecting the Machine and Other Devices

Prepare the cables necessary to suit the environment and purpose of the machine use.

When Connecting the Machine to the PC via USB

When Connecting the Machine to the PC or Tablet by network cable, Wi-Fi, or Wi-Fi direct

If you are using wireless LAN, refer to the following.

Configuring the Wireless Network (page 2-32)

Cables that Can Be Used

Connection Environment Function Necessary Cable

Connect a LAN cable to the machine.

Connect a USB cable to the machine.

Using a cable other than a USB 2.0 compatible cable may cause failure.

Printer/Scanner/Network FAX LAN cable (10BASE-T, 100BASE-TX,

Printer/Scanner (TWAIN/WIA) USB 2.0 compatible cable (Hi-Speed USB

2-12

1000BASE-T)

compliant, max. 5.0 m , shielded)

Installing and Setting up the Machine > Connecting Cables

IMPORTANT

Connecting Cables

Connecting LAN Cable

If the power is on, turn the power switch off.

Power Off (page 2-15)

Connect the cable to the machine.

1 Connect the LAN cable to the network interface connector.

2 Connect the other end of the cable to the hub.

Power on the machine and configure the network.

Network Setup (page 2-30)

2-13

Installing and Setting up the Machine > Connecting Cables

IMPORTANT

Connecting USB Cable

If the power is on, turn the power switch off.

Power Off (page 2-15)

Connect the cable to the machine.

1 Connect the USB cable to the USB interface connector located on the left side of the body.

2 Connect the other end of the cable to the PC.

Power on the machine.

Connecting the Power Cable

Connect the cable to the machine.

Connect one end of the supplied power cable to the machine and the other end to a power outlet.

Only use the power cable that comes with the machine.

2-14

Installing and Setting up the Machine > Power On/Off

IMPORTANT

CAUTION

IMPORTANT

Power On/Off

Power On

Turn the power switch on.

When turning off the power switch, do not turn on the power switch again immediately. Wait more than 5 seconds, and then turn on the power switch.

Power Off

Turn the power switch off.

The confirmation message for power supply off is displayed.

Show Power Off Message (page 8-21)

It takes approximately 3 minutes for power off.

If this machine will be left unused for an extended period (e.g. overnight), turn it off at the main power switch. If the machine will not be used for an even longer period of time (e.g. vacation), remove the power plug from the outlet as a safety precaution.

• If using the products equipped with the fax function, note that turning the machine off at the main power switch disables fax transmission and reception.

• Remove paper from the cassettes and seal it in the paper storage bag to protect it from humidity.

2-15

Installing and Setting up the Machine > Using the Operation Panel

6HOHFWWKHIXQFWLRQ

+RPH

$GPLQ

&RS\

6WDWXV

-RE&DQFHO



/RJRXW

6HQG

-RE%R[

)$;

6XE

$GGUHVV

%R[

86%'ULYH 3ROOLQJ%R[

'HYLFH

,QIRUPDWLRQ

/DQJXDJH 6\VWHP

0HQX

)DYRULWHV

3DSHU

6HWWLQJV

&XVWRP%R[

Lights or blinks when an error occurs and a job is stopped.

Blinks while printing or sending/receiving.

Blinks while the machine is accessing the machine memory, fax memory or USB drive (general purpose item).

Displays the Home screen. Function Key:

These keys enable various functions and applications, including copy and scan, to be registered.

Function Key Assignment (page 8-20)

Displays the Status/Job Cancel screen.

Touch panel. Displays buttons for configuring machine settings.

Displays the System Menu/ Counter screen.

Authenticates user switching, and exits the operation for the current user (i.e. log out).

Puts the machine into Sleep Mode. Recovers from Sleep if in Sleep Mode.

Numeric keys.

Enter numbers and symbols.

Clears entered numbers and characters.

Returns settings to their default states.

Specifies registered information such as address numbers and user IDs by number.

Cancels or pauses the job in progress.

Finalizes numeric key entry, and finalizes details during setting of functions. Operates linked with the on-screen [OK].

Starts copying and scanning operations and processing for setting operations.

Using the Operation Panel

Operation Panel Keys

2-16

Installing and Setting up the Machine > Using the Operation Panel

Adjusting the Operation Panel Angle

The angle of the operation panel can be adjusted.

2-17

Installing and Setting up the Machine > Touch Panel

NOTE

6 5

Copy

Status/

Job Cancel

Logout

SendCustom Box

Job Box USB DrivePolling Box

Device

Information

Language System

Favorites

Sub Address Box

FAX

Status/

Job Cancel

Device

Information

Language System

Favorites

Paper

Settings

122

Touch Panel

Home Screen

This screen is displayed by selecting the [Home] key on the operation panel. Touching an icon will display the corresponding screen.

You can change the icons to display on the Home screen as well as its background.

Editing the Home Screen (page 2-19)

Select the function.

Home

FAX

Copy

Sub Address Box

Job Box

Status/

Job Cancel

Device

Information

Send

USB Drive Polling Box

Device

Information

Language System

Paper

Language System

Paper

Settings

FAX

Sub

Address

Box

Admin

Copy

Job Box USB DrivePolling Box

Custom Box

Logout

SendCustom Box

Favorites

10:10

* The appearance may differ from your actual screen, depending on your configuration and option settings.

No. Item Description

1 Message Displays the message depending on the status.

2 Desktop Displays a maximum of 40 function icons*1 including the functions

registered in favorite. Icons that are not displayed on the first page will appear by changing the page.

3 Screen-switching

keys

Use these buttons to switch between desktop pages.

You can also switch views by touching the screen and moving the finger sideways (i.e. swiping).

4 Taskbar Displays a maximum of 8 task icons.

5 [Logout] Logs out the current user. This is displayed when user login

administration is enabled.

6 Login User Name Displays the logged-in user name. This is displayed when user login

administration is enabled. Selecting "Login User Name" will display the information of the logged-in user.

7 Status Icon (Wi-Fi) The icon is displayed when Wi-Fi is connected. When Wi-Fi is not

8 Status Icon (Error) The icon is displayed during network startup or error.

connected, " " is displayed.

*1 A maximum of 42 icons can be displayed. A maximum of 16 icons can be displayed for installed

applications.

2-18

Installing and Setting up the Machine > Touch Panel

NOTE

Editing the Home Screen

You can change the background of the Home screen as well as which icons are displayed.

Display the screen.

1 [System Menu/Counter] key > [Home]

You can only change the settings by logging in with administrator privileges.

The factory default login user name and login password are set as shown below.

Configure the settings.

The available settings are shown below.

Item Description

Customize Desktop Specify the function icons to display on the desktop.

Select [ ] to display the screen for selecting the function to display. Select the function to display and [OK].

Select an icon and [Previous] or [After] to change the display position of the selected icon on the Desktop.

To delete an icon from desktop, select the desired one and select [ ].

Customize Taskbar Specify the task icons to display on the taskbar.

Wallpaper Configure the wallpaper of the Home screen.

Value: Images 1 to 8

2-19

Installing and Setting up the Machine > Touch Panel

Available Functions to Display on Desktop

Reference

page

Copy

Send

Function Icon Description

Displays the Copy screen. page 5-16

Displays the Send screen. page 5-18

FAX Displays the FAX screen. Refer to the

FAX Operation Guide.

Custom Box

Job Box

USB Drive

Displays the Custom Box screen. page 5-39

Displays the Job Box screen. page 4-12

Displays the USB Drive screen. page 5-50

Sub Address Box Displays the Sub Address Box screen. Refer to the

FAX Operation Guide.

Polling Box Displays the Polling Box screen. Refer to the

FAX Operation Guide.

Send to Me (E-mail)

Displays the Send screen. The E-mail

page 5-27

address of the logged-in user is set as the destination.

Send to Me for Box (E-mail)

*2*3

Displays the Custom Box screen. The E-mail address of the logged-in user is

page 5-48

set as the destination.

FAX Memory RX Box Displays the FAX Memory RX Box

screen.

Refer to the

FAX Operation

Guide.

FAX Server Displays the FAX Server screen. page 8-47

Favorites Calls up the registered favorite. The icon

page 5-6

will change according to the function of the favorite.

Application Name

Displays the selected applications. page 5-11

*1 Selected at the time of shipment from factory. *2 Displayed when the optional hard disk/SSD is installed. *3 Displayed when user login administration is enabled. *4 The icon of the application appears.

2-20

Installing and Setting up the Machine > Touch Panel

Available Functions to Display on Taskbar

Function Icon Description

Status/Job Cancel

Device Information Displays the Device Information screen.

Language Displays the Language setting screen in

Paper Settings Display the paper settings screen. page 8-12

Wi-Fi Direct Configures Wi-Fi Direct settings and

System Menu Displays the System Menu screen. page 8-2

Displays the Status screen. If an error occurs, the icon will show "!". Once the error clears, the display will return to normal.

Check the system and network information.

You can also check information on the options that are used.

System Menu.

displays a list of information about machines that are enabled to use the network.

Reference

page

page 2-22

page 8-5

page 2-36

Favorites Displays the favorite list screen. page 5-6

Outgoing FAX Log Displays the Outgoing FAX Log screen. Refer to the

FAX Operation

Guide.

Incoming FAX Log Displays the Incoming FAX Log screen. Refer to the

FAX Operation

Guide.

2-21

Installing and Setting up the Machine > Touch Panel

Display for Device Information

Shows device information. Allows you to check system and network information, as well as options that are used.

1 Select [Device Information] in the home screen.

2 Check the device information.

Device information

Tab Description

Identification/Network You can check ID information such as the model name, serial

number, host name and location, and the IP address.

Wi-Fi

FAX You can check the local fax number, local fax name, local fax

Software Ver./Capability You can check the software version and performance.

Option You can check information on the options that are used.

You can check ID information such as the model name, serial number, host name and location, and the IP address of the wireless network.

ID and other fax information.

*1 Displayed only when the wireless network function is available on the machine.

2-22

Installing and Setting up the Machine > Touch Panel

Ready to copy.

Copy Copies

Paper Selection

Zoom Density

Duplex Combine

1-sided>>1-sided

A4 100% Normal 0

Off

Functions

10:10

Favorites

Quiet Mode

Off

ID Card Copy

Ready to copy.

Functions

Original Size

10:10

Original Orientation

Top Edge on Top

Collate

Off

ID Card Copy

Collate/Offset

1/4

Add/Edit Shortcut

1 Display functions.

2Select [Functions] to display other functions.

3 Select [ ] or [ ] to scroll up and down.

Functions key

This screen appears when the Functions icon is selected.

2-23

Installing and Setting up the Machine > Touch Panel

NOTE

Ready to copy.

Copy Copies

Paper Selection

Zoom Density

Duplex Combine

1-sided>>1-sided

A4 100% Normal 0

Off

Functions

10:10

Favorites

Quiet Mode

Off

ID Card Copy

Ready to copy.

Copy Copies

Paper Selection

Zoom Density

Duplex Combine

1-sided>>1-sided

A4 100% Normal 0

Off

Functions

10:10

Favorites

Quiet Mode

Off

ID Card Copy

6HOHFWWKHIXQFWLRQ

+RPH

$GPLQ

&RS\

6WDWXV

-RE&DQFHO



/RJRXW

6HQG

-RE%R[

)$;

6XE

$GGUHVV

%R[

86%'ULYH 3ROOLQJ%R[

'HYLFH

,QIRUPDWLRQ

/DQJXDJH 6\VWHP

0HQX

)DYRULWHV

3DSHU

6HWWLQJV

&XVWRP%R[

6HOHFWWKHIXQFWLRQ

+RPH

$GPLQ

&RS\

6WDWXV

-RE&DQFHO



/RJRXW

6HQG

)$; 0HPRU\ 5;%R[

-RE%R[)$;

6XE

$GGUHVV

%R[

86%'ULYH 3ROOLQJ%R[

'HYLFH

,QIRUPDWLRQ

/DQJXDJH 6\VWHP

0HQX

)DYRULWHV

3DSHU

6HWWLQJV

Document Box

Job Box

10:10System Menu/Counter.

< Back

Sub Address Box

Custom Box

Polling Box

1/2

Document Box

Job Box

10:10System Menu/Counter.

< Back

Sub Address Box

FAX Memory RX Box

Polling Box

1/1

Display of Keys That Cannot Be Set

Keys of features that cannot be used due to feature combination restrictions or non-installation of options are in a nonselectable state.

Normal Grayed out

In the following cases, the key is grayed out and cannot be selected.

• Cannot be used in combination with a feature that is already selected.

Normal Hidden

If a key that you wish to use is grayed out, the settings of the previous user may still be in effect. In this case, select the [Reset] key and try again.

Cannot be used because an option is not installed.

Example: When a hard disk/SSD is not installed, [Custom Box] does not appear.

2-24

Installing and Setting up the Machine > Touch Panel

Ready to copy.

EcoPrint

Off On

10:10

Cancel OK

One Touch Key No. Entry

10:10

(001 - 100)

Cancel OK

Enter key and Quick No. Search key

This section explains how to use the [Enter] key and [Quick No. Search] key on the operation panel.

Using the [Enter] key ( )

The [Enter] key has the same function as the key with the Enter mark ( ), such as the [OK  ] key and the [Close  ].

Using the [Quick No. Search] key ( )

The [Quick No. Search] key is used when using the numeric keys to directly enter the number, for example, when specifying the destination for the transmission using a speed-dial number.

For more information on speed dialing, refer to the following:

Specifying Destination (page 5-20)

2-25

Installing and Setting up the Machine > Touch Panel

Ready to copy.

Paper Selection

Auto

10:10

OKCancel

1/2

Plain

A4 Plain

Paper Selection

10:10Ready to copy.

1/2

Paper Selection

10:10Ready to copy.

1/2

1 Help titles

2 Displays information about functions

and machine operation.

3 Closes the Help screen and returns to

the original screen.

4 Scrolls up and down when the help

text cannot be displayed in its entirety on a single screen.

Help Screen

If you have difficulty operating the machine, you can check how to operate it using the touch panel.

When the [?] (help) is displayed on the touch panel, you can select it to display the Help screen. The Help screen shows explanations of functions and how to use them.

Example: Checking the paper selection Help screen

Display the Paper Selection screen.

Paper Selection (page 6-11)

2-26

Installing and Setting up the Machine > Login/Logout

NOTE

10:10

Keyboard

Login

Enter login user name and password.

Login/Logout

If you are setting a function that requires administrator rights, or if user login administration is enabled, you must enter your login user name and login password.

The factory default login user name and login password are set as shown below.

You will be unable to login if you forget your login user name or login password. In this event, login with administrator privileges and change your login user name or login password.

Normal login

Enter the login user name and login password to login.

1 If this screen is displayed during operations, select [Keyboard] to enter the login user

name.

Character Entry Method (page 11-10)

2 [Password] > Enter the login password > [OK]

If [Network Authentication] is selected as the user authentication method, authentication destinations are displayed and either [Local] or [Network] can be selected as the authentication destination.

Select [Login].

2-27

Installing and Setting up the Machine > Login/Logout

NOTE

10:10

Select the user to login.

None

1/3

Simple Login

If this screen is displayed during operations, select a user and log in.

If a user password is required, an input screen will be displayed.

Simple Login Settings (page 9-27)

Logout

To logout from the machine, select the [Authentication/Logout] key to return to the login user name/login password entry screen.

Users are automatically logged out in the following circumstances:

• When the machine enters the sleep state.

• When the auto panel reset function is activated.

2-28

Installing and Setting up the Machine > Default Settings of the Machine

NOTE

Default Settings of the Machine

Before using this machine, configure such settings as date and time, network configuration, and energy saving functions as needed. The Machine Setup Wizard is launched when the equipment is turned on for the first time after being installed. Also, configure the following settings if necessary.

The default settings of the machine can be changed in System Menu. For settings that are configurable from System Menu, refer to the following:

Setup and Registration (System Menu) (page 8-1)

Setting Date and Time

Follow the steps below to set the local date and time at the place of installation.

When you send an E-mail using the transmission function, the date and time as set here will be printed in the header of the E-mail message. Set the date, time and time difference from GMT of the region where the machine is used.

• To make changes after this initial configuration, refer to the following:

Date/Timer/Energy Saver (page 8-49)

• The correct time can be periodically set by obtaining the time from the network time server.

Command Center RX User Guide

Display the screen.

[System Menu/Counter] key > [Date/Timer/Energy Saver]

Configure the settings.

[Time Zone] > [Date/Time] > [Date Format]

Item Description

Time Zone Set the time difference from GMT. Choose the nearest listed location from

the list. If you select a region that utilizes summer time, configure settings for summer time.

Date/Time Set the date and time for the location where you use the machine. If you

perform Send as E-mail, the date and time set here will be displayed on the header.

Val ue: Year (2000 to 2037), Month (1 to 12), Day (1 to 31),

Hour (00 to 23), Minute (00 to 59), Second (00 to 59)

Date Format Select the display format of year, month, and date. The year is displayed

in Western notation.

Val ue: Month/Day/Year, Day/Month/Year, Year/Month/Day

2-29

Installing and Setting up the Machine > Network Setup

NOTE

Network Setup

Configuring the Wired Network

The machine is equipped with network interface, which is compatible with network protocols such as TCP/IP (IPv4), TCP/IP (IPv6), NetBEUI, and IPSec. It enables network printing on the Windows, Macintosh, UNIX and other platforms.

Set up TCP/IP (IPv4) to connect to the Windows network.

The configuration methods are as follows

Configuration Method Description Reference Page

Configuring the Connection from the Operation Panel on This Machine

Configuring Connections on the Web Page

Setting the Connection by Using the Setup Utility of IB-50

Be sure to connect the network cable before configuring the settings.

Connecting LAN Cable (page 2-13)

For other network settings, refer to the following:

Network (page 8-28)

If user login administration is enabled, you can only change the settings by logging in with administrator privileges. If user login administration is disabled, the user authentication screen appears. Enter a login user name and password, and select [Login].

The factory default login user name and login password are set as shown below.

Use Quick Setup Wizard when configuring the network in a wizardstyle screen, without setting individually in System menu.

For the equipped network interface, the connection can be set by using Command Center RX. For the optional IB-50, the connection can be set by using the dedicated Web page.

This is the setup tool included in the CD of IB-50. You can use it on Windows.

Quick Setup Wizard (page 2-40)

Command Center RX User Guide

IB-50 Operation Guide

2-30

Installing and Setting up the Machine > Network Setup

IMPORTANT

NOTE

IPv4 setting

Display the screen.

[System Menu/Counter] key > [System/Network] > [Network] > [Wired Network Settings] > [TCP/IP Setting] > [IPv4]

Configure the settings.

When using DHCP server

[DHCP]: Set to [On].

When setting the static IP address

[DHCP]: Set to [Off].

[IP Address]: Enter the address.

[Subnet Mask]: Enter the subnet mask in decimal representation (0 to 255).

[Default Gateway]: Enter the address.

[Auto-IP]: Set to [Off].

When using the Auto-IP, enter "0.0.0.0" in [IP Address].

After changing the setting, restart the network from System Menu, or turn the machine OFF and then ON.

Restart Network (page 8-40)

Ask your network administrator for the IP address in advance, and have it ready when you configure this setting. In the following cases, set the IP address of DNS server on the Command Center RX.

• When using the host name with "DHCP" setting set to "Off"

• When using the DNS server with IP address that is not assigned by DHCP automatically.

Setting the IP Address of the DNS Server, refer to the following:

Command Center RX User Guide

2-31

Installing and Setting up the Machine > Network Setup

NOTE

Configuring the Wireless Network

When the Wireless Network Interface Kit (IB-36 and IB-51) is installed on the machine and the connection settings are configured, it is possible to print or send in a wireless network (wireless LAN) environment. The configuration methods are as follows:

Configuration Method Description Reference Page

Configuring the Connection from the Operation Panel on This Machine

Setting the Connection by Using the Wi-Fi Setup Tool

Configuring Connections on the Web Page

Setting the Connection by Using the Setup Utility of IB-51

Use Quick Setup Wizard when configuring the network in a wizard-style screen, without setting individually in System menu.

Use Wi-Fi Settings to configure the network in details from System menu.

This is the tool included in the Product Library. You can configure the connection according to the instructions provided by the wizard.

For the IB-36, the connection can be set from the Command Center RX.

For the IB-51, the connection can be set on the dedicated Web page.

This is the setup tool included in the CD of IB-51. You can use it on both Windows and Mac OS.

Quick Setup Wizard (page 2-40)

Wi-Fi Settings (page 8-28)

Setting the Connection by Using the Wi-Fi Setup Tool (page 2-32)

Command Center RX User Guide

IB-51 Operation Guide

When you want to switch to the network interface other than Wired (default) after installing an optional Network Interface Kit (IB-50) and a Wireless Network Interface Kit (IB-36 or IB-51), select the desired setting on "Primary Network (Client)".

Primary Network (Client)

(page 8-42)

Setting the Connection by Using the Wi-Fi Setup Tool

To send the Wi-Fi settings configured in the Wi-Fi Setup Tool to the machine, connect the computer or handheld device with the machine locally. The connection methods are wired connection via LAN cable and wireless LAN connection (Wi-Fi Direct).

• Before using the Wi-Fi Setup Tool, connect your computer to this machine locally with wired LAN cable or Wi-Fi Direct.

• To use Wi-Fi Direct, confirm that the Wi-Fi Direct is enabled (Wi-Fi Direct is set to [ON]) and Restart Network from the operation panel, before your computer will be connected to this machine with Wi-Fi Direct.

• To use a wired LAN cable directly connected to the machine, the Auto-IP (Link-local) address will be assigned to the machine and the computer. This machine applies Auto-IP as the default settings.

• Configure the settings on the operation panel if your computer supports WPS.

Wi-Fi Settings

(page 8-28)

2-32

Installing and Setting up the Machine > Network Setup

NOTE

1Click [View License Agreement]

and read the License Agreement.

2Click [Accept].

Wired Connection by Using LAN Cable

Connect the machine with a computer

1 Connect the machine with a computer via LAN cable when the machine is powered on.

2 Turn on the computer.

IP address (link local address) of the machine and computer is generated automatically.

Insert the DVD.

• Installation on Windows must be done by a user logged on with administrator privileges.

• If the "Welcome to the Found New Hardware Wizard" dialog box displays, select [Cancel].

• If the autorun screen is displayed, click [Run setup.exe].

• If the user account management window appears, click [Ye s ] ([Allow]).

Display the screen.

Select [Maintenance].

[Wi-Fi Setup Tool] > [OK]

2-33

Installing and Setting up the Machine > Network Setup

NOTE

Configure the settings.

1 [Do not use automatic configuration] > [Next] > [Next]

2 [Use LAN cable] > [Next] > [Next]

3 [Easy setup] > [Next]

The machine is detected.

• Only one machine can be searched using Wi-Fi Setup Tool. It may take times to search the machine.

• If the machine is not detected, select [Advanced setup] > [Next]. Select [Express] or [Custom] as device discovery method and specify the IP address or host name to search the machine.

4 Select the machine > [Next]

5 Select [Use the device settings.] on [Authentication mode], and enter the login user

name and password. Login user name and Password are both Admin.

6 Configure the communication settings > [Next]

7 Change the settings of access point as necessary > [Next]

The network is configured.

Wireless LAN Connection by Using Wi-Fi Direct

Display the screen.

[System Menu/Counter] key > [System/Network] > [Network] > [Wi-Fi Direct Settings] > [Wi-Fi Direct]

Configure the settings.

[On] > [OK]

Restart the network.

[System Menu/Counter] key > [System/Network] > [Network] > [Restart Network] > [Yes]

Connect a computer or a handheld device with the machine.

Setting Wi-Fi Direct (page 2-36)

Insert the DVD.

2-34

Installing and Setting up the Machine > Network Setup

NOTE

1Click [View License Agreement]

and read the License Agreement.

2Click [Accept].

• Installation on Windows must be done by a user logged on with administrator privileges.

• If the "Welcome to the Found New Hardware Wizard" dialog box displays, select [Cancel].

• If the autorun screen is displayed, click [Run setup.exe].

• If the user account management window appears, click [Ye s ] ([Allow]).

Display the screen.

Select [Maintenance].

[Wi-Fi Setup Tool] > [OK]

Configure the settings.

1 [Do not use automatic configuration] > [Next] > [Next]

2 [Wi-Fi Direct] > [Next] > [Next]

3 [Advanced setup] > [Next]

Select [Express] or [Custom] as device discovery method and specify the IP address or host name to search the machine.

4 Select the machine > [Next]

5 Select [Use the device settings.] on [Authentication mode], and enter the login user

name and password. Login user name and Password are both Admin.

6 Configure the communication settings > [Next]

7 Change the settings of access point as necessary > [Next]

The network is configured.

2-35

Installing and Setting up the Machine > Network Setup

Setting Wi-Fi Direct

You can install the optional Wireless Network Interface Kit (IB-36) on the machine and configure the connection settings to print in a Wi-Fi Direct environment. The configuration methods are as follows:

Configuring the Connection from the Operation Panel on This Machine

Connecting to Computers or Handheld Devices that Support Wi-Fi Direct

Display the screen.

[System Menu/Counter] key > [System/Network] > [Network] > [Wi-Fi Direct Settings] > [Wi-Fi Direct]

Configure the settings.

[On] > [OK]

Restart the network.

[System Menu/Counter] key > [System/Network] > [Network] > [Restart Network] > [Yes]

Specify the machine name from the computer or handheld

device.

If a confirmation message appears on the operation panel of the machine, select [Yes].

The network between this machine and the handheld device is configured.

Connecting to Computers or Handheld Devices Unsupported Wi-Fi Direct

Here, we'll explain the procedures for connecting to iOS handheld devices.

Display the screen.

[System Menu/Counter] key > [System/Network] > [Network] > [Wi-Fi Direct Settings] > [Wi-Fi Direct]

Configure the settings.

[On] > [OK]

Restart the network.

[System Menu/Counter] key > [System/Network] > [Network] > [Restart Network] > [Yes]

[Home] key > [Wi-Fi Direct]

Note the network name (SSID), IP address, and password.

Configure the handheld device.

1 [Settings] > [Wi-Fi]

2 Select the network name (SSID) appeared in step 5 from the list.

3 Enter the password that was provided in step 5 > [Connect]

The network between this machine and the handheld device is configured.

2-36

Installing and Setting up the Machine > Network Setup

IMPORTANT

Configuring the Connection by Using Push Button

When your computer or handheld device does not support Wi-Fi Direct but supports WPS, you can configure the network using push button.

Display the screen.

[System Menu/Counter] key > [System/Network] > [Network] > [Wi-Fi Direct Settings] > [Wi-Fi Direct]

Configure the settings.

[On] > [OK]

Restart the network.

[System Menu/Counter] key > [System/Network] > [Network] > [Restart Network] > [Yes]

[Home] key > [Wi-Fi Direct]

Press the push button on the computer or handheld device and

select [Push Button] on the screen of operation panel simultaneously.

The network between this machine and the computer or handheld device is configured.

You can connect up to three handheld devices at the same time using Wi-Fi Direct setting. When the devices that support Wi-Fi Direct are connected, if you want to connect other device, disconnect the alreadyconnected devices from the network. The disconnection methods are as follows:

• Disconnect the network from the computer or handheld computer

• Disconnecting all devices from the network on the operation panel

Select [Home] key > [Wi-Fi Direct] > [Connected Device List] > [Disconnect All]

• Configuring auto disconnecting time from the System menu

Wi-Fi Settings

• Configuring auto disconnecting time from the Command Center RX

Command Center RX User Guide

(page 8-28)

2-37

Installing and Setting up the Machine > Energy Saver function

NOTE

Energy Saver indicator

Energy Saver function

If a certain period of time elapses after the machine is last used, the machine automatically enters Low Power Mode to reduce power consumption. If a further period of time elapses without the machine being used, the machine automatically enters Sleep Mode, which minimizes power consumption.

Low Power Mode

If the machine is not operated for a certain period of time, the energy saver indicator will light up and the screen will become dark to reduce power consumption. This status is referred to as Low Power Mode.

"Low power." will be displayed on the screen.

The amount of time before entering Low Power Mode: 1 minutes (default setting).

If print data is received during Low Power Mode, the machine automatically wakes up and starts printing. Also when fax data arrives while the machine is in Low Power Mode, the machine automatically wakes up and starts printing.

To resume, perform one of the following actions.

• Select any key on the operation panel.

• Touch the touch panel.

• Place originals in the document processor.

Recovery time from Low Power Mode is as follows.

• 10 seconds or less

Note that ambient environmental conditions, such as ventilation, may cause the machine to respond more slowly.

If the Low Power Timer is equal to the Sleep Timer, a Sleep mode is preceded.

Sleep and Auto Sleep

Sleep

To enter Sleep, select the [Energy Saver] key. Touch panel and all indicators on the operation panel will go out to save a maximum amount of power except the Energy Saver indicator. This status is referred to as Sleep.

2-38

Installing and Setting up the Machine > Energy Saver function

NOTE

If print data is received during Sleep, the machine automatically wakes up and starts printing.

Also when fax data arrives while the machine is in Sleep, the machine automatically wakes up and starts printing.

To resume, perform the following actions.

• Select the [Energy Saver] key.

The machine will be ready to operate within 25 seconds.

Note that ambient environmental conditions, such as ventilation, may cause the machine to respond more slowly.

Auto Sleep

Auto Sleep automatically switches the machine into Sleep if left idle for a preset time.

The default preset time is 1 minute.

To change the preset sleep time, refer to the following:

Quick Setup Wizard (page 2-40)

Sleep Rules (models for Europe)

You can set whether sleep mode operates for each function. When the machine enters sleep mode, the ID card cannot be recognized.

For more information on Sleep Rules settings, refer to the following:

Sleep Rules (models for Europe) (page 8-50)

Sleep Level (Energy Saver and Quick Recovery) (models except for Europe)

For sleep level, you can toggle between the following two modes: Energy Saver mode and Quick Recovery mode. The default setting is Energy Saver mode.

Energy Saver mode reduces power consumption even more than Quick Recovery mode, and allows Sleep Mode to be set separately for each function. The ID card cannot be recognized.

If the optional Network Interface Kit is installed, Energy Saver cannot be specified.

For more information on Sleep Level settings, refer to the following:

Quick Setup Wizard (page 2-40)

Power Off Rule (models for Europe)

The Power Off Rule is used to stop the power from automatically turning off.

The default preset time is 3 days.

For more information on Power Off Rule settings, refer to the following:

Power Off Rule (models for Europe) (page 8-51)

2-39

Installing and Setting up the Machine > Quick Setup Wizard

Quick Setup Wizard

For FAX functions, paper settings, Energy Saver functions and network settings, the following settings can be configured in a wizard-style screen.

FAX Setup Configures basic fax settings.

1. Dialing/RX Mode Dialing Mode

Reception Mode

Auto (DRD)

2. Local FAX Info. Local FAX Name

Local FAX Number

Local FAX ID

TTI

3. Sound Speaker Volume

Monitor Volume

Job Finish Buzzer

4. Rings Normal

Answering Machine

FAX/TEL Switch

5. Redial Retry Times

Paper Setup Configures the paper size and media type of paper to be used in cassettes and multi purpose

tray.

1. Cassette 1 Paper Size

Media Type

2. Cassette 2

Paper Size

Media Type

3. Cassette 3

Paper Size

Media Type

4. Cassette 4

Paper Size

Media Type

5. Cassette 5

Paper Size

Media Type

6. MP Tray Paper Size

Media Type

Energy Saver Setup Configures sleep mode.

1. Sleep Mode Sleep Timer

Sleep Level (models except for Europe)

2. Low Power Mode Low Power Timer

3. Weekly Timer Weekly Timer

Schedule

Retry Times

Retry Interval

2-40

Installing and Setting up the Machine > Quick Setup Wizard

NOTE

Network Setup Configures network settings.

1. Network Wi-Fi

Wi-Fi

Available Network

Wired Network Obtain IP Address

IP Address

Subnet Mask

Default Gateway

*1 Displayed only when the size dial on the cassette is set to "Other". *2 Displayed only when the optional paper feeder is installed. *3 This function is displayed when [Weekly Timer] is set to [On]. *4 This function is displayed when the optional Wireless Network Interface Kit is installed. *5 Not displayed when "Obtain IP Address" is set to [Auto (DHCP)].

If the user authentication screen appears, enter your login user name and login password and select [Login].

The factory default login user name and login password are set as shown below.

Display the screen.

[System Menu/Counter] key > [Quick Setup Wizard]

Select a function.

Configure the settings.

Start the wizard. Follow the instructions on the screen to configure settings.

[Next>]>

If you experience difficulty configuring the settings, refer to the following:

Help Screen (page 2-26)

Control Description

End Exits the wizard. Settings configured so far are applied.

Previous Returns to the previous item.

Skip Advances to the next item without setting the current item.

Next Advances to the next screen.

Back Returns to the previous screen.

Complete Register the settings and exit the wizard.

2-41

Installing and Setting up the Machine > Installing Software

NOTE

Installing Software

Install appropriate software on your PC from the included DVD (Product Library) if you want to use the printer function of this machine or perform TWAIN / WIA transmission or Network FAX transmission from your PC.

Software on DVD (Windows)

You can use either [ the standard installation method. To install components that cannot be installed by [

Express Install

] or [

Custom Install

] can be selected for the installation method. [

Express Install

], use [

For details on Custom Installation, refer to the following:

Custom Install (page 2-46)

Software Description

KX DRIVER This driver enables files on a computer to be printed by the machine.

Multiple page description languages (PCL XL, KPDL, etc.) are supported by a single driver. This printer driver allows you to take full advantage of the features of the machine.

Use this driver to create PDF files.

KX XPS DRIVER This printer driver supports the XPS (XML Paper Specification) format

developed by Microsoft Corporation.

KPDL mini-driver/PCL minidriver

FAX Driver This makes it possible to send a document created in a computer software

Kyocera TWAIN Driver This driver enables scanning on the machine using a TWAIN-compliant

This is a Microsoft MiniDriver that supports PCL and KPDL. There are some restrictions on the machine features and option features that can be used with this driver.

application as a fax via the machine.

software application.

Express Install

Custom Install

Express

Install

] is

Kyocera WIA Driver WIA (Windows Imaging Acquisition) is a function of Windows that enables

reciprocal communication between an imaging device such as a scanner and an image processing software application. An image can be acquired using a WIA-compliant software application, which is convenient when a TWAIN-compliant software application is not installed in the computer.

KYOCERA Net Viewer This is a utility that enables monitoring of the machine on the network. -

Status Monitor This is a utility that monitors the printer status and provides an ongoing

reporting function.

File Management Utility This makes it possible to send and save a scanned document to a specified

network folder.

KYOCERA Net Direct Print This makes it possible to print a PDF file without starting Adobe Acrobat/

Reader.

FONTS These are display fonts that enable the machine's built-in fonts to be used in

a software application.

Installation on Windows must be done by a user logged on with administrator privileges.

2-42

Installing and Setting up the Machine > Installing Software

NOTE

1Click [View License Agreement]

and read the License Agreement.

2Click [Accept].

Installing Software in Windows

Express Install

The following procedure is an example for installing the software in Windows 10 using [Express Install].

For details on [Custom Install], refer to the following:

Custom Install (page 2-46)

Insert the DVD.

• Installation on Windows must be done by a user logged on with administrator privileges.

• If the "Welcome to the Found New Hardware Wizard" dialog box displays, select [Cancel].

• If the autorun screen is displayed, click [Run setup.exe].

• If the user account management window appears, click [Ye s ] ([Allow]).

Display the screen.

Select [Express Install].

2-43

Installing and Setting up the Machine > Installing Software

IMPORTANT

NOTE

Install the software.

You can also select [Use host name as port name] and set to use the host name of the standard TCP/IP port. (A USB connection cannot be used.)

When you click [Install], a screen asking for your cooperation with data collection will be displayed. Select one of the answer choices and click [OK].

If Wi-Fi or Wi-Fi Direct is enabled, be sure to specify the IP address for the port name. Installation may fail if the host name is specified.

• The machine cannot be detected unless it is on. If the computer fails to detect the machine, verify that it is connected to the computer via a network or USB cable and that it

is turned on and click (Refresh).

• If the Windows security window appears, click [Install this driver software anyway].

• To install Status Monitor on Windows versions preceding Windows 8, it is necessary to install Microsoft .NET Framework 4.0 beforehand.

2-44

Installing and Setting up the Machine > Installing Software

Finish the installation.

When "Your software is ready to use." appears, you can use the software. To print a test page, click the "Print a test page" checkbox and select the machine.

Click [Finish] to exit the wizard.

If a system restart message appears, restart the computer by following the screen prompts. This completes the printer driver installation procedure.

If you are installing the TWAIN driver, continue by configuring the following:

Setting TWAIN Driver (page 2-52)

2-45

Installing and Setting up the Machine > Installing Software

NOTE

1 Click [View License Agreement]

and read the License Agreement.

2 Click [Accept].

Custom Install

The following procedure is an example for installing the software in Windows 10 using [Custom Install].

Insert the DVD.

• Installation on Windows must be done by a user logged on with administrator privileges.

• If the "Welcome to the Found New Hardware Wizard" dialog box displays, select [Cancel].

• If the autorun screen is displayed, click [Run setup.exe].

• If the user account management window appears, click [Ye s ] ([Allow]).

Display the screen.

Select [Custom Install].

Install the software.

1 Select the device to be installed.

2-46

Kyocera M3860IDNF, M3860IDN User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Preface

Contents

Overview

Machine Features

Color and Image Quality Functions

Basic Color Modes

Adjusting Image Quality and Color

Guides Provided with the Machine

About the Operation Guide (this Guide)

Structure of the guide

Conventions Used in This Guide

Menu Map

Notice

Safety Conventions in This Guide

Environment

Precautions for Use

Laser Safety (Europe)

SAFETY OF LASER BEAM (USA)

Safety Instructions Regarding the Disconnection of Power

Compliance and Conformity

Other precautions (for users in California, the United States)

Warranty (the United States and Canada)

Legal Restriction on Copying/Scanning

EN ISO 7779

EK1-ITB 2000

Wireless Connection (Mexico only)

Security Precautions when Using Wireless LAN (If equipped)

Limited Use of This Product (If equipped)

Legal Information

Energy Saving Control Function

Automatic 2-Sided Print Function

Resource Saving - Paper

Environmental benefits of "Power Management"

Energy Star (ENERGY STAR®) Program

Part Names

Machine Exterior

Connectors/Interior

With Optional Equipments Attached

Connecting the Machine and Other Devices

Connecting Cables

Connecting LAN Cable

Connecting USB Cable

Connecting the Power Cable

Power On/Off

Power On

Power Off

Using the Operation Panel

Operation Panel Keys

Adjusting the Operation Panel Angle

Touch Panel

Home Screen

Display for Device Information

Functions key

Display of Keys That Cannot Be Set

Enter key and Quick No. Search key

Help Screen

Login

Login/Logout

Logout

Default Settings of the Machine

Setting Date and Time

Network Setup

Configuring the Wired Network

Configuring the Wireless Network

Setting Wi-Fi Direct

Energy Saver function

Low Power Mode

Sleep and Auto Sleep

Power Off Rule (models for Europe)

Quick Setup Wizard

Installing Software

Software on DVD (Windows)

Installing Software in Windows