Kymco MO KXR 50 Service Manual - chap 10 (riduzione finale)

Page 1
10.FINAL REDUCTION/
TRANSMISSION SYSTEM
10-0
Mongoose/KXR 90/50
10
FINAL REDUCTION/TRANSMISSION SYSTEM
SERVICE INFORMATION -------------------------------------------- 10- 2
TRANSMISSION CASE COVER------------------------------------------ 10- 3
10
Page 2
10.FINAL REDUCTION/
TRANSMISSION SYSTEM
10-1
Mongoose/KXR 90/50
Page 3
10.FINAL REDUCTION/
TRANSMISSION SYSTEM
10-2
Mongoose/KXR 90/50
SERVICE INFORMATION
GENERAL INSTRUCTIONS
The transmission system can be serviced with the engine installed in the frame.
When replacing the drive shaft, use a special tool to hold the bearing inner race for this operation.
SPECIFICATIONS
Specified Oil: GEAR OIL SAE 90# Oil Capacity: At change : 0.11 liter
At disassembly : 0.12 liter
TORQUE VALUES
Transmission case cover bolt 2.4_ 3.0kgf-m
TROUBLESHOOTING
Engine starts but ATV won‘t move
Damaged transmission
Seized or burnt transmission
Oil leaks
Oil too rich
Worn or damaged oil seal
Page 4
10.FINAL REDUCTION/
TRANSMISSION SYSTEM
10-3
Mongoose/KXR 90/50
TRANSMISSION CASE COVER
REMOVAL
Remove the drive sprocket. (!6-2) Remove the left crankcase cover. (!9-2) Remove the clutch/driven pulley. (!9-10) Drain the transmission gear oil into a clean container. Remove the transmission case cover attaching bolts. Remove the transmission case cover. Remove the gasket and dowel pins.
Inspect the bearings for allow play in the transmission case cover or the bearings turn roughly.
If any defects are found, replace the bearing with a new one.
Inspect the final shaft bearing oil seal for wear or damage.
Remove the final gear and countershaft.
Inspect the bearings for allow play in the transmission case cover or the bearing turns roughly.
If any defects are found, replace the bearing with a new one.
Bearings
Transmission Cover
Bolts
Transmission Case Cover
Final Gear
Oil Seal
Countershaft
Bearings
Do not remove the transmission case cover except for necessary part replacement. When replacing the drive shaft, also replace the bearing and oil seal.
Page 5
10.FINAL REDUCTION/
TRANSMISSION SYSTEM
10-4
Mongoose/KXR 90/50
PRIMARY DRIVE AXLE REMOVAL
Remove the clutch/friven pulley. (Refer to chapter 9)
Remove the primary drive axle.
Inspect the final gear teeth. Blue discoloration/pitting/wear _ Replace.
Inspect the countershaft gear teeth. Blue discoloration/pitting/wear _ Replace.
Primary Drive Axle
Page 6
10.FINAL REDUCTION/
TRANSMISSION SYSTEM
10-5
Mongoose/KXR 90/50
INSTALLATION
Reverse the “TRANSMISSION REVOVAL” section procedures. Install the primary drive axle into the left crankcase.
Install the final gear and final shaft into left crankcase.
Install the countershaft and washer into the left crankcase.
Install the resin washer onto countershaft.
Install the dowel pins and a new gasket onto the right crankcase.
Install the transmission case cover and tighten the transmission case cover bolt.
Torque: 2.4_ 3.0kgf-m
Primary Drive Axle
Final Shaft
Countershaft
Resin Washer
Gasket
Dowel Pins
Page 7
10.FINAL REDUCTION/
TRANSMISSION SYSTEM
10-6
Mongoose/KXR 90/50
Fill the engine with oil and install the oil filler bolt. (Refer to the “TRANSMISSION OIL REPLACEMENT” section in the chapter 3)
Specified Gear Oil: KYMCO SIGMA GEAR OIL 90#
Oil Capacity:
At disassembly : 0.12 liter At change : 0.11liter
Loading...