Konica Minolta AccurioPress C3080, AccurioPress C3080P, AccurioPress C3070, AccurioPrint C3070L, EF-103 User Manual

AccurioPress C3080/C3080P/C3070, AccurioPrint C3070L Contents-1

Contents

1 Introduction

1.1 Introduction ..................................................................................................................................... 1-2

1.2 Safety Precautions.......................................................................................................................... 1-3

1.2.1 Notices for Safety .............................................................................................................................. 1-3

1.2.2 Precautions When Replacing Units ................................................................................................... 1-4

1.2.3 Warning and Caution Labels.............................................................................................................. 1-6

2 Installing Fusing Unit EF-103

2.1 Replacement Parts ......................................................................................................................... 2-2

2.2 Installation Procedures .................................................................................................................. 2-4

2.2.1 Installing Fusing Unit EF-103 on the Main Body................................................................................ 2-4

2.2.2 Installing Parts in the Tray (when Paper Feeder Unit PF-707m is installed) ...................................... 2-7

2.2.3 Installing Parts in the Tray (when Large Capacity Unit LU-202m/LU-202XL/LU-202XLm is installed) 2­10

3 Removing Fusing Unit EF-103

3.1 Removal Procedures ...................................................................................................................... 3-2

3.1.1 Removing Fusing Unit EF-103 from the Main Body .......................................................................... 3-2

3.1.2 Removing Parts from the Tray (when Paper Feeder Unit PF-707m is installed)................................ 3-2

3.1.3 Removing Parts from the Tray (when Large Capacity Unit LU-202m/LU-202XL/LU-202XLm is installed)
3-2

4 Copy/Print Operation

4.1 Loading Envelopes in the Tray....................................................................................................... 4-2

4.1.1 Loading Envelopes in the Tray 5 of Paper Feeder Unit PF-707m ..................................................... 4-3

4.1.2 Loading Envelopes in Large Capacity Unit LU-202m/LU-202XL/LU-202XLm .................................. 4-3

4.2 Copy Operation ............................................................................................................................... 4-8

4.3 Print Operation.............................................................................................................................. 4-13

5 Specifications

5.1 Specifications of Fusing Unit EF-103 ............................................................................................................... 5-2

1

Introduction

AccurioPress C3080/C3080P/C3070, AccurioPrint C3070L 1-2

1.1 Introduction

1

1 Introduction

1.1 Introduction

Notice to Users of Fusing Unit EF-103

When replacing the machine units, please follow the instructions described in the User's Guide.

To perform replacement tasks safely and reliably, keep this User's Guide and do not lose them. If you lose
the document, please contact your service representative.

Registered Trademarks

KONICA MINOLTA, the KONICA MINOLTA logo, and the symbol are registered trademarks or trademarks of
KONICA MINOLTA, INC.

AccurioPress/AccurioPrint are registered trademarks or trademarks of KONICA MINOLTA, INC.

Copyright ©

2018 KONICA MINOLTA, INC.

AccurioPress C3080/C3080P/C3070, AccurioPrint C3070L 1-3

1.2 Safety Precautions

1

1.2 Safety Precautions

1.2.1 Notices for Safety

The followings are what you need to follow to safely replace the units. Please be sure to read the precautions
before replacing the units.

- Keep the User's Guide at hand for your future reference and be careful not to lose it.

- Make sure you follow the safety precautions listed in the User's Guide.

Warning and precaution symbols

Be sure to observe the safety precautions.

- This manual contains the instructions that should be strictly observed at all times to prevent injury to

yourself and other persons as well as damage to property.

Injuries and damage that might be caused by using the product improperly are classified according to the
following symbols.

These are some of major exemplary graphical symbols.

Pictorial indication Description

Improper handling can cause serious injury or death.

Improper handling can cause minor injury or damage to houses and
property.

Graphic
symbols

Description Graphic

symbols

Description Graphic

symbols

Description

General
Prohibited

Do not 
disassemble

Do not touch

Instructions Ground/Earth

Unplug from
outlet

General
precaution

High 
temperature

Electrical
shock hazard

AccurioPress C3080/C3080P/C3070, AccurioPrint C3070L 1-4

1.2 Safety Precautions

1

1.2.2 Precautions When Replacing Units

Preparation Tasks Before Replacing Units

Unit Replacement Tasks

When replacing the units, be sure to receive instructions from our
customer engineer, read the User' Guide in entirety and perform
tasks in the specified order with appropriate tools. Do not perform
any tasks that are not described in the User's Guide. Failure to fol­low specified order or use appropriate tools could result in injury
or physical damage to the product.

Please be careful when handling the fusing unit since it can be
very hot. It could cause a burn.

Keep this bag away from babies and children. Do not use in cribs,
beds, carriages, or playpens. The thin film may cling to nose and
mouth and prevent breathing. This bag is not a toy.

Do not drop metal pieces such as clips, staples and screws inside
the product or into crevices in it.
They could cause a short-circuit in the product, resulting in an
electric shock or a fire.

Ensure cables are not pinched or damaged.
It could cause an electric shock or a fire due to electric leakage.

Do not place the unit removed in the replacement tasks on an un­stable table or sloped surface, or in a location subject to excessive
shocks or vibrations. It could drop or fall and may cause personal
injury.

Please pay careful attention to the surroundings when placing the
unit removed in the replacement tasks.
Protruding portions, cords or wires of the unit may cause falling or
personal injury.

AccurioPress C3080/C3080P/C3070, AccurioPrint C3070L 1-5

1.2 Safety Precautions

1

Power Plug

Actions in Response to Troubles

Do not unplug or plug in the power cord with a wet hand, as you
could receive an electrical shock.

Plug the power cord all the way into the power outlet. Failure to do
this could result in a fire or an electrical shock.

Do not tug the power cord when unplugging. Tugging the cord to
do this could damage it, resulting in a fire, electrical shock, or
breakdown.

Do not place any objects around the power plug, as the power
plug may be difficult to pull out when an emergency occurs.

Remove the power plug from the outlet more than one time a year
and clean the area between the plug terminals. Dust that accumu­lates between the plug terminals may cause a fire.

Do not keep using this product, if this product becomes inordi­nately hot or emits smoke, or unusual odor or noise. Immediately
turn OFF the power switch, unplug the power cord from the power
outlet, and then call your Technical Representative or your autho­rized service representative. If you keep on using it as is, a fire or
electrical shock could result.

Do not keep using this product, if this product has been dropped
or its cover damaged. Immediately turn OFF the power switch, un­plug the power cord from the power outlet, and then call your
Technical Representative or your authorized service representa­tive. If you keep on using it as is, a fire or electrical shock could
result.

The inside of this product has areas subject to high temperature,
which may cause burns. When checking the inside of the unit for
a unit replacement and others, do not touch the locations (around
the fusing unit, etc.) which are indicated by a "Caution HOT" cau­tion label. A burn could result.

AccurioPress C3080/C3080P/C3070, AccurioPrint C3070L 1-6

1.2 Safety Precautions

1

1.2.3 Warning and Caution Labels

This machine has warning label, caution labels and indicators for safety precaution in the following location.
These labels and indicators advise you to pay special attention to avoid any dangerous situations or serious
injury when you replace the units.

7CAUTION

DO NOT remove warning or caution labels.

- Should any warning or caution label be removed, you may fail to check a specific part to be alert for

unexpected trouble or injury. If you find any warning or caution label removed or illegible due to soilage,
please contact your service representative.

Caution Labels on Fusing Part of Conveyance Fixing Unit

CAUTION: High temperature! Burn

You may get burned.
DO NOT touch the fusing part of the conveyance fixing unit.
Be especially careful when withdrawing the conveyance fixing unit or opening the fusing
part.

CAUTION: Injury

You may get injured.
DO NOT put your hands or arms in between the main body and the conveyance fixing unit.
Touching connecting terminals of electric parts may damage the machine or cause unex­pected trouble.
Please do not try to work yourself, but contact your service representative.

2

Installing Fusing Unit EF-103

AccurioPress C3080/C3080P/C3070, AccurioPrint C3070L 2-2

2.1 Replacement Parts

2

2 Installing Fusing Unit EF-103

When replacing the fusing unit, follow the precautions below to perform the task.

NOTICE

When replacing the fusing unit, be sure to receive instructions from our customer engineer.

NOTICE

Please do not dispose of the packaging box of Fusing Unit EF-103. Keep the packaging box and reuse it to
store the replaced fusing unit.

NOTICE

Multi Bypass Tray MB-506, Paper Feeder Unit PF-707m, and Large Capacity Unit LU-202m/LU-202XL/LU­202XLm are used as a paper feed tray only when they are installed directly on the main body.

With Paper Feeder Unit PF-707m installed, only tray 5 (the lower tray) can be used as a paper source. All the
other trays are unavailable.

7WARNING

- Keep this bag away from babies and children. Do not use in cribs, beds, carriages, or playpens. The

thin film may cling to nose and mouth and prevent breathing. This bag is not a toy.

2.1 Replacement Parts

PN Name Shape Q’ty

1 Fusing Unit EF-103 1

2 Side auxiliary guide *

1

2

3 Rear assist guide/Lw*

2

1

4 Rear assist guide/Up*

2

1

AccurioPress C3080/C3080P/C3070, AccurioPrint C3070L 2-3

2.1 Replacement Parts

2

*1: Packaged together with the Fusing Unit EF-103. Use this part when Paper Feeder Unit PF-707m is in­stalled on the main body.

*2: Packaged together with the Fusing Unit EF-103. Use this part when Paper Feeder Unit PF-707m is in­stalled on the main body and when the width of the envelope you use is from 100 to 140 mm.

*3: Packaged together with the Mount Kit MK-746. Use this part when Large Capacity Unit LU-202m/LU­202XL/LU-202XLm is installed on the main body.

5 Bottom auxiliary guide assy[A] *

3

1

6 Side auxiliary guide assy[B] *

3

2

7 Tip auxiliary guide/rear assy[C] *

3

1

8 Tip auxiliary guide/front assy[C] *

3

1

9 Bottom auxiliary plate assy[D] *

3

1

10 Adjusting block assy *

3

2

11 Guide shaft *

3

1

PN Name Shape Q’ty

AccurioPress C3080/C3080P/C3070, AccurioPrint C3070L 2-4

2.2 Installation Procedures

2

2.2 Installation Procedures

2.2.1 Installing Fusing Unit EF-103 on the Main Body

1 Turn off the machine's sub and main power switches, and then unplug the power cord from the outlet.

% Be sure to turn off the sub power switch first.

2 Open the front door [1].

3 To pull out the conveyance fixing unit [3], push the lock [2]

of the lever M1 [1] to the left, then turn the lever M1 [1]
counterclockwise.

NOTICE

Please confirm that process unit has not been pulled out
when pulling out the conveyance fixing unit.

4

Open the paper exit guide [2] while releasing the lever M6 [1]
at the bottom.

Loosen the screw [3] (1 piece).

AccurioPress C3080/C3080P/C3070, AccurioPrint C3070L 2-5

2.2 Installation Procedures

2

5 Pull out the fixing plate [1] forward.

6 Holding the handles on the rear and front sides [2] of the

fusing unit [1] by both hands, slide the fusing unit [1] for­ward to the position of arrow mark.

Please be careful when working on the fusing unit; the unit
is extremely hot.

7 Holding the handles on the rear and front sides [2] of the

fusing unit [1] by both hands, remove the fusing unit [1].

Place the removed fusing unit on the flat surface.

8 Holding the handles on the front and rear sides [2] of Fus-

ing Unit EF-103 [1] with both hands, set Fusing Unit EF­103 [1] on the fixing position with arrow mark.

NOTICE

Make sure that the exit section is open before setting Fus­ing Unit EF-103 to the machine. When you try to set the
fusing unit with the exit guide unit closed, the machine may
be damaged.

AccurioPress C3080/C3080P/C3070, AccurioPrint C3070L 2-6

2.2 Installation Procedures

2

9 Holding the handles on the front and rear sides [2] of Fus-

ing Unit EF-103 [1] with both hands, slide it to the direction
of arrow until it knocks in place.

Return the fixing plate [3] to its original position.

10

Tighten the screw [1] (1 piece) and close the exit section [2].

Insert the conveyance fixing unit [3].

11 Raise the lever M1 [1] by turning it clockwise.

12 Close the front door [1].

13 Store the removed fusing unit in the empty packaging of

Fusing Unit EF-103.

NOTICE

Please wait until the fusing unit gets cold before storing it
in the packaging.

AccurioPress C3080/C3080P/C3070, AccurioPrint C3070L 2-7

2.2 Installation Procedures

2

2.2.2 Installing Parts in the Tray (when Paper Feeder Unit PF-707m is installed)

Depending on the size of the envelope to be used, the attached auxiliary guides need to be installed on Paper
Feeder Unit PF-707m.

For details on the envelope size, refer to page 5-2.

NOTICE

Trays cannot be withdrawn when the machine is not powered. Plug the power cord of the machine into the
outlet, turn on the main power switch, then the sub power switch before performing the installation.

Using Envelopes of 100 to 139.7 mm in Width

The following parts need to be installed when envelopes of the above size are used.

- Side auxiliary guide (2 pieces)

- Rear assist guide/Lw (1 piece)

- Rear assist guide/Up (1 piece)

To use envelopes smaller than 139.7mm, use the small size guides of Paper Feeder Unit PF-707m.

1 Pull out tray 5.

2 Open the small size guides (front/rear) to the direction of

arrow to set the guides to the positions illustrated below.

3 Insert the side auxiliary guides (2 pieces) into the position-

ing screws on the side guides.

AccurioPress C3080/C3080P/C3070, AccurioPrint C3070L 2-8

2.2 Installation Procedures

2

NOTICE

Do not move the paper control levers (2 pieces). Other­wise, the paper feeding performance may degrade.

4 Install the rear assist guide/Lw.

% Hit the rear assist guide/Lw to the gap of the rear guide

plate.

5 Install the rear assist guide/Up to the rear guide.

6 Push in tray 5 until it locks into place.

Using Envelopes of 139.7 to 245 mm in Width

Follow the procedure below to use envelopes of the above size. Side auxiliary guides (2 pieces) are not need­ed.

1 Pull out tray 5.

2 Move each of the small size guides (front/rear) toward the

outside the side guide plates.

% If the auxiliary guides are installed on the side guides,

pull them up to remove them. The positioning screws
(4 pieces) installed on the side guides are not required

AccurioPress C3080/C3080P/C3070, AccurioPrint C3070L 2-9

2.2 Installation Procedures

2

to be removed.

3 Push in tray 5 until it locks into place.

AccurioPress C3080/C3080P/C3070, AccurioPrint C3070L 2-10

2.2 Installation Procedures

2

2.2.3 Installing Parts in the Tray (when Large Capacity Unit LU-202m/LU­202XL/LU-202XLm is installed)

The auxiliary parts that need to be installed to the Large Capacity Unit LU-202m/LU-202XL/LU-202XLm vary
depending on the size of the envelope to be used.

For details on the envelope size, refer to page 5-2.

Using C5, C6/C5, or 6x9 1/2 Envelopes

The following parts need to be installed when C5, C6/C5, or 6x9 1/2 envelopes are used.

- Bottom auxiliary guide assy [A] (1 piece)

- Adjusting block assy (2 pieces)

- Tip auxiliary guide/rear assy [C] (1 piece)

- Tip auxiliary guide/front assy [C] (1 piece)

- Bottom auxiliary plate assy [D] (1 piece)

- Guide shaft (1 piece)

Follow the procedure below to use envelopes of the above size. Auxiliary guides (2 pieces) are not needed.

1 Open the upper door.

2 Remove the holding paper.

% Hold the projection with your fingers and slide the hold-

ing paper in the arrowed direction, and remove it.

3 Install the bottom auxiliary guide assy [A] in the Large Ca-

pacity Unit LU-202m/LU-202XL/LU-202XLm tray.

% Align the positioning pin of the bottom auxiliary guide

assy [A] with the installation hole of the tray.

% Align the detent of the bottom auxiliary guide assy [A]

with the groove on the back end guide.

AccurioPress C3080/C3080P/C3070, AccurioPrint C3070L 2-11

2.2 Installation Procedures

2

4 Align the adjusting block assies (2 pieces) to C5, C6/C5,

and 6x9 1/2 on the indicating label, and install them.

% Align the mark on the adjusting block assy with the

mark on the indicating label.

5 Install the tip auxiliary guide/rear assy [C] (1 piece) and the

tip auxiliary guide/front assy [C] (1 piece) to the paper
guide side plate.

% Align the installation hole in the tip auxiliary guide assy

with the positioning pin.

% Align the cutout of the tip auxiliary guide assy with the

positioning collar.

6 Align the bottom auxiliary plate assy [D] with the mark line

on the bottom auxiliary guide assy [A]. Align the edge of the
PET sheet with the edge of the bottom auxiliary guide assy
[A]. Then, install them.

6x9 1/2 (152 x 241 mm)
C5 (162 x 229 mm)
C6/C5 (114 x 229 mm)

AccurioPress C3080/C3080P/C3070, AccurioPrint C3070L 2-12

2.2 Installation Procedures

2

7 Install the guide shaft to the back edge guide base of the

bottom auxiliary guide assy [A].

8 Close the upper door.

Using K2 (240 x 332 mm) Envelopes

The following parts need to be installed when K2 envelopes are used.

- Bottom auxiliary guide assy [A] (1 piece)

- Adjusting block assy (2 pieces)

- Guide shaft (1 piece)

1 Open the upper door.

2 Remove the holding paper.

% Hold the projection with your fingers and slide the hold-

ing paper in the arrowed direction, and remove it.

3 Install the bottom auxiliary guide assy [A] in the Large Ca-

pacity Unit LU-202m/LU-202XL/LU-202XLm tray.

% Align the positioning pin of the bottom auxiliary guide

assy [A] with the installation hole of the tray.

% Align the detent of the bottom auxiliary guide assy [A]

with the groove on the back end guide.

AccurioPress C3080/C3080P/C3070, AccurioPrint C3070L 2-13

2.2 Installation Procedures

2

4 Align the adjusting block assies (2 pieces) to K2 on the in-

dicating label, and install them.

% Align the mark on the adjusting block assy with the

mark on the indicating label.

5 Install the guide shaft to the back edge guide base of the

bottom auxiliary guide assy [A].

6 Close the upper door.

K2 (240 x 332 mm)

AccurioPress C3080/C3080P/C3070, AccurioPrint C3070L 2-14

2.2 Installation Procedures

2

Using N4 (90 x 205 mm) or N3 (120 x 235 mm) Envelopes

The following parts need to be installed when N4 or N3 envelopes are used.

- Bottom auxiliary guide assy [A] (1 piece)

- Adjusting block assy (2 pieces)

- Side auxiliary guide assy [B] (2 pieces)

- Guide shaft (1 piece)

1 Open the upper door.

2 Remove the holding paper.

% Hold the projection with your fingers and slide the hold-

ing paper in the arrowed direction, and remove it.

3 Install the bottom auxiliary guide assy [A] in the Large Ca-

pacity Unit LU-202m/LU-202XL/LU-202XLm tray.

% Align the positioning pin of the bottom auxiliary guide

assy [A] with the installation hole of the tray.

% Align the detent of the bottom auxiliary guide assy [A]

with the groove on the back end guide.

4 Align the adjusting block assies (2 pieces) to N4 and N3 on

the indicating label, and install them.

% Align the mark on the adjusting block assy with the

mark on the indicating label.

N4 (90 x 205 mm), 
N3 (120 x 235mm)

AccurioPress C3080/C3080P/C3070, AccurioPrint C3070L 2-15

2.2 Installation Procedures

2

5 Install the side auxiliary guide assy [B] to the paper guide

side plate. (2 places)

% Be sure to align the installation holes in the side auxil-

iary guide assy with the positioning screws.

NOTICE

Turn the machine power on, and lower the tray bottom
plate to the lowest place by pressing the tray bottom plate
lowering button of the Large Capacity Unit LU-202m/LU­202XL/LU-202XLm, and then install the side auxiliary
guide assy [B]. An incorrect setting may result in damage
to the machine.

6 Install the guide shaft to the back edge guide base of the

bottom auxiliary guide assy [A].

7 Close the upper door.

Using K1 (270 x 382 mm) or K0 (287 x 382 mm) Envelopes

The following parts need to be installed when K1 or K0 envelopes are used.

- Bottom auxiliary guide assy [A] (1 piece)

- Adjusting block assy (2 pieces)

- Bottom auxiliary plate assy [D] (1 piece)

NOTICE

In the case of K1 or K0 envelopes, depending on the curl direction, the paper can also be fed without the use
of auxiliary parts. For details, refer to

page 2-16

.

1 Open the upper door.

2 Remove the holding paper.

% Hold the projection with your fingers and slide the hold-

ing paper in the arrowed direction, and remove it.

% Check the curl direction at the leading edge of the en-

velope, and remove the holding paper, if necessary.

Bottom plate lowering button

AccurioPress C3080/C3080P/C3070, AccurioPrint C3070L 2-16

2.2 Installation Procedures

2

3 Install the bottom auxiliary guide assy [A] in the Large Ca-

pacity Unit LU-202m/LU-202XL/LU-202XLm tray.

% Check the curl direction at the leading edge of the en-

velope, and remove the holding paper, if necessary.

% Align the positioning pin of the bottom auxiliary guide

assy [A] with the installation hole of the tray.

% Align the detent of the bottom auxiliary guide assy [A]

with the groove on the back end guide.

4 Hold the flap of the envelope to use and droop vertically.

5 Put the leading edge on a flat surface to check the curl di-

rection and that the curl amount is 8 mm or less.

Downward curl: With MK-746 (refer to Step 8 and later)

Upward curl: Without MK-746

NOTICE

Envelopes with 8 mm or more curl amount are not guaran­teed.

6 Align the adjusting block assies (2 pieces) to K1 and K0 on

the indicating label, and install them.

% Align the mark on the adjusting block assy with the

mark on the indicating label.

Upward curl

Downward curl

Curl amount

8mm or
less

Curl direction

K1 (270 x 382 mm)
K0 (287 x 382 mm)

AccurioPress C3080/C3080P/C3070, AccurioPrint C3070L 2-17

2.2 Installation Procedures

2

7 Align the bottom auxiliary plate assy [D] with the mark line

on the bottom auxiliary guide assy [A]. Align the edge of the
PET sheet with the edge of the bottom auxiliary guide assy
[A]. Then, install them.

% Be sure to move the back edge guide base to the end

edge.

8 Close the upper door.

Back edge
guide base

3

Removing Fusing Unit EF-103

AccurioPress C3080/C3080P/C3070, AccurioPrint C3070L 3-2

3.1 Removal Procedures

3

3 Removing Fusing Unit EF-103

This section describes the procedures to remove Fusing Unit EF-103 and the feed auxiliary parts for enve­lopes.

When using paper other than envelopes, follow the procedure below to replace the fusing unit and remove
the parts installed in the tray.

3.1 Removal Procedures

3.1.1 Removing Fusing Unit EF-103 from the Main Body

When you remove Fusing Unit EF-103 from the main body, follow the installation procedure in reverse. For
the installation procedure of Fusing Unit EF-103 to the main body, please refer to page 2-4.

3.1.2 Removing Parts from the Tray (when Paper Feeder Unit PF-707m is installed)

When you remove the auxiliary guides (2 pieces) installed on the side guide of tray 5, follow the installation
procedure in reverse. For the installation procedure of parts to the tray, please refer to page 2-7.

NOTICE

Trays cannot be withdrawn when the machine is not powered. Plug the power cord of the machine into the
outlet, turn on the main power switch, then the sub power switch before removing parts from the tray.

3.1.3 Removing Parts from the Tray (when Large Capacity Unit LU-202m/LU­202XL/LU-202XLm is installed)

When you remove parts from the tray, follow the installation procedure in reverse. For the installation proce­dure of parts to the tray, please refer to page 2-10.

4

Copy/Print Operation

AccurioPress C3080/C3080P/C3070, AccurioPrint C3070L 4-2

4.1 Loading Envelopes in the Tray

4

4 Copy/Print Operation

This section describes how to load envelopes in the tray with the parts for envelopes installed, and to
copy/print onto those envelopes.

4.1 Loading Envelopes in the Tray

Envelopes with the following specifications can be loaded in the tray.

NOTICE

It is recommended to use L-seam or side seam envelopes; the print results may be blurred if tabs overlap
with the print side.

dReference

For details on how to load paper in the tray, refer to the HTML user's guide.

Paper size Width: 100 to 245 mm (3.92" to 9.63"), Length: 148 to 375 mm (5.82" to

14.73")

- Use auxiliary guides to load envelopes of 100 to 140 mm (3.92" to 5.50")

in width when Paper Feeder Unit PF-707m is installed.

Paper weight 70 to 100 g/m

2

(19 to 27 lb Bond)

Tray capacity Multi Bypass Tray MB-506: 1 sheet

Other paper trays: 100 sheets (6" x 9-1/2", C5, C6/C5, K2, N3, N4*)

50 sheetsv (K0, K1)
*: The N4 envelope is supported only when the Large Capacity Unit LU­202m/LU-202XL/LU-202XLm is installed.

Unsuitable envelopes Envelopes with a film window

Envelopes with a double-stick tape or release coated paper on the flap

AccurioPress C3080/C3080P/C3070, AccurioPrint C3070L 4-3

4.1 Loading Envelopes in the Tray

4

4.1.1 Loading Envelopes in the Tray 5 of Paper Feeder Unit PF-707m

1 Pull out tray 5.

2 Widen the side guides and rear guide.

3 Place envelopes with the print side up.

% Align the envelopes to the left side of the tray with the

flaps on the right.

4 Align the side guides and rear guide to the edge of the envelopes.

NOTICE

Do not apply excessive force when moving the side guides. Otherwise, the guides may be damaged.

5 Push in tray 5 until it locks into place.

4.1.2 Loading Envelopes in Large Capacity Unit LU-202m/LU-202XL/LU-202XLm

Using K2 (240 x 332 mm) Envelopes

NOTICE

If jam occurs frequently when you load a very small number of K2 envelopes having a paper weight of 80
g/m

2

or less, follow steps 6 and 7.

1 Open the upper door.

2 Bend and set the envelope as shown in the right figure.

AccurioPress C3080/C3080P/C3070, AccurioPrint C3070L 4-4

4.1 Loading Envelopes in the Tray

4

% Be sure to set the envelopes so that both sides of their

leading edge and their flaps do not droop.

3 Adjust the guide shaft to the size of the envelope.

OK

NG

AccurioPress C3080/C3080P/C3070, AccurioPrint C3070L 4-5

4.1 Loading Envelopes in the Tray

4

4 Adjust both paper guide side plates to the size of the en-

velop.

5 Close the upper door.

<If jam occurs frequently when you load a very small number of K2 envelopes having a paper weight
of 80 g/m

2

or less>

6 Remove the front edge lift up materials from the side of the

bottom auxiliary guide assy [A].

7 Install the front edge lift up materials on the bottom auxil-

iary guide assy [A] as shown in the right figure.

AccurioPress C3080/C3080P/C3070, AccurioPrint C3070L 4-6

4.1 Loading Envelopes in the Tray

4

Using N4 (90 x 205 mm) or N3 (120 x 235 mm) Envelopes

1 Open the upper door.

2 Set N4 or N3 envelopes on the bottom auxiliary guide assy

[A], and adjust the guide shaft to the size of the envelope
moving it to right and left.

3 Adjust both paper guide side plates to the size of the en-

velop.

4 Close the upper door.

Using K1 (270 x 382 mm) or K0 (287 x 382 mm) Envelopes

1 Open the upper door.

2 Bend and set the envelope as shown in the right figure.

3 Adjust the back edge restriction plate to the size of the en-

velope.

<For Large Capacity Unit LU-202m>

AccurioPress C3080/C3080P/C3070, AccurioPrint C3070L 4-7

4.1 Loading Envelopes in the Tray

4

<For Large Capacity Unit LU-202XL/LU-202XLm>

4 Adjust both paper guide side plates to the size of the en-

velop.

5 Close the upper door.

Using C5, C6/C5, or 6x9 1/2 Envelopes

1 Open the upper door.

2 Set the envelops to use on the bottom auxiliary guide assy

[A], and adjust the guide shaft to the size of the envelope
moving it to right and left.

3 Adjust both paper guide side plates to the size of the en-

velop.

4 Close the upper door.

AccurioPress C3080/C3080P/C3070, AccurioPrint C3070L 4-8

4.2 Copy Operation

4

4.2 Copy Operation

In order to copy on envelopes, the paper setting for the tray must be modified from [Paper Setting] on the
Machine Screen or [Paper Setting] on the Copy Screen.

This section describes how to change [Paper Setting] on the Machine Screen and then to start copy opera­tions.

d Reference

For details on Paper Setting, how to load originals, and how to make copy settings, refer to the HTML user's
guide.

0 With Multi Bypass Tray MB-506 installed on the main body, only bypass tray can be selected. With Pa-

per Feeder Unit PF-707m installed, only tray 5 (the lower tray) can be selected. With Large Capacity
Unit LU-202m/LU-202XL/LU-202XLm installed, only tray 3 can be selected.

0 The paper type and size are automatically fixed to [Envelope] and [Custom].

0 The width and length of envelopes can be entered in the custom size setting. For details on the width

and length of the envelopes, refer to page 5-2.

0 The print side is automatically limited to simplex, and the output side to Face Up.

1 Press [Paper Setting] on the Machine Screen.

2 Select the tray, and then press [Recall].

% When you install Multi Bypass Tray MB-506, select [Bypass].
% When you install Paper Feeder Unit PF-707m, select [Tray5].
% When you install Large Capacity Unit LU-202m/LU-202XL/LU-202XLm, select [Tray3].

AccurioPress C3080/C3080P/C3070, AccurioPrint C3070L 4-9

4.2 Copy Operation

4

% If any paper setting for envelopes has been registered, that setting is automatically selected (other

settings become unavailable) on the screen. In this case, modify the items as necessary.

3 Press [OK].

% Press [Change Set] to display the Change IndividualSet Screen. [Envelope] is automatically selected

for Paper Type (other types are unavailable) on the screen.

4 Press [Paper Size].

% Enter the width and length of the envelopes. Press [(1)], then enter the width (size in crosswise di-

rection) of the envelopes loaded in the tray. Similarly, press [(2)] and enter the length (size in feeding
direction) of the envelopes.

AccurioPress C3080/C3080P/C3070, AccurioPrint C3070L 4-10

4.2 Copy Operation

4

5 Press [Weight] and select [62-74 g/m2], [75-80 g/m2], [81-91 g/m2], or [92-105 g/m2] as required.

% Make other paper settings as necessary. When all the setting is completed, press [OK] to return to

the Machine Screen.

6 Place the original on the original glass or ADF.

7 Press the [COPY] tab to display the Copy Screen.

AccurioPress C3080/C3080P/C3070, AccurioPrint C3070L 4-11

4.2 Copy Operation

4

8 Select the tray.

% When you install Multi Bypass Tray MB-506, select [Bypass].
% When you install Paper Feeder Unit PF-707m, select [Tray5].
% When you install Large Capacity Unit LU-202m/LU-202XL/LU-202XLm, select [Tray3].

9 Choose the Simplex/Duplex setting.

% When placing the original on the original glass, select [1->1].
% When placing the original on ADF, select [1->1] if the original is one-sided or select [2->1] if it is two-

sided.

AccurioPress C3080/C3080P/C3070, AccurioPrint C3070L 4-12

4.2 Copy Operation

4

10 Select [Face Up] for Face and [1 to N] for Order in the Output Setting.

% The items automatically set for Face/Order vary depending on whether the original is placed on the

original glass or ADF. In either case, select [Face Up] for Face and [1 to N] for Order.

Press [OK] on the Output Setting Screen to return to the Copy Screen.

11 Make other copy settings as necessary.

% If the size of the original is custom, make the custom size setting in the Original Setting. For details

on the setting, refer to the HTML user's guide.

12 Press Start on the. control panel.

AccurioPress C3080/C3080P/C3070, AccurioPrint C3070L 4-13

4.3 Print Operation

4

4.3 Print Operation

The operation varies depending on the type of your printer driver. Follow the appropriate procedure to per­form your print operation.

For PS Plug-in Driver

1 Select the Print command of your application, then select the appropriate printer driver.

2 Click [Detail Setting], [Properties] or [Setting].

The Printing Preferences window of the printer driver is displayed.

3 Click the [Paper] tab.

4 Click [Acquire Tray and Paper Data] to obtain the paper information from the machine.

5 Select the paper feed tray.

% When you install Multi Bypass Tray MB-506, select [Bypass].
% When you install Paper Feeder Unit PF-707m, select [Tray5].
% When you install Large Capacity Unit LU-202m/LU-202XL/LU-202XLm, select [Tray3].

6 Click the [Layout] tab.

7 Click [Custom Size...] for the paper size and enter the size of the envelope.

% Provide all the necessary information, and then click [OK].
% For details of the envelope size, see Section 5 "Specifications.”

8 Click [OK] at the bottom of the window to start printing.

AccurioPress C3080/C3080P/C3070, AccurioPrint C3070L 4-14

4.3 Print Operation

4

For PPD Driver

1 Select the Print command of your application, then select the appropriate printer driver.

2 Click [Detail Setting] or [Properties].

The Printing Preferences window of the printer driver is displayed.

3 Click the [Paper/Quality] tab, then select [Paper Source].

% When you install Multi Bypass Tray MB-506, select [Bypass].
% When you install Paper Feeder Unit PF-707m, select [Tray5]
% When you install Large Capacity Unit LU-202m/LU-202XL/LU-202XLm, select [Tray3].

4 Select [Envelope] for "Media.”

5 Click [Advanced...] at the lower right corner of the window.

The Advanced Options window is displayed.

6 Select [PostScript Custom Page Size] for "Paper Size," and then enter the size of the envelope.

% Provide all the necessary information, and then click [OK].
% For details of the envelope size, see Section 5 "Specifications.”

7 Select [1-Sided] for "Print Type".

8 Select [Face Up] for [Output Order].

9 Click [OK] at the bottom of the Advanced Options window.

10 Click [OK] at the bottom of the Printing Preferences window to start printing.

5

Specifications

AccurioPress C3080/C3080P/C3070, AccurioPrint C3070L 5-2

5.1 Specifications of Fusing Unit EF-103

5

5 Specifications

5.1 Specifications of Fusing Unit EF-103

Name EF-103

Type Fusing unit exclusively used for printing on envelopes (with feeding auxiliary

parts)

Feeding reference point Center

Paper weight 70 to 100 g/m

2

(19 to 27 lb Bond)

Envelope sizes • Available dimensions

Width (crosswise direction): 100 to 245 mm (3.92" to 9.63")
Auxiliary guide available range: 100 to 140 mm (3.92” to 5.50”) (when Paper
Feeder Unit PF-707m is installed)
Length (feeding direction): 148 to 375 mm (5.82" to 14.73")

• Recommended sizes

N4 is supported only when the Large Capacity Unit LU-202m/LU-202XL/LU­202XLm is installed.

• Paper sizes that can be fed

• Unsuitable envelopes
Envelopes with a film window
Envelopes with a double-stick tape or release coated paper on the flap

* : About N4 envelopes (envelopes with a vertical size of less than 100 mm)

• Printing misalignment may occur as a result of offset.

• The number of envelopes loaded for ejection is not guaranteed.

North American
standard

6" x 9 - 1/2"

ISO standard

C5

Japanese standard

C6/C5

Size Width (mm) Height (mm)

K2

N3

N4*

241 152

229

229

162

114

240 332

120 235

90 205

Size Width (mm) Height (mm)

Japanese standard

K0

K1

287 382

270 382

AccurioPress C3080/C3080P/C3070, AccurioPrint C3070L 5-3

5.1 Specifications of Fusing Unit EF-103

5

Printing speed • When AccurioPress C3080/C3080P is used

North American standard
6" x 9-1/2": 70 sheets per minute
Standards other than the above
C5: 66 sheets per minute
Japanese standard
K2: 47 sheets per minute
N3: 65 sheets per minute

• When AccurioPress C3070/AccurioPrint C3070L is used
North American standard
6" x 9-1/2": 65 sheets per minute
Standards other than the above
C5: 57 sheets per minute
Japanese standard
K2: 41 sheets per minute
N3: 55 sheets per minute

* It may vary depending on paper types.

Tray capacity Paper tray: 100 sheets (6" x 9-1/2", C5, C6/C5, K2, N3, N4)

50 sheets (K0, K1)
Output tray: Approx. 50 sheets* (Output Tray OT-511)
For other output options, please contact your service representative.
* The N4 envelope is supported only when the Large Capacity Unit LU­202m/LU-202XL/LU-202XLm is installed.

Dimensions 200 (W) e 690 (D) e 235 (H) mm

(Fusing unit: excluding projection portions)

Weight 18.8 kg

Power source 208-240VAC or 220-240VAC, 5 V/24 VDC (supplied from the main body)

Power consumption 2,430 W

http://konicaminolta.com

2018.1 A9VE-EF-E-00

© 2018