Kohler K-77123T, K-77125T Installation Instructions Manual

Page 1
-1-
JUTE
INSTALLATION INSTRUCTIONS
CABINET
K-77123T/K-77125T
BEFORE YOU BEGINBEFORE YOU BEGIN
·
·
·
·
·
·
·
Turn off the water supply. The pluming installation must comply with Water Supply Regulations/Bye-laws, Building Regulations or any particular regulations and practices, specified by the local water company or water undertakers. The installation should be carried out by a plumber. Before installation carefully inspect the new fixture for any signs of damage.
please leave instructions for the
consumer.
JUTE bathroom cabinet adopts E1 grade natural black walnut wood-based panel of high quality. With further processing, its harmful emission is less than 1.5mg/L.
· This product complies with GB 24977-2010.
·
·
·
·
·
·
·
-
E1
1.5mg/L
· GB 24977-2010
ORDERING INFORMATION
This installation covers the following products in the JUTE range:
JUTE Cabinet 914mm........................................K-77125T
JUTE Cabinet 1220mm......................................K-77123T
914mm.............................................K-77125T
1220mm...........................................K-77123T
SAFETY WARNINGS
Kohler products are precision-engineered and should give continued superior and safe performance, provided:
1. They are installed, commissioned, operated and maintained in accordance with the recommendations given in this Manual.
2. Periodic attention is given, as necessary, to maintain the product in good functional order. Recommended guidelines are given in the section.
Carefully inspect the new fixture for any signs of damage.
When installing Kohler Products, manufacturers guidelines for power tool safety should be followed.
MAINTENANCE
1.
2.
KOHLER CHINA INVESTMENT CO., LTD NO.158, JIANG CHANG SAN ROAD,
ZHABEI DISTRICT, SHANGHAI, PRC POST CODE: 200436
( ) 158 200436
©©Copyright Kohler China Investment Co., Ltd. 2016
2016
1282794-T01-A
Page 2
-2-
ROUGHING-IN
UNIT : mm
K-77125T
Cabinet 914mm
914mm
K-77123T
Cabinet 1220mm
1220mm
INSTALLATION
A. Install Washbasin Cabinet
Install the services. Hot (H) and Cold (C) inlets must be connected to the correct inlet pipes. Install the drain in accordance with the manufacturer's instructions. We suggest using P-trap drain. Connect P-trap pipe with washbasin drain.
Make sure a watertight seal exisits on all
washbasin drain connections.
Provide access to the plumbing
connections for future plumbing maintenance.
The hot and cold water supplies must be installed
with isolating valves.
CAUTION !
CAUTION !
NOTE
A.
(H) (C)
P
Fig.2
2
Reference Value
Kohler reserves the right to change marked dimensions without prior notice.
Fig.1
1
914
1220
556
556
495
495
1282794-T01-A
Page 3
Fig.3
3
1. 3
I ( K-77104T-B07)
1. Place the cabinet on the floor. Fix adjustable feet as shown in Fig.3. (Put carton or foam on the floor first to prevent scratching the cabinet.)
I Installation with adjustable feet (K-77104T-B07 is not
supplied with cabinet and shall be purchased.)
2. Put the cabinet upright and place it at a desired position in the bathroom. Adjust the adjustable feet to make the cabinet level, as shown in Fig.4.
2. 4
Fig.4
4
3. Pre-drill wall anchors Adjust cabinet level and use pencil to mark the hole of the back bar on the wall. Remove the cabinet, drill 8mm & 50mm deep holes at the marked positions. Hammer the anchors into the drilled holes. Finish the step.
·
·
·
·
3.
8mm
50mm
·
·
·
·
-3-
Go Up Go Down
Horizontal
1282794-T01-A
Page 4
1. 8mm 50mm
2. ( 6)
II ( )
1. Mark the positions of the wall hangers on the wall according to the dimensions shown. Drill 8mm & 50mm deep holes and hammer the anchors in. Fix the wll hangers onto wall with screws supplied.
2. Hang the cabinet onto wall and adjust the hanger to make the cabinet level,as shown in Fig.6.
II Hang onto wall (installation without adjustable feet)
Fig.5
5
Fig.6
6
Cabinet Outline
Cabinet Outline
Wall Bracket
Wall Bracket
380
380
766
766
495
495
20
914
Centre
Centre
20
1220
3. Pre-drill wall anchors Adjust cabinet level and use pencil to mark the hole of the back bar on the wall. Remove the cabinet, drill 8mm & 50mm deep holes at the marked positions. Hammer the anchors into the drilled holes. Finish the step.
·
·
·
·
3.
8mm
50mm
·
·
·
·
-4-
B.
1.
B. Fix the cabinet onto wall
Note: For installation with or without adjustable feet,
the cabinet must be fixed onto wall with anchors.
1. Adjust the cabinet level after installation with or without adjustable feet. Fix the cabinet onto wall through the holes on the back bar with anchors and gaskets supplied.
1282794-T01-A
Page 5
C. /
//
C. Install the Synthetic Top/Counter Top
Note: Please refer to the installation instructions of synthetic
top/counter top for its installation. To protect the cabinet from dampness, please apply silicone sealant where the synthetic top and the cabinet connect.
/counter top
2. S
U
2. Floor drainage (S-Trap) Please install the drain assembly and faucet as shown. Please set the water supply and drainage position according to the suppliers instructions. You can put the
pipe into the U notch.
Fig.8
8
Faucet
Supply Lines
Shut-off Valve
Drain Assembly
Ripple Pipe
Outlet
Fig.7
7
1. (P )
/
UU
Connect Drainage
1. Inwall drainage (P-Trap) Please install the drain assembly and faucet as shown. Please set the water supply and drainage position according to the suppliers instructions. You can put the
pipe into the U notch.
Faucet
Supply Lines
Shut-off Valve
Drain Assembly
-5-
1282794-T01-A
Page 6
-6-
2.
2. Place the hinge cover and plastic cover.
Fig.9
9
D.
1. 9
D. Adjustments
1. Adjust the hinge cover in 3 direction to make sure the door is level. As shown in Fig.9.
1.
2.
3.
4.
5.
6.
7.
USER MAINTENANCEUSER MAINTENANCE
Warning! Risk of product damage.
1.
2.
3.
4.
5.
6. Please do not sit, lean or step on the basin cabinet.
7. If any fixtures caused by abnormal reasons, Kohler China can supply paid replacement for service parts caused by abnormal reasons as shown in the Service Parts Page in the limited duration of warranty.
Many cleansers contain abrasive and chemical substance which is not suitable for cleaning stainless steel, enamel, plating or plastic products. You may use mild cleansers or soaps to clean the surfaces. Wipe any splashes of cleaner solutions from the surface with clean soft cloth.
Maintain ventilation in the bathroom, and separate the dry area from the damp one if conditions permit. Try to open the door and windows of the bathroom and maintain good ventilation.
Kohler bathroom cabinet are dealt with strict procedures for damp-proof, whose good damp-proof function ensures good performance even in bathroom of huge humidity. Yet do not splash and pour water directly on the bathroom cabinet. Make sure that the bathroom is not over damp and wipe any splashes from surfaces immediately.
Maintenance of door board: Clean and wipe door board regularly, and wipe the condensation vapor with dry and soft cloth.
Ensure that electrical connections for appliances such as head lamp is insulated wipe mirror surface with chamois regularly to guarantee the persistent excellent performance.
1282794-T01-A
Loading...