KOHLER K-3099, K-3146, K-3147, K-3148, K-3150 User Manual
...
Installation Guide
Undercounter Stainless Steel Sinks
K-3099, K-3146, K-3147,
K-3148, K-3150, K-3163,
K-3164, K-3165, K-3166,
K-3168, K-3171, K-3174,
K-3177, K-3180, K-3181,
K-3182, K-3183, K-3184,
K-3185, K-3186, K-3197,
K-3325, K-3330, K-3331,
K-3332, K-3333, K-3334,
K-3335, K-3336, K-3337,
K-3338, K-3339, K-3340,
K-3341, K-3343, K-3345,
K-3350, K-3351, K-3352,
K-3353, K-3354, K-3355,
K-3356, K-3359, K-3376
M product numbers are for Mexico (i.e. K-12345M)
Los números de productos seguidos de
M corresponden a México (Ej.
K-12345M)
Français, page “Français-1”
Español, página “Español-1”
1019948-2-D
Tools and Materials
Safety
Glasses
Drill
Tape
Measure
Pencil
Sealant
Template
(supplied)
Scissors
Hacksaw
Plus:
• 1/2" or larger drill bit
• Hole saw 1-3/8"
• Gloves
• Jigsaw
Thank You For Choosing Kohler Company
We appreciate your commitment to Kohler quality. Please take a few
minutes to review this manual before you start installation. If you
encounter any installation or performance problems, please don’t
hesitate to contact us. Our phone numbers and website are listed on
the back cover. Thanks again for choosing Kohler Company.
Before You Begin
WARNING: Risk of personal injury. Metal surfaces are sharp
and can cause severe cuts. Use gloves and handle sink edges
carefully.
Observe all local plumbing and building codes.
Prior to installation, unpack the new sink and inspect it for
damage. Return the sink to its protective carton until you are
ready to install it.
Inspect the drain and supply tubing. Replace if necessary.
Due to the nature of undercounter installations, Kohler Co.
recommends that undercounter sink installations be performed by
trained and experienced installers.
Install so future removal from underneath the countertop is
possible without damaging the countertop.
For multiple bowl installations, a minimum distance of 2-3/16″
(5.6 cm) is required between the bowls. Any required support
should be determined by the countertop supplier.
1019948-2-D 2 Kohler Co.
Countertop
Mounting
Bracket
Fastener (Not Furnished)
No Reveal Mounting
Mounting
Bracket
Fastener (Not
Furnished)
Reveal Mounting
Sealant (Not
Furnished)
Sink
Countertop
Sealant (Not
Furnished)
Sink
C
L of the Faucet
"X"
See centerline
table.
Template
Cutting Line
1. Preparation
Install the water supplies and drain piping according to the
roughing-in information.
NOTE: You may require different, more specialized tools to install
this sink to countertop materials other than wood or wood
composites.
NOTE: For multiple bowl installations of single basin sinks, a
minimum distance of 2-3/16″ (5.6 cm) is required between bowls.
Any required support should be determined by the countertop
supplier.
Cut along the inside of the template line where indicated for the
countertop opening.
Position the template on the countertop. Check for adequate
clearance between the sink, faucet, backsplash and cabinet.
Trace around the template on the countertop with a pencil.
Centerlines are provided to help align the opening.
Locate the faucet hole centerlines on the countertop. Faucet
centerline clearance from the top of the cut-out must be 2-3/8″ (6
cm) minimum for a No-Reveal sink and 1-3/4″ (4.4 cm) minimum
for a Reveal sink.
Kohler Co. 3 1019948-2-D
2. Faucet Centerline Table
Value for ″X″
(inches)
Model Reveal
Cutout
K-3325 N/A 2-3/8″
K-3330 N/A 2-3/8″
K-3331 N/A 2-3/8″
K-3332 N/A 2-3/8″
K-3333 N/A 2-3/8″
K-3334 N/A 2-3/8″
K-3335 N/A 2-3/8″
K-3336 N/A 2-3/8″
K-3337 N/A 2-3/8″
K-3338 N/A 2-3/8″
K-3339 N/A 2-3/8″
K-3340 N/A 2-3/8″
K-3341 N/A 2-3/8″
K-3350 1-5/8″
(4.1 cm)
K-3351 1-5/8″
(4.1 cm)
K-3352 1-5/8″
(4.1 cm)
K-3353 1-5/8″
(4.1 cm)
K-3354 1-5/8″
(4.1 cm)
K-3355 1-5/8″
(4.1 cm)
NoReveal
Cutout
(6 cm)
(6 cm)
(6 cm)
(6 cm)
(6 cm)
(6 cm)
(6 cm)
(6 cm)
(6 cm)
(6 cm)
(6 cm)
(6 cm)
(6 cm)
2-3/8″
(6 cm)
2-3/8″
(6 cm)
2-3/8″
(6 cm)
2-3/8″
(6 cm)
2-3/8″
(6 cm)
2-3/8″
(6 cm)
Notes
Measure from smaller basin
Measure from smaller basin
Measure from smaller basin
1019948-2-D 4 Kohler Co.
Faucet Centerline Table (cont.)
Value for ″X″
(inches)
Model Reveal
Cutout
NoReveal
Notes
Cutout
K-3356 1-5/8″
(4.1 cm)
K-3180 1-5/8″
(4.1 cm)
K-3181 1-5/8″
(4.1 cm)
K-3182 1-5/8″
(4.1 cm)
K-3183 1-5/8″
(4.1 cm)
K-3184 1-5/8″
(4.1 cm)
K-3376 1-5/8″
(4.1 cm)
2-3/8″
(6 cm)
2-3/8″
(6 cm)
2-3/8″
(6 cm)
2-3/8″
(6 cm)
2-3/8″
(6 cm)
2-3/8″
(6 cm)
2-3/8″
(6 cm)
Measure from smaller basin
Measure from smaller basin
K-3146 N/A N/A Faucet hole location shown on
cutout template
K-3147 N/A N/A Faucet hole location shown on
cutout template
K-3185 N/A N/A Faucet hole location shown on
cutout template
K-3186 N/A N/A Faucet hole location shown on
cutout template
K-3148 N/A N/A Faucet hole location shown on
cutout template
K-3197 N/A N/A Faucet hole location shown on
cutout template
K-3099 N/A N/A Faucet hole location shown on
cutout template
K-3099-L N/A N/A Faucet hole location shown on
cutout template
K-3359 N/A N/A Faucet hole location shown on
cutout template
K-3359-L N/A N/A Faucet hole location shown on
cutout template
K-3163 N/A 2-3/8″
(6 cm)
Kohler Co. 5 1019948-2-D
Faucet Centerline Table (cont.)
Value for ″X″
(inches)
Model Reveal
Cutout
K-3164 N/A 2-3/8″
K-3351-L 1-5/8″
(4.1 cm)
K-3171 1-5/8″
(4.1 cm)
K-3174 1-5/8″
(4.1 cm)
K-3174-L 1-5/8″
(4.1 cm)
K-3352-L 1-5/8″
(4.1 cm)
K-3177 1-5/8″
(4.1 cm)
K-3353-L 1-5/8″
(4.1 cm)
K-3177-L 1-5/8″
(4.1 cm)
K-3150 1-5/8″
(4.1 cm)
K-3354-L 1-5/8″
(4.1 cm)
K-3150-L 1-5/8″
(4.1 cm)
K-3355-L 1-5/8″
(4.1 cm)
K-3356-L 1-5/8″
(4.1 cm)
K-3165 1-5/8″
(4.1 cm)
K-3166 1-5/8″
(4.1 cm)
K-3166-L 1-5/8″
(4.1 cm)
K-3168 1-5/8″
(4.1 cm)
NoReveal
Cutout
(6 cm)
2-3/8″
(6 cm)
2-3/8″
(6 cm)
2-3/8″
(6 cm)
2-3/8″
(6 cm)
2-3/8″
(6 cm)
2-3/8″
(6 cm)
2-3/8″
(6 cm)
2-3/8″
(6 cm)
2-3/8″
(6 cm)
2-3/8″
(6 cm)
2-3/8″
(6 cm)
2-3/8″
(6 cm)
2-3/8″
(6 cm)
2-3/8″
(6 cm)
2-3/8″
(6 cm)
2-3/8″
(6 cm)
2-3/8″
(6 cm)
Notes
Measure from smaller basin
Measure from smaller basin
Measure from smaller basin
Measure from smaller basin
Measure from smaller basin
Measure from smaller basin
Measure from smaller basin
Measure from smaller basin
Measure from smaller basin
Measure from smaller basin
Measure from smaller basin
1019948-2-D 6 Kohler Co.
Faucet Centerline Table (cont.)
Value for ″X″
(inches)
Model Reveal
Cutout
K-3168-L 1-5/8″
(4.1 cm)
NoReveal
Cutout
2-3/8″
(6 cm)
Notes
Kohler Co. 7 1019948-2-D
Insert (Not Furnished)
Countertop Opening - Bottom View
Mounting
Bracket
Fastener (Not Furnished)
1-3/8" (3.5 cm)
Turn the brackets so they
fit over the sink rim.
Sink - Bottom View
3. Install the Sink
WARNING: Risk of personal injury. Metal surfaces are sharp
and can cause severe cuts. Use gloves and handle sink edges
carefully.
CAUTION: Risk of product damage. Do not cut, drill, or sand
the countertop while it is positioned over the fixture.
Cut out the opening by carefully following the pencil line traced
from the template.
For laminate-type countertops, make sure all exposed
non-laminated surfaces located near the cut-out area are finished
and sealed to prevent damage from water absorption.
Drill the required faucet holes and install the faucet to the
countertop according to the manufacturer’s instructions.
Equally space the required number of mounting brackets and
locate the mounting holes on the underside of the countertop
(find model number below for required number of brackets).
•
Requires four mounting brackets: K-3339.
•
Requires eight mounting brackets: K-3146, K-3147, K-3164,
K-3184, K-3331, K-3333, K-3336, K-3337, K-3338, K-3343, and
K-3345.
•
Requires 10 mounting brackets: K-3182, K-3186, K-3163, and
K-3334.
•
Requires 12 mounting brackets: K-3325, K-3332, K-3335, and
K-3340.
Edge
Countertop
Opening
1019948-2-D 8 Kohler Co.
Install the Sink (cont.)
•
Requires 16 mounting brackets: K-3099, K-3099-L, K-3148,
K-3150, K-3150-L, K-3165, K-3166, K-3166-L, K-3168, K-3168-L,
K-3171, K-3174, K-3174-L, K-3177, K-3177-L, K-3180, K-3181,
K-3183, K-3185, K-3197, K-3350, K-3351, K-3351-L, K-3352,
K-3352-L, K-3353, K-3353-L, K-3354, K-3354-L, K-3355, K-3355-L,
K-3356, K-3356-L, K-3359 K-3359-L and K-3376.
•
The type of fastener is dependent upon the countertop material
and should be recommended by a countertop supplier.
Turn the clamps parallel to the opening to allow for easy
installation of the sink.
Clean all residue from the top of the sink rim. Clean the
underside of the countertop around the cut-out area, making sure
the surface is smooth and free of defects.
Apply a generous bead of silicone or latex sealant to the rim of
the sink, near the inside edge.
Position and align the sink with the opening in the countertop.
Rotate the mounting brackets over the sink rim and tighten until
snug.
Check the alignment of the sink with the cut-out and tighten the
fasteners.
Optional: Apply a bead of high-quality sealant between the
countertop and the top of the sink rim.
Immediately wipe away any excess sealant, and fill any voids as
needed.
Allow the sealant to cure for at least 30 minutes before
proceeding.
Install the garbage disposal, if desired. Follow the manufacturer’s
instructions.
Connect and tighten the trap to the strainer, and complete the
water supply connections to the faucet according to the
instructions packed with the faucet.
Run water into the sink and check for leaks.
Clean up with a non-abrasive cleaner.
Kohler Co. 9 1019948-2-D
Loading...