KOHLER K-3180, K-3181, K-3182, K-3183, K-3184 User Manual
...
Installation Guide
Stainless Steel Undercounter
Kitchen and Bar Sinks
K-3180, K-3181, K-3182, K-3182,
K-3183, K-3184, K-3330, K-3331,
K-3332, K-3333, K-3334, K-3335,
K-3336, K-3337, K-3338, K-3339,
K-3340, K-3343, K-3345, K-3350,
K-3351, K-3352, K-3353, K-3354,
K-3355, K-3356, K-3376, K-14300,
K-14301
Français, Page 8
Español, Página 14
1007258-2-C
1007258-2-C
Tools and Materials
Pencil and
Marker
Sealant
Measuring Tape
Safety Glasses
Drill
Keyhole/Compass
or Saber Saw
Scissors
Putty Knife
Thank You For Choosing Kohler Company
We appreciate your commitment to Kohler quality. Please take a few
minutes to review this manual before you start installation. If you
encounter any installation or performance problems, please don’t
hesitate to contact us. Our phone numbers and website are listed on
the back cover. Thanks again for choosing Kohler Company.
Before You Begin
- Refer to the Homeowners Guide to determine all necessary
components for your installation.
- Remove the sink from its carton and inspect it for damage.
- During installation, store the sink in the protective carton whenever
possible.
- Observe all local plumbing and building codes.
1007258-2-C
2
Kohler Co.
(B)
(B)
(A)
(B)
(B)
(A)
(B)
(A)
(A)
(A)
SINGLE BASIN SINK - OVERALL DIMENSIONS
Model (A) (B) Depth (C) No. of
Brackets
K-3182 16-1/4” (41.3cm) 20-1/2” (52.1cm) 7-1/2” (19cm) 10
K-3183 31-5/8” (80.3cm) 17-3/4” (45.1cm) 7-1/2” (19cm) 16
K-3184 18-5/8” (47.3cm) 17-1/2” (44.5cm) 7-1/2” (19cm) 8
K-3330 15-3/4” (40cm) 17-1/2” (44.5cm) 9-1/2” (24cm) 8
K-3331 15-3/4” (40cm) 17-1/2” (44.5cm) 7-1/2” (19cm) 8
K-3332 23” (58.4cm) 17-1/2” (44.5cm) 7-1/2” (19cm) 12
K-3333 10-3/4” (27.3cm) 17-1/2” (44.5cm) 5-1/2” (14cm) 8
K-3334 15-3/4” (40cm) 20-3/8” (51.8cm) 7-1/2” (19cm) 10
K-3335 19-5/8” (49.8cm) 19-5/8” (49.8cm) 9-1/2” (24cm 12
K-3336 15-1/2” (39.4cm) 17-1/8” (43.5cm) 7-1/2” (19cm) 8
K-3337 15-1/2” (39.4cm) 19-5/8” (49.8cm) 7-1/2” (19cm) 8
K-3338 11” (28cm) 17-1/8” (43.5cm) 5-1/2” (14cm) 8
K-3339 13-5/8” (34.6cm) 5-1/4” (13.3cm) 4
K-3340 23” (58.4cm) 17-1/2” (44.5cm) 2” (5cm) 12
K-3343 17-1/2” (44.5cm) 5-3/8” (13.7cm) 7-1/2” (19cm) 8
K-3345 17-1/2” (44.5cm) 11-1/4” (28.6cm) 7-1/2” (19cm) 8
K-3376 35-1/2” (90.2cm) 18-1/2” (47cm) 10” (25.4cm) 16
K-14300 15-1/2” (39.4cm) 17-1/8” (43.5cm) 7-1/2” (19cm) 8
K-14301 13-5/8” (34.6cm) 5-1/4” (13.3cm) 4
1. Roughing-In Dimensions
Kohler Co.
3
1007258-2-C
LEFT BASIN
RIGHT BASIN
(B)
(C)
(A)
DOUBLE BASIN SINK - OVERALL DIMENSIONS
Model (A) (B) (C) No. of
Brackets
K-3150 31-1/2” (80cm) 18” (45.7cm) 16
K-3180 31-1/2” (80cm) 17-3/4” (45.1cm) 16
K-3181 31-1/2” (80cm) 21-1/2” (54.6cm) 17-3/4” (45.1cm) 16
K-3351 31-1/2” (80cm) 18” (45.7cm) 16
K-3352 31-1/2” (80cm) 18” (45.7cm) 16
K-3353 31-1/2” (80cm) 20-7/8” (53cm) 18” (45.7cm) 16
K-3354 31” (78.7cm) 20-1/8” (51cm) 17-5/8” (44cm) 16
K-3355 30-3/4” (78cm) 20-1/8” (51cm) 17-5/8” (44cm) 16
K-3356 35-1/8” (89.2cm) 20-1/8” (51cm) 17-5/8” (44cm) 16
Roughing-In Dimensions (continued)
1007258-2-C
4
Kohler Co.
Faucet
Centerline
2-3/8”
(6cm) MIN.
Cutting Line
1. Position the Template
- Cut the template following the lines marked “Cut on this line”.
- Determine your desired installation location. Use the center lines
provided on the template to assist in positioning.
- Position the template on the countertop in the desired location. Make
sure the template is secured firmly in place so i t cannot move.
- Check for adequate clearance between the sink, faucet and
backsplash. Verify that the sink will not interfere with the cabinet
during installation.
- Tracetheoutsideedgesofthetemplatewithapencil.
: For multiple sink installations, a minimum distance of 2-3/16”
NOTE
(7.1cm) is required between the sinks.
- Locate the faucet hole center lines on the countertop. The faucet hole
clearance from the top of the cutout must be 2-3/8” (6cm) minimum.
2. Cut the Sink Mounting Holes
CAUTION: Risk of product damage. To avoid damage to the sink,
do not cut , drill, or sand the countertop while it is positioned over
the sink.
- Beforecutting,measurethecut-outlineandcompareittothe
overall sink dimension. The cut-out should be 1-1/2” (3.8cm)
smaller than the overall sink dimensions.
- Drill a pilot hole inside the cut-out line.
- Using a saber or keyhole saw, cut along the inside of the cut-out line.
- Drill the required faucet holes and install the faucet to the
countertop according to the faucet manufacturer’s instructions.
Kohler Co.
5
1007258-2-C
Insert (Not Furnished)
Edge
Countertop
Opening
Countertop Opening —
Bottom View
Mounting
Bracket
Fastener
(Not Furnished)
1-3/8” (3.5cm)
± 1/4” (6mm)
3. Install the Mounting Brackets
- Forlaminatetypecountertops,makesurethatallexposed
non-laminated surfaces located near the cut-out area are finished
and s ealed in order to prevent damage from water absorption.
- Equally space the required number of mounting brackets (see chart
on roughing-in page) and locate the mounting holes on the
underside of the countertop 1-3/8” (3.5cm) from the edge of the
countertop opening.
- The type of fastener needed is dependant upon the countertop
material and should be recommended by the countertop supplier.
- Loosely install the mounting brackets to the countertop.
- Turn the brackets parallel to the opening to allow for easy
installation of the sink.
1007258-2-C
6
Kohler Co.
Loading...