Quick start
1
Charge until the
light stops blinking.
2
Insert an accessory
SD or SDHC card.
3
Set language, date/time.
OK
On
4
Take videos, pictures.
5
Install software, then share.
Record
Keep learning!
Take and share your
best videos, pictures!
ENGLISH
www.kodak.com/go/support 1
ENGLISH
Lens
Microphone
Front view
2 www.kodak.com/go/support
Back view
Settings button
Delete button
Record/OK
Review button
On bottom:
• Speaker
• Tripod socket
• Infrared receiver
HDMI™ Out
Record mode
button
Slot for accessory
SD/SDHC Card
Share button
(for optional remote control)
ENGLISH
www.kodak.com/go/support 3
ENGLISH
Door to 5V-In, A/V,
Camera Reset button
Battery Charging light
Power button
Camera Reset button
Side view
4 www.kodak.com/go/support
Opening the USB arm
1
2
Pull the USB
arm to the
left.
To close the USB arm,
reverse these steps.
Pull the USB
release to
the right and
down.
NOTE: The USB
arm is fairly
flexible.
ENGLISH
www.kodak.com/go/support 5
ENGLISH
V
i
d
e
o
/
p
i
c
t
u
r
e
n
u
mb
e
r
R
e
c
o
r
d
i
n
g
V
i
d
e
o
l
e
n
g
t
h
R
e
c
o
r
d
i
n
g
Z
o
o
m
E
l
a
p
s
e
d
t
i
m
e
V
o
l
u
m
e
P
l
a
y
b
a
c
k
Understanding the status icons
6 www.kodak.com/go/support
Charging the battery
(approx. 3–3.5 hours)
Charging light:
• Blinking = charging
• Steady On = charged
KODAK Camera USB Cable, Micro B / 5-Pin
(Use only the cable included with this camera.)
Yours may differ.
Use this procedure to charge the battery or power the camera
with AC power. Charge the battery as often as you like—you
can’t over-charge—but always fully charge before using.
IMPORTANT:
The battery is not removable.
ENGLISH
See the Extended user guide www.kodak.com/go/Ze1manuals
www.kodak.com/go/support 7
ENGLISH
(approx. 4.5 hours)
Charging light:
• Blinking = charging
• Steady On = charged
It may be convenient to use a
USB extension cable to connect
the camera to the computer.
NOTE: The camera charges
when the computer is on and
awake. Turn off your
computer’s hibernation,
sleep, and standby modes.
Charging using USB
Open the USB arm page 5
8 www.kodak.com/go/support
Inserting an accessory SD or SDHC Card
CAUTION:
1
Turn off the camera.
2
Insert the card until it clicks.
Accessory
To remove the card, press and
release it, then pull it out.
Your camera has enough internal memory for a practice video/picture.
IMPORTANT:
features—including social networking and email—you must
purchase and insert a card (SDHC Class 4 or higher; maximum
supported size: 32 GB).
A card can only be inserted one way; forcing it may cause damage.
Inserting or removing a card while the camera is on may damage the
video/pictures, the card, or the camera.
When you turn on the camera, it checks to see if a card is inserted. If so,
new pictures/videos are stored on the card. If no card is inserted, new
pictures/videos are stored in the camera’s internal memory. If pictures/videos
are detected in internal memory and a card is inserted, the camera prompts
you to move the pictures to the card (and erase those in internal memory).
For the best experience and to use the sharing
ENGLISH
Purchase accessories www.kodak.com/go/accessories
www.kodak.com/go/support 9
ENGLISH
Connecting the strap
See the Extended user guide www.kodak.com/go/Ze1manuals
10 www.kodak.com/go/support
Turning on the camera
to change current field.
for previous/next field.
OK
to accept.
At the prompt, press
OK
.
Date/Time
Language
to change.
OK
to accept.
Setting the date/time
See the Extended user guide www.kodak.com/go/Ze1manuals
www.kodak.com/go/support 11
ENGLISH
ENGLISH
When you turn on the camera, it’s
ready to record.
Zoom in/out.
Start/stop recording.
Turn on the Glare Shield (if
enabled in the Settings menu) to
improve LCD viewability.
In Review or in a menu, press to
recording modes (video/pictures).
In Liveview, press to change
go to Liveview.
Recording videos, taking pictures
IMPORTANT:
For the best experience and to use the sharing
features—including social networking and email—you must
purchase and insert a card (SDHC Class 4 or higher; maximum
supported size: 32 GB).
Recording modes
1080p
best for
viewing
on an
HDTV
720/
60 fps
best for
sports and
action
720p
best for viewing on a
computer, sharing on
YouTube and
FACEBOOK
WVGA (iPad
Compatible)
best for
conserving
memory card
space
Still
for
pictures
See the Extended user guide www.kodak.com/go/Ze1manuals
12 www.kodak.com/go/support
Accessing the settings menu
P
r
e
s
s
t
h
e
S
e
t
t
i
n
g
s
b
u
t
t
o
n
.
ENGLISH
LCD Brightness &
Glare Shield
Effects Vivid Color, Normal Color, Sepia, B&W, High Saturation, or
Video Resolution HD 1080p, HD 720p, HD 720p 60 fps, WVGA
Microphone Gain Adjust sensitivity of the internal microphone.
Sounds & LED Turn sounds and the Video Recording light on/off.
Date/Time
Share Settings Choose which social networking sites and email addresses
Video Output Choose the setting (NTSC, PAL) for your region.
Language Choose your language.
Reset Settings Return all settings to their factory default.
Format Card Erase, format the card.
About View firmware and ARCSOFT Software versions.
When you’re reviewing a video and press the Settings button, you also get Trim
and Make Picture choices.
www.kodak.com/go/support 13
Turn on to improve LCD viewability in bright conditions. (See
more about the Glare Shield feature, page 12.)
70s Film
Set the date/time.
are offered when you share a picture/video.
ENGLISH
Review
.
Previous/next
video/picture.
Play/Pause.
(Press and hold to Stop.)
1
3
OK
2
Adjust
volume.
Delete
video/pictures.
While playing, fast-forward/fast rewind.
Playing videos
See the Extended user guide www.kodak.com/go/Ze1manuals
Use the optional remote page 19
14 www.kodak.com/go/support
Deleting videos/pictures
2
3
1
Review
.
Previous/next
video/picture.
Delete.
4
Highlight Delete or OK, then press
the OK button.
ENGLISH
See the Extended user guide www.kodak.com/go/Ze1manuals
www.kodak.com/go/support 15
ENGLISH
If this is the first time you’ve
connected to this computer, follow
the prompts to install the KODAK
Share Button App.
2
1
Connect the camera to the computer
USB port. (It turns on automatically.)
Follow the on-screen instructions to
transfer and share videos.
3
Transferring, sharing online, editing
WINDOWS OS-based computers: Install ARCSOFT
MEDIAIMPRESSION for KODAK Software to help organize and
edit videos.
MAC OS-based computers: Use the APPLE ILIFE suite of
products to edit videos/pictures and make DVDs.
Get KODAK Share Button App
support
Get ArcSoft product support www.arcsoft.com/support
See HD video system
requirements for playback on
your computer
www.kodak.com/go/camerasw
www.kodak.com/go/HDsysreq
16 www.kodak.com/go/support
Keep learning about your camera
Go to www.kodak.com/go/Ze1support for:
• the Extended user guide
• how-to videos
• camera firmware updates
• answers to your frequently asked questions
• product registration
Congratulations!
You ha v e:
• set up your camera
• taken videos
• transferred videos to your computer
Keep learning!
Finish reading this book, so you can take and share your best
pictures and videos!
See the Extended user guide www.kodak.com/go/Ze1manuals
See How-To videos www.kodak.com/go/Ze1demos
ENGLISH
www.kodak.com/go/support 17
1 Using your camera
HDMI Cable AV Cable
Viewing on a TV
If you have an HD television, use an HDMI cable—and get the
richest playback experience. (Cables may be sold separately.)
NOTE: Set your TV’s input setting to HDMI or AV.
See the Extended user guide www.kodak.com/go/Ze1manuals
Purchase accessories www.kodak.com/go/accessories
18 www.kodak.com/go/support
Using your camera
L
i
v
e
v
i
e
w
(
V
i
d
e
o
/
S
t
i
l
l
)
R
e
v
i
e
w
M
o
d
e
O
K
/
P
l
a
y
S
t
o
p
D
e
l
e
t
e
P
r
e
v
i
o
u
s
/
N
e
x
t
R
e
v
e
r
s
e
/
F
o
r
w
a
r
d
V
o
l
u
m
e
/
Z
o
o
m
F
i
r
s
t
,
r
e
m
o
v
e
t
h
e
p
u
l
l
t
a
b
.
Using the optional remote control
Use the optional remote control to review videos and pictures.
Go to www.kodak.com/go/accessories.
www.kodak.com/go/support 19
Using your camera
Using the Trim Video feature
Use the Trim Video feature to remove an unwanted video start
and/or finish, leaving only the desired portion.
1 Press the Review button, then to find a video to trim.
Optional: Play, then pause the video at the desired new start
point.
2 Press the Settings button .
3 Press to choose Trim Video, then press OK.
An instruction screen appears. After you read it, press OK.
4 When prompted, press to move the Start marker to the
new position, then press OK. Press to move the End
marker to the new position, then press OK.
NOTE: If you need to make adjustments, press to highlight the Start or
End marker, then press to move it. When finished, press OK.
5 When prompted, preview your edit or save the edits without
previewing. Save the video, or Save As if you want to keep
the existing video, as well.
20 www.kodak.com/go/support
Using your camera
Using the Make Picture feature
You can choose a single frame from a video, then make it into a
picture. (Size and quality depend on video resolution.)
1 Press the Review button, then to find a video from
which you want to extract a single video frame.
2 Play, then pause the video at the desired frame.
3 Press the Settings button .
4 Press to choose Make Picture, then press OK.
5 Follow the prompts to save the picture.
www.kodak.com/go/support 21
2 Getting help
Problem Solution
Low battery.
Can’t use the Share
features.
Can’t delete videos
and pictures from
internal memory.
Card or internal
memory is nearly
full.
Corrupt or unusable
card.
Card is full.
Unrecognized file.
Camera will not turn
off.
Camera will not turn
on.
■ Charge the battery (page 7).
■ To use the Share features (and to delete
videos and pictures after you transfer
them), video and pictures must be captured
on a card (page 9).
■ Delete videos and pictures from internal
memory while in Review mode (page 14).
■ Transfer videos/pictures to your computer
(page 16), then format (erase) the card in
the camera or card reader.
■ For the best experience, we strongly
suggest purchasing a Class 4 or higher
SDHC Card.
■ Transfer videos/pictures to your computer
(page 16) or use another card (page 9).
■ Transfer videos/pictures to your computer
(page 16).
■ Use a pin or paperclip to press the Camera
Reset button (page 4).
■ Ensure that the battery is charged (page 7).
■ Ensure the camera is clean and dry. (If it’s
wet inside, open all doors. Remove the
card. Do not turn on the camera. Let it dry
for at least 24 hours.)
22 www.kodak.com/go/support
Getting help
Problem Solution
LCD is hard to see. ■ Turn on LCD Glare Shield in the Settings
menu (page 13), then enable it in Liveview
(page 12).
Videos are choppy or
jumpy when played
on a computer.
■ Use ARCSOFT MEDIAIMPRESSION for
KODAK Software for video playback
(page 16).
■ Ensure that the computer system
requirements are met. Go to
www.arcsoft.com/support or
www.kodak.com/go/HDsysreq.
■ For the best experience, we strongly
suggest purchasing a Class 4 or higher
SDHC Card.
Videos are blurry.
■ Ensure that the lens is clean.
■ Ensure that the subject is at least 1 m
(3.3 ft) from the lens.
Videos are low
resolution.
Videos are not
saved.
Solve problems with
ARCSOFT Software.
■ If no card is inserted and the camera is
powered by the AC adapter, then videos
are taken in low resolution and are not
saved. (The camera is in Demo mode.)
Insert a card or unplug the AC adapter.
■ Go to www.arcsoft.com/support. (For other
applications, go to their support sites.)
www.kodak.com/go/support 23
Getting help
Problem Solution
Videos do not play
on a TV.
■ Ensure that an HDMI or AV Cable is
properly connected directly to the TV input
(page 18).
■ Ensure that your TV’s settings are correct
for an HDMI or AV connection.
■ Ensure that the Video Output is set
correctly.
Camera will not
work with optional
remote control.
■ Ensure that the battery is correctly inserted
in the remote control.
■ Ensure that the camera infrared receiver
(on bottom of camera) and the remote
control have an unobstructed path.
■ Try a different angle, or move closer.
Getting help on the Web
Get support for your product www.kodak.com/go/Ze1support
Download the latest camera
firmware and software
See the Extended user guide www.kodak.com/go/Ze1manuals
Chat, email, write, or phone
Kodak (Chat not available in all
languages)
Get information on ARCSOFT
Software
www.kodak.com/go/Ze1downloads
www.kodak.com/go/contact
www.arcsoft.com/support
24 www.kodak.com/go/support
3 Appendix
CAUTION:
Do not disassemble this product; there are no user-serviceable parts inside. Refer servicing to
qualified service personnel. KODAK AC Adapters and Battery Chargers are intended for
indoor use only. The use of controls, adjustments, or procedures other than those specified
herein may result in exposure to shock and/or electrical or mechanical hazards. If the LCD
breaks, do not touch the glass or liquid. Contact Kodak customer support.
■ The use of an accessory that is not recommended by Kodak may cause fire, electric
shock, or injury. For approved accessories, go to www.kodak.com/go/accessories.
■ Use only a USB-certified computer equipped with a current-limiting motherboard.
Contact your computer manufacturer if you have questions.
■ If using this product in an airplane, observe all instructions of the airline.
■ When removing the battery, allow it to cool; it may be hot.
■ Follow all warnings and instructions supplied by the battery manufacturer.
■ Use only batteries approved for this product to avoid risk of explosion.
■ Keep batteries out of the reach of children.
■ Do not allow batteries to touch metal objects, including coins. Otherwise, a battery may
short circuit, discharge energy, become hot, or leak.
■ Do not disassemble, install backward, or expose batteries to liquid, moisture, fire, or
extreme temperature.
■ Remove the battery when the product is stored for an extended period of time. In the
unlikely event that battery fluid leaks inside the product, contact Kodak customer
support.
■ In the unlikely event that battery fluid leaks onto your skin, wash immediately with
water and contact your local health provider. For additional health-related information,
contact your local Kodak customer support.
■ See www.kodak.com/go/reach for information about the presence of substances
included on the candidate list according to article 59(1) of Regulation (EC) No.
1907/2006 (REACH).
■ Dispose of batteries according to local and national regulations. Go to
www.kodak.com/go/kes.
■ Do not charge non-rechargeable batteries.
For more information on batteries, see www.kodak.com/go/batterychart.
Limited Warranty
Kodak warrants its digital cameras and accessories (excluding batteries) to be free from
www.kodak.com/go/support 25
Appendix
malfunctions and defects in both materials and workmanship for the warranty period
specified on your KODAK Product packaging. Retain the original dated sales receipt. Proof of
purchase date is required with any request for warranty repair.
Limited warranty coverage
Warranty service is only available from within the country where the products were originally
purchased. You may be required to ship products, at your expense, to the authorized service
facility for the country where the products were purchased. Kodak will repair or replace
products if they fail to function properly during the warranty period, subject to any conditions
and/or limitations stated herein. Warranty service will include all labor as well as any
necessary adjustments and/or replacement parts. If Kodak is unable to repair or replace a
product, Kodak will, at its option, refund the purchase price paid for the product provided
the product has been returned to Kodak along with proof of the purchase price paid. Repair,
replacement, or refund of the purchase price are the sole remedies under the warranty. If
replacement parts are used in making repairs, those parts may be remanufactured, or may
contain remanufactured materials. If it is necessary to replace the entire product, it may be
replaced with a remanufactured product. Remanufactured products, parts and materials are
warranted for the remaining warranty term of the original product, or 90 days after the date
of repair or replacement, whichever is longer.
Limitations
This warranty does not cover circumstances beyond Kodak’s control. This warranty does not
apply when failure is due to shipping damage, accident, alteration, modification,
unauthorized service, misuse, abuse, use with incompatible accessories or attachments (such
as third party ink or ink tanks), failure to follow Kodak’s operation, maintenance or repacking
instructions, failure to use items supplied by Kodak (such as adapters and cables), or claims
made after the duration of this warranty. Kodak makes no other express or implied
warranty for this product, and disclaims the implied warranties of
merchantability and fitness for a particular purpose. In the event that the exclusion
of any implied warranty is ineffective under the law, the duration of the implied warranty will
be one year from the purchase date or such longer period as required by law. The option of
repair, replacement, or refund is Kodak’s only obligation. Kodak will not be responsible for
any special, consequential or incidental damages resulting from the sale, purchase, or use of
this product regardless of the cause. Liability for any special, consequential or incidental
damages (including but not limited to loss of revenue or profit, downtime costs, loss of the
use of the equipment, cost of substitute equipment, facilities or services, or claims of your
customers for such damages resulting from the purchase, use, or failure of the product),
regardless of cause or for breach of any written or implied warranty is expressly disclaimed.
The limitations and exclusions of liability set forth herein apply to both Kodak and its
suppliers.
You r rig ht s
Some states or jurisdictions do not allow exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not apply to you. Some
states or jurisdictions do not allow limitations on how long an implied warranty lasts, so the
above limitation may not apply to you. This warranty gives you specific rights, and you may
have other rights which vary from state to state or by jurisdiction.
26 www.kodak.com/go/support
Appendix
N137
Outside the United States and Canada
In countries other than the United States and Canada, the terms and conditions of this
warranty may be different. Unless a specific Kodak warranty is communicated to the
purchaser in writing by a Kodak company, no warranty or liability exists beyond any
minimum requirements imposed by law, even though defect, damage, or loss may be by
negligence or other act.
FCC compliance and advisory
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. The KODAK High
Performance USB AC Adapter K20-AM complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference that may
cause undesired operation.
Canadian DOC statement
DOC Class B Compliance—This Class B digital apparatus complies with Canadian
ICES-003.
Observation des normes-Classe B—Cet appareil numérique de la classe B est conforme
à la norme NMB-003 du Canada.
China RoHS
VCCI Class B ITE
Australian C-Tick
www.kodak.com/go/support 27
Appendix
Korean Class B ITE
Korean Li-Ion Regulatory
Eastman Kodak Company
Rochester, New York 14650
© Kodak, 2011
Kodak and PlayFull are trademarks of Eastman Kodak Company.
4H7354_en
28 www.kodak.com/go/support
Loading...