Kodak KY0730485 User Manual

Matchprint
Professional Server v3.0
for Xerox DocuColor 12 Printer/Copier
Quick Start
Part number - KY0730485
Trademarks
Matchprint is a trademark of Kodak Polychrome Graphics. Kodak is a trademark of Eastman Kodak Company. Xerox and DocuColor 12 are trademarks of Xerox Corporation. Pantone and Pantone Matching System are trademarks of Pantone, Inc. All other trademarks and registered trademarks used herein are the property of their respective owners.
October 2002. Revision A, MPS v3.0
Matchprint Professional Server for DocuColor 12 Printer/Copier – Quick Start
Table of Contents
QUICK START STEPS................................................................. 7
STEP 1. STARTING THE SOFTWARE .......................................... 7
STEP 2. PRINTER SETUP ........................................................... 7
STEP 3. PRINTER CALIBRATION ............................................... 9
Spectrocam Setup............................................................................. 10
Calibration Procedure ........................................................................10
Scanner................................................................................................... 13
Spectrocam ............................................................................................. 13
Spectrocam TIPs ...............................................................................16
STEP 4. ADDING A SPOOLER .................................................. 17
STEP 5. ADDING A HOT FOLDER ............................................. 19
STEP 6. SETTING PREFERENCES ............................................. 21
STEP 7. INSTALLING PPDS ..................................................... 25
STEP 8. JOB PRINTING ........................................................... 25
2002 Kodak Polychrome Graphics. All Rights Reserved.
3
Matchprint Professional Server for DocuColor 12 Printer/Copier – Quick Start
Product Safety and Compliance
Warning!
Do not modify or use any AC power cord other than the one included with shipping.
In some cases, the supplied power cord may not be compatible with the AC wall outlet in your region. If this is true, you must obtain a suitable power cord that meets the following criteria:
The cord must be rated for use at the AC voltage available, with a current rating that is at least 125% of the current rating of the product.
The AC plug end must be terminated in a grounding-type male plug designed for use in your region. The plug ends must be labeled or marked to indicate they have been certified by an agency acceptable in your region.
The connector at the product end must be an IEC 320, sheet C13, female connector (or the equivalent EN 60 320 connector.)
The cord must be less than 14.8 feet (4.5 meters) long and, for use in Europe, be created with <HAR> (harmonized) or VDE certified cordage.
Warning!
1. The user must never remove chassis covers. Some system circuitry retains voltage even when the system is turned off. Only qualified service technicians should remove chassis covers.
2. There are no user-serviceable components in the KPG server. Refer all system repair to a qualified service technician.
Warning!
The power supply voltage standby circuit is active when the computer is turned off. Ensure that the computer is disconnected from its power source and from all telecommunication links, networks, or modem lines whenever the chassis cover is removed. Do not operate the computer with the cover removed. Only qualified service technicians should remove chassis covers if repair or component replacement is required.
Warning!
Danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the equipment manufacturer. Discard used batteries according to manufacturer's instructions.
2002 Kodak Polychrome Graphics. All Rights Reserved.
4
Matchprint Professional Server for DocuColor 12 Printer/Copier – Quick Start
Sécurité et conformité du produit
Avertissement !
Ne modifiez ni n'utilisez aucun câble d'alimentation CA autre que celui qui vous a été livré avec le produit.
Il peut arriver, dans certaines régions, que le câble d'alimentation fourni ne soit pas compatible avec la prise de courant murale. Si tel est le cas, procurez­vous un câble d'alimentation adapté conforme aux critères suivants :
La puissance du câble doit correspondre à la tension CA disponible, avec un courant nominal d'au moins 125 % du courant nominal du produit.
Le câble CA doit avoir à son extrémité de branchement une fiche de terre mâle conçue et adaptée pour un usage dans votre région. Les fiches doivent être dotées d'une étiquette indiquant qu'elles ont été certifiées par une agence reconnue dans votre région.
Le connecteur à l'extrémité du produit doit être de type femelle IEC 320, blindé C13 (ou équivalent EN 60 320).
Le câble doit avoir une longueur maximum de 14,8 pieds (soit 4,5 mètres) et, en Europe, doit avoir été fabriqué à base de filin certifié <HAR> (norme harmonisée) ou VDE.
Avertissement !
1. L'utilisateur ne doit jamais ôter le couvercle du châssis. Certains circuits continuent d'être alimentés lorsque le système est hors tension. Seuls des techniciens de service qualifiés sont habilités à ôter le capot du châssis.
2. Aucun composant du serveur Professional ne peut être réparé par l'utilisateur. Tout dépannage doit être effectué par un technicien de service qualifié.
Avertissement !
Le circuit de réserve de tension d'alimentation reste actif lorsque l'ordinateur est éteint. Assurez-vous que l'ordinateur est débranché et que tous les réseaux, liaisons de télécommunications ou lignes de modem sont déconnectés lorsque le couvercle du châssis doit être ôté. Ne tentez jamais de faire fonctionner l'ordinateur tant que le couvercle n'est pas remis en place. Seuls des techniciens de service qualifiés sont habilités à ôter le couvercle du châssis si des réparations s'avèrent nécessaires ou qu'il est indispensable de remplacer des composants.
Avertissement !
Danger d'explosion si la batterie n'est pas parfaitement remise en place. Remplacez une batterie usée uniquement par le même type ou un type équivalent recommandé par le fabricant de l'appareil. Mettez les batteries usées au rebut conformément aux instructions du fabricant.
2002 Kodak Polychrome Graphics. All Rights Reserved.
5
Matchprint Professional Server for DocuColor 12 Printer/Copier – Quick Start
Service Information
Contact your Xerox representative for technical support or product related questions.
Agency Approvals
U.S. FCC Class A required, FCC Class B preferred
UL 1950 standard testing
Canada Canadian EMI Class A
CSA 950
Europe CISPR 22 Class B
CE Mark EN 60950 LUD
The radiated and conducted emissions are per EN 55022 class B limits. The radiated and conducted immunity are per EN 55024 class B limits.
For European safety, EN60950 under 73/23/EEC, Low Voltage Directive (LVD) amendment is correct.
Documentation
Online Help
Please refer to the Matchprint Professional Server (MPS) online help for more information on using new and existing features of the application.
To access the online help, launch the MPS application, then go to Help >
Read the User Guide.
Printable PDF of User’s Guide
There is also a user guide.pdf located on the application’s CD-ROM.
2002 Kodak Polychrome Graphics. All Rights Reserved.
6
Matchprint Professional Server for DocuColor 12 Printer/Copier – Quick Start

Quick Start Steps

To quickly get your system set up for printing from the client, go through the following procedures listed in the order shown:
Steps:
1. Start the Matchprint Professional Server software.
2. Printer Setup.
3. Printer Calibration.
4. Add a Spooler.
5. Add a Hot Folder.
6. Set Preferences.
7. Install PPDs.
8. Job Printing. You should now be able to successfully print from your client application to the DocuColor 12.

Step 1. Starting the Software

1. Double-click the Matchprint Professional Server software icon.
2. The Matchprint Professional Server main application window appears.

Step 2. Printer Setup

The software is shipped to you with the Printer Settings already set. However, you should confirm that the Media Settings (media type and size) for each tray match what is in your DocuColor 12.
Note: If the printer is deleted, you will need to perform the following printer setup instructions.
To add a printer or change printer settings, complete the following steps:
1. If you have had previous versions of the Matchprint Professional Server on your system, delete previous printers prior to adding new ones. If the system asks you if you want to delete previous files used only with this printer, select Yes.
2. Go to Printer > Add Printer or select Xerox DocuColor 12 (or the name of the printer you need to change). The Printer Settings window displays:
2002 Kodak Polychrome Graphics. All Rights Reserved.
7
Matchprint Professional Server for DocuColor 12 Printer/Copier – Quick Start
3. Confirm the desired Printer Options:
Active: Make sure this is checked. This ensures the printer is available to the
MPS RIP.
More Options... Not currently used.
Calibration...: Go to the Printer Calibration section for more information on
this topic.
Page Alignment...: Contains instructions on how to adjust Page Alignment.
CMYK Count, Gray Count, and Proof Count: Displays the current print
totals for those categories. The Proof Count can be reset to zero by clicking on the Reset Proof Count button.
4. Confirm the desired Media Settings for each tray and click OK.
The contents of each tray can vary from site to site, however standard tray setup is as follows:
Tray 1: Media Type - Normal Bond, Media Size - Letter (8.5 x 11 inches)
Tray 2: Media Type - Normal Bond, Media Size - Letter SEF (11 x 8.5 inches)
Tray 3: Media Type - Normal Bond, Media Size - Legal (8.5 x 14 inches)
Tray 4: Media Type - Normal Bond, Media Size - Tabloid (11 x 17 inches)
2002 Kodak Polychrome Graphics. All Rights Reserved.
8
Matchprint Professional Server for DocuColor 12 Printer/Copier – Quick Start
Tray 6 (High Capacity Feeder) – Optional: Media Type - Normal Bond, Media Size - Letter (8.5 x 11 inches)
Notes:
Tray 5 is a manual feed tray located on the left side of the Xerox DocuColor 12. (Tray 5 is not configured here.)
Load paper so the watermark wording is face down in the tray.
The DocuColor 12 can be set to disable automatic tray switching,
however the Matchprint Professional Server overrides this setting if the job's parameters are set to Automatically Select the input tray. Go to the Setting Job Parameters, Printer tab in the online help or the user guide.pdf for more information.

Step 3. Printer Calibration

KPG recommends daily calibration and recalibration each time the printer is serviced.
Calibrate for Bond medias using the following Xerox Color Xpressions media. When using supplied profiles and device links for premium medias, printer calibration must use the Matchprint Co-Branded Xerox Color Laser Proofing Paper. This is the only premium paper authorized by KPG and Xerox to accurately simulate Matchprint color.
The Color Profiles and Device Links supplied for normal, heavyweight, and extra heavyweight bond were all created using the following Xerox media:
Normal Bond: Xerox Color Xpressions 24 lb., Bright White 96 paper.
Heavyweight Bond: Xerox Color Xpressions 60 lb., Bright White 96 paper.
Extra Heavyweight Bond: Xerox Color Xpressions 80 lb., Bright White 98
paper.
Important! If a media other than the recommended Xerox media is used, the following error appears: “Warning! The media used for calibration appears to be significantly different from the Normal Bond (or Heavyweight) media recommended for used with this application. Results of the calibration on this media may not be typical.”
Printer calibration can be performed internally by using the DocuColor 12 built-in scanner or by using the Spectrostar Spectrocam, an external measurement device. Both procedures are described in this section. If calibration is to be performed using the Spectrocam, please go through the following Spectrocam Setup instructions before beginning the calibration process.
If calibration is to be performed using the DocuColor 12 scanner, please skip to the section titled, Calibration Procedure.
2002 Kodak Polychrome Graphics. All Rights Reserved.
9
Loading...
+ 18 hidden pages