KitchenAid KSC24C8EYY, WRS965CIAE, GSC25C4EYB, GSC25C4EYW, WRS965CIAH Installation Instructions Manual

...

INSTALLATION INSTRUCTIONS

Counter Depth Side by Side Refrigerator

IMPORTANT: READ AND SAVE THESE INSTRUCTIONS. INSTALLATION REQUIRES 2 OR MORE PEOPLE.

INSTRUCCIONES DE INSTALACIÓN

Refrigerador de dos puertas con profundidad de mostrador

IMPORTANTE: LEA Y GUARDE ESTAS INSTRUCCIONES. LA INSTALACIÓN REQUIERE DE 2 O MÁS PERSONAS.

INSTRUCTIONS D’INSTALLATION

Réfrigérateur côte à côte à profondeur de comptoir

IMPORTANT : LIRE ET CONSERVER CES INSTRUCTIONS. L’INSTALLATION NÉCESSITE L’INTERVENTION DE 2 PERSONNES OU PLUS.

Table of Contents / Índice / Table des matières

ASSISTANCE OR SERVICE ............................ 1

REFRIGERATOR SAFETY............................... 2

INSTALLATION REQUIREMENTS ................. 2

Tools and Parts ............................................. 2

Product Dimensions...................................... 2

Location Requirements................................. 4

Electrical Requirements ................................ 5

Water Supply Requirements......................... 5

INSTALLATION INSTRUCTIONS ................... 5

Unpack the Refrigerator................................ 5

Custom Door Panels..................................... 6

Install New Water Line .................................. 8

Connect Water Supply.................................. 9

Plug in Refrigerator ..................................... 10

Prepare the Water System.......................... 10

Leveling and Door Closing.......................... 11

Door Alignment ........................................... 11

Complete Installation .................................. 11

AYUDA O SERVICIO TÉCNICO.................... 12

SEGURIDAD DEL REFRIGERADOR ............ 12

REQUISITOS DE INSTALACIÓN .................. 12

Piezas y herramientas................................. 12

Medidas del producto................................. 13

Requisitos de ubicación.............................. 15

Requisitos eléctricos................................... 15

Requisitos del suministro de agua.............. 16

INSTRUCCIONES DE INSTALACIÓN .......... 16

Desempaque el refrigerador ....................... 16

Paneles para puerta a la medida................ 17

Cómo instalar la tubería de agua nueva..... 19

Conexión del suministro de agua ............... 20

Cómo enchufar el refrigerador.................... 21

Preparación del sistema de agua ............... 22

Nivelación y cierre de la puerta................... 22

Alineamiento de la puerta ........................... 23

Complete la instalación............................... 23

ASSISTANCE OU SERVICE .......................... 24

SÉCURITÉ DU RÉFRIGÉRATEUR................ 24

EXIGENCES D’INSTALLATION .................... 24

Outillage et pièces....................................... 24

Dimensions du produit................................ 25

Exigences d'emplacement ......................... 27

Spécifications électriques........................... 27

Spécifications de l’alimentation en eau ...... 28

INSTRUCTIONS D’INSTALLATION.............. 28

Déballage du réfrigérateur .......................... 28

Panneaux de porte personnalisés .............. 29

Installation d’une nouvelle

canalisation d’eau ....................................... 31

Raccordement de la canalisation d'eau ..... 32

Brancher le réfrigérateur ............................. 33

Préparer le système d'eau.......................... 34

Nivellement et fermeture de la porte .......... 34

Alignement des portes................................ 35

Achever l’installation ................................... 35

If You Have Questions

If you have questions about operating, cleaning or maintaining your refrigerator, see the Use & Care Guide.

If You Need Service

Maintain the quality built into your refrigerator by calling an authorized service company.

To locate an authorized service company, see the Use & Care Guide for the number to call, phone the dealer from whom you purchased the refrigerator, or check the yellow pages of your local phone directory.

W10168334A

Assistance or Service

Keep this book and your sales slip together for future reference. You must provide proof of purchase or installation date for in-warranty service.

Write down the following information about your appliance to help you obtain assistance or service if you ever need it. You will need to know your complete model number and serial number. You can find this information on the model and serial number label, located on the inside wall of the refrigerator compartment.

Dealer name____________________________________________________ Serial number __________________________________________________ Address ________________________________________________________ Phone number __________________________________________________ Model number __________________________________________________ Purchase date __________________________________________________

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

You can be killed or seriously injured if you don't immediately

DANGER

WARNING

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

follow instructions.

can be killed or seriously injured if you don't

You instructions.

INSTALLATION REQUIREMENTS

Tools and Parts

IMPORTANT:

■ Observe all governing codes and ordinances.

■ Installer: Leave Installation Instructions with homeowner.

■ Homeowner: Keep Installation Instructions for future reference

and for the local electrical inspector’s use.

■ Keep cardboard shipping piece or plywood under refrigerator

until it is installed in the operating position.

■ Comply with installation specifications and dimensions.

■ Remove any moldings or decorative panels from kitchen

cabinets that would not allow access to the refrigerator for service.

■ Contact a qualified electrical installer.

TOOLS NEEDED (on some models):

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

■ Cordless drill

■ ¹⁄₄" Nut driver

and drill bit

■ Flat-blade

screwdriver

PARTS NEE DED (on some models):

■ Your refrigerator dealer has a kit available with a ¹⁄₄" (6.35 mm)

saddle-type shutoff valve, a union, and copper tubing.

■ Or you can purchase a ¹⁄₄" (6.35 mm) copper tubing with

shutoff valve and a ¹⁄₄" (6.35 mm) compression fitting (coupling).

■ Depending on water line connections, you may also need a ¹⁄₄"

(6.35 mm) nut and ¹⁄₄" (6.35 mm) ferrule.

■ ⁵⁄₁₆" or adjustable wrench

■ ⁷⁄₁₆" and ¹⁄₂" Open-end wrenches

■ Two adjustable wrenches

■ ³⁄₈" and ¹⁄₂" Socket wrenches

Product Dimensions

Top View

⁵⁄₈"

35¹⁄₂"

(90.0 cm)

Door Style

15³⁄₈"

(38.9 cm)

Depth

20"

(50.8 cm)

Flat 27¹⁄₂"

(69.8 cm)

Curved 28⁵⁄₈"

(72.5 cm)

*Dimension may vary based on style of door handle.

The depth for the largest available handle is listed.

(1.6 cm)

23⁷⁄₈"

(60.4 cm)

Depth

2⁵⁄₈"(6.5cm)

maximum*

2⁵⁄₈"

(6.5 cm)

30" (76.3 cm)

Depth

maximum*

31¹⁄₈"

(79.1 cm)

Front View Side View

■ Height dimensions are shown with the leveling legs extended

to the minimum height of ¹⁄₄" (6.35 mm) below the refrigerator. NOTE: When leveling legs are fully extended to 1" (25 mm)

below the refrigerator, add ³⁄₄" (19 mm) to the height dimensions.

■ The power cord is 61¹⁄₄" (155.6 cm) long.

■ The water line attached to the back of the refrigerator is 78"

(198.1 cm) long.

35³⁄₄"

(90.8 cm)

Model Size Height A

69" 65³⁄₄" (166.9 cm) 72" 68¹⁄₈" (172.9 cm)

¹⁄₄"

(8.2 cm)

3¹⁄₄" (8.2 cm)

21³⁄₄"

(55.1 cm)

61¹⁄₄"

(155.6 cm)

Model Size Height A Height B Height C

69" 68⁷⁄₈"

(174.8 cm)

72" 71¹⁄₄"

(180.8 cm)

68⁷⁄₈"

(174.9 cm)

71¹⁄₄"

(180.9 cm)

68¹⁄₂"

(174.2 cm)

71"

(180.2 cm)

Opening Dimensions

Door Swing Dimensions

■ Height dimensions are shown with the leveling legs extended

to the minimum height of ¹⁄₄" (6.35 mm) below the refrigerator. NOTE: When leveling legs are fully extended to 1" (25 mm)

below the refrigerator, add ³⁄₄" (19 mm) to the height dimensions.

■ In the following graphic, “A” represents the opening height

required for standard cabinets. For full-overlay cabinet doors with a trim kit, add ¹⁄₈" (0.3 cm).

■ In the following graphic, “B” represents the distance needed

to fully open the freezer door and “C” represents the distance needed to fully open the refrigerator door.

36"

(91.4 cm)

■ Location must permit doors to open to a minimum of 165°.

■ In the following graphic, “A” represents the distance needed

to fully open the freezer door and “B” represents the distance needed to fully open the refrigerator door.

¹⁄₄" (104.5 cm)

90˚

165˚

45⁷⁄₈" (116.4 cm)

Dimension Flat Doors Curved Doors

A 13⁵⁄₈" (34.5 cm)

13³⁄₄" (34.9 cm)

maximum*

B 18¹⁄₈" (46.0 cm)

18³⁄₈" (46.4 cm)

maximum*

C 2³⁄₄" (6.7 cm)

3³⁄₄" (9.4 cm)

maximum*

Model Size

and

Height

Width

Door Style

69"

Flat

69"

(175.3 cm)

13⁵⁄₈"

(34.5 cm)

maximum*

72"

Flat

72"

(182.9 cm)

13⁵⁄₈"

(34.5 cm)

maximum*

69"

Curved

72"

Curved

69"

(175.3 cm)

72"

(182.9 cm)

13³⁄₄"

(34.9 cm)

13³⁄₄"

(34.9 cm)

*Dimension may vary based on style of door handle.

The width for the largest available handle is listed.

Width

18¹⁄₈"

(46.0 cm)

maximum*

18¹⁄₈"

(46.0 cm)

maximum*

18³⁄₈"

(46.4 cm)

18³⁄₈"

(46.4 cm)

D ¹⁄₈" (0.2 cm) 1¹⁄₄" (2.9 cm)

*Dimension may vary based on style of door handle.

The width for the largest available handle is listed.

Location Requirements

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

NOTES:

■ The cabinet depth refrigerator can be installed into a recessed

opening, at the end of cabinets or as a freestanding refrigerator.

■ If you are installing the refrigerator to fit flush with the front of

the base cabinets, all shoe molding and baseboards must be removed from the rear of the refrigerator opening. Allow for 1" (2.54 cm) of space behind the refrigerator.

■ Location should permit doors to open fully. See the “Door

Swing Dimensions” section.

■ Do not install the refrigerator near an oven, radiator, or other

heat source, nor in a location where the temperature will fall below 55°F (13°C).

■ Floor must support refrigerator weight (more than 600 lbs

[272 kg], door panels and contents).

Electrical Requirements

WARNING

Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical connection.

Recommended Grounding Method

A 115 volt, 60 Hz., AC only 15- or 20-amp fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your refrigerator be provided. Use an outlet that cannot be turned off by a switch. Do not use an extension cord.

IMPORTANT: If this product is connected to a GFCI (Ground Fault Circuit Interrupter) protected outlet, nuisance tripping of the power supply may occur, resulting in loss of cooling. Food quality and flavor may be affected. If nuisance tripping has occurred, and if the condition of the food appears poor, dispose of it.

NOTE: Before performing any type of installation, cleaning, or removing a light bulb, turn the control (Thermostat, Refrigerator or Freezer Control depending on the model) to OFF and then disconnect the refrigerator from the electrical source. When you are finished, reconnect the refrigerator to the electrical source and reset the control (Thermostat, Refrigerator or Freezer Control depending on the model) to the desired setting.

Water Pressure

A cold water supply with water pressure of between 30 and 120 psi (207 and 827 kPa) is required to operate the water dispenser and ice maker. If you have questions about your water pressure, call a licensed, qualified plumber.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the refrigerator needs to be between 30 and 120 psi (207 and 827 kPa).

If a reverse osmosis water filtration system is connected to your cold water supply, the water pressure to the reverse osmosis system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than 40 to 60 psi (276 to 414 kPa):

■ Check to see whether the sediment filter in the reverse

osmosis system is blocked. Replace the filter if necessary.

■ Allow the storage tank on the reverse osmosis system to refill

after heavy usage.

■ If your refrigerator has a water filter, it may further reduce the

water pressure when used in conjunction with a reverse osmosis system. Remove the water filter. See “Water Filtration System” in the Use & Care Guide.

If you have questions about your water pressure, call a licensed, qualified plumber.

INSTALLATION INSTRUCTIONS

Unpack the Refrigerator

WARNING

Excessive Weight Hazard

Use two or more people to move and install refrigerator.

Failure to do so can result in back or other injury.

Water Supply Requirements

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

TOOLS NEEDED:

■ Flat-blade screwdriver

■ ⁷⁄₁₆" and ¹⁄₂" Open-end or two

adjustable wrenches

NOTE: Your refrigerator dealer has a kit available with a ¹⁄₄" (6.35 mm) saddle-type shutoff valve, a union, and copper tubing. Before purchasing, make sure a saddle-type valve complies with your local plumbing codes. Do not use a piercing-type or ³⁄₁₆" (4.76 mm) saddle valve which reduces water flow and clogs more easily.

IMPORTANT:

■ All installations must meet local plumbing code requirements.

■ Use copper tubing and check for leaks. Install copper tubing

only in areas where the household temperatures will remain above freezing.

■ ¹⁄₄" Nut driver

■ ¹⁄₄" Drill bit

■ Cordless drill

Remove the Packaging

Dispose of/recycle all packaging materials. Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. These products can damage the surface of your refrigerator.

IMPORTANT:

■ Use ³⁄₈" socket wrench to remove skids.

■ All four leveling legs must contact the floor to support and

stabilize the full weight of the refrigerator.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator for cleaning or service, be sure to cover the floor with cardboard or hardboard to avoid floor damage. Always pull the refrigerator straight out when moving it. Do not wiggle or “walk” the refrigerator when trying to move it, as floor damage could occur.

Clean Before Using

Weight Limits

After you remove all of the package materials, clean the inside of your refrigerator before using it. See the cleaning instructions in the Use & Care Guide.

Important information to know about glass shelves and covers:

Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping. Tempered glass is designed to shatter into many small, pebble-size pieces. This is normal. Glass shelves and covers are heavy. Use both hands when removing them to avoid dropping.

Custom Door Panels

(on some models)

Custom door panels allow you to blend the exterior of your refrigerator into the overall kitchen décor. If you plan to install custom wood panels, you will need to create the panels yourself or consult a qualified cabinetmaker or carpenter. Follow these panel dimension and placement instructions to be sure that the custom panels will fit properly.

The custom panels must have backer panels attached in order to mount them to the refrigerator. It is most common to work with three panels, as shown in the following graphic: a ³⁄₄" (19.05 mm) decorative panel, a ¹⁄₁₆" (1.59 mm) spacer panel or spacer strips, and a ¹⁄₄" (6.35 mm) backer panel.

Decorative Panel

/4"

(19.05 mm)

(1.59 mm)

NOTE: You can also work with two panels, as shown in the following graphic: a ³⁄₄" (19.05 mm) decorative panel routed with a ¹⁄₁₆" (1.59 mm) cutout, and a separate ¹⁄₄" (6.35 mm) backer panel.

Decorative Panel

/16"

(17.46 mm)

/₁₆"

/16"

(1.59 mm)

Spacer Panel

Backer Panel

/4"

(6.35 mm)

Backer Panel

/4"

(6.35 mm)

Spacer Panel

/₁₆"

(1.59 mm)

Door Trim

/₁₆"

(1.59 mm)

Door Trim

1" minimum (2.54 cm)

Decorative

Panel

1" minimum (2.54 cm)

Decorative Panel

Backer Panel

(19.05 mm)

Backer Panel

/₄"

IMPORTANT: Panels weighing more than the recommended weight may cause damage to your refrigerator.

■ The weight of the freezer door panel(s) cannot exceed

25 lbs (11.3 kg).

■ The weight of the refrigerator door panel(s) cannot exceed

41 lbs (18.6 kg).

To minimize panel weight, you may use 2" (5.08 cm) spacer strips around the perimeter in place of solid full-sheet spacer panels. The spacer strips must be set in at least 1" (2.54 cm) from the top, bottom and side edges of the backer panel. If you use spacer strips, it is also recommended that you use two horizontally-centered 2" (5.08 cm) strips for added support.

Decorative Panel Dimensions

NOTE: The dashed line represents the placement of the dispenser

frame.

Refrigerator

Door Panel

Freezer Door Panel (Dispenser)

Freezer

Door Panel

(Non-Dispenser)

Dispenser cutout is centered left-to-right

Dimension Height/Width

A 19³⁄₈" (49.2 cm) B 31³⁄₄" (80.6 cm) C 68³⁄₁₆" (173.2 cm) D 15³⁄₈" (39.1 cm) E 20" (50.8 cm) F 17¹⁄₁₆" (43.3 cm) G 11¹⁵⁄₃₂" (29.1 cm)

Backer and Spacer Panel Dimensions

NOTE: The dashed lines represent the placement of the backer and spacer panels on the decorative panels. Backer and spacer panels should be centered vertically and horizontally.

2. Remove the side trim from each side of the freezer door.

D D

Dimension Backer Panel Spacer Panel

A 19" (48.3 cm) 18³⁄₈" (46.7 cm) B 31¹⁵⁄₃₂" (79.9 cm) 30³⁄₄" (78.1 cm)

3. Align the bottom edge of the door panel with the lower trim on

the bottom of the freezer door. Center the panel on the freezer door.

C 67²⁹⁄₃₂" (172.5 cm) 66⁹⁄₁₆" (169.1 cm) D 14⁷⁄₈" (37.8 cm) 14¹⁄₄" (36.2 cm) E 19¹⁄₂" (49.6 cm) 18⁷⁄₈" (47.9 cm)

Install the Door Panels

NOTE: In the graphics throughout this section, dark gray

represents the door trim and light gray represents the door panel.

1. Remove the upper trim from the top of the freezer door.

4. Reseat each side trim, making sure the trim clip slides inside

the corner of the lower trim.

A. Trim clip

5. With the side trims properly seated in the lower trim, slide

each trim into the door panel groove.

6. Align the upper trim with the trim clips at the top of each side

trim.

8. When fully seated, the upper trim should be nearly flush with

the top of the freezer door, completely covering both side trim clips.

9. Repeat the previous steps to install the refrigerator door

panel.

Install Dispenser Frame (dispenser models only)

After installing the custom door panels, snap the dispenser frame onto the freezer door as shown.

A. Trim clip

7. Slide the upper trim into the door panel groove by applying

firm downward pressure. Be sure that the grooves on the upper trim are properly aligned with the rivets on the door panel.

Install New Water Line

(if required)

TOOLS NEEDED:

■ Flat-blade screwdriver

■ ⁷⁄₁₆" and ¹⁄₂" Open-end or

two adjustable wrenches

1. Turn OFF main water supply. Turn ON nearest faucet long

enough to clear line of water.

2. Find a

¹⁄₂" (12.70 mm) to 1¹⁄₄" (3.18 cm) vertical cold water

pipe near the refrigerator. NOTE: Horizontal pipe will work, but the following procedure

must be followed:

■ Drill on the top side of the pipe, not the bottom. This will

help keep water away from the drill. This also keeps normal sediment from collecting in the valve.

3. Determine the length of copper tubing you need. Measure

from the connection on the lower left rear of refrigerator to the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use ¹⁄₄" (6.35 mm) O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing are cut square.

■ ¹⁄₄" Drill bit

■ Cordless drill

4. Using a cordless drill, drill a ¹⁄₄" (6.35 mm) hole in the cold

water pipe you have selected.

NOTE: To allow sufficient water flow to the refrigerator, a minimum ¹⁄₂" size copper household supply line is recommended.

DEF

A. Cold water pipe B. Pipe clamp C. Copper tubing D. Compression nut

E. Compression sleeve F. Shutoff valve

G. Packing nut

5. Fasten shutoff valve to cold water pipe with pipe clamp. Be

sure outlet end is solidly in the

¹⁄₄" (6.35 mm) drilled hole in the

water pipe and that washer is under the pipe clamp. Tighten packing nut. Tighten the pipe clamp screws slowly and evenly so washer makes a watertight seal. Do not overtighten or you may crush the copper tubing, especially if soft (coiled) copper tubing is used. Now you are ready to connect the copper tubing.

6. Slip compression sleeve and compression nut on copper

tubing as shown in the diagram. Insert the end of the tubing into the outlet end of the shutoff valve as far as it will go. Screw the compression nut onto the outlet end with an adjustable wrench. Do not overtighten.

7. Place the free end of the tubing into a container or sink, turn

ON main water supply and flush out tubing until water is clear. Turn OFF the shutoff valve on the water pipe.

Connect Water Supply

Read all directions before you begin.

IMPORTANT:

■ Plumbing shall be installed in accordance with the

International Plumbing Code and any local codes and ordinances.

■ Use copper tubing or Whirlpool supply line, Part Number

8212547RP, and check for leaks.

■ Install tubing only in areas where temperatures will remain

above freezing.

TOOLS NEEDED:

Gather the required tools and parts before starting installation.

■ Flat-blade screwdriver

■ ⁷⁄₁₆" and ¹⁄₂" open-end wrenches or two adjustable wrenches

■ ¹⁄₄" nut driver

A B

A. Bulb B. Nut

C. Copper tubing (to refrigerator) D. Household supply line (½" minimum)

4. Now you are ready to connect the copper tubing to the shutoff

valve. Use ¹⁄₄" (6.35 mm) OD soft copper tubing to connect the shutoff valve and the refrigerator.

■ Ensure that you have the proper length needed for the job.

Be sure both ends of the copper tubing are cut square.

■ Slip compression sleeve and compression nut onto

copper tubing as shown. Insert end of tubing into outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjustable wrench. Do not overtighten.

B CA

A. Compression sleeve B. Compression nut

C.Copper tubing

5. Place the free end of the tubing into a container or sink, and

turn on main water supply to flush out tubing until water is clear. Turn off shutoff valve on the water pipe.

NOTE: Always drain the water line before making the final connection to the inlet of the water valve, to avoid possible water valve malfunction.

6. Bend the copper tubing to meet the water line inlet, which is

located on the back of the refrigerator cabinet as shown. Leave a coil of copper tubing to allow the refrigerator to be pulled out of the cabinet or away from the wall for service.

Connect to Refrigerator

Connect to Water Line

IMPORTANT: If you turn the refrigerator on before the water line is

connected, turn the ice maker OFF.

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long

enough to clear line of water.

3. Use a quarter-turn shutoff valve or the equivalent, served by a

¹⁄₂" copper household supply line.

Style 1

1. Unplug refrigerator or disconnect power.

2. Remove and discard the short, black plastic part from the end

of the water line inlet.

3. Thread the nut onto the end of the tubing. Tighten the nut by

hand. Then tighten it with a wrench two more turns. Do not overtighten.

NOTE: To avoid rattling, be sure the copper tubing does not touch the cabinet’s side wall or other parts inside the cabinet.

DA B C

A. Line to refrigerator B. Nut (purchased)

C. Ferrule (purchased) D. Supplied line from refrigerator

4. Install the water supply tube clamp around the water supply

line to reduce strain on the coupling.

5. Turn shutoff valve ON.

6. Check for leaks. Tighten any connections (including

connections at the valve) or nuts that leak.

Style 2

1. Unplug refrigerator or disconnect power.

2. Remove and discard the plastic part that is attached to the

inlet of the water valve.

3. Attach the copper tube to the valve inlet using a compression

nut and sleeve as shown. Tighten the compression nut. Do not overtighten.

4. Use the tube clamp on the back of the refrigerator to secure

the tubing to the refrigerator as shown. This will help avoid damage to the tubing when the refrigerator is pushed back against the wall.

5. Turn shutoff valve ON.

6. Check for leaks. Tighten any connections (including

connections at the valve) or nuts that leak.

A B

D E

A. Tube clamp B. Tube clamp screw C. Copper tubing

7. On some models, the ice maker is equipped with a built-in

water strainer. If your water conditions require a second water strainer, install it in the ¹⁄₄" (6.35 mm) water line at either tube connection. Obtain a water strainer from your nearest appliance dealer.

D. Compression nut

E. Valve inlet

Style 3

1. Unplug refrigerator or disconnect power.

2. Remove and discard the black nylon plug from the gray water

tube on the rear of the refrigerator.

3. If the gray water tube supplied with the refrigerator is not long

enough, a ¹⁄₄" x ¹⁄₄" (6.35 mm x 6.35 mm) coupling is needed in order to connect the water tubing to an existing household water line. Thread the provided nut onto the coupling on the end of the copper tubing.

NOTE: Tighten the nut by hand. Then tighten it with a wrench two more turns. Do not overtighten.

A B C D E F G

A. Refrigerator water tubing

B. Nut (provided) C. Bulb D. Coupling (purchased)

E. Ferrule (purchased) F. N ut ( p ur cha s ed )

G. Household water line

Plug in Refrigerator

WARNING

Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

1. Plug into a grounded 3 prong outlet.

Prepare the Water System

Please read before using the water system. Immediately after installation, follow the steps below to make sure

that the water system is properly cleaned.

1. Open the freezer door and turn off the ice maker. The On/Off

switch can only be accessed when the ice storage bin has been removed. The switch is located on the freezer door, on the left side of the wall that surrounds the ice storage bin. Move the switch to the OFF (right) setting.

2. Make sure the water filter is properly installed.

Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.

3. Flush the water system. Use a sturdy container to depress

and hold the water dispenser lever for 5 seconds, then release it for 5 seconds. Repeat until water begins to flow. Once water begins to flow, continue depressing and releasing the dispenser lever (5 seconds on, 5 seconds off) until a total of 3 gal. (12 L) has been dispensed. This will flush air from the filter and water dispensing system, and prepare the water filter for use. Additional flushing may be required in some households. As air is cleared from the system, water may spurt out of the dispenser.

4. Open the freezer door and turn on the ice maker. Move the

switch to the ON (left) position. See the Use & Care Guide for further instructions on the operation of your ice maker.

■ Allow 24 hours to produce the first batch of ice.

■ Discard the first three batches of ice produced.

■ Depending on your model, you may want to select the

maximum ice feature to increase the production of ice.

4. Turn shutoff valve ON.

5. Check for leaks. Tighten any nuts or connections (including

connections at the valve) that leak.

Leveling and Door Closing

Your refrigerator has two adjustable front feet — one on the right and one on the left. In most cases, the refrigerator should be steady when both feet are touching the floor. If your refrigerator seems unsteady or if you want the doors to close more easily, adjust the refrigerator's tilt using the instructions below:

1. Move the refrigerator into its final location. Open both doors

to 90°. Remove the base grille by removing the two screws, then pulling out on the outside corners.

NOTE: The doors must only be opened to 90°. If they are opened all the way, the base grille will not come off.

2. The two leveling feet are located on the brackets on each side

of the product.

Door Alignment

A refrigerator that is not level from side-to-side may appear to have doors that are not properly aligned. If the doors appear this way, use the instructions in the previous section to check the leveling.

The doors are designed to be slightly different heights when the refrigerator is empty, in order to account for the weight of food that will be placed on the doors. If the doors are still not aligned after checking the leveling and loading the refrigerator with food, follow the steps below to adjust the door alignment.

1. If necessary, open both doors to 90° and remove the base

grille.

2. Locate the alignment screw on the bottom hinge of the

refrigerator door.

Raise

A. Bottom hinge B. Leveler bracket C. Leveling foot

Lower

NOTE: Having someone push against the top of the refrigerator takes some weight off the leveling feet. This makes it easier to make adjustments.

3. Use a ¹⁄₄" open-ended or adjustable wrench to adjust the

leveling feet. Turn the leveling foot to the left to raise that side of the product, or turn it to the right to lower that side of the product.

4. Open both doors again and check that they close as easily as

you like. If not, tilt the refrigerator slightly more to the rear by turning the leveling feet to the left. It may take several more turns, and you should turn both leveling feet the same amount.

NOTE: Whenever you need to move the refrigerator, turn the leveling feet to the right until they are no longer touching the ground. This will allow the refrigerator to roll more easily.

Lower

A. Alignment screw

Raise

3. Use a ⁵⁄₁₆" open-ended or adjustable wrench to turn the screw.

To raise the refrigerator door, turn the screw to the right. To lower the door, turn the screw to the left.

4. Check that the doors are even at the top. If necessary,

continue to turn the alignment screw until the doors are aligned.

5. Open both doors to 90°. Replace the base grille.

Complete Installation

1. Turn water supply line valve to “Open” position.

2. Turn refrigerator switch to ON position. Wait a few minutes.

Check water line connections for leaks.

3. Set refrigerator and freezer compartment controls to the

midpoint setting. Check that the compressor is operating properly and that all lights are working.

4. Flush water system before using. See “Prepare the Water

System.”

NOTE: If construction will continue after refrigerator has been installed, set controls to OFF.

If Refrigerator Does Not Operate

■ Check that the circuit breaker is not tripped or household fuse

blown.

■ Check that the power supply cord is plugged into a grounded

3prong outlet.

■ See “Troubleshooting” in the Use & Care Guide.

+ 25 hidden pages