KitchenAid KRFC804GPS, KRFC804GSS Owner's Manual

DOOR-WITHIN-DOOR FRENCH DOOR REFRIGERATOR

Use and Care Guide

IMPORTANT: READ AND SAVE THESE INSTRUCTIONS. INSTALLATION REQUIRES TWO OR MORE PEOPLE.

RÉFRIGÉRATEUR À DOUBLE BATTANT

AVEC PORTE DOUBLE

Guide d’utilisation et d’entretien

IMPORTANT : LIRE ET CONSERVER CES INSTRUCTIONS. L’INSTALLATION NÉCESSITE

L’INTERVENTION DE DEUX PERSONNES OU PLUS.

REFRIGERADOR DE PUERTAS FRANCESAS DOBLE PUERTA

Manual del usuario

IMPORTANTE: LEA Y GUARDE ESTAS INSTRUCCIONES. SE REQUIEREN DOS O MÁS PERSONAS

PARA REALIZAR LA INSTALACIÓN.

Table of Contents/Table des matières/Índice..................................................................

W10913649D

TABLE OF CONTENTS/TABLE DES MATIÈRES/ÍNDICE

REFRIGERATOR SAFETY........................	3
PARTS AND FEATURES...........................	4
What’s New Behind the Doors?.............	5
GETTING STARTED..................................	6
REFRIGERATOR CONNECTIVITY
FEATURES.................................................	8
INSTALLATION INSTRUCTIONS.............	9
Unpack the Refrigerator.........................	9
Location Requirements...........................	9
Remove and Replace Refrigerator
Doors.....................................................	10
Remove and Replace
Freezer Drawer Fronts..........................	13
Electrical Requirements........................	14
Water Supply Requirements.................	14
Connect the Water Supply...................	14
Handle Installation and Removal................
15
Refrigerator Leveling
and Door Closing..................................	17
FILTERS AND ACCESSORIES ..............	18
Water Filtration System........................	18
Install Air Filter.......................................	19
Install Produce Preserver......................	19
Accessories...........................................	20
REFRIGERATOR USE.............................	20
Opening and Closing Doors.................	20
Using the Controls................................	21
External Dispenser Controls.................	22
Lighting the Refrigerator.......................	23
Water and Ice Dispensers.....................	23
Ice Maker and Storage Bin ..................	26
Shelves, Bins, and Drawers..................	27
Freezer Drawers....................................	30
Audio Reference...................................	30
REFRIGERATOR CARE..........................	31
Cleaning................................................	31
Lights....................................................	32
Vacation and Moving Care...................	32
TROUBLESHOOTING.............................	33
PERFORMANCE DATA SHEET..............	40
WARRANTY.............................................	41

SÉCURITÉ DU RÉFRIGÉRATEUR.........	42	SEGURIDAD DEL REFRIGERADOR.....	85
PIÈCES ET CARACTÉRISTIQUES.........	43	PIEZAS Y CARACTERÍSTICAS..............	86
Quoi de neuf en coulisse?....................	44	¿Qué hay de nuevo detrás de
MISE EN PLACE.......................................	45	las puertas?..........................................	87
FONCTIONS DE CONNECTIVITÉ		PARA COMENZAR...................................	88
DU RÉFRIGÉRATEUR..............................	47	CARACTERÍSTICAS DE CONECTIVIDAD
INSTRUCTIONS D’INSTALLATION........	48	DEL REFRIGERADOR.............................	90

Déballage du réfrigérateur....................	48
Exigences d’emplacement...................	48
Retrait et réinstallation des portes
du réfrigérateur.....................................	49
Retrait et réinstallation de l’avant
du tiroir de congélation.........................	52
Spécifications électriques.....................	53
Spécifications de l’alimentation
en eau...................................................	53
Raccordement à la canalisation
d’eau.....................................................	53
Installation et retrait des poignées.......	54
Nivellement du réfrigérateur
et fermeture de la porte........................	56
FILTRES ET ACCESSOIRES .................	57
Système de filtration d’eau...................	57
Installation du filtre à air........................	58
Installation du conservateur de
produits frais.........................................	59
Accessoires...........................................	59
UTILISATION DU RÉFRIGÉRATEUR.....	60
Ouverture et fermeture des portes.......	60
Utilisation des commandes..................	61
Commandes de distributeur externe....	63
Éclairage du réfrigérateur.....................	63
Distributeurs d’eau et de glaçons........	63
Machine à glaçons et bac
d’entreposage ......................................	66
Tablettes, balconnets et tiroirs..............	68
Tiroirs du congélateur...........................	71
Référence audio....................................	71
ENTRETIEN DU RÉFRIGÉRATEUR.......	72
Nettoyage..............................................	72
Lampes.................................................	73
Précautions à prendre pour les
vacances ou le déménagement...........	73
DÉPANNAGE...........................................	74
FICHE DE DONNÉES RELATIVES AU
RENDEMENT...........................................	82
GARANTIE...............................................	83

INSTRUCCIONES DE INSTALACIÓN....	91
Desembale el refrigerador....................	91
Requisitos de ubicación.......................	91
Cómo retirar y volver a colocar
las puertas del refrigerador...................	92
Cómo retirar y volver a colocar el
frente de los cajones del congelador...	95
Requisitos eléctricos.............................	96
Requisitos de suministro de agua........	96
Conexión del suministro de agua.........	96
Cómo instalar y quitar las manijas.......	98
Nivelación del refrigerador
y cierre de las puertas..........................	99
FILTROS Y ACCESORIOS ...................	100
Sistema de filtración de agua.............	100
Instalación del filtro de aire.................	102
Instale el preservador de alimentos
frescos.................................................	102
Accesorios..........................................	103
USO DEL REFRIGERADOR.................	103
Cómo abrir y cerrar las puertas..........	103
Uso de los controles...........................	104
Controles del despachador externo...	106
Iluminación del refrigerador................	106
Despachadores de agua y de hielo....	106
Fábrica de hielo y depósito ...............	110
Estantes, depósitos y cajones............	111
Cajones del congelador......................	114
Referencia de audio............................	114
CUIDADO DEL REFRIGERADOR........	115
Limpieza..............................................	115
Luces...................................................	116
Cuidado durante las vacaciones
y las mudanzas...................................	116
SOLUCIÓN DE PROBLEMAS..............	117
HOJA DE DATOS DE RENDIMIENTO. 124
GARANTÍA.............................................	125

■ A qualified service technician must install the water line and ice maker.

■ Connect to a potable water supply only.

■ Use a sturdy glass when dispensing ice (on some models). ■ This appliance is not intended for use by persons (including

children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

■ Children should be supervised to ensure that they do not play with the appliance.

■ To avoid the risk of children becoming trapped and suffocating, do not allow them to play or hide inside the refrigerator.

■ If the power supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person.

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.

many important safety messages in this manual and on your appliance. Always read and obey all safety

safety alert symbol.

alerts you to potential hazards that can kill or hurt you and others.

messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.” mean:

DANGER WARNING

You can be killed or seriously injured if you don't immediately follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions: ■ Plug into a grounded (earthed) outlet.

■ Do not remove ground prong. ■ Do not use an adapter.

■ Do not use an extension cord.

■ Disconnect power before servicing.

■ Replace all parts and panels before operating. ■ Remove doors from your old refrigerator.

■ Use nonflammable cleaner.

■ Do not store or use petrol, flammable liquids or gas in the vicinity of this or other electrical appliances. The fumes can cause fires or explosions.

■ Do not store explosive substances such as aerosol cans with a flammable propellant in this refrigerator.

■ Do not use or place electrical devices inside the refrigerator compartments if they are not of the type expressly authorized by the manufacture.

■ Use two or more people to move and install refrigerator.

■Disconnect power before installing ice maker (on ice maker kit ready models only).

SAVE THESE INSTRUCTIONS

State of California Proposition 65 Warnings:

WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other reproductive harm.

KitchenAid KRFC804GPS, KRFC804GSS Owner's Manual

Proper Disposal of

Your Old Refrigerator

WARNING

Suffocation Hazard Remove doors from your old refrigerator.

Failure to do so can result in death or brain damage.

IMPORTANT: Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still dangerous—even if they will sit for “just a few days.” If you are getting rid of your old refrigerator, please follow these instructions to help prevent accidents.

Before You Throw Away Your Old Refrigerator or Freezer:

■Take off the doors.

■Leave the shelves in place so that children may not easily climb inside.

Important information to know about disposal of refrigerants:

Dispose of refrigerator in accordance with Federal and Local regulations. Refrigerants must be evacuated by a licensed, EPA certified refrigerant technician in accordance with established procedures.

PARTS AND FEATURES

	In-Door-Ice®
	ice storage
	Temperature	Slide-away split
	control UI	Slide-away split
	control UI	shelf
		shelf
	Under-shelf
	prep zone
	Air filter	Self-close
	Air filter	pull-out tray
		pull-out tray
	FreshSeal™
	Herb
	storage	FreshSeal™
	bin	FreshSeal™
		crispers
	Water filter	Temperature-
	Water filter	controlled
		controlled
		pantry drawer

Removable

bins Full Gallon Storage pull-out

bins

FreshVue™ Door-within-Door

What’s New Behind the Doors?

Your KitchenAid® Door-Within-Door French Door Refrigerator comes equipped with various innovative storage and energy-efficient features.

FreshVue™ Door-within-Door

Provides a tinted exterior storage door with four bins and a window that lights up as you approach it. The proximity lighting provides visibility, while the door allows easy access to frequently used ingredients without opening the main refrigerator.

Auto Light Interior LED Lighting

Rows of bright LED mounted lights slowly illuminate as you approach and gradually turn off when you walk away making it easy to find ingredients inside your refrigerator without opening the door.

3-Tier Self-Close Freezer Drawer with Extend-Freeze™ Setting or 3-Tier Self-Close Freezer Drawer with Ice Maker (depending on models)

A drawer system that organizes items on three levels making them easier to store and find. The lower drawer includes a divider. There’s also an in-door pizza pocket, a pull-out drawer for smaller items and third level glass shelf for small, flat items.

The Extend-Freeze™ setting takes the entire freezer to its coldest setting to help reduce freezer burn and extend the life of frozen items.

In-Door-Ice® Ice Dispensing System

Under-Shelf Prep Zone

A slide-out pan utilizes empty space beneath the shelf to create a prep zone ideal for dough, desserts, or marinating meats. Slideout pan is ovenand dishwasher-safe, and easily transitions from fridge to oven so you can stay in the creative flow.

Slide-Away Split Shelf

This shelf features a versatile design that allows three-quarters of the shelf to retract to accommodate taller items, up to 16¾" (42.5 cm). This flexibility helps maximize storage space and optimize organization.

FreshSeal™ Crispers

These upgraded crisper drawers use a gasket seal to maintain the ideal temperature and humidity levels to keep produce fresh longer. These drawers also feature premium soft-close glides that provide the best extension for easy access and maximum visibility to your produce items.

Full-Extension Self-Close Custom TemperatureControlled Pantry Drawer

Four temperature presets are available on the interior control to keep items at the optimal temperature. You can choose from meat/fish, cold drinks, deli/cheese, and wine. Pantry drawer slides open effortlessly, even when fully loaded, with soft, selfclose glides, and features the best extension in freestanding refrigeration.

Full-Extension Self-Close Pull Out Tray

The tray fully extends for easy access and visibility. The tray also features soft self-close glides that provide effortless movement, even when fully loaded. The tray is removable, making cleaning easy.

Preserva® Food Care System with Linear Compressor

The ice maker and ice storage bin are located in the door for easy access to filtered ice while freeing up valuable shelf space inside.

Panoramic LED Lighting

Increased visibility to your ingredients with strips of lighting on the sides, ceiling, and back of the refrigerator, as well as in the crisper and pantry. LED lights are maintenance-free and do not require replacement.

PrintShield™ Finish

Resists smudges and fingerprints. The specialized coating for stainless steel is easy to clean with just water and a soft cloth.

Wi-Fi Connectivity

This refrigerator can connect with in-home Wi-Fi to provide remote control through app, available to download for use with either iOS or Android devices.

Water Dispenser with Measured Fill

The Measured Fill feature allows you to dispense a desired amount of filtered water in handy increments of 8, 16, or 24 oz.

Water Dispenser with Favorite Fill

The Favorite Fill feature allows you to save two custom presets that can be programmed for favorite items that are frequently filled like a coffee pot or a water bottle.

FreshSeal™ Herb Storage Bin

This is a cylinder with FreshSeal™ to keep sensitive items like herbs fresh longer. The container allows water to be added to keep stems wet without covering leaves. It can be placed anywhere in the refrigerator and accommodates tall items like

parsley, cilantro, and rosemary in addition to herbs like oregano, thyme, and mint.

Provides the height of food preservation with two independent cooling systems plus a Produce Preserver to help keep food at its peak. The Linear Compressor’s efficient cooling system offers minimal temperature variation, which makes this is our quietest freestanding French door refrigerator.

Produce Preserver

Ethylene is a natural gas produced by fruits and vegetables to promote ripening. The Produce Preserver absorbs ethylene to delay the over-ripening of fresh produce. As a result, certain produce items will stay fresh longer.

Adjustable Shelves on Flipper System

Shelves that can be adjusted up or down easily with the flip of a lever, allowing them to be adjusted without having to unload them. The shelves are easy to clean and let you use the whole shelf edge to edge for full visibility and accessibility.

FreshSeal™ Dairy Bin

A dedicated dairy bin with the FreshSeal™ gasket to help extend the freshness and preserve the flavor of butter and other dairy items.

Air Filter

Removable Door Bins

An air filter is 15 times more powerful than baking soda at reducing common food odors inside the refrigerator. Replace your air filter every 6 months for maximum odor reduction.

EveryDrop® Water Filter

EveryDrop® water filters are NSF®† Certified to reduce most contaminants, including chlorine taste and odor, lead, pesticides, and trace amounts of pharmaceuticals. EveryDrop® brand

filters are the only filters tested and certified for your refrigerator system. Replace your EveryDrop® filter every 6 months for maximum contaminant reduction.

Door bins that can be easily removed from the metal finish base they sit on, making them ideal for carrying condiments or items from refrigerator to table. The bins are dishwasher-safe for easy cleaning.

Power Outage Indicator

If the power should go out while you are away from home, this indicator will let you know that the refrigerator has been without power.

To view videos on door removal/ replacement, door adjustment, water filter installation, air filter installation, shelf adjustment or removal, and Wi-Fi connectivity (if applicable), scan the code to the left with your mobile device.

GETTING STARTED

INSTALLATION CHECKLIST

Electrical Power

WARNING

Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

Plug refrigerator into a grounded 3 prong outlet.

Doors

If doors need to be removed during installation, see the “Remove and Replace Doors” section in the instructions.

Check that handles are secure and installed according to the instructions.

Doors seal completely.

Refrigerator is level. (Remove base grille and adjust leveling feet so they are snug against the floor.)

Doors are even across the top. (Use door alignment feature if necessary.)

Base grille is properly attached to the refrigerator.

Ice and Water System (on some models)

Connect refrigerator to a cold water supply with

20-120 psi (1.4-8.4 Kg/cm) water pressure, as specified in the instructions.

Make sure the household water supply is connected and turned on.

Check that the water supply line behind refrigerator is not kinked.

Only use recommended water supply tubing, copper, or PEX, as specified in the instructions.

†®NSF is a registered trademark of NSF International.

Install water filter according to the instructions.

Flush water system with 3 gallons (11.4 L) of water, as specified in the instructions.

Check for water leaks at all connections.

Turn on ice maker if refrigerator is connected to water supply. (If not connected to water supply, turn off ice maker.)

Final Checks

Install air filter and Produce Preserver according to instructions in corresponding packaging.

Remove all shipping material.

Set temperature controls to the recommended setting.

Save instructions and other literature.

Send in registration card or register your product online.

WATER FILTER INSTALLATION

Locate the water filter compartment in the lower left-hand side of the refrigerator compartment. Push on the right side of the filter door to open.

Align the arrow on the water filter cap with the cutout notch in the filter housing and insert filter.

Once the filter is inserted, turn the filter clockwise 90° (1/4 turn) until it locks into the housing.

Push water filter door closed to latch.

Flush 3 gallons (11.4 L) of water through the water system to clear air from the water line and to keep the dispenser from dripping and/or avoiding decreased dispenser flow.

NOTE: If the filter is not installed correctly, water may dispense at a lower flow rate and there will be slower ice production. Improper filter installation may also cause the

water filter housing to leak.

DOOR ALIGNMENT

Tools Required

Depending on the width of the door opening, the following tools may be required to remove, replace, and align the refrigerator doors.

Tools Needed:

■■ 1/4" hex nut driver – base grille, freezer drawer screws, and brake/leveling feet

Tools Provided:

■■ 1/8" hex key – handle setscrews and door alignment

Door alignment tool instructions

Features:

■■ Creates an even horizontal gap between the refrigerator doors.

■■ Solves door alignment issues

during installation and improves door seal.

Shelf Height Adjustment

Shelf height can be adjusted by changing the adjustable shelf mounts between their vertical and horizontal positions.

Carefully lift the shelf off the shelf mounts and turn the flipper to the desired orientation.

Repeat for remaining shelf mounts.

Ensure the shelf is properly seated on the shelf mounts.

Align Refrigerator Doors

If doors are uneven:

Ensure the refrigerator is level.

Keeping both refrigerator doors closed, pull out the freezer drawer. Locate the bottom hinge pin of the right-hand refrigerator door. The alignment screw is inside the bottom hinge pin.

Insert the short end of the 1/8" hex key wrench (packed with the Door Handle Installation Instructions) into the bottom hinge pin until it is fully engaged in the alignment screw.

To raise the refrigerator door, turn the hex key to the right. To lower the door, turn the hex key to the left.

Continue to turn the alignment screw until the tops of the doors are aligned.

A.Bottom hinge pin

B.1/8" hex key wrench

ENERGY SAVER MODE AND NORMAL OPERATING SOUNDS

Your new Door-Within-Door French Door Refrigerator has been designed to optimize energy efficiency and better regulate temperatures to match cooling demand.

You may notice that it operates differently from your previously owned refrigerator.

It is normal for the high-efficiency compressor to run for extended periods of time at varying speeds in order to consume only the energy necessary for optimum efficiency.

In addition, during various stages of the cooling cycle, you may hear normal operating sounds that are unfamiliar to you.

Energy Saver Mode

Turns off the anti-sweat heaters to save the customer power. When the icon is bright, the function is activated (heaters off); icon off means that it is inactive (heaters on). The user can toggle the feature by pressing the button. If the user lives in a climate with high humidity, Energy Saver mode is not recommended.

REFRIGERATOR CONNECTIVITY FEATURES (ON SOME MODELS)

Wi-Fi connectivity allows your Smart Refrigerator to connect to the Internet and interact with the KitchenAid™ App from your smartphone or mobile device. Check any connection instructions for your specific router, and refer to alternate instructions at www.kitchenaid.com/connect or call 1-877-559-2603.

NOTE: KitchenAid™ App features and functions are subject to change.

SMART FEATURES

Smart Features help make your everyday a little more efficient by letting you remotely monitor, manage, and maintain your refrigerator.

Remote Temperature Control

What it does: Allows you to control the temperature of your refrigerator remotely from your mobile device via the KitchenAid™ App.

What it does for you: Lets you control temperatures in your refrigerator, freezer, and temp-controlled pantry remotely—not just when you are standing in front of it.

Water and Air Filter Status

What it does: Gives you a look at the life remaining for your air and water filters before replacement is needed.

What it does for you: Helps you be more efficient in planning for ordering and replacing filters.

Door Open Alert

What it does: Sends you a notification when one of the doors of the refrigerator has been left open.

What it does for you: Alerts you to Door Ajar status so you can close the door(s) or call home to ask someone else to close the door before an over-temp situation arises.

Power Outage

What it does: Sends you a notification when power to your refrigerator goes out, returns, or highest temperature is reached in the refrigerator and freezer compartments.

What it does for you: Alerts you to power status and duration of outage to provide input regarding disposition of refrigerator/ freezer contents.

Max Ice/Max Cool Control

What it does: Allows you to control your refrigerator remotely from your mobile device via the KitchenAid™ App.

What it does for you: Lets you turn on/off Mac Ice and Max Cool options remotely to increase ice production or make temperatures colder in refrigerator and freezer in anticipation of loading in newly purchased grocery items.

GET STARTED

Go to www.kitchenaid.com/connect and follow the instructions to get connected.

Check the KitchenAid™ App frequently for additional information and features.

Requires Wi-Fi and account creation. KitchenAid™ App features and functionality subject to change. Subject to Terms of Service available at: www.kitchenaid.com/connect. Data rates

may apply.

INSTALLATION INSTRUCTIONS

Unpack the Refrigerator

WARNING

Excessive Weight Hazard

Use two or more people to move and install refrigerator.

Failure to do so can result in back or other injury.

Refrigerator Delivery

■■ A minimum door opening of 33" (838 mm) is required. If door opening is 36" (914 mm) or less, then removal of doors, drawer, and hinges is required.

■■ Cart the refrigerator from the side for all door openings.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator for cleaning or service, be sure to cover the floor with cardboard or hardboard to avoid floor damage. Always pull the refrigerator straight out when moving it. Do not wiggle or “walk” the refrigerator when trying to move it, as floor damage could occur.

Remove the Packaging

■■ Remove tape and glue residue from surfaces before turning on the refrigerator. Rub a small amount of liquid dish soap over the adhesive with your fingers. Wipe with warm water and dry.

■■ Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. These products can damage the surface of your refrigerator.

■■ Dispose of/recycle all packaging materials.

Clean Before Using

Location Requirements

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

IMPORTANT: This appliances is intended to be used in household and similar applications such as:

■■ Staff kitchen areas in shops, office and other working environments,

■■ Farm houses and by clients in hotels, motels and other residential type environments,

■■ Bed and breakfast type environments,

■■ Catering and similar non-retail applications.

To ensure proper ventilation for your refrigerator, allow for a 1/2" (1.25 cm) space on each side and at the top. Allow for a

1" (2.54 cm) space behind the refrigerator. If your refrigerator has an ice maker, allow extra space at the back for the water line connections. When installing your refrigerator next to a fixed wall, leave a 3 3/4" (9.5 cm) minimum space between the refrigerator and wall to allow the door to swing open.

NOTE: This refrigerator is intended for use in a location where the temperature ranges from a minimum of 55°F (13°C) to a maximum of 110°F (43°C). The preferred room temperature range for optimum performance, which reduces electricity usage and provides superior cooling, is between 60°F (15°C) and 90°F (32°C). It is recommended that you do not install the refrigerator near a heat source, such as an oven or radiator.

After you remove all of the packaging materials, clean the inside of your refrigerator before using it. See the cleaning instructions in the “Refrigerator Care” section.

Important information to know about glass shelves
Important information to know about glass shelves
and covers:		1/2" (1.25 cm)
Do not clean glass shelves or covers with warm water when


they are cold. Shelves and covers may break if exposed to
sudden temperature changes or impact, such as bumping.
sudden temperature changes or impact, such as bumping.
Tempered glass is designed to shatter into many small,
pebble-size pieces. This is normal. Glass shelves and covers
are heavy. Use both hands when removing them to avoid
dropping.

3 3/4" (9.5 cm)

Remove and Replace Refrigerator Doors

NOTE: Measure the width of your door opening to see whether or not you need to remove the refrigerator doors to move the refrigerator into your home. If door removal is necessary, see the following instructions.

IMPORTANT: If the refrigerator was previously installed and you are moving it out of the home, before you begin, turn the refrigerator control off. Unplug the refrigerator or disconnect power. Remove food and adjustable door or utility bins from doors.

Gather the required tools and read all instructions before removing doors. TOOLS NEEDED: TORX T25† screwdriver and a #2 Phillips screwdriver

WARNING

Electrical Shock Hazard

Disconnect power before removing doors.

Failure to do so can result in death or electrical shock.

Water Dispenser

Tubing Connection

A. Outer ring

Wiring Plug

Top Left Hinge

A.TORX T25 screws

B.Ground wire (Do not remove.)

C.Do not remove screws.

Top Right Hinge

A. TORX T25 screws

B. Hinge cover screw

C. Top hinge cover

D. Top hinge

Door at 90° Angle

to Cabinet°

90°

†TORX and T25 are trademarks of Acument Intellectual Properties, LLC.

WARNING

Excessive Weight Hazard

Use two or more people to move and install refrigerator.

Failure to do so can result in back or other injury.

Bottom Door Hinge

For your convenience, the refrigerator doors have bottom hinges with door closers. These closers allow the doors to swing fully closed with just a gentle push.

IMPORTANT: So that the closers feature will operate properly, the doors must be removed only when open to a 90° angle to the front of the cabinet. If one or both doors were not at a 90° angle when removed, the bottom door hinge must be reset.

90°

Reset the Door Hinge

1.Lift the door from the bottom hinge pin and place it on a flat surface.

2.Using a TORX T25 screwdriver, remove the bottom hinge with the bushing from the cabinet.

A.Bushing

B.Hinge base

3.Insert the bottom hinge and bushing into the corresponding slot in the bottom of the door.

NOTE: Make sure that the base of the hinge is parallel to the bottom of the door.

A.Hinge base parallel to the bottom edge of the door

4.Turn the hinge until the hinge base is at a 90° angle to the bottom edge of the door.

90°

A.Hinge base turned to a 90° angle with the bottom edge of the door

5.Remove the hinge from the door. Using a driver with a #2 square bit, reattach the bottom hinge to the refrigerator cabinet.

6.The hinge is now reset and prepared for the door to be replaced. See “Replace Refrigerator Doors” later in this section.

Remove Refrigerator Doors

WARNING

Electrical Shock Hazard Disconnect power before removing doors.

Failure to do so can result in death or electrical shock.

Remove Right-Hand Door

1.Unplug refrigerator or disconnect power.

2.Keep the refrigerator doors closed until you are ready to lift them free from the cabinet.

NOTE: Provide additional support for the refrigerator door while the hinges are being removed. Do not depend on the door gasket magnets to hold the door in place while you are working.

3.Using a Phillips screwdriver, remove the cover from the top hinge.

4.Using the TORX T25 screwdriver, remove the three screws from the top hinge and set aside.

A. Top hinge cover screw	C. TORX T25 screws
B. Top hinge cover	D. Top hinge

WARNING

Excessive Weight Hazard

Use two or more people to lift the refrigerator door. Failure to do so can result in back or other injury.

5.Open the door until it is at a 90° angle to the front of the cabinet.

6.Lift the refrigerator door from the bottom hinge pin. The top hinge will come away with the door.

Remove Left-Hand Door

IMPORTANT: The tubing and wiring for the water dispenser run through the left-hand door hinge, so they must be disconnected before removing the door.

1.Using a Phillips screwdriver, remove the cover from the top hinge.

A. Top hinge cover screw

B. Top hinge cover

2.Disconnect the water dispenser tubing located on top of the door hinge. Firmly pull up on the clasp. Then, pull the tubing out of the fitting.

NOTE: The water dispenser tubing remains attached to the left-hand refrigerator door.

3. Disconnect the wiring plug located on top of the door hinge.

■■ Grasp each side of the wiring plug. With your left thumb, press down to release the catch and pull the sections of the plug apart.

NOTE: Do not remove the green ground wire. It should remain attached to the door hinge.

4.Using the TORX T25 screwdriver, remove the three internal screws from the top hinge and set aside.

NOTE: Provide additional support for the refrigerator door while the hinges are being removed. Do not depend on the door gasket magnets to hold the door in place while you are working.

A.TORX T25 screws

B.Ground wire (Do not remove.)

5.Lift the refrigerator door from the bottom hinge pin. The top hinge will come away with the door.

NOTE: It may not be necessary to remove the bottom hinges and brake feet assemblies to move the refrigerator through a doorway.

■■ Only if necessary, use a TORX T25 screwdriver to remove

the bottom hinges and brake feet screws.

Replace Right-Hand Refrigerator Door

1.Set the right-hand door onto the bottom hinge pin.

2.Insert the top hinge pin into the open hole in the top of the refrigerator door.

3.Using the three TORX T25 screws, fasten the hinge to the cabinet. Do not tighten the screws completely.

Replace Left-Hand Refrigerator Door

IMPORTANT: Do not intertwine the water tubing and wiring bundles when reconnecting them.

1.Set the left-hand door onto the bottom hinge pin.

2.Using the three TORX T25 screws, fasten the hinge to the cabinet. Do not tighten the screws completely.

3.Reconnect the water dispenser tubing.

Insert the tubing firmly into the fitting until it stops. Close the clasp around the tubing. The clasp snaps into place between the fitting and the collar. Connect blue female side with blue male side and clasp. Repeat with gray female and gray male side.

4.Reconnect the electrical wiring.

■■ Push together the two sections of the wiring plug.

Final Steps

1.Completely tighten the five internal TORX T25 screws (three on the right-hand door hinge and two on the left-hand door hinge).

2.Replace both top hinge covers.

Remove and Replace

Freezer Drawer Fronts

Freezer Drawer

Remove Drawer Front

1.Open the freezer drawer to its full extension.

2.Loosen the two top screws that fasten the drawer front to the drawer glides. The two screws (one on the left-hand side and one on the right-hand side) are located inside the drawer front.

3.Remove the two screws at the bottom, inside the drawer front that fasten the drawer front to the drawer glides.

4.Lift up on the drawer front to release the screws from the drawer glide bracket slot.

A. Drawer glide bracket slots

Replace Drawer Front

1.Pull out the freezer drawer glides to their full extension.

2.Holding the drawer front by its sides, align the top screws, located at the bottom inside of the drawer front, with the drawer glide bracket slots.

NOTE: It helps if one person holds the drawer glides steady while another person aligns the drawer front and inserts the studs into the slots.

A.Drawer front screws

3.Tighten the two screws at the top of the drawer front (one on the left-hand side and one on the right-hand side) and replace the two screws on the bottom.

Final Steps

WARNING

Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

1.Plug into a grounded 3 prong outlet.

2.Reset the controls. See the “Using the Controls” section.

3.Return all removable parts and food to the drawers.

Electrical Requirements

WARNING

Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical connection.

If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person. Do not use a cord that shows cracks or abrasion damage along its length or at either the plug or connector end.

Recommended Grounding Method

A 115 V, 60 Hz, AC only 15 A or 20 A fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your refrigerator and approved accessories

be provided. Use an outlet that cannot be turned off by a switch. Do not use an extension cord.

IMPORTANT: If this product is connected to a GFCI (Ground Fault Circuit Interrupter) protected outlet, nuisance tripping of the power supply may occur, resulting in loss of cooling. Food quality and flavor may be affected. If nuisance tripping has occurred, and if the condition of the food appears poor, dispose of it.

NOTE: Before performing any type of installation or cleaning, turn off cooling, then disconnect the refrigerator from the electrical source. When you have finished, reconnect the refrigerator to

the electrical source and turn on cooling. See the “Using the Controls” section.

Water Supply Requirements

A cold water supply with water pressure between 35 and 120 psi (241 and 827 kPa) is required to operate the water dispenser and ice maker. If you have questions about your water pressure, call a licensed, qualified plumber.

NOTE: If the water pressure is less than what is required, the flow of water from the water dispenser could decrease or ice cubes could be hollow or irregular shaped.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of a reverse osmosis system going to the water inlet valve of the refrigerator needs to be between 35 and 120 psi (241 and 827 kPa).

If a reverse osmosis water filtration system is connected to your cold water supply, the water pressure to the reverse osmosis system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

■■ Check to see whether the sediment filter in the reverse osmosis system is blocked. Replace the filter if necessary.

■■ Allow the storage tank on the reverse osmosis system to refill after heavy use. The tank capacity could be too small to keep up with the requirements of the refrigerator.

NOTE: Faucet-mounted reverse osmosis systems are not recommended.

■■ If your refrigerator has a water filter, it may further reduce the water pressure when used in conjunction with a reverse osmosis system. Remove the water filter. See the “Water Filtration System” section.

If you have questions about your water pressure, call a licensed, qualified plumber.

Connect the Water Supply

Read all directions before you begin.

IMPORTANT:

■■ Connect to potable water supply only.

Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.

■■ Plumbing must be installed in accordance with the International Plumbing Code and any local codes and ordinances.

■■ Copper and PEX tubing connections from the household water line to the refrigerator are acceptable and will help avoid off-taste or odor in your ice or water. Check for leaks.

If PEX tubing is used instead of copper, we recommend the following Part Numbers: W10505928RP (7 ft [2.14 m] jacketed PEX), 8212547RP (5 ft [1.52 m] PEX), or W10267701RP

(25 ft [7.62 m] PEX).

■■ Install tubing only in areas where temperatures will remain above freezing.

Tools Needed:

Gather the required tools and parts before starting installation. ■■ Flat-blade screwdriver

■■ 7/16" and 1/2" open-end wrenches or two adjustable wrenches

■■ 1/4" nut driver

NOTE: Do not use a piercing-type or 3/16" (4.76 mm) saddle valve which reduces water flow and clogs easier.

Connect to Water Line

IMPORTANT: If you turn the refrigerator on before the water is connected, turn off the ice maker.

1.Unplug refrigerator or disconnect power.

2.Turn off main water supply. Turn on nearest faucet long enough to clear line of water.

3.Use a quarter-turn shut-off valve or the equivalent, served by a 1/2" (12.7 mm) household supply line.

NOTE: To allow sufficient water flow to the refrigerator, a minimum 1/2" (12.7 mm) size household supply line is recommended.

A. Sleeve	C. Copper tubing (to refrigerator)
B. Nut	D. Household supply line (1/2" [12.7 mm] minimum)

4.Now you are ready to connect the copper tubing to the shut-off valve. Use 1/4" (6.35 mm) O.D. (outside diameter) soft copper tubing to connect the shut-off valve and the refrigerator.

■■ Ensure that you have the proper length needed for the job. Be sure both ends of the copper tubing are cut square.

■■ Slip compression sleeve and compression nut onto copper tubing as shown. Insert end of tubing into outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjustable wrench. Do not overtighten.

A. Compression sleeve C. Copper tubing

B.Compression nut

5.Place the free end of the tubing into a container or sink and turn on main water supply to flush out tubing until water is clear. Turn off shut-off valve on the water pipe.

NOTE: Always drain the water line before making the final connection to the inlet of the water valve to avoid possible water valve malfunction.

6.Bend the copper tubing to meet the water line inlet which is located on the back of the refrigerator cabinet as shown. Leave a coil of copper tubing to allow the refrigerator to be pulled out of the cabinet or away from the wall for service.

Connect to Refrigerator

Follow the connection instructions specific to your model.

1.Remove plastic cap from water valve inlet port. Attach the copper tubing to the valve inlet using a compression nut and sleeve as shown. Tighten the compression nut. Do not overtighten. Confirm copper tubing is secure by pulling on copper tubing.

2.Create a service loop with the copper tubing. Avoid kinks when coiling the copper tubing. Secure copper tubing to refrigerator cabinet with a “P” clamp.

Complete the Installation

WARNING

Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

1.Plug into a grounded 3 prong outlet.

2.Flush the water system. See “Water and Ice Dispensers” section.

NOTE: Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced. Allow three days to completely fill the ice storage bin.

Handle Installation and Removal

Parts Included: refrigerator door handles (2), refrigerated drawer handles (2), freezer drawer handle (1), 1/8" and 3/32" hex keys, spare setscrew(s)

NOTE: The freezer drawer handle is shorter than the refrigerator door handles. Handle style may vary by model.

Install Handles

Knob Assembly

IMPORTANT: Make sure to put together the knob assembly prior to assembling the handle.

1.Remove the handles and knob assembly from the packaging inside the refrigerator and place them on a soft surface.

2.Align the knob assembly with the lever at the middle of the door.

3.Fully engage the knob assembly onto the lever.

4.While holding the knob assembly, insert the short end of the 3/32" hex key into the hole and slightly rotate the hex key until the key is engaged in the setscrew.

5.Using a clockwise motion, tighten the setscrew just until the setscrew begins to contact the lever. Fully tighten.

A. Copper tubing	C. Compression nut
B. “P” clamp	D. Compression sleeve

3.Turn on water supply to refrigerator and check for leaks. Correct any leaks.

Refrigerator Doors

NOTE: Handle mounting setscrews are preinstalled inside the handle.

1.Remove the handles from the packaging inside the refrigerator and place them on a soft surface.

2.Open a refrigerator compartment door. On the closed door, place a handle onto the shoulder screws so that the setscrews are facing the adjacent door.

A.Shoulder screws

B.Setscrews inside the handle

3.Firmly push the handle toward the door until the handle base is flush against the door.

4.While holding the handle, insert the short end of the hex key into the upper hole and slightly rotate the hex key until it is engaged in the setscrew.

5.Using a clockwise motion, tighten the setscrew just until it begins to contact the shoulder screw. Do not fully tighten.

6.Repeat steps 4 and 5 to fasten the lower setscrew.

7.Once both setscrews have been partially tightened as instructed in the previous steps, fully tighten both setscrews.

IMPORTANT: When the screws feel tight, tighten them an additional quarter turn. The handle is not properly installed without this extra tightening.

8.Repeat steps 2 through 7 to install the other handle onto the adjacent refrigerator door.

Freezer Drawer

1.With the drawer closed, place the handle onto the shoulder screws so that the setscrews are facing down toward the floor.

A.Shoulder screw

B.Setscrews inside the handle

2.Firmly push the handle toward the drawer until the handle base is flush against the drawer.

3.Insert the short end of the hex key into the left-hand hole and slightly rotate the hex key until it is engaged in the setscrew.

4.Using a left-to-right motion, tighten the setscrew a quarter turn at a time just until it begins to contact the shoulder screw. Do not fully tighten.

5.Repeat steps 3 and 4 to fasten the right-hand setscrew to the shoulder screw.

6.Once both setscrews have been partially tightened as instructed in the previous steps, fully tighten both setscrews.

IMPORTANT: When the screws feel tight, tighten them an additional quarter turn. The handle is not properly installed without this extra tightening.

7.Save the hex key and all instructions.

Remove the Handles

1.While holding the handle, insert the short end of the hex key into a setscrew hole and slightly rotate the hex key until it is engaged in the setscrew.

2.Using a right-to-left motion, loosen the setscrew a quarter turn at a time.

3.Repeat steps 1 and 2 for the other setscrew. Slowly pull the handle away from the door or drawer.

4.If necessary, use a Phillips screwdriver to remove the shoulder screws from the door.

Remove and Replace Handle Medallions (optional)

The handles for your model have red medallions on the ends. Replacement medallions are available for purchase. See “Accessories” to order.

1.Using a 1/8" hex key, remove the medallion from the end of the handle.

2.Replace medallion.

3.Using the fastener removed in Step 1, attach the medallion to the handle.

A. Handle medallion

Refrigerator Leveling

and Door Closing

The base grille covers the adjustable brake feet and roller assemblies located at the bottom of the refrigerator below the freezer drawer. Before making any adjustments, remove the base grille and move the refrigerator to its final location.

Tools Needed: 1/4" hex driver

Tools Provided: 1/4" hex key

1.Use a 1/4" hex nut driver to remove both screws in base grille.

2.Remove the base grille. Using both hands, grasp the grille firmly and pull it toward you. Open the freezer drawer to access the brake feet.

NOTE: To allow the refrigerator to roll easier, raise the brake feet by turning them counterclockwise. The front rollers will be touching the floor.

3.Move the refrigerator to its final location.

4.Using the 1/4" hex driver, lower the brake feet. Turn them clockwise until the rollers are off the floor and both brake feet are snug against the floor. This keeps the refrigerator from rolling forward when opening the refrigerator doors or freezer drawer.

IMPORTANT: If you need to make further adjustments involving the brake feet, you must turn both brake feet the same amount to keep the refrigerator level.

5.Use a level to make sure the refrigerator is level from side to side and front to back.

6.Make sure the doors are even at the top and that the space between the bottom of the refrigerator doors and the top of the freezer drawer is even. If necessary, align the doors.

To Align the Doors:

■■ Keeping both refrigerator doors closed, pull out the freezer drawer. Locate the bottom hinge pin of the right-hand refrigerator door. The alignment screw is inside the bottom hinge pin.

■■ Insert the short end of the 1/8" hex key wrench (packed with the Door Handle Installation Instructions) into the bottom hinge pin until it is fully engaged in the alignment screw.

To raise the refrigerator door, turn the hex key to the right. To lower the door, turn the hex key to the left.

■■ Continue to turn the alignment screw until the doors are aligned.

A.Bottom hinge pin

B.1/8" hex key wrench

7.Make sure the refrigerator is steady. If the refrigerator seems unsteady or rolls forward when a door or drawer is pulled open, adjust the brake feet.

To Steady the Refrigerator:

■■ Open the freezer drawer. Using a 1/4" hex driver, turn both brake feet clockwise the same amount until the brake feet are snug against the floor. Check again. If not satisfied, continue to adjust the brake feet by half turns of the screw until the refrigerator does not roll forward when the drawer is opened.

NOTE: Having someone push against the top of the refrigerator takes some weight off the brake feet. This makes it easier to turn the screws.

8.Replace the base grille by aligning the ends of the grille with the leveling assemblies on each side and snapping the grille into place. Use a 1/4" hex nut driver to reinstall screws.

FILTERS AND ACCESSORIES

Water Filtration System

Replace and Install the Water Filter

The water filter should be replaced every six months based on a flow rate of .50 gpm—.60 gpm (1.89 - 2.27 lpm) that filters

200 gallons (757.1 L) of water.

To order a replacement filter, contact us. See “Accessories” section in the User Guide for information on ordering.

NOTE: If the filter is not installed correctly, water may dispense at a lower flow rate and there will be slower ice production. Improper filter installation may also cause the water filter housing to leak.

1.Push the water filter door to open, located bottom left of refrigerator compartment.

2. Twist the water filter and turn 90° counterclockwise to unlock.

4. Remove the water filter cap from the water filter.

5.Install the water filter cap onto the new filter. Be sure to align the arrows so the groves in filter align with ribs in filter cap.

6. Insert the filter into the housing.

7.Twist the water filter and turn 90° clockwise until it locks into place and that arrows are aligned.

3. Pull the filter out of the housing.

8. Push the water filter door closed.

The Water Filter Status Light

The water filter status lights will help you know when to change your water filter.

■■ Order Filter (yellow): It is almost time to change the water filter. “Order Filter” display is on all of the time but off in Showroom mode and Sabbath mode.

■■ Replace Filter (red): Replace the water filter. While you are dispensing water, “Replace Filter” icon will flash constantly from the beginning to the end of dispensing. After 14 days without replacing the Water Filter, the “Replace Filter” icon will blink seven times and an alert tone will sound three times at the end of dispensing.

■■ Reset Filter: Touch MAX COOL and MAX ICE together for

3 seconds to reset water filter. The display will do a 3-second countdown, then flash the icon and play a tone.

Install Air Filter

An air filter is 15 times more powerful than baking soda at reducing common food odors inside the refrigerator.

On some models, your refrigerator’s accessory packet includes an air filter which must be installed prior to use.

Installing the Air Filter

Install the air filter behind the blue LED-lighted vent cover, located on the rear wall near the middle of the refrigerator.

1.Remove the air filter from its packaging.

2.Firmly grasp plastic cover on the vented cover with both hands and pull out to remove.

NOTE: When cover is removed for the first time, a small foam part the size of the filter will need to be discarded.

3. Snap the filter into place.

A. Air filter

Replacing the Air Filter

The disposable air filter should be replaced every 6 months.

To order a replacement air filter, contact us. See “Accessories” section in the User Guide for information on ordering.

1.Remove the used air filter by squeezing in on the side tabs.

2.Install the new air filter following the instructions in the previous sections.

Install Produce Preserver

(on some models)

The produce preserver absorbs ethylene to slow the ripening process of many produce items. As a result, certain produce items will stay fresh longer.

Ethylene production and sensitivity varies, depending on the type of fruit or vegetable. To preserve freshness, it is best to separate produce with sensitivity to ethylene from fruits that produce moderate-to-high amounts of ethylene.

	Sensitivity	Ethylene
	to Ethylene	Production

Apples	High	Very High

Asparagus	Medium	Very Low

Berries	Low	Low

Broccoli	High	Very Low

Cantaloupe	Medium	High

Carrots	Low	Very Low

Citrus Fruit	Medium	Very Low

Grapes	Low	Very Low

Lettuce	High	Very Low

Pears	High	Very High

Spinach	High	Very Low

Installing the Produce Preserver

For your convenience, the suction-mounted produce preserver can be installed in either the crisper or the refrigerated drawers.

CAUTION: IRRITANT

MAY IRRITATE EYES AND SKIN. DANGEROUS FUMES FORM WHEN MIXED WITH OTHER PRODUCTS.

Do not mix with cleaning products containing ammonia, bleach or acids. Do not get in eyes, on skin or clothing. Do not breathe dust. Keep out of reach of children.

FIRST AID TREATMENT: Contains potassium permanganate. If swallowed, call a Poison Control Center or doctor immediately. Do not induce vomiting. If in eyes, rinse with water for 15 minutes. If on skin, rinse with water.

1.Wash the interior of a drawer with a solution of mild dish soap and warm water and dry thoroughly.

2.Find the package containing the Produce Preserver inside the refrigerator and install the Produce Preserver into the drawer according to the instructions provided in the package.

Replacing the Produce Preserver

The disposable packet(s) should be replaced every 6 months or when the status indicator changes completely from white to red.

To order replacements, contact us. See the “Accessories” section for information on ordering.

1.Remove the used packets from the produce preserver housing.

2.Remove the used status indicator.

3.Install the replacement packets and status indicator using the instructions included in the package.

Accessories

The following accessories are available for your refrigerator. To order an accessory, contact us and ask for the part number.

In the U.S.A., visit our website www.kitchenaid.com or call

1-800-422-1230.

In Canada, visit our webpage www.kitchenaid.ca or call

1-800-807-6777.

Affresh® Stainless Steel Cleaner:

In U.S.A., order Part #W10355016 In Canada, order Part #W10355016B

Affresh® Stainless Steel Wipes:

In U.S.A., order Part #W10355049 In Canada, order Part #W10355049B

Affresh® Kitchen & Appliance Cleaner:

In U.S.A., order Part #W10355010 In Canada, order Part #W10355010B

Water Filter:

In U.S.A., order Part #EDR2RXD1 In Canada, order Part #EDR2RXD1B

Air Filter:

Order Part #W10311524 or AIR1

Produce Preserver Starter kit:

Order Part #P1UB6S1

Produce Preserver Refill kit:

Order Part #P1KC6R1

Door Handle Medallions:

Order Part #W10762987 (Black)

Order Part #W10762993 (Chrome)

REFRIGERATOR USE

Opening and Closing Doors

There are two refrigerator compartment doors. The doors can be opened and closed either separately or together. There is a vertically hinged seal on the left refrigerator door.

■■ When the left-side door is opened, the hinged seal automatically folds inward so that it is out of the way.

■■ When both doors are closed, the hinged seal automatically forms a seal between the two doors.

A. Hinged seal

Door-within-Door

Use the hidden latch and left up to open the door-within- door and get instant access to items and ingredients in your refrigerator door bins

IMPORTANT: Do not open inner door when outer door is open. Close outer door before opening inner door.

In-door Venting

The in-door venting will direct cold air in the lower door bin area. Opening the shutter door (sliding it right) will make this area colder, while closing the shutter door (sliding it left) will make it less cold. This will keep milk and beverages at the right temperature.

The refrigerator compartment door switch is located in the top left and right hinge cover.

■■ The door switch uses magnet to sense door opening/closing.

■■ Ensure there are no magnet or electronic devices (Speaker, CoolVox®, etc) within 3 inches of the hinge cap.

NOTE: The light and internal user interface (UI) will not turn on if the door opening is not detected.

Using the Controls

The Temperature Control UI is located above the external dispenser and on the side of the left refrigerator door.

Viewing and Adjusting Temperature Set Points

For your convenience, your refrigerator and freezer controls are preset at the factory.

When you first install your refrigerator, make sure that the controls are still set to the recommended set points. The factory recommended set points are 37°F (3°C) for the refrigerator and 0°F (-18°C) for the freezer.

IMPORTANT:

■■ Wait 24 hours before you put food into the refrigerator. If you add food before the refrigerator has cooled completely, your food may spoil.

NOTE: Adjusting the set points to a colder-than- recommended setting will not cool the compartments any faster.

■■ If the temperature is too warm or too cold in the refrigerator or freezer, first check the air vents to be sure they are not blocked before adjusting the controls.

■■ The recommended settings should be correct for normal household use. The controls are set correctly when milk or juice is as cold as you like and when ice cream is firm.

NOTE: Areas such as a garage, basement, or porch may have higher humidity or extreme temperatures. You may need to adjust the temperature away from the recommended settings to accommodate for these conditions.

■■ Wait at least 24 hours between adjustments. Recheck the temperatures before other adjustments are made.

View Temperature Set Points

1.Touch —/+ for Refrigerator or —/+ for Freezer and toggle through temperature set points.

NOTE: To view temperature in degrees Celsius, touch and hold the °F/°C button for 3 seconds and the temperature display will change. To return to Fahrenheit, touch and hold the °F/°C for 3 seconds and the temperature display will change.

To activate Temperature mode for Drawer, touch DRAWER and toggle through four optional temperature settings: Meat - Fish, Cold Drinks, Deli - Cheese, and Wine. The display will show the temperature set point of the selected setting for the drawer.

Recommended Refrigerator Temperature

Recommended Freezer Temperature

Adjust Temperature Set Points

Refrigerator set-point range: 33°F to 45°F (1°C to 7°C) Freezer set point range: -6°F to 5°F (-22°C to -15°C)

1.Touch —/+ to adjust the Refrigerator zone. The display will show the temperature set point of the selected compartment as shown.

2.When the temperature in is the range of Extend-Freeze™, the display will light up. Extend-Freeze™ is activated at the coldest Freezer set point.

When adjusting temperature set points, use the following chart as a guide:

CONDITION:	TEMPERATURE ADJUSTMENT:

Refrigerator too cold	Refrigerator setting 1° higher

Refrigerator too warm	Refrigerator setting 1° lower

Freezer too cold	Freezer setting 1° higher

Freezer too warm/	Freezer setting 1° lower
too little ice


Extend-Freeze™

This feature acts on the most-relevant storage parameters that must be controlled to minimize moisture migration from frozen food. This in turn reduces the freezer burn occurrence.

To turn on the Extend-Freeze™ feature, toggle to the coldest Freezer temperature set point.

To turn off the Extend-Freeze™ feature, toggle from the coldest freezer set point to any other temperature.

Max Cool

The Max Cool feature assists with periods of high refrigerator use, full grocery loads, or temporarily warm room temperatures.

■■ To turn on the Max Cool feature, press the MAX COOL button. When the button is pressed, the icon will blink three times and appear on the display screen.

■■ To manually turn off the Max Cool feature, press the MAX COOL button and the display will blink three times and turn off. The Max Cool feature will remain on for 24 hours unless manually turned off. Adjusting the refrigerator temperature will automatically turn off the Max Cool feature.

NOTE: Setting the freezer to a colder temperature may make some foods, such as ice cream, harder.

Max Ice

The Max Ice feature assists with increasing the cooling for the freezer compartment in order to increase ice production.

■■ To turn on or off the Max Ice feature, press the MAX ICE button. When the button is pressed to turn the feature on, the icon will blink three times and appear on the display screen.

■■ To manually turn off the Max Ice feature, press the MAX ICE button and the display will blink three times and turn off. The Max Ice feature will remain on for 24 hours unless manually turned off. Adjusting the freezer temperature will automatically turn off the Max Ice feature.

NOTE: Setting the freezer to a colder temperature may make some foods, such as ice cream, harder.

Water Filter Reset

Displays the status of the water filter. To reset the water filter, press MAX ICE and MAX COOL for 3 seconds. After countdown, the Good icon will blink three times and remain lit.

NOTE: The water filter status lights on the internal controls will let you know when to change your water filter.

■■ ORDER FILTER (yellow): Order a replacement water filter.

■■ REPLACE FILTER (red): Replace the water filter. While you are dispensing water, Replace Filter icon will flash constantly from beginning to the end of dispensing. After 14 days without replacing the water filter, the Replace Filter icon will blink seven times and an alert tone will sound three times, at the end of dispensing. See the “Water Filtration System” section.

NOTE: REPLACE FILTER will remain illuminated if a filter reset is not done.

■■ RESET FILTER: Touch MAX ICE and MAX COOL at the same time on the temperature control display for 3 seconds to reset water filter. The display will do a 3-second countdown and then flash the icon and play a tone.

Energy Saver

Your refrigerator will turn off the vertical mullion heater and dispenser heater when Energy Saver is enabled.

■■ To turn Energy Saver on, press and hold the ENERGY SAVER button for 3 seconds. The Energy Saver icon will blink three times and then remain lit as shown.

IMPORTANT: When Energy Saver is enabled and the LED is on, the dispenser heater and vertical mullion heater will be turned off.

■■ Press and hold ENERGY SAVER for 3 seconds again to turn the heaters back on.

Sound On/Off

The Sound button allows the customer to turn the sound on and off.

■■ To turn on the Sound feature, press the SOUND button. When the button is pressed, the Sound icon will blink three times and appear on the display screen.

■■ To manually turn off the Sound feature, press the SOUND button and the display will blink three times and turn off.

Power Outage

The Power Outage indicator lets you know if the power supply to the refrigerator has been off and the freezer temperature has risen.

The control panel display will read “Power Outage” and an alert tone will sound three times. Touch any button to stop the tone and turn off the Power Outage icon.

Once the power outage has been confirmed, “Power Outage,” will disappear.

Showroom Mode

This mode is used when the refrigerator is on display in a retail store or if you want to turn the cooling off and deactivates all other functions (except interior lighting). Showroom mode can be used when going on vacation, see “Vacation and Moving Care” section for proper steps on leaving your refrigerator in this mode for long periods of time.

If you turn on Showroom mode, “Showroom” will light up on the display. Enter or exit Showroom mode by pressing and holding °F/°C and DRAWER at the same time for 3 seconds.

NOTE: Empty ice maker if refrigerator is going to be turned off for an extended period of time.

Sabbath Mode

Sabbath mode is designed to have all the benefits of saving even more energy, yet maintaining food freshness. The freezer and refrigerator user set points remain unchanged while in this mode. If you unintentionally turn on Sabbath mode, “Sabbath” will light up on the display. Enter and exit Sabbath mode by pressing and holding °F/°C and SOUND at the same time for

3 seconds.

NOTE: You will be unable to dispense or change temperature set points in Sabbath mode. Your interior lighting and control panels will all be inactive in Sabbath mode.

External Dispenser Controls

The Dispenser UI is located above the external dispenser of the refrigerator.

IMPORTANT: The display screen on the dispenser control panel will turn off automatically and enter “sleep” mode when the control buttons and dispenser paddles have not been used for 2 minutes or more. Touch any control button to reactivate the display screen.

Additional Features

Door Ajar Alarm

The Door Ajar Alarm feature sounds an alarm when the refrigerator door(s) or freezer drawer is open for 5 minutes and cooling is turned on. The alarm will repeat every 2 minutes. Close all doors and drawer to turn it off.

NOTE: To mute the audible alarm while keeping the doors open, such as while cleaning the inside of the refrigerator, touch any button on the control panel. The alarm sound will be temporarily turned off, but the Door Ajar icon will still be displayed on the dispenser control panel.

Lighting the Refrigerator

The refrigerator has an interior light that comes on any time the door is opened.

NOTE: The light is an LED which does not need to be replaced. If the LED does not illuminate when the door is opened, call Service to replace the light. See “Assistance or Service” in the “Warranty” section for contact information.

2.Release the dispenser paddle for 5 seconds. Repeat steps 1 and 2 until water begins to flow.

3.Once water begins to flow, continue depressing and releasing the dispenser pad (5 seconds on, 5 seconds off) until a total of 3 gal (12 L) has been dispensed.

Calibrate Measured Fill

Household water pressure may affect the accuracy of the Measured Fill feature. So, for optimum performance of your water dispenser, you must first calibrate Measured Fill.

IMPORTANT:

■■ Flush the water system before calibrating Measured Fill.

■■ For best results, calibration should be performed when water is not being used in the house.

1.Place a sturdy measuring cup (1-cup [237 mL] size) on the dispenser tray centered in front of the ice/water dispenser paddle.

NOTE: Depending on your model, a measuring cup may be provided.

Water and Ice Dispensers

IMPORTANT:

■■ Allow 3 hours for the refrigerator to cool down and chill water.

■■ Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced.

■■ The dispensing system will not operate if the left-hand refrigerator door is open.

A.Water dispenser paddle

B.Ice dispenser paddle

Flush the Water System

Air in the water dispensing system can cause the water dispenser to drip. After connecting the refrigerator to a water source or replacing the water filter, flush the water system.

Flushing the water dispensing system forces air from the water line and filter and prepares the water filter for use. Additional flushing may be required in some households.

NOTE: As air is cleared from the system, water may spurt out of the dispenser.

1.Using a sturdy container, depress and hold the water dispenser paddle for 5 seconds.

A.Water dispenser paddle

B.Ice dispenser paddle

C.Measuring cup (1cup [237 mL])

Ensure that you do not have any Measured Fill preset selected.

2.Touch and hold the Measured Fill button for 3 seconds to enter into Calibration mode. The Calibration and Measured Fill icons will illuminate and remain lit while the Measured Fill feature is being calibrated.

NOTE: You may touch MEASURED FILL to exit at any time in Calibration mode. The Calibration icon will disappear and the display will return to the Home screen.

3.Press and hold the water dispenser paddle, as needed, to dispense water to the 1-cup (237 mL) fill line in the measuring cup.

NOTE: If overfilling or spilling occurs, discard the water and restart the calibration process.

4.When 1 cup (237 mL) of water has been correctly dispensed into the measuring cup, touch MEASURED FILL to confirm the calibration.

5.When Measured Fill calibration has been confirmed, the Calibration icon will disappear and the display will return to the home screen.

Save Favorite Fill

Household water pressure may affect the accuracy of the Favorite Fill feature. So, for optimum performance of your water dispenser, you must first calibrate Measured Fill. (See Measured Fill section).

NOTE: Water will not be dispensed using the Favorite Fill feature unless your preferred Favorite Fill amount is saved first.

IMPORTANT:

■■ Flush the water system before using Favorite Fill.

■■ For best results, calibration should be performed when water is not being used in the house.

1.Place a preferred-size cup on the dispenser tray centered in front of the ice/water dispenser paddle.

2.Select either Favorite 1 or Favorite 2, and then touch and hold the Favorite Fill button for 3 seconds to enter into Saving mode. The Favorite Fill icon will illuminate and remain lit while the Favorite Fill feature is being saved.

NOTE: You may touch FAVORITE FILL to exit at any time in Saving mode and the display will return to the Home screen.

3.Press and hold the water dispenser paddle, as needed, to dispense water to the preferred-size cup.

NOTE: If overfilling or spilling occurs, discard the water and restart the saving process.

4.When the preferred amount of water has been correctly dispensed into the cup, touch the FAVORITE FILL button to confirm the favorite amount.

5.When Favorite Fill amount has been confirmed, the display will return to the home screen.

Dispensing

Touch CUBED ICE or CRUSHED ICE for your ice selection.

NOTES:

■■ For crushed ice, cubes are crushed before being dispensed. This may cause a slight delay when dispensing crushed ice. Noise from the ice crusher is normal and pieces of ice may vary in size.

■■ When changing from crushed to cubed, a few ounces of crushed ice will be dispensed along with the first cubes.

Dispensing Water

IMPORTANT:

■■ Dispense at least 1 qt (1 L) of water every week to maintain a fresh supply.

■■ If the flow of water from the dispenser decreases, it could be caused by low water pressure.

■■ With the water filter removed, dispense 1 cup (237 mL) of water. If 1 cup (237 mL) of water is dispensed in 8 seconds or less, the water pressure to the refrigerator meets the minimum requirement.

■■ If it takes longer than 8 seconds to dispense 1 cup (237 mL) of water, the water pressure to the refrigerator is lower than recommended. See the “Water Supply Requirements” and “Troubleshooting” sections for suggestions.

To Dispense Water — Standard:

1.Press a sturdy glass against the water dispenser paddle.

2.Remove the glass to stop dispensing.

NOTE: The Dispense Water button does not enable standard dispensing. It only functions in Measured Fill mode.

To Dispense Water — Measured Fill:

Measured Fill allows you to dispense a specified amount of water with the touch of a few buttons.

1.Put a sturdy glass under waterspout. Touch MEASURED FILL to activate.

NOTE: The amount of water you select will be dispensed. Make sure the container can hold the entire volume. If ice is in the container, you may need to adjust your selection.

2.Touch MEASURED FILL to turn on, then touch to select

8 oz (0.2 L), 16 oz (0.5 L), or 24 oz (0.7 L). Touch the fourth time to exit Measured Fill display.

3.Touch DISPENSE WATER or press paddle and the selected amount of water will be dispensed.

NOTES:

■■ The Measured Fill dispenser will automatically time out after 1 minute of inactivity.

■■ You can refill several glasses with the same measurement

by continuing to touch DISPENSE WATER after each glass fill. Measured Fill options are listed in the following chart:

Units

Ounces	8	16	24

Cups	1	2	3

Liters	0.2	0.5	0.7

NOTE: Most coffee cups (commonly 4 to 6 oz [118 to 177 mL] per cup) are not the same size as a measuring cup

(8 oz [237 mL]). You may need to recalibrate Measured Fill to underfill or to avoid unintentionally overfilling coffee cups.

4.Dispense water.

NOTE: While dispensing water, the flow of water will automatically stop once the desired volume has been dispensed.

■■ Press a sturdy glass against the dispenser paddle below the waterspout.

■■ Place the glass below the waterspout and touch DISPENSE WATER for hands-free dispensing.

5.To pause dispensing before the selected volume has been dispensed, touch DISPENSE WATER a second time or touch the water dispenser paddle. Touch DISPENSE WATER or paddle again to resume dispensing remaining amount.

NOTE: If you stop dispensing before the desired volume has been dispensed, the display will turn off after 1 minute. If you have not resumed by then, it will reset back to the original amount.

6.To select a new volume or start dispensing the same volume again, you must first finish dispensing the selected volume or turn off the Measured Fill feature (either by waiting 1 minute so it will automatically turn off or by touching CUBED ICE

or CRUSHED ICE to manually turn it off), and then select MEASURED FILL again.

To Dispense Water — Favorite Fill:

Favorite Fill allows you to dispense a preferred amount of water with the touch of a few buttons.

1.Put a sturdy glass under waterspout. Touch FAVORITE FILL to activate.

NOTE: The amount of water you select will be dispensed. Make sure the container can hold the entire volume. If ice is in the container, you may need to adjust your selection.

2.Touch FAVORITE FILL to turn on, then touch to select Favorite 1 or Favorite 2. Touch the third time to exit Favorite Fill display.

3.Touch DISPENSE WATER or press paddle and the selected amount of water will be dispensed.

NOTES:

■■ The Favorite Fill dispenser will automatically time out after 1 minute of inactivity.

■■ You can refill several glasses with the same measurement by continuing to touch DISPENSE WATER after each glass fill.

4.Dispense water.

NOTE: While dispensing water, the flow of water will automatically stop once the desired volume has been dispensed.

■■ Press a sturdy glass against the dispenser paddle below the waterspout.

■■ Place the glass below the waterspout and touch DISPENSE WATER for hands-free dispensing.

NOTE: If you stop dispensing before the desired volume has been dispensed, the display will turn off after 1 minute. If you have not resumed by then, it will reset back to the original amount.

6.To select a new volume or start dispensing the same volume again, you must first finish dispensing the selected volume or turn off the Favorite Fill feature (either by waiting 1 minute so it will automatically turn off or by touching CUBED ICE or CRUSHED ICE to manually turn it off), and then select FAVORITE FILL again.

The Ice Dispenser

IMPORTANT:

■■ If the ice cubes are hollow or have an irregular shape, it could be because of low water pressure. See the “Water Supply Requirements” section.

■■ Ice travels from the ice storage bin through the dispenser chute to the dispenser. To turn off the ice maker, see the “Ice Maker and Storage Bin” section.

■■ The dispenser may continue to make noise and ice may continue to dispense for several seconds after releasing the dispenser button or paddle.

To Clean the Ice Dispenser Chute:

Humidity causes ice to naturally clump together. Ice particles can build up until the ice dispenser chute becomes blocked.

If ice is not dispensed regularly, it may be necessary to empty the ice storage bin and clean the ice delivery chute, the ice storage bin, and the area beneath the storage bin every 2 weeks.

■■ If necessary, remove the ice clogging the storage bin and delivery chute using a plastic utensil.

■■ Clean the ice delivery chute and the bottom of the ice storage bin using a warm, damp cloth, and then dry thoroughly.

To Dispense Ice:

Paddle Dispensing

1.Select the desired type of ice by pressing CUBED ICE or CRUSHED ICE.

WARNING

Cut Hazard

Use a sturdy glass when dispensing ice.

Failure to do so can result in cuts.

2.Press a sturdy glass against the dispenser paddle. Hold the glass close to the dispenser opening, so ice does not fall outside of the glass.

IMPORTANT: You do not need to apply a lot of pressure to the paddle to activate the ice dispenser. Pressing hard will not make the ice dispense faster or in greater quantities.

3.Remove the glass to stop dispensing.

NOTE: Ice may continue to dispense for several seconds after removing the glass from the dispenser paddle. The dispenser may continue to make noise for a few seconds after dispensing.

The Dispenser Drip Tray

The drip tray can be removed to carry to the sink to empty or clean.

■■ Lift up on the front edge of the tray and pull forward to remove.

■■ The drip tray can also slide out to assist in Measured/Favorite Fill.

The Dispenser Light

1.When you use the dispenser, the light will automatically turn on.

2.The dispenser light also serves as an automatic nightlight. Once the ambient light in the room is reduced, the auto sensor will cause the dispenser light to illuminate.

The Dispenser Lock

The dispenser can be locked for easy cleaning or to avoid unintentional dispensing by small children and pets.

NOTE: The lock feature does not shut off power to the refrigerator or the dispenser light. It simply deactivates the controls and dispenser levers. To turn off the ice maker, see the “Ice Maker and Storage Bin” section.

■■ Touch and hold CUBED ICE for 3 seconds to lock the dispenser.

■■ Touch and hold CUBED ICE for 3 seconds to unlock the dispenser.

■■ The display screen indicates when the dispenser is locked.

Ice Maker and Storage Bin

IMPORTANT: To avoid low ice production and poor quality ice, flush the water system before turning on the ice maker. See the “Water and Ice Dispensers” section.

■■ Following installation, allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced. Allow 2 to 3 days to fill the ice storage bin.

■■ The quality of your ice will be only as good as the quality of the water supplied to your ice maker. Avoid connecting the ice maker to a softened water supply. Water softener chemicals (such as salt) can damage parts of the ice maker and lead to poor quality ice. If a softened water supply

cannot be avoided, make sure the water softener is operating properly and is well-maintained.

■■ If the ice in the storage bin clumps together, break up ice using a plastic utensil and discard ice. Do not use anything sharp to break up the ice. This can cause damage to the ice bin and the dispenser mechanism.

■■ Do not store anything in the ice storage bin.

Style 1: Ice Maker in the Refrigerator

The ice maker is located on the left door behind the bins. Ice cubes are ejected into the ice storage bin located on the lefthand refrigerator door.

Turn the Ice Maker On/Off

1.Push up on the latch on the left-hand side of the ice compartment to open the door.

2.Turn on the ice maker by moving the switch to the On (I) position.

NOTES:

■■ To manually turn off the ice maker, move the control to the Off (O) position.

■■ Your ice maker has an automatic shutoff. The sensor will automatically stop ice production if the storage bin is full, if the door is open, or the storage bin is removed. The control will remain in the On (I) position.

3. Close the ice compartment door.

Remove and Replace the Ice Storage Bin

■■ Remove the ice storage bin by inserting your fingers into the hole at the base of the bin and pulling the latch to release the bin from the compartment. Lift the storage bin up and pull it straight out.

■■ Replace the storage bin inside the ice compartment and push down to make sure it is firmly in place.

Ice Production Rate

■■ The ice maker should produce approximately 3 lbs (1.4 kg) of ice per day under normal operation.

■■ To increase ice production, select the Max Ice feature from the control panel. See the “Using the Controls” section.

Style 2: Ice Maker in the Freezer (on some models)

Turn the Ice Maker On/Off

To turn off the second ice maker, press and hold FREEZER

—/+ for 3 seconds. The display will countdown to 3,2,1 and turn off the ice maker.

The 2nd Ice Off icon will blink three times and then stay on at 100% brightness.

To turn on the second ice maker, press and hold —/+ for

3 seconds. The display will countdown to 3,2,1 and turn on the ice maker.

The 2nd Ice Off icon will blink three times and then stay off.

NOTES:

■■ Your ice maker has an automatic shutoff. The sensor will automatically stop ice production if the storage bin is full or the door is open. The control will remain in the On (I) position.

■■ Turn off the ice maker before removing the ice storage bin to serve ice or to clean the bin. This will keep the ice cubes from dropping out of the ice maker and into the freezer compartment. After replacing the ice storage bin, turn on the ice maker.

Ice Production Rate

■■ Your ice maker should produce approximately 3.5 lbs (1.6 kg) of ice per day under normal operation.

■■ To increase ice production, select the “Max Ice” feature from the control panel. The ice maker should produce approximately 4.6 lbs (2.1 kg) of ice per day. See the “Using the Controls” section.

Shelves, Bins, and Drawers

Door-within-Door bins

Get access to your favorite drinks and foods without opening the entire refrigerator.

Full Gallon Storage pull-out bins

Open the door-within-door and there are two special bins for your gallon storage.

Slide-Away Split Shelf

Some shelves will tuck away to create room for taller objects.

1.To retract the front section of the shelf, push the adjustable portion of the shelf as far back as needed toward the rear of the refrigerator.

2.Extend the front glass and front trim of the shelf by pulling the retracted portion of the shelf outward until it is fully extended.

Important information to know about glass shelves and covers:

Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping. Tempered glass is designed to shatter into many small, pebble-size pieces. This is normal. Glass shelves and covers are heavy. Use both hands when removing them to avoid dropping.

Under Shelf Prep Zone

Under one shelf, there are brackets installed to the supports (one bracket on each support). The under-shelf prep zone rests in these brackets.

To remove and replace the pan:

1.Remove the pan by lifting it up off the brackets. Press the right-hand side of the rack inward until it is free of its bracket. Lower the right-hand side slightly and disengage the lefthand side from its bracket.

2.Replace the pan by inserting the left-hand side into its bracket. Press inward on the right-hand side until it will slide past the bracket edge and set it into its bracket.

NOTE: Under shelf storage pan utilizes typically empty space beneath the shelf to create a prep zone ideal for doughs, desserts, casseroles, or marinating meats. The slide-out pan is oven and dishwasher safe and easily transitions from fridge to oven.

Shelves and Shelf Frames

The shelves in your refrigerator are adjustable to meet your individual storage needs.

Storing similar food items together in your refrigerator and adjusting the shelves to fit different heights of items will make finding the exact item you want easier. It will also reduce the amount of time the refrigerator door is open and save energy.

Shelf Height Adjustment

Shelf height can be adjusted by changing the adjustable shelf mounts between their vertical and horizontal positions.

1.Carefully lift the shelf off the shelf mounts and turn the flipper to the desired orientation.

2.Repeat for remaining shelf mounts.

3.Apply pressure to the top of the shelf to ensure the shelf is properly seated on the shelf mounts.

To remove and replace shelves:

1.Make sure adjustable shelf mounts are in the lower position before removing shelves. Also doors will need to be open at a 90˚ angle. If open wider, it will make it harder to remove the shelves.

2.Remove the middle shelf or top shelf by lifting it up and out of the shelf supports. Then pull the shelf forward and tilt down to a vertical position. Turn the shelf at an angle and pull out of the refrigerator.

NOTE: Remove middle shelf first before removing top shelf.

Infinity slide glass shelves should be pushed back in. When tilted up, make sure glass does not slide to front.

3.Remove the bottom shelf by lifting it up and out of the shelf supports. Then pull the shelf forward and tilt up to a vertical position. Turn the shelf at an angle and pull out of the refrigerator.

4.Replace the middle and top shelves by putting the shelf in the refrigerator at an angle with the shelf front down. Lift the front of the shelf up and slide in until rear shelf drops into the shelf supports. Lower the front of the shelf and make sure that the shelf is in position.

5.Replace the bottom shelf by putting the shelf in the refrigerator at an angle with the shelf up. Lift the front of the shelf down and slide in until rear shelf drops into the shelf supports. Lower the front of the shelf and make sure that the shelf is in position.

Shelves with under-shelf lighting (on some models)

By moving LED lighting to a new spot under the shelves, this leading-edge technology improves interior refrigerator lighting and aids in locating storage items.

Pull-Out Tray

To remove and replace the pull-out tray:

1.Pull the tray to the fully open position or when it stops.

2.Lift up and out of gliders toward the front of the refrigerator.

3.Replace the tray by placing it on the bottom tray guide and pushing it past the tray stop into position.

FreshSeal™ Crisper Drawers

To remove and replace the drawers:

1.Grasp the handle at the bottom of the drawer and slide the drawer straight out to the stop. Lift the drawer off the bottom guide.

2.Replace the drawer by placing it on the bottom drawer guide and pushing it past the drawer stop into position.

To remove the crispers cover (can remove only if platter pocket is removed first):

1.Remove the platter pocket first.

2.Holding the glass insert firmly with one hand, press up in center of glass insert until it rises above the plastic frame. Gently slide the glass insert forward to remove.

To replace crisper(s) cover(s):

1.Remove the crisper pan, platter pocket, and crisper glass before removing the crisper.

2.Fit back of cover frame into supports on side walls of the refrigerator and lower the front of the cover frame into place.

3.Slide rear of glass insert into cover frame and lower front into place.

Pullout Bin Installation

NOTE: Install bins on the right side of the refrigerator with the inner door closed and the outer door open.

Plastic trim frame

Pullout bin

1. Slide out all four bin glides.

2. Angle the plastic trim frame and place it onto the bin glide.

Plastic trim frame

Bin glide

Pull the front edge of the plastic trim frame as far forward as possible to engage the glide tab.

Trim groove

Glide

tab

3.Press down evenly on the front of the trim frame until it clicks into place.

4.Make sure both sides of the trim frame are securely attached to the bin glides.

5.Place the pullout bin over the plastic trim frame and gently push into place.

Refrigerator Door Bins

The bins on your refrigerator door are adjustable to meet your individual storage needs.

FreshSeal™ Herb Bin

This is a cylinder with a FreshSeal™ to keep sensitive items like herbs fresh longer. The container allows water to be added to keep stems wet without covering leaves. It can be placed anywhere in the refrigerator and accommodates tall items like parsley, cilantro, and rosemary in addition to herbs like oregano, thyme, and mint.

Freezer Drawers

3-Tier Self-Close Freezer Drawer with Extend-Freeze™ Setting or 3-Tier Self-Close Freezer Drawer with Ice Maker (depending on models)

Small Items Bin (on some models)

This drawer divider is not removable and is for small, delicate items. For storage flexibility, the drawer bin can move forward and back, allowing you to store larger items in one section of the freezer.

Pizza Pocket

Space at the front of the drawer allows vertical storage of additional pizza boxes.

Third Tier

This shelf is not removable. To allow access, the third tier is able to move backward, allowing access to items in the area below.

Ice Bin & Ice Scoop (on some models)

Ice storage for second ice maker

A.Pizza pocket

B.Third tier

C.Ice bin

	Audio Reference
Tone Assignment

Tone Name		Usage Examples

Power On		Cooling system is turned on every time
		the product is powered on.

Power Off		Cooling system is turned off.

Key Press		User presses a valid button.

Invalid (Error)		User presses two or more valid buttons at
		the same time. Count-down interruption
		for press-and-hold buttons. User presses
		pad when dispensing is not allowed.
Engage		Acknowledgment of entry into any mode
		or completion of dispensing.

Disengage		Acknowledgment of exit from any mode

Alert		Power Outage alert, Door Ajar alert

This table is for quick reference only. See corresponding sections for details. In case of inconsistency, section details will prevail.

+ 96 hidden pages