KEYENCE BL-1300 User Manual

The "BL-1300 Series Laser Barcode Reader" uses a visible laser light

DANG ER

WARNING

CAUTION

Note

TIPS

WARNING

AVERTISSEMENT

96M12900

*96M12900-1*

BL- 1300/1301/1300HA/

1301HA/1370/1371

BL-1350HA/1351HA

source.

Laser Bar Code Reader

BL-1300 Series

Instruction Manual

Failure to follow these instructions may lead to death or
serious injury.

Failure to follow these instructions may lead to injury.

Failure to follow these instructions may lead to product
damage (product malfunction, etc.).

Provides additional information on proper operation.

Indicates useful information or information that aids
understanding of text descriptions.

Safety information for BL-1300 Series

 General precautions

• Do not use this product for the purpose to protect a human body or

part of a human body.

• This product is not intended for use as an explosion-proof product. Do

not use this product in a hazardous location and/or potentially
explosive atmosphere.

• We recommend that you take substantial safety measures to avoid any

damage in the event a problem occurs.

• If the BL-1300 is modified or used in any way other than described in

the specifications, its function and performance cannot be guaranteed.

• When the BL-1300 is used in combination with other instruments, the

function and performance may be effected by operating conditions and
the surrounding environment.

• It is prohibited to use or copy all or any part of this manual without prior

approval.

• The information contained in this manual is subject to change without

notice.

Model

Wavelength 660 nm

Output 85 W

Pulse duration 112 s

FDA (CDRH)

Laser Class

The BL-1300 Series barcode readers are equipped with the following
safety measures.

• Laser radiation emission warning LED (LASER LED)

During laser emission, the LASER ON LED illuminates. The LED ON
status can be clearly visible through protective eyewear; specifically
designed for the wavelength of 660nm.

• Laser forced OFF command

Sending the laser forced OFF command to the BL-1300 can inhibit
emission of laser beams. When working near the laser transmitter, be
sure to use the laser forced OFF command to avoid looking into the
laser beams.

* When this command is selected, the bottom STABILITY LED flashes.

Part 1040.10

IEC 60825-1 Class 2 Laser Product

• Follow the instructions mentioned in this manual.

Otherwise, injury to the human body (eyes and skin)
may result.

Precautions on class 2 laser products

• Do not stare into the beam.

• Do not direct the beam at other people or into areas

WARNING

• Be careful of the path of the laser beam.

•

• Do not disassemble this product. Laser emission

BL-1300, 1301, 1300HA, 1301HA, 1350HA, 1351HA, 1370, 1371

Class 2 Laser Product

where other people unconnected with the laser work
might be present.

If there is a dang er that the operator may be
exposed to the laser beam reflected by specular or
diffuse reflection, block the beam by installing an
enclosure with the appropriate reflectance.
Install the products so that the path of the laser beam
is not as the same height as that of human eye.

from this product is not automatically stopped when
it is disassembled.

 IEC warning/explanatory label locations

 Safety precautions on laser product

Use of controls or adjustments or performance of
procedures other than those specified herein may result
in hazardous radiation exposure.

L'utilisation des commandes ou réglages ou l'exécution
des procédures autres que celles spécifiées dans les
présentes exigences peuvent être la cause d'une
exposition à un rayonnement dangereux.

Use the suitable IEC warning/explanatory label included in the package
of this product according to the countries and/or regions where this
product is used.
In this case, it can be affixed on the IEC warning/explanatory label,
which has already been affixed to this product.

1

E BL-1300-IM

 For proper use of this product

CAUTION

Main unit

Instruction manual

Mounting bracket

BL-1300/1301/1300HA/

1301HA/1370/1371

BL-1350HA/1351HA

BL-1300/1301/1300HA/

1301HA/1370/1371

BL-1350HA/1351HA

Mounting bracket: 1

Mounting bracket A and B: 1 each

Insulating spacer: 4

Washer: 4

Mounting screw (M3): 2

Laser warning seal set: 1

BL- 1300/1301/1300HA/

1301HA/1370/1371

BL-1350HA/1351HA

1

Laser Bar Code Reader

BL-1300 Series

Instruction Manual

General precautions

•

Do not use this product for the purpose to protect a human body or
part of a human body.

•

This product is not intended for use as an explosion-proof product. Do
not use this product in a hazardous location and/or potentially
explosive atmosphere.

•

We recommend that you take substantial safety measures to avoid
any damage in the event a problem occurs.

•

If the BL-1300 is modified or used in any way other than described in
the specifications, its function and performance cannot be guaranteed.

•

When the BL-1300 is used in combination with other instruments, the
function and performance may be effected by operating conditions and
the surrounding environment.

•

It is prohibited to use or copy all or any part of this manual without prior
approval.

•

The information contained in this manual is subject to change without
notice.

Safety precautions on laser product

The "BL-1300 Series Laser Barcode Reader" uses a visible laser light
source.

The BL-1300 Series barcode readers are equipped with the following
safety measures.

•

Laser radiation emission warning LED (LASER LED)

During laser emission, the LASER ON LED illuminates. The LED ON
status can be clearly visible through protective eyewear; specifically
designed for the wavelength of 660nm.

•

Laser forced OFF command

Sending the laser forced OFF command to the BL-1300 can inhibit
emission of laser beams. When working near the laser transmitter, be
sure to use the laser forced OFF command to avoid looking into the
laser beams.

*When this command is selected, the bottom STABILITY LED flashes.

IEC warning/explanatory label locations

Use the suitable IEC warning/explanatory label included in the package
of this product according to the countries and/or regions where this
product is used.
In this case, it can be affixed on the IEC warning/explanatory label,
which has already been affixed to this product.

DANGER

Failure to follow these instructions may lead to death or
serious injury.

WARNING

Failure to follow these instructions may lead to injury.

CAUTION

Failure to follow these instructions may lead to product
damage (product malfunction, etc.).

Note

Provides additional information on proper operation.

TIPS

Indicates useful information or information that aids
understanding of text descriptions.

Safety information for BL-1300 Series

WARNING

Use of controls or adjustments or performance of
procedures other than those specified herein may result
in hazardous radiation exposure.

96M12614

Model

BL-1300, 1301, 1300HA, 1301HA, 1350HA, 1351HA, 1370, 1371

Wavelength 660 nm

Output 85 μW

Pulse duration 112 μs

Laser Class

FDA (CDRH)
Part 1040.10

Class 2 Laser Product

IEC 60825-1 Class 2 Laser Product

WARNING

•Follow the instructions mentioned in this manual.
Otherwise, injury to the human body (eyes and skin)
may result.

Precautions on class 2 laser products

•Do not stare into the beam.

•Do not direct the beam at other people or into areas

where other people unconnected with the laser work
might be present.

•Be careful of the path of the laser beam.

If there is a danger that the operator may be
exposed to the laser beam reflected by specular or
diffuse reflection, block the beam by installing an
enclosure with the appropriate reflectance.

•

Install the products so that the path of the laser beam
is not as the same height as that of human eye.

•Do not disassemble this product. Laser emission

from this product is not automatically stopped when
it is disassembled.

BL-1300/1301/1300HA/

1301HA/1370/1371

BL-1350HA/1351HA

Precautions on use

•

The BL-1300 uses a 5 V DC power supply. Using a
different voltage level may damage the unit. When using
the KEYENCE power supply unit N-R2, N-R4, N-UB, N-L1,
NX-50 Series or DV-90 Series, select the voltage level
which can be supplied by the power supply unit. If a
nonconforming power supply is connected, the BL-1300
may be damaged.

• Before connecting or disconnecting the cable, be sure
to turn off any device connected to the BL-1300 Series.
Otherwise, the BL-1300 Series may be damaged.

• Do not disassemble or modify the BL-1300 Series, as
this may cause product failure.

• Locate cables as far as possible from high-voltage
lines and power lines. Otherwise, generated noise may
cause product failure or malfunctions.

•

Before mounting the BL-1300 Series, insulate the
mounting location. Otherwise, generated noise may cause
product failure or malfunctions.

• The BL-1300 is a
precision instrument.
Dropping the unit or
subjecting it to shock
may cause damage. Be
careful when
unpacking, carrying, an
mounting it. Do not
hold the units by their
cables.

• Do not hold the units by
their cables when carrying
them. The units may hit
each other and become
damaged.

 Canada IC (Industry Canada) regulations

The BL-1300 Series conforms to the following IC EMI regulations.

• ICES-003, Class B digital apparatus

 CE marking

The BL-1300 Series complies with the following essential requirements
of the EU Directives.

• EMC Directives (2004/108/EC)

• Low-voltage Directives (2006/95/EC)

The following harmonized standards are applied to these products in
order to confirm the compliance.

• Applicable standards (EMI) EN55011, Class A

EN55022, Class B

• Applicable standards (EMS) EN61000-6-2

EN61000-6-1

* The length of the communication and power cables should be less than 30

m.

Package Contents List

If abnormal conditions are encountered

If the following conditions are encountered, turn off the
power supply unit immediately. Continuing to use the BL­1300 Series under abnormal conditions may cause fire,
electric shock, or product failure. Contact your nearest
KEYENCE sales office (listed at the end of this manual)
for rep airs.

• Water or foreign matter enters the BL-1300 Series.

• The BL-1300 Series is dropped or the housing is

damaged.

• The BL-1300 Series produces smoke or an abnormal

Precautions on Regulations and Standards

smell

 UL Certificate

The BL-1300 Series is an UL/c-UL certified product.

• UL File No. E207185, E167973

• UL category NRAQ/NRAQ7, NWGQ2/NWGQ8

Be sure to observe the following installation and environment conditions.

• Be sure to use a power supply that provides class 2 output as defined

in NFPA70 (NEC: National Electrical Code).

• Pollution degree 2

• Overvoltage category I

 FDA regulations

The BL-1300 Series is classified as class 2 laser product. The
classification is based on IEC60825-1 following the Laser Notice No. 50
from FDA (CDRH).

 FCC regulations

The BL-1300 Series complies with the following FCC EMI regulations.

• FCC Part 15 Subpart B, Class B digital devices

E BL-1300-IM

2

Part Names and Functions

6. Transmitter/receiver

7. Connector

8. Cable

8. Cable

1. LASER LED

2. OK/NG/ERR LED

3. TIMING LED

4. STABILITY LED

5. TEST SWITCH

6. Transmitter/receiver

7. Connector

610594

21

8

1211

3

7

Cable head cross-section view
RP17-13PA-12PC plug (male)

Manufactured by Hirose Electric Co., Ltd.

Note

GND

+5V

12

11

5 VDC

+

10 kΩ

100 Ω

TIM

GND

12

6,10

4.7 kΩ

5 VDC

Internal circuit

Contact

or

non-contact

GND

OK/NG

12

+

1, 2,
5, 9

3.3 kΩ

6.8 kΩ

33 V

Load

* Rated load: 24V DC (30 mA) or less

Internal circuit

BL-1300 Series PC

Round
connector
12-pin (male)

D-sub9 pin
(female)
#4-40 screw

Number Name Function

1 LASER LED Lit when laser beams are emitted.

• When OK output is ON: The green LED
lights.

2 OK/NG/ERR LED

3 TIMING LED Lit when trigger input is ON.

4 STABILTY LED

5 TEST SWITCH

6 Transmitter/receiver

7 Connector Used to connect to the communication unit.

8 Cable Cable length is 2 m.

• When NG output is ON: The orange LED
lights.

• When ERR output is ON: The red LED
lights.

Displays the reading stability and the BL­1300 operating status.

This switch is used to perform the following
operations.

• If this switch is pressed once shortly, a
barcode is read once.

• Starting and canceling the test mode

• Start reading of batch set bar codes

• Registering preset data

• Canceling PLC link errors

• Fixing the communication setting to the
initial value when setting transmission and
reception

Receives the emitted and reflected light of
laser beams and reads barcodes.

Connection and Wiring Method

 Connecting the power supply

Connect a cable with a
length of 4.8 m or less.

• Reverse connection of the power supply is strictly

prohibited. This may cause product failure.

• Use a stable power supply of 5V DC
power supply outside this range may cause product
failure.

 5%. Using a

 Wiring IN1/IN2 input pins

• The IN1 (timing) input is used to trigger the BL-1300 Series to read

barcodes (to emit a laser beam).

• The IN2 (preset) input is used to trigger the BL-1300 Series to register

barcode data.

IN1/IN2 input is performed by no-voltage input.

 Wiring OUT1/OUT2/OUT3/OUT4 output pins

• OUT1 (OK) is used as output indicating that reading is successfully

completed and that the comparison and matching with preset data is
judged as OK.

• OUT2 (NG/ERROR) is used as output indicating that reading has

failed and that the comparison and matching with preset data is judged
as NG.

• OUT3 (ERROR) is used as output indicating that reading has failed.

• OUT4(BUSY) is output any time the trigger input cannot be accepted,

such as cases where the BL-1300 Series is at initial start-up or in
setting mode, the motor/laser is damaged, the motor/laser is locked, or
the number of rotations of the motor is changed.

The output form of each signal is NPN open collector.

 Connection connector pin layout

Pin number Symbol Explanation

1 OUT1 Output pin 1 (initial value OK output)

2OUT2

3 TXD RS-232C transmission

4 CTS RS-232C transmission permitted

5 OUT4 Output pin 4 (initial value BUSY output)

6 IN2 Input pin 2 (initial value PRESET input)

7 RXD RS-232C reception

8 RTS RS-232C reception permitted

9 OUT3 Output pin 3 (initial value ERROR output)

10 IN1 Input pin 1 (initial value TIMING input)

11 +5V +5V power supply

12 GND (SG) Common GND

* The shield line is directly connected to the common GND.

Output pin 2 (initial value NG/ERROR
output)

 Wiring RS-232C

When connecting the BL-1300 Series to the PC, connect as shown
below.

RxD (RD)

TxD

3

CTS

4

RxD

7

8

RTS

GND

12

11

+5V

+

3

2

7

3

8

5

4

6

RTS (RS)

TxD (SD)

CTS (CS)

GND (SG)

DTR (ER)

DSR (DR)

E BL-1300-IM

Installing the BL-1300 Series

Note

Front type
BL-1300/1301/1300HA/

1301HA/1370/1371

Side type
BL-1350HA/1351HA

Reading distance

Reading distance

15

15

Within
10

Within
10

15

Front type Side type

Incorrect

Incorrect

Supplied
mounting
screw (M3)

Mounting
bracket B

Laser
beam

When mounting bracket A is
used

Laser
beam

Mounting
bracket A

Supplied mounting
screw (M3)

When mounting bracket B is
used

Note

Note

When mounting bracket A is used

Mounting screw
(M4)

Washer
Insulating

spacer

When mounting bracket B is
used

Mounting
screw (M4)

Washer

Insulating
spacer

Laser beam

Mounting
bracket

Supplied mounting
screw (M3)

Supplied mounting
screw (M3)

Mounting
bracket

Laser
beam

Mounting
bracket

Mounting
screw (M4)

Washer

Insulating
spacer

When installing the BL-1300 Series, adjust the mounting angle and
distance as shown below.

 Adjusting the mounting angle

Mount the BL-1300 Series so that a laser beam is applied at an angle of
approximately 15.
For the front type of the BL-1300 Series BL-1300/1301/1300HA/1301HA/
1370/1371, the unit must be tilted at an angle of 15.
For the side type BL-1350HA/1351HA, it is not necessary to tilt the unit
because a laser beam is emitted at an angle of 15.

 Adjusting the reading distance

The BL-1300 Series normally provides stable reading when it is mounted
at the following distance.

Model Mounting distance

BL-1300/1301 : 120 mm

BL-1300HA/1301HA : 90 mm

BL-1350HA/1351HA : 65 mm

BL-1370/1371 : 230 mm

* The supplied mounting bracket facilitates the angle setting.
* The reading rate check mode ensures an optimal reading position.

• Do not mount the BL-1300 Series so that the laser

beam is applied to bar codes at a right angle (10).
Otherwise, the specular reflections may cause
unstable reading or reading errors.

2 Fasten the mounting bracket to the unit.

* Mounting screws (M4) are not included.

Be sure to mount the supplied insulation spacer to
suppress the influences of noises from the unit side.
If the insulation spacer is not mounted, there is risk of
the occurrence of a reading error or a wrong reading.

 Attaching the side type BL-1350HA/1351HA to the

mounting bracket

The following is the procedure for mounting the BL-1350HA/1351HA
using the supplied mounting bracket.

1 Attach the BL-1300 Series to the mounting bracket.

* The mounting bracket for the BL-1300 allows two mounting or ientations.

Choose the appropriate orientation according to the application.

* Refer to page 5 for the dimensions of the mounting bracket.

• The reading distance and angle may vary depending

on the narrow bar width, size, and printing quality of
bar codes. Be sure to test the BL-1300 Series' ability to
read the actual bar codes using "Reading rate check
mode".

Mounting the BL-1300 Series

 Attaching the

front type BL-1300/1301/1300HA/1301HA/

1370/1371 to the mounting bracket.

The following procedure is for mounting the BL-1300 using the supplied
mounting bracket.

1 Attach the BL-1300 Series to the mounting bracket.

* Refer to page 5 for the dimensions of the mounting bracket.

E BL-1300-IM

2 Fasten the mounting

bracket to the unit.

* Mounting screws (M4) are

not included.

Be sure to mount the supplied spacer to suppress the
influences of noise. A reading error or an incorrect error
reading may occur if the insulation spacer is not
mounted.

4

 Mounting the BL-1300 Series without the mounting

Note

BL-1300/1301/1300HA/

1301HA/1370/1371

BL-1350HA/1351HA

Mounting screw (M3)

Mounting screw (M3)

Mounting
hole

Mounting
hole

4.2

29.75

22.53.5

33

3.5

11.5

14.55

21

31

29.33

403.8

15.95

23.46

Laser beam

2-M 3 Depth 4

Center of
scanning

15 min.

Cable length: 1.8 m

4.2

18.66

48

11.5

3.5

38.1

6.45

2122 3.5

17.6

483.8

41.56

23.47

15°

Laser
beam

2-M 3
Depth4

Cable length: 2 m

15 min.

Center of
scanning

25

7.82

43.35

2.2

59.6

19.6

3

5.5

5.5

9

14

37.6

38.65

2-R 2.75

R19

2-R 2.75

5°

10°

15°

2.2

40

626.5

35.3

3

6.5

5.3

32.7

11.4

49.35

43.58

28.01

2-R 2.65

2-R 2.65

15

°

Mounting bracket A

Mounting bracket B

Laser
beam

Laser beam

18.66

2.2

1.6

21

19.6

67.6

48

21

3

11

38.5

5.3

5.3

5.5 36

3

41.56

2-R 2.65

2-R

2.65

15°

bracket

1 Fasten the BL-1300 Series.

Fasten the BL-1300 Series in the mounting position with M3 screws.

* The M3 screws are not included. Select the M3 screws after checking

the panel thickness and other factors of the mounting position.
(The mounting hole for the BL-1300 Series is 4 mm deep.)

To suppress the influence of noise, mount the insulation
plate between the unit and the place it will be mounted. If
the insulation plate is not mounted, a reading error or an
incorrect reading may occur.

Dimensions

 Main unit (BL-1300/1301/1300HA/1301HA/1370/1371)

 Mounting bracket

* On the bottom of the mounting bracket, an insulation sheet is attached.

Do not remove it.

•

For the front type

 Main unit (BL-1350HA/1351HA)

• For the side type

5

E BL-1300-IM

Specifications

Copyright (c) 2014 KEYENCE CORPORATION. All rights reserved.

12900E 1014-1 96M12900 Printed in Japan

*96M12900-1*

 General specifications

Type Standard type High-resolution
Scanning direction Front

Light source

Scan method Single Raster Single Raster
Focal distance 120 mm 90 mm

Reading distance

Reading bar width 0.125 mm or more 0.08 mm or more

Maximum reading label width

PCS 0.4 or more
Scan count 500 to 1300 scans/second

Supported codes

Reading digit

Rating

Weight Approx. 115 g

Ty pe

Scanning direction Side Front

Light source

Scan method Single Raster Single Raster
Focal distance 65 mm 230 mm

Reading distance

Reading bar width 0.08 mm or more 015 mm or more

Maximum reading label
width

PCS 0.4 or more
Scan count 500 to 1300 scans/second

Supported codes

Reading digit

Rating

Weight Approx. 130 g Approx. 115 g

Model BL-1300 BL-1301 BL-1300HA BL-1301HA

Visible red semiconductor laser

Output 85 W
Pulse duration 112 s

Laser Class

(When narrow width is

(Distance 350 mm,

Narrow bar width 1.0

CODE39, ITF, Industrial2of5, Standard2of5,

Enclosure rating IP65
Ambient light Sunlight: 10000 lx, Incandescent lamp: 6000 lx
Ambient

temperature
Storage ambient

temperature
Relative humidity 35 to 85%, No condensation
Operating

atmosphere

Environment resistance

Vibration

Power supply
voltage

Power consumption 400 mA max.

Model

Output 85 W
Pulse duration 112 s

Laser Class

Enclosure rating IP65
Ambient light Sunlight: 10000 lx, Incandescent lamp: 6000 lx
Ambient

temperature
Storage ambient

temperature
Relative humidity 35 to 85%, No condensation
Operating

atmosphere

Environment resistance

Vibration

Power supply
voltage

Power
consumption

(148 digits for the CODE128 start character C)

BL-1350HA BL-1351HA

side-scanning type

(When narrow width is

201 mm
175 mm, Narrow bar

CODE39, ITF, Industrial2of5, Standard2of5,

(148 digits for the CODE128 start character C)

(Wavelength: 660 nm)

Class 2 Laser Product

(IEC60825-1,FDA(CDRH) Part 1040.10)

65 to 500 mm

1.0 mm)

339 mm

COOP2of5, CODABAR, CODE128,

2 hours each in X, Y and Z directions

High-resolution,

(IEC60825-1,FDA(CDRH) Part 1040.10)

40 to 250 mm

0.5 mm)

width 0.5 mm)

COOP2of5, CODABAR, CODE128,

2 hours each in X, Y and Z directions

*1

*1

mm)

GS1-128, CODE93,

UPC/EAN, GS1 DataBar

-20 to 60C

No dust or corrosive gas present

10 to 55 Hz, amplitude 1.5 mm,

5V DC 5%

Visible red semiconductor laser

(Wavelength: 660 nm)

Class 2 Laser Product

*1

*1

(Distance

GS1-128, CODE93,

UPC/EAN, GS1 DataBar

-20 to 60C

No dust or corrosive gas present

10 to 55 Hz, amplitude 1.5 mm,

5V DC 5%

400 mA max.

45 to 270 mm

(When narrow width is

189 mm

(Distance 189 mm,

Narrow bar width 0.5

74 digits

0 to 45C

BL-1370 BL-1371

Long distance type

160 to 600 mm

(When narrow width is

404 mm *1 (Distance
420 mm, Narrow bar

width 1.0 mm)

74 digits

0 to 45C

0.5 mm)

1.0 mm)

*1

mm)

*1

Specifications at 500 scans/second

· The laser classification for FDA(CDRH) is implemented based on IEC60825-1 in

accordance with the requirements of Laser Notice No. 50.

· To comply with UL/IEC60950-1, use the limited power source defined in

UL/IEC60950-1.

· The internal settings of the unit are written to the internal memor y.

(Re-writable 100,000 times)

 Interface specifications

Input pin

Output type 4 (OUT1 to 4) NPN open collector

*1

Output
pin

Serial
interface

Rating load 24 V DC, 30 mA

Leakage current at
OFF

Residual voltage at
ON

Transmission method EIA RS-232C compliant

Communication rate

Synchronization Start-stop synchronization

Data length 7/8 bits

Stop bit length 1/2 bits

Parity check None/even/odd

2 (IN1, 2), no-voltage input

(contact, non-contact)

0.1 mA or less

0.5 V or less

600, 1200, 2400, 4800, 9600, 19200,

31250, 38400, 57600, 115200 bps

WARRANTIES AND DISCLAIMERS

KEYENCE, at its sole option, will refund, repair or replace at no charge any
defective Products within 1 year from the date of shipment. Unless stated
otherwise herein, the Products should not be used internally in humans, for
human transportation, as safety devices or fail-safe systems. EXCEPT FOR

THE FOREGOING, ALL EXPRESS, IMPLIED AND STATUTORY
WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY,
FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OF
PROPRIETARY RIGHTS, ARE EXPRESSLY DISCLAIMED. KEYENCE
SHALL NOT BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
CONSEQUENTIAL OR OTHER DAMAGES, EVEN IF DAMAGES RESULT
FROM THE USE OF THE PRODUCTS IN ACCORDANCE WITH ANY
SUGGESTIONS OR INFORMATION PROVIDED BY KEYENCE. In some

jurisdictions, some of the foregoing warranty disclaimers or damage limitations
may not apply.

E 1101-3

*1

E BL-1300-IM

6