Place a mug on the Drip Tray. Select the brew size you want
using the Selector Switch.
Press the BREW Button. This will
yield a serving of the selected
size; small mug of 170 ml (6 oz),
medium mug of 220 ml (8 oz) or
large mug of 300 ml (10 oz)
(approximate sizes only).
Enjoy!
Remove the Water Reservoir
from the brewer by first
removing the Water Reservoir
Lid, then lifting the Water
Reservoir straight up and
away from the brewer.
Rinse the Water Reservoir and
fill with bottled or filtered water.
A. Set-Up B. Brew
11 13 1412 1
Remove adhesive tape.
Extend the Power Cord
and plug the brewer into
the mains socket. Make sure
the BREW/DRAIN Selector
Knob at the back of the
brewer is set to BREW.
2
Press the POWER Button.
The green light will come on.
The blue ADD WATER Light will
also come on.
3 4
Select a K-CupTM pack. Do not remove or
pierce the foil lid.
Lift the silver Handle, place the K-Cup
TM
pack in the K-Cup
TM
Pack Holder then lower
the Handle all the way down to puncture the
K-Cup
TM
pack.
Please be careful to avoid the sharp needles
in the K-Cup
TM
Pack Assembly Housing.
www.keurig.co.uk
P/N 60-202827-000 Rev A
11/13
SET-UP GUIDE
Keurig® K-CupTM K140 Brewer
Please consult the Owner’s Manual for more information on your brewer.
If you need further assistance please contact your Keurig Master
Distributor.
BREW
PUSH TO BREW
DESCALE
PUSH TO BREW
AUTO OFF
ADD WATER
BREW
POWER
DRAIN BREWER
HEATING
TM
Your Keurig® brewer will automatically fill
(priming it) and the water will be heated.
This takes less than 5 minutes. While
heating, the red HEATING Light will come
on. When ready, the red light will turn off.
Once finished, pour the hot water
into the sink.
The green Brew Size Indicator Lights
above the BREW Button will flash. If they
are not flashing, make sure the Handle is
pressed all the way down. Press the BREW
Button to start priming. The lights will
continue to flash until priming is complete.
While your brewer refills and reheats between
brews, the red HEATING Light will come on.
During this time the pump may cause a
vibration noise. This is normal. The red light
will turn off when the water has heated and the
brewer is ready.
The one-time priming process is now complete
and you are ready to enjoy your first cup!
Replace the Water Reservoir, then replace
the Water Reservoir Lid.
Place a large mug - that can hold 300 ml
(10 oz) or ½ pint - on the Drip Tray.
5 6 87
Lift and lower the Handle. DO NOT insert
a K-Cup
TM
pack. The blue BREW Light will
flash. Press the BREW Button to start a
cleansing brew. Hot water will flow into
your mug.
9 10
www.keurig.co.uk
DO NOT lift the Handle while heating
or brewing.
Remove used K-Cup
TM
pack after brewing.
CAUTION: K-Cup
TM
pack will be hot.
NOTE: If your brewer has been exposed to
temperatures below freezing, we recommend you
allow two hours for an unpacked brewer to warm
to room temperature before powering on.
DO NOT remove or puncture the foil lid of the
K-Cup
TM
pack.
DESCALE
PUSH TO BREW
AUTO OFF
ADD WATER
BREW
POWER
DRAIN BREWER
HEATING
DESCALE
PUSH TO BREW
AUTO OFF
ADD WATER
BREW
POWER
DRAIN BREWER
HEATING
DESCALE
PUSH TO BREW
AUTO OFF
ADD WATER
BREW
POWER
DRAIN BREWER
HEATING
Loading...