Owner’s manual
Keurig® K-Cup™ K10 MINI Plus Brewer
IMPORTANT SAFEGUARDS Safe Operation & Use
When using electrical appliances, basic
safety precautions should be followed,
including the following:
1. Read all instructions before using.
2. Do not touch hot surfaces. Use handles
and knobs when available.
3. This appliance must be properly
installed and located in accordance
with these instructions before it is used.
4. The use of accessory attachments
not recommended by the appliance
manufacturer may result in fire,
electrical shock or injury to persons.
5. Do not place on or near a hot gas or
electric burner, or in a heated oven.
6. Do not use outdoors.
7. To protect against fire, electric shock
and injury do not immerse cords, plugs,
or the appliance in water or any other
liquid.
8. Do not overfill the Cold Water Reservoir
with water.
9. Use only water in this appliance! Do
not put any other liquids or foods in the
Water Reservoir except as instructed in
the Cleaning Instructions in this guide.
10. Turn off and unplug the brewer before
cleaning or maintenance. Allow to cool
before putting on or taking off parts
and before cleaning the appliance.
11. For best operation, plug the appliance
into its own electrical outlet on a
dedicated circuit to prevent flickering
of lights, blowing of fuses or tripping a
circuit breaker.
12. Do not operate any appliance with a
damaged cord or plug or after
the appliance malfunctions or is
damaged in any manner. Contact
Keurig Customer Service to report
any malfunction of or damage to the
brewer.
13. Do not let the cord hang over the edge
of the table or counter, or touch hot
surfaces.
14. To disconnect, press the Power Button
on the brewer to “OFF” status and then
remove the plug from the wall outlet.
15. Close super vision is necessary when
any appliance is used by or near
children.
16. Do not lift the brewer Handle while
brewing is in progress; scalding
may oc cur.
17. Always keep the Cold Water Reservoir
Lid closed unless you are refilling it.
18. This appliance is equipped with a power
cord having a grounding wire with a
grounding plug. The appliance must
be grounded using a 3-hole properly
grounded outlet. In the event of an
2 3
electrical short circuit, grounding
reduces the risk of electrical shock.
19. If the outlet is a standard 2-prong wall
outlet, it is your personal responsibility
and obligation to have it replaced with a
properly grounded 3-prong wall outlet.
20. Do not, under any circumstances, cut or
remove the third (ground) prong from
the power cord or use an adapter.
21. Consult a qualified electrician if
the grounding instructions are not
completely understood, or if doubt
exists as to whether the appliance is
properly grounded.
22. Do not use the appliance for other than
its intended use.
SAVE THESE
INSTRUCTIONS.
CAUTION: There are two sharp needles that puncture the
®
K-Cup
pack, one above the K-Cup® Pack Holder and the
other in the bottom of the K-Cup® Pack Holder. To avoid risk
of injur y, do not put your fingers in the K-Cup® Pack
Assembly Housing.
CAUTION: There is extremely hot water in the K-Cup
the brew process. To avoid risk of injur y, do not lift the Handle or open the
K-Cup® Pack Assembly Housing during the brewing process.
CAUTION: Please always keep the brewer in its upright position to avoid
potential injury and/or damage to your brewer.
SHORT CORD INSTRUCTIONS: A short power supply cord is provided to
reduce the risk of becoming entangled in or tripping over a longer cord.
If an extension cord is used, (1) the marked electrical rating of the cord set or
extension cord should be at least as great as the electrical rating of the
appliance; (2) the cord should be arranged so that it will not drape over the
countertop or tabletop where it can be pulled on by children or tripped over
unintentionally; and (3) the extension cord must include a 3-prong grounding plug.
THIS PRODUCT IS FOR HOUSEHOLD USE ONLY.
®
Pack Holder during
WARNING KEEP ALL PL ASTIC BAgS AwAY FROM CHILDREN.
WARNING THIS PRODUCT CONTAINS CHEMICALS, INCLUDINg
LEAD, wHICH IS KNOwN TO THE STATE OF CALIFORNIA TO CAUSE CANCER,
BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM.
WARNING TO USERS AND PARENTS
1. DO NOT permit children to use brewer unless there is adult
supervision. Brewer dispenses very hot water.
2. SPECIAL NOTICE FOR HOT COCOA USERS:
IMMEDIATELY AFTER USING A HOT COCOA K-CUP® PACK, RUN a Hot
®
Water Brew Cycle without a K-Cup
pack to avoid the possibility of
clogging the exit needle. DO NOT assume the next user will do this.
WARNING: TO REDUCE THE RISK OF FIRE OR
WARNING
RISK OF FIRE OR
ELECTRIC SHOCK
DO NOT OPEN
ELECTRIC SHOCK, DO NOT REMOVE THE
BOTTOM COVER. NO USER SERVICEABLE
PARTS ARE INSIDE. REPAIR SHOULD BE DONE
!
BY AUTHORIZED SERVICE PERSONNEL ONLY.
TABLE OF CONTENTS
KEURIG® GOURMET SINGLE CUP HOME BREWING SYSTEM
K10 MINI Plus Brewer — Using Your Brewer
SECTION 1—Brewer Overview .......................................................... 4
SECTION 2— Helpful Hints
SECTION 3—Buttons & Indicators .........................................................7
SECTION 4— Set-Up & Operation
Initial Cleansing & First Brew ........................................................... 8
SECTION 5—Cleaning & Maintenance
Cleaning External Par ts ..................................................................12
Cleaning the K-Cup® Pack Holder Assembly .............................. 12
Cleaning the Cold Water Reservoir ................................................ 14
Emptying the Internal Hot Water Tank ........................................... 14
De-Scaling Your Brewer ..................................................................14
Storage ...............................................................................................15
Storing the Power Cord .................................................................... 15
SECTION 6—Troubleshooting .......................................................... 16
SECTION 7—Warranty
Record your Brewer Serial Number here.
.................................................................6
...................................................................... 18
SECTION 1 Brewer Overview
A
Water Level Guide
Handle
B
®
Pack Holder Assembly
K-Cup
C
®
Pack Holder
K-Cup
D
Funnel
E
F
G
H
I
J
K
L
M
N
O
®
Pack Assembly Housing
K-Cup
Drip Tray Overfill Indicator
Drip Tray Plate
Dr ip Tr ay
Cold Water Reservoir Lid
Cold Water Reservoir
BREW Button
LED Indicator
Power Button
Power Cord
J
A
K
B
L
M
D
C
E
G
H
I
F
P
N
O
Remov ing the ser ial number l abel from th e brewer wi ll void war ranty.
P
Drip Tray Base
4 5
For replacement parts, please visit ww w.keurig.com
SECTION 2 Helpful Hints
SECTION 3 Buttons & Indicators
1. Plug Power Cord into an Independent,
Grounded Outlet – If the electric circuit is
overloaded with other appliances, your brewer
may not function properly.
2. Initial Cleansing Brew – Before you make your
first beverage, perform an initial cleansing
brew without inserting a K-Cup
3. One Cup at a Time – Your new brewer makes
one fresh beverage at a time. You will need to
add fresh water each time you brew. Unlike
other Keurig
not store water in the reservoir.
4. The Right Water Makes a Difference – For the
best-tasting gourmet coffee, tea or hot cocoa,
Keurig recommends using bottled or filtered
water. We do not recommend using distilled or
reverse osmosis water. Note that water quality
can vary from place to place. If you notice an
undesirable taste in your beverage (such as
chlorine or other mineral substance), we
recommend trying bottled water or water from
a filtration system. For best results, carefully
follow manufacturer’s instructions when using
any water filtration system.
5. Customize Your Size, Flavor & Brew – With
over 200 K-Cup
fill levels, your brewer provides endless
customization options – so that you can create
the size, flavor and strength of each beverage
that is perfect for you. For a strong, intense
flavor, select an Extra Bold K-Cup
®
brewers, the K10 MINI Plus does
®
pack varieties and multiple
®
pack.
®
pack (with
up to 30% more ground coffee than regular
varieties) along with a brew size that’s right for
you. The less water you use, the more intense
the flavor in your cup. The more water you use,
the less intense the flavor in your cup.
Use the Water Level Guide located inside the Cold
Water Reservoir to customize your brew size.
6. Brewing Iced Beverages – Your iced tea and
iced coffee taste best when fresh-brewed hot
over ice. Try it by placing a tall cup filled with
ice on the Drip Tray, choose your favorite
®
pack and follow the brewing
K-Cup
instructions on page 8. Also, look for the
“Brew Over Ice” icon on K-Cup
crafted to brew over ice! IMPOR TANT: Do not
brew into a cup made of glass. Doing so may
cause the glass to crack or break.
7. Remove K-Cup
page 8 for brewing instructions.
8. Brewing into a Tall Mug – To brew into a tall
mug, simply remove the Drip Tray Assembly
and place the tall mug on the Drip Tray Base.
Without the Drip Tray A ssembly, however, you
do lose the benefit of the Drip Tray to contain
any excess water.
9. The Drip Tray – Any liquid over flow (from your
cup or from the Cold Water Reservoir) will be
caught in the Drip Tray. Be sure to empty the
Drip Tray when the red Drip Tray Over flow
Indicator pops up.
®
Pack After Use – Please see
6 7
®
packs specially
10. Automatic Shut-Off – As a safety feature, your
brewer will shut off automatically when it is
idle for longer than 90 seconds. Simply press
the Power Button to restart.
11. Clean Your Brewer Regularly – To keep
your brewer looking and performing at its
best, be sure to clean the external and
internal components on a regular basis.
See page 12 for more information.
12. De-Scaling – Depending on the mineral
content of the water in your area, calcium
deposits or scale may build up in your brewer.
Scale is non-toxic, but left unattended, it can
hinder brewer performance. De-scaling your
brewer helps maintain the heating element
and other internal parts of the brewer that
come in contact with water. See page 14 for
more information.
13. Storing – When storing your brewer,
empty the Drip Tray. Follow the instructions
on page 14 for emptying the Internal Hot
Water Tank. Store your brewer upright in
a safe, dr y, frost-free environment. See
page 15 for more information.
Power Button (does not illuminate)
Press to turn the brewer power on and off.
Add Water Indicator
Flashing Blue —Fill the Cold Water Reservoir
with cold water until it reaches just under the rim
of the desired level – 6, 8, or 10 oz. of the Water
Level Guide.
Handle Indicator
Flashing Blue — The blue light flashes when the
minimum water amount of 6 oz. has been poured
into the Cold Water Reservoir. After adding your
desired amount of water (10 oz. maximum),
lower the Cold Water Reservoir Lid. The light will
continue to flash until you lift the Handle.
Brew Button
Flashing Blue — Indicates you are ready to brew.
Press the BREW Button.
Flashing Red — Indicates water is heating
(approximately 2 minutes).
Solid Red — Indicates brewing and dispensing of
beverage has begun.
Your Next Brew
When the brewing process is complete, the Add Water
Indicator light will appear. At this point you can begin
making the next beverage, or you can power off.
Automatic Shut-Off
As a safety feature, your brewer will automatically
shut off at any stage when it is idle for longer than 90
seconds. Press the Power Button to restart. If it shut
off while the BREW Button was flashing blue, lift and
lower the Handle to reset.
Drip Tray Overfill Indicator
A red float will appear when the Drip Tray is almost
full. Carefully slide Drip Tray out and empty contents
into the sink.
SECTION 4 Set-Up & Operation
Initial Cleansing & First Brew
CAUTION: Two sharp needles are used to puncture the
K-Cup® packs. One is above the K-Cup® Pack Holder and
the other is in the bottom of the K-Cup® Pack Holder. To
avoid risk of injury, do not put your fingers inside the
K-Cup® Pack Assembly Housing.
For accurate measuring, do not fill if the
Handle is up. In the down position it prevents
water from entering the lower heating
compartment.
MAX
10 oz.
BREW
BREW
CAUTION: During the brewing process, the water
gets extremely hot. To avoid risk of injury, do not
lift the Handle or open the K-Cup
Housing until brewing is complete.
®
Pack Assembly
Remove all tape and cardboard.
1 2
Perform an initial cleansing
brew before making your
first beverage. Follow these
instructions but do not insert
®
a K-Cup
8 9
8
pack.
Plug the Power Cord into an
independent, grounded outlet.
Press the Power Button. The Add Water Indicator
will flash blue.
The Power Button does not illuminate.
3 4
Lift the Cold Water Reservoir Lid.
8 oz.
6 oz.
MIN
Pour water anywhere within the Cold Water
Reser voir until it reaches up to the rim of your
desired fill level on the Water Level Guide
(minimum of 6 oz.). Lower the lid.
For accurate measuring, do not fill if the
Handle is up.
Bottled or filtered water is recommended;
distilled or reverse osmosis water is not.
SECTION 4 Set-Up & Operation (continued)
5 Sec
5
Lift the Handle. Water starts to drain
from the Cold Water Reservoir into
the brewer.
If you add more than 10 oz.,
excess water goes into the
D rip Tray.
Let water fully drain into brewer
before lowering the Handle.
6
Place mug on the Drip Tray.
If you want to use a taller mug,
you can slide the Drip Tray out,
but you will lose the benefit of
the tray to catch the excess
wa te r.
DO NOT remove foil lid or puncture K-Cup
7 8
Insert the K-Cup® pack into the
K-Cup® Pack Holder.
Do not add a K-Cup® pack if
you are performing the initial
cleansing brew.
®
pack.
Wait until all water has drained
(5 seconds) into the brewer
before lowering the Handle
completely.
The BRE W Button will flash blue. Press the
BREW Button.
CAUTION: Do not lift the Handle
!
while brewing.
2 Min
10
The BRE W Button will flash red to
indicate that the water is heating. After
about 2 minutes, the BREW Button will
turn solid red when the beverage starts
to dispense.
®
Remove used K-Cup
CAUTION: K-Cup® pack will be hot.
pack after brewing.
1110
119
Enjoy your beverage! Your brewer is ready to use
again or you can power it off.
As a safety feature, brewer automatically
shuts off after 90 seconds.
If completing the initial cleansing brew,
discard hot water into the sink. Your brewer
is ready to use again.
SECTION 5 Cleaning & Maintenance
Cleaning External Parts
IMPORTANT: Make sure the brewer is unplugged before cleaning.
Regular cleaning of the brewer’s external components is recommended.
• Brewer external housing
• Drip Tray
• Drip Tray Plate
BREWER
• Never immerse brewer in water or other liquids.
• Clean the external housing of the brewer and other external
components with a damp, non-abrasive, lint-free cloth.
DRIP TR AY AND DRIP TRAY PLATE
• When the red Drip Tray Overfill Indicator appears, the Drip Tray is
almost full. Carefully remove by sliding tray toward you. Empty
contents into the sink.
• Inspect the Drip Tray periodically and clean with a damp, non-abrasive,
lint-free cloth.
Do not put the Drip Tray or the Drip Tray Plate in the dishwasher.
Cleaning the K-Cup® Pack Holder Assembly
IMPORTANT: Make sure the brewer is unplugged before cleaning.
K-Cup® Pack Holder Assembly parts include:
• Funnel
• K-Cup® Pack Holder with Exit Needle
The K-Cup® Pack Holder Assembly parts can be placed on
the top shelf of the dishwasher. Use a low temperature cycle
when cleaning.
1. To remove the K-Cup
Holder A ssembly from the brewer,
lift the Handle to open. Grasp the top
of the K-Cup® Pack Holder with one
hand. With the other hand, push up
on the bottom of the K-Cup® Pack
Holder A ssembly until it releases (fig. 1).
®
Pack
fig.
1
2. Separate the Funnel from the K-Cup
snaps free (fig. 2).
3. Clean the Exit Needle on the bottom of the K-Cup® Pack Holder. Insert
a paper clip (fig. 3) or similar tool from below if needle becomes
clogged by coffee grinds.
fig.
2
®
Pack Holder by pulling it until it
fig.
3
Avoid sharp needles in K-Cup®
Pack Assembly Housing. Do
not put your fingers inside the
K-Cup® Pack Assembly Housing.
4. To replace the Funnel, just snap it back into the K-Cup
Pack Holder (fig. 4).
fig.
4
5. To replace the K-Cup
K-Cup® Pack Holder with the opening using the two front
ribs as a guide and snap into place from the top (fig. 5).
fig.
®
Pack Holder Assembly, align the
5
®
12 13
SECTION 5 Cleaning & Maintenance (continued)
Cleaning the Cold Water Reservoir
It is normal over time for discoloration, spotting or staining to appear in
the Cold Water Reservoir. Results will vary depending on the mineral
content of the bottled or filtered water used but will not affect the
operation of the brewer. However, be sure to clean the Cold Water
Reservoir regularly to minimize build-up.
To access the Cold Water Reservoir, lift the lid. Remove the Water Level
Guide (fig. 6) and then clean inside the reservoir with a damp, lint-free cloth
as necessary (fig. 7).
Replace the Water Level Guide and lower the lid when finished.
The Water Level Guide is not dishwasher safe.
fig.
6
fig.
7
Emptying the Internal Hot Water Tank
Brewer must be powered off but plugged in.
• Lower the Cold Water Reservoir Lid.
• Place a mug on the Drip Tray.
• Press and hold down the BREW Button and continue to hold until all
the water is dispensed into the mug.
There will be a 3 to 5 second delay before water begins to dispense.
De-Scaling Your Brewer
Calcium deposits may build up in your brewer, depending on the mineral
content of your water. Scale is non-toxic but if left unattended, it can hinder
brewer performance. De-scaling your brewer helps to maintain the heating
element and other internal parts of the brewer.
The de-scaling process should be done ever y 3 to 6 months to ensure
optimal performance or when there are white deposits in the Cold Water
Reser voir. However, it is possible for calcium deposits to build up faster,
making it necessary to de-scale more often.
To begin, you will need the following:
• 20 oz. of undiluted white vinegar
• 12 oz. ceramic mug (do not use a paper cup)
• Access to a sink
De-Scaling Your Brewer (continued)
FILL, CLEAN AND RINSE
Ste p 1: First Vinegar Rinse
• Fill the Cold Water Reservoir with 10 oz. of undiluted white vinegar.
• Place the ceramic mug on the Drip Tray.
• Lift the Handle, but do not add a K-Cup
• After 5 seconds, lower the Handle.
• Press the flashing blue BRE W Button. It will flash red and then turn
solid red.
• Once the vinegar is dispensed, discard hot contents into sink.
Step 2: Second Vinegar Rinse
• Pour the remaining 10 oz. of vinegar into the Cold Water Reservoir.
• Place the ceramic mug on the Drip Tray.
• Lift the Handle, but do not add a K-Cup
• After 5 seconds, lower the Handle.
• Press the flashing blue BRE W Button. It will then flash red.
• When it turns solid red, power off as it starts to dispense.
• Allow brewer to sit for 30 minutes.
• Power on the brewer, lift and lower the Handle, then press
BREW Button.
• Once the vinegar is dispensed, discard hot contents into sink.
Step 3: Fresh Water Rinse
• Fill the Cold Water Reservoir with 10 oz. of fresh water.
• Place the ceramic mug on the Drip Tray.
• Lift the Handle, but do not add a K-Cup
• Lower the Handle and continue the brewing process until the
hot water is dispensed into the mug. Discard hot contents into sink.
• Repeat this cleansing brew process three (3) more times to cleanse the
brewer plumbing and to remove any residual vinegar taste. The brewer
is now ready for normal use again.
®
pack.
®
pack.
®
pack.
Storage
Empty the Internal Hot Water Tank and Cold Water Reservoir before storing.
See page 14. Store your brewer in a safe, frost-free environment in an
upright position.
Storing the brewer in cold temperatures may cause any residual
condensation to freeze inside the brewer and could cause damage.
Before using your brewer after storage, wipe the Cold Water Reservoir with a
damp, lint-free cloth and run three (3) cleaning brews (without K-Cup®
packs). See page 8 for initial cleansing brew process.
Let brewer rest at room temperature for at least 2 hours before
powering on.
Storing the Power Cord
Behind the brewer is a convenient
compartment to hold the Power
Cord during transport or storage
(fig. 8).
fig.
8
Service
Beyond these recommended cleaning and maintenance procedures, this
brewer is not user serviceable. See page 18 for warranty guidelines. For
service, please refer to the Warranty section in this guide.
1514
SECTION 6 Troubleshooting
SITUATION SOLUTION
Brewer does not have power
BREW Button flashes red too long
Add Water Indicator does not flash blue
Brewer will not brew
• Make sure the Power Button is pressed. The Add Water Indicator should flash blue
after pushing the Power Button. Note that the Power Button does not illuminate.
• During normal operation, the brewer will shut off when it is idle for longer than 90
seconds. Just press the Power Button to restart.
• Plug brewer into an independent outlet.
• Check to be sure that brewer is plugged in securely.
• Plug into a different outlet.
• Reset your home circuit breaker, if necessary.
• If the brewer still does not operate, contact Customer Service.
• Under normal operation, the BREW Button will flash red when the brewer is heating and
will turn solid red when brewing. If the BREW Button flashes red longer than 3 minutes,
contact Customer Service.
• If the Add Water Indicator does not flash blue, make sure the brewer has power (see above).
• Water may be in the Cold Water Reservoir and brewer. First, try raising the Handle to
drain all water from the Cold Water Reservoir into the brewer. If the light still does not flash,
power off and place a mug on the Drip Tray. Hold down the BREW Button and continue to
hold down until all the water is dispensed into the mug.
• If the brewer still does not operate, contact Customer Service.
• Make sure the brewer has power (see above).
• If using reverse osmosis or distilled water, the brewer may not operate correctly. See page 14 for
emptying the Internal Hot Water Tank and then use filtered or bottled water.
• Press the Power Button. If the Add Water Indicator flashes blue, add water and attempt
to brew. If the brewer loses power during the brew process, the brewer may need to be
re-set when power is restored. To re-set, simply lift and lower the Handle.
• Check that the minimum water level of 6 oz. has been poured into the Cold Water Reservoir.
SITUATION SOLUTION
Brewer will not brew when used for the first time
Brewer only brews a partial brew
Brewer shuts off automatically
There is water in the Drip Tray
Red Indicator appears in Drip Tray
• Brewer may be cold or frozen. Let brewer rest at room temperature for at least 2
hours before powering on.
• Make sure the brewer has power (see previous page).
• Allow enough time for water in the Cold Water Reservoir to drain completely into the brewer.
• The Exit Needle may be clogged (see page 12).
• Clean the K-Cup
• De-scale the brewer (see page 14).
• If you have repeated the de-scale procedure two times and the brewer still does not
function properly, contact Customer Service.
• Under normal operation, the brewer will shut off when it is idle for longer than 90 seconds.
Just press the Power Button to restart.
• If the brewer shuts off in the middle of a brew (not from power outage), contact Customer Ser vice.
• Remember that any liquid overflow (from your cup or the Cold Water Reservoir) will be
caught in the Drip Tray.
• When the Drip Tray is almost full, the red Drip Tray Overflow Indicator will appear. Carefully
remove the Drip Tray and empty its contents into the sink.
• This means that the Drip Tray is almost full. Carefully remove the Drip Tray and empty its
contents into the sink.
Should other issues arise with your brewer, please call
Keurig Customer Service at 1.866.901.BREW (2739).
®
Pack Assembly, if necessary (see page 12).
16 17
SECTION 7 Warranty
Limited One Year Warranty
Keurig, Incorporated warrants that your brewer will be free of defects in
materials or workmanship under normal home use for one year from the date
of purchase. It is recommended that you fill out and return the warranty card
enclosed with your brewer so that your purchase information will be stored
in our system. Keurig will, at its option, repair or replace a defective brewer
without charge upon its receipt of proof of the date of purchase. If a
replacement brewer is necessary to service this warranty, the replacement
brewer may be new or reconditioned. If a replacement brewer is sent, a new
limited one year warranty will be applied to the replacement brewer.
This warranty only applies to brewers operated in the United States and
Canada. This warranty gives you specific legal rights, and you may also have
other rights that vary from state to state and, in the case of Canada, from
province to province.
Only the use of Keurig Brewed
guarantee the proper functioning and lifetime of your Keurig® brewer.
Any damage to or malfunction of your brewer resulting from the use of non
Keurig Brewed® K-Cup® brand packs and accessories may not be covered
by this warranty or may result in a service fee if the damage or malfunction is
determined to be caused by such use.
What is not covered by the limited warrant y?
THIS WARRANTY DOES NOT COVER CONSEQUENTIAL OR INCIDENTAL
DAMAGES SUCH A S PROPERTY DAMAGE AND DOES NOT COVER
INCIDENTAL COSTS AND EXPENSES RESULTING FROM ANY BRE ACH
OF THIS WARRANTY, EVEN IF FORESEEABLE. Some states or provinces
do not allow the exclusion or limitations of incidental or consequential
damages, so the above limitation or exclusion may not apply to you
depending on the state or province of purchase.
®
K-Cup® brand packs and accessories will
Scan. Click. Call!
Learn more and reach us quickly without leaving home.
Nor does this warranty cover damages caused by non Keurig Brewed
K-Cup® brand packs or accessories, services performed by anyone other
than Keurig or its authorized service providers, use of parts other than
genuine Keurig® parts, or external causes such as abuse, misuse,
inappropriate power supply or acts of God.
Other limitations
THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER EXPRESS
WARRANTY, WHETHER WRITTEN OR ORAL. IN ADDITION, KEURIG HEREBY
SPECIFICALLY DISCLAIMS ALL OTHER WARRANTIES WITH RESPECT TO
YOUR K10 MINI PLUS BREWER, INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR ANY PARTICUL AR PURPOSE. Some
states or provinces do not allow disclaimers of such implied warranties or
limitations on how long an implied warranty lasts, so the above limitation
may not apply to you depending on the state or the province of purchase.
How do you obtain warranty service?
Keurig® brewers are high-quality appliances and, with proper care, are
intended to provide years of satisfying performance. However, should the
need arise for warranty servicing, simply call Keurig Customer Service at
our toll free phone number 1.866.901.BREW (2739). Please do not return your
brewer for servicing without first speaking to Keurig Customer Service to
obtain an Authorization to Return number (ATR). Keurig® brewers returned
without an ATR number will be returned to the sender without servicing.
Keurig, Incorporated
55 Walkers Brook Drive
Reading, MA 01867
1.866.9 01.BREW (2739)
18 19
®
Scan here for videos about caring for your brewer!
Scan this QR code with your smartphone for step-by-step videos on
cleaning, de-scaling and more. Or if you prefer, you can watch the videos
on your computer at bit.ly/NjTZ8W
Have questions? We’re here to help!
Keurig is committed to your satisfaction. If you have questions, just give
us a call to have them answered quickly without leaving the comfort of
your home. 1.866.901.BREW (2739)
To learn more about Keurig, visit www.keurig.com or call 1.866.901.BREW (2739)
P/N 60-202467-000 Rev A
08/12
Keurig, Incorporated
55 Walkers Brook Drive
Reading, MA 01867
Keurig, Incorporated is a wholly-owned
subsidiary of Green Mountain Coffee Roasters, Inc.
For Household Use Only
Pat. ww w.GMCR.com/patents
© 2012 Keur ig, Incorpor ated
All rig hts reser ved
Loading...