Kenwood KMM-BT302 User Manual

KMM-BT302

DIGITAL MEDIA RECEIVER

INSTRUCTION MANUAL

CONTENTS BEFORE USE

BEFORE USE 2

BASICS 3

GETTING STARTED 4

1 Select the display language

and cancel the demonstration 2 Set the clock and date 3 Set the initial settings

RADIO 6

AUX 7

USB / iPod / ANDROID 8

Pandora® 10

(Not applicable for Korean models)

BLUETOOTH® 11

AUDIO SETTINGS 17

DISPLAY SETTINGS 20

TROUBLESHOOTING 21

REFERENCES 23

Maintenance More information

INSTALLATION / CONNECTION 25

SPECIFICATIONS 27

IMPORTANT

• To ensure proper use, please read through this manual before using this product. It is especially important that you read and observe Warning and Caution in this manual.

• Please keep the manual in a safe and accessible place for future reference.

Warning

Do not operate any function that takes your attention away from safe driving.

Caution

Volume setting:

• Adjust the volume so that you can hear sounds outside the car to prevent accidents.

• Lower the volume before playing digital sources to avoid damaging the speakers by the sudden increase of the output level.

General:

• Avoid using the external device if it might hinder safe driving.

•

Make sure all important data has been backed up. We shall bear no responsibility for any loss of recorded data.

•

Never put or leave any metallic objects (such as coins or metal tools) inside the unit to prevent a short circuit.

• USB rating is indicated on the main unit. To view, detach the faceplate.

• Depending on the types of cars, the antenna will automatically extend when you turn on the unit with the antenna control wire connected ( parking at a low ceiling area.

Remote control (RC-406):

• Do not leave the remote control in hot places such as on the dashboard.

• The Lithium battery is in danger of explosion if replaced incorrectly. Replace it only with the same or equivalent type.

• The battery pack or batteries shall not be exposed to excessive heat such as sunshine, fire or the like.

• Keep the battery out of reach of children and in its original packaging when not in used. Dispose of used batteries promptly. If swallowed, contact a physician immediately.

How to read this manual

• Operations are explained mainly using buttons on the faceplate.

• English indications are used for the purpose of explanation. You can select the display language from the [

FUNCTION

• [

] indicates the selected items.

• (

XX) indicates references are available on the stated page.

] menu. ( 5)

( 3)

26). Turn off the unit or change the source to STANDBY when

BASICS

Faceplate

Remote control (RC-406)

Volume knob

Detach button

To On the faceplate On the remote control

Turn on the power

Adjust the volume Turn the volume knob. Press

Select a source

Change the display information Press DISP repeatedly. (

Display window

Lights up when Bluetooth connection is established. (

Flashes when the unit enters searching status.

How to resetAttach Detach

Press the switch twice within 5seconds after detaching the faceplate.

Press

• Press and hold to turn off the power.

Press

repeatedly.

24) ( Not available )

12)

How to replace the battery

Press and hold SRC to turn off the power. ( Pressing SRC does not turn on the power. )

or .

Press ATT during playback to attenuate the sound.

• Press again to cancel.

Press SRC repeatedly.

Remote sensor (Do not expose to bright sunlight.)

Pull out the insulation sheet when using for the first time.

ENGLISH

GETTING STARTED

Select the display language and cancel the demonstration

When you turn on the power for the first time (or [

RESET

] is set to [

“PRESS” “VOLUME KNOB”

1 Turn the volume knob to select [

(Turkish), then press the knob.

[

ENG

Then, the display shows: “CANCEL DEMO”

“VOLUME KNOB”.

YES

], 5), the display shows: “SEL LANGUAGE”

] is selected for the initial setup.

ENG

2 Press the volume knob.

[

YES

] is selected for the initial setup.

3 Press the volume knob again.

“DEMO OFF” appears.

Then, the display shows the selected crossover type: “2-WAY X ’ OVER” or “3-WAY X ’ OVER”

• To change the crossover type, see “Change the crossover type” (

5).

FACTORY

] (English) or [

“PRESS”

TUR

Set the clock and date

Press the volume knob to enter [

1 2 Turn the volume knob to select [

To adjust the clock

3 Turn the volume knob to select [

FUNCTION

CLOCK

], then press the knob.

CLOCK ADJUST

], then press the knob.

4 Turn the volume knob to make the settings, then press the knob.

Hour

5 Turn the volume knob to select [ 6 Turn the volume knob to select [

To set the date

7 Turn the volume knob to select [ 8 Turn the volume knob to select [ 9 Turn the volume knob to select [

]

10 Turn the volume knob to make the settings, then press the knob.

Day

Minute

Month Year or Month Day Year

CLOCK FORMAT 12H

] or [

24H

DATE FORMAT DD/MM/YY DATE SET

], then press the knob.

] or [

11 Press and hold to exit.

To return to the previous setting item, press .

Set the initial settings

Press repeatedly to enter STANDBY.

1 2 Press the volume knob to enter [ 3 Turn the volume knob to select an item (

FUNCTION

5)

, then press the knob.

4 Repeat step 3 until the desired item is selected or activated. 5 Press and hold to exit.

To return to the previous setting item, press .

MM/DD/YY

], then press the knob.

GETTING STARTED

AUDIO CONTROL

SWITCH PREOUT*

DISPLAY

EASY MENU

TUNER SETTING

PRESET TYPE

SYSTEM

KEY BEEP*

TDF ALARM* ON

SOURCE SELECT

PANDORA SRC

BUILT-IN AUX ON

F/W UPDATE

UPDATE SYSTEM

F/W UP xx.xx

FACTORY RESET YES

REAR/ SUB-W

connected to the line out terminals on the rear (through an external amplifier).

:Both display and button illuminations change to white color when entering [ remain as [

NORMAL

(FM1/ FM2/ FM3/ AM/ SW1/ SW2).; each preset button, regardless of the selected band.

:Activates the keypress tone.;

: Activates the alarm if you forget to detach the faceplate when ACC is set to OFF.;

:Enables PANDORA in source selection.;

:Enables AUX in source selection.;

YES

:Starts upgrading the firmware.; NO:Cancels (upgrading is not activated). For details on how to update the firmware, see: www.kenwood.com/cs/ce/

:Resets the settings to default (except the stored station).;

:Cancels.

Default:

: Selects whether rear speakers or a subwoofer are

FUNCTION

].;

OFF

COLORSELECT

:Memorizes one station for each preset button in each band

OFF

:Both display and button illuminations

] color. ( 20)

MIX

OFF

:Deactivates.

: Deactivates.

OFF

:Memorizes one station for

OFF

:Disables. ( 10)

:Disables. ( 7)

CLOCK

CLOCK DISPLAY

ENGLISH

TURKCE

Not applicable if 3-way crossover is selected.

:The clock time is shown on the display even when the unit is

turned off.;

OFF

:Cancels.

Select the display language for [ information if applicable. By default, [

ENGLISH

] is selected.

FUNCTION

] menu and music

Change the crossover type

Press repeatedly to enter STANDBY.

1 2 Press and hold number buttons 4 and 5 to enter crossover select.

The current crossover type appears.

3 Turn the volume knob to select “2WAY” or “3WAY”, then press the

knob.

4 Turn the volume knob to select “YES” or “NO”, then press the knob.

The selected crossover type appears.

• To cancel, press and hold

• To adjust the selected crossover settings, (

18).

Caution

Select a crossover type according to how the speakers are connected. (

26)

If you select a wrong type:

• The speakers may damage.

• The output sound level may be extremely high or low.

ENGLISH

RADIO

Search for a station

Press repeatedly to select TUNER.

1 2 Press repeatedly (or press / on RC-406) to

select FM1/ FM2/ FM3/ AM/ SW1/ SW2.

3 Press S/T (or press S/ on RC-406) to search for a

station.

• To change the searching method for S/T: Press

repeatedly. AUTO1 : Automatically search for a station. AUTO2 : Search for a preset station. MANUAL : Manually search for a station.

• To store a station: Press and hold one of the number buttons (1to6).

• To select a stored station: Press one of the number buttons (1to6) (or

press one of the number buttons (1to6) on RC-406).

Direct Access Tuning (using RC-406)

Press DIRECT to enter Direct Access Tuning.

1 2 Press the number buttons to enter a frequency. 3 Press to search for a station.

• To cancel, press or DIRECT.

• If no operation is done for 10seconds after step

is automatically canceled.

2, Direct Access Tuning

Other settings

Press the volume knob to enter [

FUNCTION

2 Turn the volume knob to select an item (see the following table),

then press the knob.

3 Repeat step 2 until the desired item is selected or activated. 4 Press and hold to exit.

To return to the previous setting item, press .

Default:

TUNER SETTING

LOCAL SEEK

AUTO MEMORY

MONO SET ON

NEWS SET ON

REGIONAL ON

AF SET ON

TI ON

:Searches only AM/ SW1/ SW2 stations with good reception. ;

OFF

:Cancels.

•

Settings made are applicable only to the selected source/station. Once

you change the source/station, you need to make the settings again.

YES

:Automatically starts memorizing 6 stations with good reception.;

:Cancels.

•

Selectable only if [

:Improves the FM reception, but the stereo effect may be lost.;

OFF

:Cancels.

: The unit will temporarily switch to News Programme if available. ;

OFF

: Cancels.

: Switches to another station only in the specific region using the “AF”

control.;

: Automatically searches for another station broadcasting the same program in the same Radio Data System network with better reception when the current reception is poor.;

:Allows the unit to temporarily switch to Traffic Information if available (“TI” lights up).;

OFF

:Cancels.

OFF

NORMAL

:Cancels.

] is selected for [

OFF

:Cancels.

PRESET TYPE

]. ( 5)

RADIO

PTY SEARCH1 Press the volume knob to enter PTY language selection.

CLOCK

TIME SYNC

Turn the volume knob to select the PTY language (

GERMAN

ON OFF

), then press the knob.

Turn the volume knob to select the available Program Type (see the

following).

Press to start searching.

:Synchronizes the unit’s time to the Radio Data System station time.;

:Cancels.

ENGLISH/ FRENCH

AUX

Preparation:

Select [

] for [

BUILT-IN AUX

Start listening

Connect a portable audio player (commercially available).

Auxiliary input jack

]. ( 5)

Portable audio player

Available Program Type for PTY SEARCH

SPEECH : NEWS, AFFAIRS, INFO

CULTURE, SCIENCE, VARIED, WEATHER, FINANCE, CHILDREN, SOCIAL RELIGION, PHONE IN, TRAVEL, LEISURE, DOCUMENT

MUSIC

POP M

(music),

CLASSICS, OTHER M OLDIES, FOLK M

The unit will search for the Program Type categorized under [ [

MUSIC

] if selected.

MONO SET

]/ [

• [ only when the band is FM1/ FM2/ FM3.

• If the volume is adjusted during reception of traffic information, alarm or news bulletin, the adjusted volume is memorized automatically. It will be applied the next time traffic information, alarm or news bulletin is turned on.

NEWS SET

(information),

ROCK M

(music),

(music)

]/ [

REGIONAL

SPORT, EDUCATE, DRAMA

(music),

EASY M

JAZZ, COUNTRY, NATION M

]/ [

AF SET

(music),

]/ [TI]/ [

LIGHT M

PTY SEARCH

(music),

SPEECH

] is selectable

] or

3.5mm stereo mini plug with “L” shaped connector (commercially available)

2 Press repeatedly to select AUX. 3 Turn on the portable audio player and start playback.

Set the AUX name

While listening to a portable audio player connected to the unit...

1 Press the volume knob to enter [ 2 Turn the volume knob to select [ 3 Turn the volume knob to select [

FUNCTION

SYSTEM

], then press the knob.

AUX NAME SET

], then press the knob.

4 Turn the volume knob to select an item, then press the knob.

AUX

(default)/

DVD/ PORTABLE/ GAME/ VIDEO/ TV

5 Press and hold to exit.

To return to the previous setting item, press .

ENGLISH

USB / iPod / ANDROID

Start playback

The source changes automatically and playback starts.

USB input terminal

USB

CA-U1EX (max.: 500mA) (optional accessory)

iPod/iPhone

KCA-iP102 / KCA-iP103 (optional

accessory) of the iPod/iPhone

KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type

Do not leave the cable inside the car when not using.

or accessory cable

ANDROID

Micro USB 2.0 cable (commercially available)

To On the faceplate On the remote control

Playback / pause Press .

Reverse / Fast-forward

Select a track/file

Select a folder

Repeat play

Press and hold S/T. Press and hold S/ .

Press S/T. Press S/

Press J/K.

Press repeatedly.

FILE REPEAT/ FOLDER REPEAT/ ALL REPEAT FILE REPEAT/ FOLDER REPEAT/ REPEAT OFF

Random play

Press repeatedly.

FOLDER RANDOM/ RANDOM OFF

Press

/ .

: MP3/WMA/AAC/WAV/FLAC file : iPod or ANDROID

: MP3/WMA/AAC/WAV/FLAC file, iPod or

ANDROID

Press and hold

When connecting an Android device, “Press [VIEW] to install KENWOOD MUSIC PLAY APP” is shown. Follow the instructions

to select

ALL RANDOM

to install the application. You can also install the latest version of KENWOOD MUSIC PLAY application on your Android device before connecting. (

For ANDROID: Applicable only when [

Only for MP3/WMA/AAC/WAV/FLAC files. This does not work for iPod/ ANDROID.

For iPod/ ANDROID: Applicable only when [

Only for MP3/WMA/AAC/WAV/FLAC files.

23)

BROWSE MODE

MODE OFF

] is selected. ( 9)

]/ [

BROWSE MODE

] is selected. ( 9)

USB / iPod / ANDROID

Select control mode

While in IPOD source, press 5 repeatedly.

MODE ON

: Control iPod using the iPod itself. However, you can

still play/pause, file skip, fast-forward or reverse from

MODE OFF

While in ANDROID source, press 5 repeatedly.

BROWSE MODE

HAND MODE

this unit.

: Control iPod from this unit.

: Control Android device from this unit via

KENWOOD MUSIC PLAY application installed in the Android device.

: Control Android device using the Android

device itself via other media player applications installed in the Android device. However, you can still play/pause and file skip from this unit.

Select music drive

Press 5 repeatedly.

Stored songs in the following drive will be played back.

• Selected internal or external memory of a smartphone (Mass Storage Class).

• Selected drive of a multiple drives device.

Listen to TuneIn Radio/ TuneIn Radio Pro/ Aupeo

While listening to TuneIn Radio, TuneIn Radio Pro or Aupeo, connect the iPod/iPhone to the USB input terminal of the unit.

• The unit will output the sound from these applications.

Select a file from a folder/list

Press .

1 2 Turn the volume knob to select a folder/list, then press the knob. 3 Turn the volume knob to select a file, then press the knob.

Quick Search

If you have many files, you can search through them quickly.

Turn the volume knob quickly to browse through the list quickly.

–

Not applicable for iPod.

(or)

Press S/T to search at a preset skip search ratio. (

• Pressing and holding S/T searches at a 10

– Not applicable for MP3/ WMA/ AAC/ WAV/ FLAC files.

(or)

Alphabet search

If you have many files in the iPod, you can search through them quickly according to the first character of the file name.

(applicable only for iPod)

ratio.

10, [SKIP SEARCH

Turn the volume knob quickly to enter character search. Turn the volume knob to select the character.

To search for a character other than A to Z and 0to9, enter only “ * ”.

Press S/T to move to the entry position.

• You can enter up to 3characters.

Press the volume knob to start searching.

• To return to the root folder/ first file/ top menu, press 5. (

source.

)

• To return to the previous setting item, press

• To cancel, press and hold

• For iPod, applicable only when [

• For ANDROID, applicable only when [

MODE OFF

BROWSE MODE

] is selected.

Not applicable for BT AUDIO

] is selected.

])

ENGLISH

USB / iPod / ANDROID

Direct Music Search (using RC-406)

Press DIRECT.

1 2 Press the number buttons to enter a track/file

number.

3 Press to search for music.

• To cancel, press or DIRECT.

• Not available if Random Play is selected.

• Not applicable for iPod and ANDROID.

Other settings

Press the volume knob to enter [

1 2 Turn the volume knob to select an item (see

the following table), then press the knob.

3 Repeat step 2 until the desired item is selected

or activated.

4 Press and hold to exit.

To return to the previous setting item, press .

USB

MUSIC DRIVE DRIVE CHANGE

SKIP SEARCH 0.5%/ 1%/ 5%/ 10%

to [

DRIVE 4

]) is selected automatically and playback starts. Repeat steps drives.

or ANDROID, selects the skip search ratio over the total files.

to 3 to select the following

FUNCTION

:The next drive ([

: While listening to iPod

Default:

DRIVE 1

]

Pandora®

Preparation:

Install the latest version of the Pandora application on your device (iPhone/ iPod touch), then create an account and log in to Pandora.

• Select [

(Not applicable for Korean models)

] for [

PANDORA SRC

]. ( 5)

Start listening

Open the Pandora application on your device.

1 2 Connect your device to the USB input terminal.

USB input terminal

KCA-iP102 / KCA-iP103 (optional accessory) or accessory cable of the iPod/iPhone

3 Press repeatedly to select PANDORA.

Broadcast starts automatically.

To On the faceplate On the remote control

Playback / pause

Skip a track

Thumbs up or thumbs down

KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type

Do not leave the cable inside the car when not using.

If thumbs down is selected, the current track is skipped.

Press

Press T.

Press J/K.

. Press

Press

Create and save a new station

Press .

1 2 Turn the volume knob to select [ 3 Turn the volume knob to select [

A new station is created based on the current song or artist.

NEW STATION FROM TRACK

], then press the knob.

] or [

FROM ARTIST

], then press the knob.

4 Press and hold one of the number buttons (1to5) to store.

To select a stored station, press one of the number buttons (1to5).

/ .

Pandora®

(Not applicable for Korean models)

Search for a registered station

Press .

1 2 Turn the volume knob to select an item, then press the knob.

[

SORT BY DATE

[

SORT BY A-Z

]:According to the registered date

]:Alphabetical order

3 Turn the volume knob to select the desired station, then press the knob.

To cancel, press and hold .

(or using RC-406)

Press J / K to search for a station, then press .

BLUETOOTH®

BLUETOOTH — Connection

Supported Bluetooth profiles

– Hands-Free Profile (HFP) – Advanced Audio Distribution Profile (A2DP) – Audio/Video Remote Control Profile (AVRCP) – Serial Port Profile (SPP) – Phonebook Access Profile (PBAP)

Supported Bluetooth codecs

– Sub Band Codec (SBC) – Advanced Audio Coding (AAC)

Bookmark current song information

Press and hold the volume knob.

“BOOKMARKED” appears and the information is stored to your device. The bookmark is available on your Pandora account but not on this unit.

Delete a station

While listening to PANDORA...

1 Press the volume knob to enter [ 2 Turn the volume knob to select [ 3 Turn the volume knob to select [ 4 Turn the volume knob to select [

FUNCTION

SYSTEM

], then press the knob.

STATION DEL SORT BY A-Z

], then press the knob.

] or [

SORT BY DATE

], then press the knob.

5 Turn the volume knob to select the desired station to delete, then press the knob. 6 Turn the volume knob to select [

YES

], then press the knob.

7 Press and hold to exit.

To return to the previous setting item, press .

Connect the microphone

Rear panel

Microphone input jack

Adjust the microphone angle

Secure using cord clamps (not supplied) if necessary.

Microphone (supplied)

ENGLISH

BLUETOOTH®

Pair and connect a Bluetooth device for the first time

Press to turn on the unit.

1 2 Search and select this unit model name (KMM-BT30

“PAIRING”

the display.

“PASS XXXXXX” Device name “PRESS” “VOLUME KNOB” scrolls on

• For some Bluetooth devices, you may need to enter the Personal Identification

Number (PIN) code immediately after searching.

3 Press the volume knob to start pairing.

“PAIRING OK” appears when pairing is completed.

• This unit supports Secure Simple Pairing (SSP).

• Up to 10 devices can be registered (paired) in total.

• Once the pairing is completed, the Bluetooth device will remain registered in the unit even if you reset the unit. To delete the paired device,

Once pairing is completed, Bluetooth connection is established automatically.

• “BT1” and/or “BT2” indicator on the faceplate lights up.

• A maximum of two Bluetooth phones and one Bluetooth audio device can be connected at any time.

• Some Bluetooth devices may not automatically connect to the unit after pairing. Connect the device to the unit manually.

• Refer to the instruction manual of the Bluetooth device for more information.

Auto Pairing

When you connect iPhone/ iPod touch/ Android device to the USB input terminal, pairing request (via Bluetooth) is automatically activated.

Press the volume knob to pair once you have confirmed the device name.

Automatic pairing request is activated only if: – Bluetooth function of the connected device is turned on. – [

AUTO PAIRING

– KENWOOD MUSIC PLAY application is installed on the Android device (

[

BROWSE MODE

] is set to [ON]. ( 15)

] is selected ( 9).

) on the Bluetooth device.

15, [

DEVICE DELETE

8) and

BLUETOOTH — Mobile phone

Receive a call

When there is an incoming call:

• ZONE 2 illuminates in green color and flashes.

• The unit answers the call automatically if [ is set to a selected time. (

During a call:

• The display illuminates according to the settings made for [

DISPLAY

color.

• If you turn off the unit or detach the faceplate, the Bluetooth connection is disconnected.

] ( 20) and ZONE 2 illuminates in green

14)

AUTO ANSWER

]

BLUETOOTH®

The following operations may differ or not available depending on the connected phone.

To On the faceplate On the remote control

First incoming call...

Answer a call

Reject a call

End a call

While talking on the first incoming call...

Answer another incoming call and hold the current call

Reject another incoming call

While having two active calls...

End current call and activate held call

Swap between the current call and held call

Adjust the phone volume

[00]

[35]

(Default:

Switch between hands-free and private talk modes

[15]

Press or one of the number buttons (1 to 6).

Press

Turn the volume knob during

)

a call.

• This adjustment will not affect the volume of the other sources.

Press

• Operations may vary according to the connected Bluetooth device.

or the volume knob

. Press .

during a call.

Press

( Not available )

Improve the voice quality

While talking on the phone...

1 Press the volume knob to enter [

FUNCTION

2 Turn the volume knob to select an item (see the

following table), then press the knob.

3 Repeat step 2 until the desired item is selected or

activated.

4 Press and hold to exit.

To return to the previous setting item, press .

Default:

MIC GAIN –10

NR LEVEL –5

ECHO CANCEL –5

—

+10(–4

increases as the number increased.

—+5(0):Adjust the noise reduction level until the least noise is being heard during a phone conversation.

—+5(0):Adjust the echo cancellation delay time until the least echo is being heard during a phone conversation.

):The sensitivity of the microphone

Make the settings for receiving a call

Press to enter Bluetooth mode.

1 2 Turn the volume knob to select an item ( 

press the knob.

), then

3 Repeat step 2 until the desired item is selected or

activated.

4 Press and hold to exit.

To return to the previous setting item, press .

ENGLISH

BLUETOOTH®

Default:

SETTINGS

AUTO ANSWER

BATT/SIGNAL* AUTO

Functionality depends on the type of the phone used.

Make a call

You can make a call from the call history, phonebook, or dialing the number. Call by voice is also possible if your mobile phone has the feature.

1 Press to enter Bluetooth mode. 2 Turn the volume knob to select an item (see the following table),

then press the knob.

3 Repeat step 2 until the desired item is selected/activated or follow

the instructions stated on the selected item.

4 Press and hold to exit.

To return to the previous setting item, press .

CALL HISTORY

—30:The unit answers incoming call automatically in the selected

time (in seconds).;

:Shows the strength of the battery and signal when the unit

detects a Bluetooth device and the Bluetooth device is connected.;

OFF

:Cancels. Clock time is shown.

(Applicable only if the phone supports PBAP)

Press the volume knob to select a name or a phone number.

• “INCOMING”, “OUTGOING”, or “MISSED” is shown on the lower part of the display to indicate the previous call status.

• Press

• “NO DATA” appears if there is no recorded call history.

Press the volume knob to call.

OFF

:Cancels.

DISP

to change the display category (NUMBER or NAME).

PHONE BOOK

NUMBER DIAL1 Turn the volume knob to select a number (0 to 9) or character ( , #,

VOICE

BATT LOW/ MID/ FULL*:Shows the strength of the battery.

NO SIGNAL/ LOW/ MID/ MAX*:Shows the strength of the current received signal.

Functionality depends on the type of the phone used.

(Applicable only if the phone supports PBAP)

Turn the volume knob quickly to enter alphabet search mode (if the

phonebook contains many contacts).

The first menu (ABCDEFGHIJK) appears.

• To go to the other menu (LMNOPQRSTUV or WXYZ1

J / K

• To select the desired first letter, turn the volume knob or press

Select “1” to search with numbers and select “

2 3

•

Press

Press the volume knob to call.

Press the number buttons (0 to 9) to enter the phone number.

Press to call.

Speak the name of the contact you want to call or the voice command to control the phone functions. (

S / T

symbols. Turn the volume knob to select a name, then press the knob. Turn the volume knob to select a phone number, then press the knob

to call.

The phonebook of the connected phone is automatically transferred to

the unit when pairing. Contacts are categorized as: HOME, OFFICE, MOBILE, OTHER, GENERAL This unit can display only non-accent letters. (Accent letters such as

“Ú” is showns as “U”.)

+).

Repeat steps

(or using RC-406)



15, Make a call using voice recognition

, then press the knob.

S / T

to move the entry position.

and 2 until you finish entering the phone number.

)

), press

” to search with

BLUETOOTH®

Make a call using voice recognition

Press and hold to activate the voice recognition of the

connected phone.

2 Speak the name of the contact you want to call or the voice

command to control the phone functions.

• Supported Voice Recognition features vary for each phone. Refer to the instruction manual of the connected phone for details.

• This unit also supports the intelligent personal assistant function of iPhone.

Settings in memory

Store a contact in memory

You can store up to 6 contacts into the number buttons (1 to 6).

1 Press to enter Bluetooth mode. 2 Turn the volume knob to select [

[

NUMBER DIAL

], then press the knob.

CALL HISTORY

], [

PHONE BOOK

], or

3 Turn the volume knob to select a contact or enter a phone

number.

If a contact is selected, press the volume knob to show the phone

number.

4 Press and hold one of the number buttons (1 to 6).

“STORED” appears when the contact is stored. To erase a contact from the preset memory, select [

step

2 and store a blank number.

NUMBER DIAL

] in

Make a call from memory

Press to enter Bluetooth mode.

1 2 Press one of the number buttons (1 to 6). 3 Press the volume knob to call.

“NO MEMORY” appears if there is no contacts stored.

Other settings

Press the volume knob to enter

[FUNCTION

2 Turn the volume knob to select an item (see the following table), then

press the knob.

3 Repeat step 2 until the desired item is selected/activated or follow the

instructions stated on the selected item.

4 Press and hold to exit.

To return to the previous setting item, press .

Default:

BT MODE

PHONE SELECT

AUDIO SELECT

DEVICE DELETE

PIN CODE EDIT (0000)

RECONNECT ON

AUTO PAIRING ON

INITIALIZE YES

Selects the phone or audio device to connect or disconnect. “

” appears in front of the device name when connected.

•

You can only connect a maximum of two Bluetooth phones and one

Bluetooth audio device at any time.

Turn the volume knob to select a device to delete, then press the knob.

Turn the volume knob to select [

Changes the PIN code (up to 6 digits).

Turn the volume knob to select a number.

Press S/T to move the entry position.

Repeat steps

Press the volume knob to confirm.

:The unit automatically reconnect when the last connected Bluetooth

device is within range.;

:The unit automatically pair supported Bluetooth device (iPhone/ iPod touch/ Android device) when it is connected through USB input terminal.Depending on the operating system of the connected device, this function may not work. ;

:Initializes all the Bluetooth settings (including stored pairing,

phonebook, and etc.).;

and 2 until you finish entering the PIN code.

OFF

:Cancels.

YES

] or [NO], then press the knob.

ENGLISH

BLUETOOTH®

Bluetooth test mode

You can check the connectivity of the supported profile between the Bluetooth device and the unit.

• Make sure there is no Bluetooth device paired.

1 Press and hold .

“PLEASE PAIR YOUR PHONE PIN 0000” appears.

2 Search and select this unit model name

(KMM-BT30

3 Operate the Bluetooth device to confirm

pairing.

“TESTING” flashes on the display.

The connectivity result (OK or NG) appears after the test.

PAIRING: Pairing status HF CNT: Hands-Free Profile (HFP) compatibility AUD CNT: Advanced Audio Distribution Profile

PB DL: Phonebook Access profile (PBAP)

To cancel test mode, press and hold off the unit.

) on the Bluetooth device.

(A2DP) compatibility

compatibility

to turn

BLUETOOTH — Audio

Audio player via Bluetooth

Press repeatedly to select BTAUDIO (or press SRC on RC-406).

1 2 Operate the Bluetooth audio player to start playback.

To On the faceplate On the remote control

Playback / pause

Select group or folder

Reverse / Forward skip

Reverse / Fast-forward

Repeat play Press

Random play Press and hold

Select a file from a folder/list

Operations and display indications may differ according to their availability on the connected device.

Press

Press J / K.

Press S/T. Press S/

Press and hold S/T. Press and hold S/

ALL REPEAT, FILE REPEAT, REPEAT OFF

ALL RANDOM

• Press

Refer to “Select a file from a folder/list” on page 9.

. Press

Press

repeatedly.

to select

RANDOM OFF

( Not available )

/ .

BLUETOOTH®

Internet radio via Bluetooth

Listen to Pandora

You can listen to Pandora on the Android device via Bluetooth on this unit.

Preparation:

Select [

] for [

PANDORA SRC

1 Open the Pandora application on your device. 2 Connect your Bluetooth audio player via

Bluetooth connection. (

3 Press repeatedly to select PANDORA.

The source switches and broadcast starts

automatically.

You can operate Pandora in the same way as Pandora for iPod/iPhone. (

]. ( 5)

12)

10)

AUDIO SETTINGS

While listening to any source...

1 Press the volume knob to enter [ 2 Turn the volume knob to select [ 3 Turn the volume knob to select an item (see the following table), then press the knob. 4 Repeat step 3 until the desired item is selected or activated. 5 Press and hold to exit.

(or using RC-406)

1 Press AUD to enter [

AUDIO CONTROL

2 Press J / K to select an item, then press .

To return to the previous setting item, press

SUB-W LEVEL –50

MANUAL EQ

BAND1 LEVEL LEVEL

BAND2 LEVEL BAND13 LEVEL

Q FACTOR 1.35/ 1.50/ 2.00

PRESET EQ NATURAL/ ROCK/ POPS/ EASY/ TOP40/ JAZZ/ POWERFUL/ USER

BASS BOOST LEVEL1/ LEVEL2/ LEVEL3/ LEVEL4/ LEVEL5

LOUDNESS LEVEL1/ LEVEL2

SUBWOOFER SET ON

+10 (0

BASS EXTEND ON

–9

to +9 (0): The sound elements (frequency level, tone level, Q factor) are preset into each

selection (

BAND1 LEVEL

Adjusts the level to memorize for each source. (Before making an adjustment, select the source you want to adjust.)

suitable to the music genre. (Select [

OFF

:Cancels.

balanced sound at a low volume level.;

:Turns on the subwoofer output.;

FUNCTION

AUDIO CONTROL

): Adjusts the subwoofer output level.

–9

to +9 (0):(Refer to

:Turns on the extended bass.;

BAND13 LEVEL

:Adjust the quality factor.

:Selects your preferred low and high frequencies boost to produce a well-

], then press the knob.

BAND2 LEVEL

USER

] to use the settings made in [

OFF

:Cancels.

OFF

:Cancels.

below.)

OFF

:Cancels.

:Selects your preferred bass boost level.;

: Selects a preset equalizer

MANUAL EQ

Default:

].)

ENGLISH

+ 39 hidden pages