Kenwood KDV-MP3346M, KDV-MP3346 User Manual

Declaration of Conformity with regard to the EMC Directive 2004/108/EC

Manufacturer:

Kenwood Corporation 2967-3 Ishikawa-machi, Hachioji-shi, Tokyo, 192-8525 Japan

EU Representative’s:

Kenwood Electronics Europe BV Amsterdamseweg 37, 1422 AC UITHOORN, The Netherlands

DVD-RECEIVER

KDV-MP3346

For Turkey Bu ürün 26891sayılı Resmi Gazete’de yayımlanan Elektrikli ve Elektronik Eşyalarda Bazı Zararlı Maddelerin

Kullanımının Sınırlandırılmasına Dair Yönetmeliğe uygun olarak üretilmiştir.

This product complies with Directive, Number 26891 regarding “REGULATION ON THE RESTRICTION OF THE USE OF

CERTAIN HAZARDOUS SUBSTANCES IN ELECTRICAL AND ELECTRONIC EQUIPMENT”.

The marking of products using lasers

The label is attached to the chassis/case and says that the component uses laser beams that have been classied as Class 1. It means that the unit is utilizing laser beams that are of a weaker class. There is no danger of hazardous radiation outside the unit.

• Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.

• “DVD Logo” is a trademark of DVD Format/Logo Licensing Corporation registered in the US, Japan and other countries.

• DivX® is a registered trademark of DivX, Inc., and is used under license.

• ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, Inc. This is an ocial DivX Certied device that plays DivX video. Visit www.divx.com for more information and software tools to convert your les into DivX video.

• ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certied® device must be registered in order to play DivX Videoon-Demand (VOD) content. To generate the registration code, locate the DivX VOD section in the device setup menu. Go to vod.divx.com with this code to complete the registration process and learn more about DivX VOD.

• Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.

• This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.

KDV-MP3346M

INSTRUCTION MANUAL

This symbol mark indicates that Kenwood manufactured this product so as to decrease harmful in uence on the environment.

WARNINGS (to prevent injury or fire):

• Never put or leave any metallic objects (such

as coins or metal tools) inside the unit to prevent short circuit.

• DO NOT install any unit or wire any cable in a

location where;

– it may obstruct the steering wheel and

gearshift lever operations.

– it may obstruct the operation of safety

devices such as air bags.

– it may obstruct visibility.

• DO NOT operate the unit while driving.

• If you need to operate the unit while driving,

be sure to look around carefully.

• The driver must not watch the monitor while

driving.

If the parking brake is not engaged, “DRIVER

MUST NOT WATCH THE MONITOR WHILE DRIVING.” appears on the monitor, and no playback picture will be shown.

– This warning appears only when the parking

brake lead is connected to the parking brake system built in the car (refer to the Installation/Connection Manual).

Important to know...

• Lens fogging: When you turn on the car

heater in cold weather, dew or condensation may form on the lens in the DVD player of the unit. This condensation on the lens may not allow discs to play. In such a situation, remove the disc and wait for the condensation to evaporate. If the unit still does not operate normally after a while, consult your Kenwood dealer.

• When you purchase external components,

check with your Kenwood dealer to make sure that they work with your model and in your area.

• Detailed information and notes about the

playable audio files are stated in an online manual on the following site: www.kenwood.com/cs/ce/audiofile/

How to attach/detach the control panel

• The control panel is a precision piece of equipment and can be damaged by shocks or jolts.

• Keep the control panel in its hard case while detached.

• Do not expose the control panel (and the hard case) to direct sunlight or excessive heat or humidity. Also avoid places with too much dust or the possibility of water splashing.

• To prevent deterioration, do not touch the terminals of the unit or control panel with your fingers.

How to reset your unit

If this unit (or the connected external components) fails to operate properly, press the reset button.

The unit returns to factory settings when the reset button is pressed.

2 ENGLISH

How to read this manual

The illustrations of the display and the panel appearing in this manual are examples used to explain more clearly how the controls are used. Therefore, what appears on the display in the illustrations may differ from what appears on the display on the actual equipment, and some of the illustrations on the display may be inapplicable.

The following icons/symbols are used to indicate:

[Hold]

( XX)

<XXXX> Function Control setting item

Press and hold the button(s) until the desired operation begins.

Turn the control knob.

Turn the control knob to make a selection, then press to confirm.

Reference page number

Continued on the next page

CONTENTS

4 Preparation

4 Canceling the display

demonstration

4 Setting the clock 5 Prepare the remote controller

(RC-DV350)

5 Other settings before operations

7 Basic operations

7 Control panel 7 Remote controller (RC-DV350)

9 Listening to the radio 11 Playable disc type 12 Listening to a disc

13 Operation using the control panel 14 Operation using the remote

controller

21 Listening to the other external

components

22 Other adjustments 24 Troubleshooting 26 Maintenance 27 Language codes 28 Specifications

3ENGLISH

Preparation

The display demonstration is always turned on unless you cancel it. When you turn on the power (or after you reset the unit), the display shows:

“CANCEL”

• If no operation is done for about 15 seconds, “DEMO START” appears and the display

demonstration starts.

To cancel the display demonstration:

Press the control knob.

“NO/<YES>” is shown on the display.

Press the control knob again to select

“YES”.

“DEMO OFF” appears on the display.

• If “NO” is selected, “DEMO START”

You can also cancel the display demonstration from the Function Control settings, see the following:



Canceling the display

“DEMO” = “PRESS” =

“VOL KNOB”

appears and the display demonstration starts.

demonstration

Turn on the power.

2 Enter Function Control settings.

4 Finish the procedure.

[Hold]



Setting the clock

Turn on the power.

2 Enter Function Control settings.

3 Turn the control knob to make a

selection, then press to confirm.

1 : 00

4 Adjust the hour.

3 Turn the control knob to make a

selection, then press to confirm.

4 ENGLISH

5 Adjust the minute.

1 : 00



Other settings before

operations

Before using this unit for the first time, make the following settings for optimum performance.

1 Turn the unit to standby state.

Press 4 to return to the hour adjustment.

6 Finish the procedure.

[Hold]

 While in clock display screen, press and hold

SCRL DISP will enter <CLOCK ADJ> setting

directly. Perform steps hour and minute.



Prepare the remote

and 5 to adjust the

controller (RC-DV350)

Insert the batteries into the remote controller by matching the polarity (+ and –) correctly.

AAA/R03

If the range or effectiveness of the remote control decreases, replace both batteries.

Caution:

• Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

• Battery shall not be exposed to excessive heat such as sunshine, fire, or the like.

2 Enter Function Control settings.

3 Select “INIT SETUP.”

4 Turn the control knob to make a

selection, then press to confirm.

See table on page 6 for selection.

5 Finish the procedure.

[Hold]

5ENGLISH

The following settings can only be done when the unit is on standby state.

Item Selectable setting, [ Initial ]

KEY BEEP • ON

• OFF

TDF ALARM

AUX SET

21)

(

SWITCH PRE

SP SELECT —

PAL/NTSC

FILE TYPE

20)

(

• ON

• OFF

• ON

• OFF

• REAR

• SUBW

• PAL

• NTSC

• A + V

• PIC

: Activates the keypress tone. : Deactivates the keypress tone.

: When you turn off the ignition switch of the car, the unit beeps if the

control panel is not detached. Detach the control panel to reduce the possibility of theft.

: Cancels.

: Enables “AUX” in source selection. : Disables “AUX” in source selection.

: Selects if the REAR/SW terminals on the rear of this unit are used for

connecting the speakers (through an external amplifier).

: Selects if the REAR/SW terminals on the rear of this unit are used for

connecting a subwoofer (through an external amplifier).

: Selects the connected speaker size for strong bass and to improved

clarity.

OFF, 5/4, 6 × 9/6, OEM

: Selects this if your monitor is of the PAL color system. : Selects this if your monitor is of the NTSC color system.

: Selects to play only audio and/or video files. : Selects to play JPEG files.

When a call comes in...

“CALL” appears on the display and the audio system is paused.

• When the call ends, “CALL” disappears and the audio system resumes. You can also resume the audio system by pressing

SRC

during a conversation.

 Make sure the MUTE lead is connected to a mobile phone system in your car.

Installation/Connection Manual).

(

6 ENGLISH

Basic operations



Control panel

Detaches the control panel

Loading slot

Remote sensor

• DO NOT expose to bright sunlight.

Control knob



Remote controller (RC-DV350)

Display window Auxiliary input jack

When using the remote controller, point the top of the remote control towards the remote sensor as directly as possible.

The operations from the remote controller differ depending on the position of the mode switch.

AUD (audio) mode:

For controlling a selected source or tuner source, etc.

DVD mode:

For controlling playback of a DVD with the player integrated in this unit.

 You cannot operate the remote controller if the

mode switch is in the middle.

2 ZONE

R. VOL (∧/∨)

for this unit.

/ are not applicable

7ENGLISH

When you press or hold the following button(s)...

Main unit

Remote

controller

—

• Turns on.

• Turns off if pressed and held.

Selects the available sources (if the power is turned on).

• If the source is ready, playback also starts.

Adjusts the volume level.

• Selects items if turn the control knob on the main unit.

General operation

—

— Ejects the disc.

—

Selects items of the on-screen bar. ( 18)

• Confirms selection.

• Enters Function Control settings if pressed the control knob on the main unit.

 If no operation is done for about one minute after pressing

the control knob, the operation will be canceled (except if you have selected “AUD CTRL” or “AUD SETUP”). (

Enters Music/Video Search mode. (

Returns to the previous menu.

• Selects the FM bands (F1 / F2 / F3) or AM (in AUD mode if using the remote controller).

• Selects the next/previous folder of an DivX/MP3/WMA/ WAV disc. (Pressing the next folders.)

• Changes the display information.

• Scrolls the display information if pressed and held.

• Enters clock adjustment mode directly if pressed and held while in clock display screen. ( 4, 5)

Attenuates the sound (if the power is on). “ATT” indicator flashes.

• To return to the previous level, press the button again. “ATT” indicator goes off.

BAND

on the main unit can only select

13)

22)

8 ENGLISH

Listening to the radio

]

“TUNER”

]

“F1,” “F2,” “F3,” or “AM”

You can select or set the <TUNER CTRL> settings while listening to the radio.

1 Enter Function Control settings.

“ST” lights up when receiving an FM

stereo broadcast with sufficient signal strength.

3 Turn the control knob to make a

selection, then press to confirm.

See table below for selection.

2 Select “TUNER CTRL.”

4 Finish the procedure.

[Hold]

Item Selectable setting, [ Initial ]

SEEK MODE

Tuning mode

A-MEMORY

Automatic presetting

CRSC SET * Clear Reception Stereo Control setting

All previously stored stations are erased and stations are stored anew. The station stored in the lowest

preset number will be automatically tuned in.

Displayed only when the source is “TUNER (F1 / F2 / F3).”

Strong electrical fields (such as from power lines) may cause unstable sound quality when <CRSC SET> is

set to <ON>. In such situation, set to <OFF>.

Selects the tuning mode for 4 / ¢ buttons.

• AUTO1

• AUTO2

• MANU

You can preset up to 6 stations for each FM and AM band.

• START *

• CANCEL

• ON *

• OFF

: Automatically search for a station. : Search in order of the stations in the preset memory. : Manually search for station.

: Automatically search for stations and stored in to the memory.

“A-MEMORY” flashes on the display during search.

: Returns to item selection menu.

: Improve the FM reception, (but the stereo effect may be lost). : Cancels. The stereo effect may be restored automatically

(depending on the reception condition).

9ENGLISH

+ 20 hidden pages