Kenwood KDC-BT768HD, KMC-D768BT, KDC-X701, KDC-X501, KDC-BT568U User Manual

0 (0)

KDC-X701

KDC-X501

KDC-BT768HD

KDC-BT568U

KMR-D768BT

CD-RECEIVER

INSTRUCTION MANUAL

AMPLI-TUNER LECTEUR DE CD

MODE D’EMPLOI

REPRODUCTOR DE DISCOS COMPACTOS RECEPTOR DE FM/AM

MANUAL DE INSTRUCCIONES

For your records

Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below. Refer to the model and serial numbers whenever you call upon your Kenwood dealer for information or service on the product. Model KDC-X701/KDC-BT768HD/KMR-D768BT/KDC-X501/KDC-BT568U Serial number

US Residents Only

CAUTION

Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. In compliance with Federal Regulations, following are reproductions of labels on, or inside the product relating to laser product safety.

JVC KENWOOD Corporation 2967-3, ISHIKAWA-MACHI, HACHIOJI-SHI, TOKYO, JAPAN

THIS PRODUCT COMPLIES WITH DHHS RULES 21CFR SUBCHAPTER J IN EFFECT AT DATE OF MANUFACTURE.

Location : Top Plate

FCC WARNING

This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.

FCC NOTE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment may cause harmful interference to radio communications, if it is not installed and used in accordance with the instructions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Información acerca de la eliminación de equipos eléctricos y electrónicos al final de la vida útil (aplicable a los países que hayan adoptado sistemas independientes de recogida de residuos)

Los productos con el símbolo de un contenedor con ruedas tachado no podrán ser desechados como residuos domésticos. Los equipos eléctricos y electrónicos al final de la vida útil, deberán ser reciclados en instalaciones que puedan dar el tratamiento adecuado a estos productos y a sus subproductos residuales correspondientes. Póngase en contacto con su administración local para obtener información sobre el punto de recogida más cercano. Un tratamiento correcto del reciclaje y la eliminación de residuos ayuda a conservar los recursos y evita al mismo tiempo efectos perjudiciales en la salud y el medio ambiente.

Informação sobre a eliminação de pilhas

Este produto não deve ser eliminado como lixo doméstico geral. Devolva a pilha usada ao revendedor ou entidade autorizada para que a mesma seja devolvida ao fabricante ou importador. A reciclagem e a eliminação de lixo de maneira apropriada ajudarão a conservar os recursos naturais ao mesmo tempo que prevenirão os efeitos prejudicais à nossa saúde e ao meio ambiente.

CALIFORNIA, USA ONLY

This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material—special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate

IC (Industry Canada) Notice

This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired

operation of the device.

Note de IC (Industrie Canada)

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage; (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage

est susceptible d’en compromettre le fonctionnement.

CAUTION

This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that is deemed to comply without maximum permissive exposure evaluation (MPE). But it is desirable that it should be installed and operated keeping the radiator at least 20cm or more away from person’s body.

ATTENTION

Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un environnement non contrôlé et respecte les règles les radioélectriques (RF) de la FCC lignes directrices d’exposition et d’exposition aux fréquences radioélectriques (RF) CNR-102 de l’IC. Cet équipement émet une énergie RF très faible qui est considérée comme conforme sans évaluation de l’exposition maximale autorisée (MPE). Cependant, il est souhaitable qu’il devrait être installé et utilisé en gardant une distance de 20 cm ou plus entre le radiateur et le corps humain.

Contains Bluetooth Module FCC ID: ZWY8350X IC ID: 12033A-8350X

This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.

Para cumplimiento de la IFT:

“La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su

operación no deseada”

SOFTWARE LICENSE AGREEMENT

The software embedded in the Product (hereinafter the "Licensed Software") provided by Licensor is copyrighted to or sublicensable by the Licensor, and this Agreement provides for the terms and conditions which Users shall follow in order to use the Licensed Software.

The User shall use the Licensed Software by agreeing with the terms of this Software License Agreement. This Agreement shall be deemed completed at the time the User (hereinafter the "User") initially used the Product in which the "Licensed Software" is embedded.

The Licensed Software may include the software which has been licensed to the Licensor directly or indirectly from any third party. In such case, some third parties require the Users to follow their conditions for use separately from this Software License Agreement. Such software shall not be subject to this Agreement, and the Users are urged to read the "Important Notice concerning the Software" to be provided separately below.

Article 1 General Provision

The Licensor shall grant to the User a non-exclusive and non-transferable (other than the exceptional case referred to in Article 3, Paragraph 1) licensed to use the Licensed Software within the country of the User. (the country where the User bought the Product(hereinafter the "Country")

Article 2 License

1. The license granted under this Agreement shall be the right to use the Licensed Software in the Product.

2. The User shall not duplicate, copy, modify, add, translate or otherwise alter, or lease the Licensed Software and any related documents, whether in whole or in part.

3. The use of the Licensed Software shall be limited to personal purpose, and the Licensed Software shall not be distributed, licensed or sub-licensed whether it is for commercial purpose or not.

4. The User shall use the Licensed Software according to the directions described in the operation manual or help file, and is prohibited to use or duplicate any data in a manner violating the Copyright Law or any other laws and regulations by applying whole or a part of the Licensed Software.

Article 3 Conditions for Grant of License

1. When the User transfers the Product, it may also transfer the license to use the Licensed Software embedded in the Product (including any related materials, updates and upgrades) on condition that no original, copies or related materials continue in the possession of the User, and that the User shall cause the transferee to comply with this Software License Agreement.

2. The User shall not carry out reverse engineering, disassembling, decompiling or any other code analysis works in connection with the Licensed Software.

Article 4 Right pertaining to the Licensed Software

Any and all copyrights and other rights pertaining to the Licensed Software and related documents shall belong to the Licensor or the original holder of the right who granted to the Licensor the license or sublicense for the Licensed Software (hereinafter the "Original Rightholder"), and the User shall not be entitled to any right other than the license granted hereunder, in respect of the Licensed Software and any related documents.

Article 5 Indemnification of Licensor

1. Neither the Licensor nor the Original Rightholder shall be liable for any damage incurred by the User or any third party due to the exercise of the license granted to the User under this Agreement, unless otherwise restricted by law.

2. The Licensor will offer no guarantee for the merchantability, convertibility and consistency with certain objective of the Licensed Software.

Article 6 Liability to Third Party

If any dispute has arisen with any third party due to an infringement upon a copyright, patent or any other intellectual property right that was caused by the User's use of the Licensed Software, the User shall settle such dispute at its own cost and hold the Licensor and the Original Rightholder harmless from any inconvenience it may cause.

Article 7 Confidentiality

The User shall keep the confidentiality of such portion of the Licensed Software, related documents thereof or any other information to be granted under this Agreement, as well as the conditions of this Agreement as has not yet entered the public domain, and shall not disclose or divulge the same to any third party without approval of the Licensor.

iii

Article 8 Termination

In case the User falls under any of the events described in the following items, the Licensor may immediately terminate this Agreement or claim that the User compensates for the damage incurred by the Licensor due to such event: (1) when the User violated any provision of this Agreement; or (2) when a petition has been filed against the User for an attachment, provisional attachment, provisional disposition or any other compulsory execution.

Article 9 Destruction of the Licensed Software

If this Agreement is terminated pursuant to the provision of Article 8, the User shall destroy the Licensed Software, any related documents and copies thereof within two (2) weeks from such date of termination.

Article 10 Protection of Copyright

1. The copyright and all the other intellectual property rights relating to the Licensed Software shall belong to the Licensor and the Original Rightholder, and in no event shall they be under the ownership of the User.

2. The User shall, whenever it uses the Licensed Software, comply with any laws relating to the copyright and other intellectual property rights.

Article 11 Export Restriction

1. It is prohibited to export the Licensed Software and any related documents outside the country of the User (including transmission thereof outside the country of the User via Internet of other communication tools).

2. The User shall understand that the Licensed Software shall be subject to the export restrictions adopted by the country of User and any other countries.

3. The User shall agree that the software will be subject to any and all applicable international and domestic laws (including the export control regulation of the country of User and any other countries, and any restrictions concerning the end-users, the use by end-users and importing countries to be provided by the country of User and any other countries, and any other governmental authorities).

Article 12 Miscellaneous

1. In the event any part of this Agreement is invalidated by operation of law, the residual provisions shall continue in force.

2. Matters not stipulated in this Agreement or any ambiguity or question raised in the construction of this Agreement shall be provided or settled upon good-faith consultation between the Licensor and the User.

3. The Licensor and the User hereby agree that this Agreement is governed by the laws of Japan, and any dispute arising from, and relating to the rights and obligations under, this Agreement shall be submitted to the exclusive jurisdiction of the Tokyo District Court for its first instance.

Important Notice concerning the Software

-jansson

Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the "Software"), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:

The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.

THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.

CONTENTS

BEFORE USE 2

BASICS 3

GETTING STARTED 4

1 Select the display language

and cancel the demonstration 2 Set the clock and date 3 Set the initial settings

HD RadioTM tuner

(for / )

RADIO

(for /

/ )

CD/USB/iPod/ANDROID 9

AUX 11

Pandora® 12

iHeartRadio® 13

SiriusXM® Radio 14

BLUETOOTH® 17

AUDIO SETTINGS 24

DISPLAY SETTINGS 27

TROUBLESHOOTING 28

REFERENCES 31

Maintenance More information

SPECIFICATIONS 34

INSTALLATION/ CONNECTION 36

BEFORE USE

IMPORTANT

•

To ensure proper use, please read through this manual before using this product. It is especially important that you read and observe

Warning and Caution in this manual.

•

Please keep the manual in a safe and accessible place for future reference.

WARNING

• Do not operate any function that takes your attention away from safe driving.

• Do not ingest the battery, Chemical Burn Hazard

The remote control supplied with this product contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.

Caution

Volume setting:

•

Adjust the volume so that you can hear sounds outside the car to prevent accidents.

•

Lower the volume before playing digital sources to avoid damaging the speakers by the sudden increase of the output level.

General:

•

Avoid using the external device if it might hinder safe driving.

•

Make sure all important data has been backed up. We shall bear no responsibility for any loss of recorded data.

•

Never put or leave any metallic objects (such as coins or metal tools) inside the unit to prevent a short circuit.

•

If a disc error occurs due to condensation on the laser lens, eject the disc and wait for the moisture to evaporate.

•

USB rating for the USB cables from the rear of the unit is indicated on a label.

•

Depending on the types of cars, the antenna will automatically extend when you turn on the unit with the antenna control wire

connected

( 37)

Remote control (RC-406):

•

Do not leave the remote control in hot places such as on the dashboard.

•

The Lithium battery is in danger of explosion if replaced incorrectly. Replace it only with the same or equivalent type.

•

The battery pack or batteries shall not be exposed to excessive heat such as sunshine, fire or the like.

. Turn off the unit or change the source to STANDBY when parking at a low ceiling area.

How to read this manual

•

Operations are explained mainly using buttons on the faceplate of .

•

English indications are used for the purpose of explanation. You can select the display language from the

• [XX]

indicates the selected items.

• ( XX)

indicates references are available on the stated page.

( 37)

[FUNCTION]

menu.

( 5)

ENGLISH

BASICS

Faceplate

Volume

knob

Display window

Lights up when Bluetooth connection is established.

Remote control (RC-406)

(supplied for / )

( 17)

Remote sensor (Do not expose to bright sunlight.)

Detach

button

USB 1 cable from the rear of the unit.

Auxiliary cable from the rear of the unit.

To On the faceplate On the remote control

Turn on the power

Adjust the volume Turn the volume knob. Press

Select a source

Change the display information Press DISP repeatedly.

For : The power will automatically turn off after 20minutes when in standby mode (Auto Power Off).

(For USB 2 cable from the rear of the unit.

Press

• Press and hold to turn off the power.

Press

/ )

repeatedly.

Flashes when the unit enters searching status.

How to resetAttach Detach

( 33)

controlled with an optionally purchased remote control.

How to replace the battery

Press and hold SRC to turn off the power. ( Pressing SRC does not turn on the power. )

• Press and hold volume to 15.

Press ATT during playback to attenuate the sound.

• Press again to cancel.

Press SRC repeatedly.

( Not available )

/ : Can be remotely

: Remote control functions are not available.

or .

Pull out the insulation sheet when using for the first time.

to continuously increase the

ENGLISH

GETTING STARTED

Select the display language and cancel the demonstration

When you turn on the power for the first time (or

[YES], 5

), the display shows: “SEL LANGUAGE” “PRESS” “VOLUME

KNOB”

1 Turn the volume knob to select

then press the knob.

[ENG]

is selected for the initial setup. (For Then, the display shows: “CANCEL DEMO”

KNOB”.

/ / / )

[ENG]

2 Press the volume knob.

[YES]

is selected for the initial setup.

3 Press the volume knob again.

“DEMO OFF” appears.

Set the clock and date

Press the volume knob to enter

2 Turn the volume knob to select

To adjust the clock

3 Turn the volume knob to select

[FUNCTION] [CLOCK]

[CLOCK ADJUST]

4 Turn the volume knob to make the settings, then press the knob.

Hour

5 Turn the volume knob to select 6 Turn the volume knob to select

Minute

[CLOCK FORMAT] [12H]

[FACTORY RESET]

(English) or

, then press the knob.

[SPA]

(Spanish),

“PRESS” “VOLUME

, then press the knob.

[24H]

, then press the knob.

is set to

To set the date

7 Turn the volume knob to select 8 Turn the volume knob to select

the knob.

9 Turn the volume knob to select

[DATE FORMAT] [DD/MM/YY]

[DATE SET]

, then press the knob.

[MM/DD/YY]

, then press

10 Turn the volume knob to make the settings, then press the knob.

Day

Month Year or Month Day Year

11 Press and hold to exit.

To return to the previous setting item, press .

Set the initial settings

Press repeatedly to enter STANDBY.

2 Press the volume knob to enter

[FUNCTION]

3 Turn the volume knob to select an item (see the following table),

then press the knob.

4 Repeat step 3 until the desired item is selected or activated. 5 Press and hold to exit.

To return to the previous setting item, press .

Default:

DISPLAY

EASY MENU

TUNER SETTING

PRESET TYPE

When entering

ON OFF

•

ZONE 2 illumination changes to white color when you enter

[FUNCTION]

•

Refer to the illustration on page 27 for ZONE identification.

NORMAL

(FM1/FM2/FM3/AM).; for each preset button, regardless of the selected band or SiriusXM channel.

[FUNCTION]

:ZONE 1 illumination changes to white color.;

:ZONE 1 illumination remains as

, irregardless of the

:Memorizes one station for each preset button in each band

...

[COLOR SELECT]

[EASY MENU]

MIX

:Memorizes one station or SiriusXM channel

setting.

color.

( 28)

ENGLISH

GETTING STARTED

SYSTEM

KEY BEEP

SOURCE SELECT

PANDORA SRC

IHEART SRC

BUILT-IN AUX

CD READ

F/W UPDATE

UPDATE SYSTEM/UPDATE HD

F/W UPDATE xxxx/ F/W UPDATE Vxx

FACTORY RESET YES

CLOCK

CLOCK DISPLAY

ENGLISH

ESPANOL

:Activates the keypress tone.;

:Enables PANDORA 1/PANDORA 2/PANDORA in source selection.;

OFF

:Disables.

:Enables IHEARTRADIO 1/IHEARTRADIO 2/IHEARTRADIO in source

selection.;

:Enables AUX in source selection.;

: Automatically distinguishes between audio file disc and music CD. ;

: Forces to play as a music CD. No sound can be heard if an audio file disc

is played.

YES

:Starts upgrading the firmware.; NO:Cancels (upgrading is not activated). For details on how to update the firmware, visit <www.kenwood.com/cs/ce/>.

:Resets the settings to default (except the stored station).;

:Cancels.

(For / / /

:The clock time is shown on the display even when the unit is turned

off.;

Select the display language for if applicable. By default,

OFF

( 12)

OFF

:Disables.

( 13)

(for / )

)

OFF

:Cancels.

[FUNCTION]

[ENGLISH]

is selected.

:Deactivates.

OFF

:Disables.

( 11)

menu and music information

Applicable only when you connect Kenwood Marine Remote Control unit (KCA-RC55MR, optional accessory) to this unit.

• For connection,

• Refer also to the supplied instruction manual of the Kenwood Marine Remote Control unit for more information.

Preparation:

Press to enter

[FUNCTION].

37, Wiring connection

repeatedly to enter STANDBY, then press the volume knob

(for )

1 Turn the volume knob to select an item, then press the knob.

[SYSTEM]



Remote control ID list is displayed.

•

[REMOTE SETTING]

[YES]

indicates that this ID is already registered.

[NO]

indicates that this ID is available.

2 Turn the volume knob to select an available ID

[REMOTE ID2]/[REMOTE ID3]

“REGISTERING” appears on the display window.

To register, on the Kenwood Marine Remote Control unit:

• Press ENTER to register as

• Press SRC to register as

• Press DISP to register as

Once the ID is registered, “COMPLETED” appears.

To delete the registered ID



[REMOTE ID SET]

, then press the knob

[REMOTE ID1]

[REMOTE ID2]

[REMOTE ID3]

[REMOTE ID1]

1 Turn the volume knob to select an item, then press the knob.

[SYSTEM]



2 Turn the volume knob to select the ID to delete [

[REMOTE SETTING]

[

ID2 DELETE]/[ID3 DELETE]

3 Turn the volume knob to select

select

[NO]

to cancel.

• To exit, press and hold

• To return to the previous setting item, press



[REMOTE ID DELETE]

, then press the knob.

[YES]

to delete the selected ID, and

ID1 DELETE]

ENGLISH

HD Radio™ tuner

You can tune in to both conventional and HD Radio broadcasts.

• To find HD Radio stations in your area, visit <http://www.hdradio.com>.

(for / )

Search for a station

Press repeatedly to select HD RADIO.

2 Press repeatedly (or press / on the remote

control) to select FM1/FM2/FM3/AM.

3 Press S/T (or press S/ on the remote control) to

search for a station or channel.

• To change the searching method for S/T: Press repeatedly.

AUTO1 : Automatically search for a station or channel. AUTO2 : Search for a preset station or channel. MANUAL : Manually search for a station or channel.

• To store a station or channel: Press and hold one of the number buttons (1to6).

• To select a stored station or channel: Press one of the number buttons (1to6) (or press one of the number buttons (1to6) on the remote control).

Direct Access Tuning

(using the remote control)

1 Press DIRECT to enter Direct Access Tuning. 2 Press the number buttons to enter a frequency. 3 Press to search for a station or channel.

• To cancel, press or DIRECT.

• If no operation is done for 10seconds after step is automatically canceled.

ENGLISH

2, Direct Access Tuning

Select an HD Radio multicast channel

Many HD Radio stations offer more than one channel programming. This service is called multicasting. While receiving HD Radio multicast

channels....

Press S/T to select your desired channel (HD1 to HD8).

“LINKING” appears while linking to a multicast channel.

Receive an Emergency Alert message

You can receive an emergency alert message while listening to another source or while in STANDBY, via HD Radio Broadcast.

Activate emergency alert message reception

Press the volume knob to enter

1 2 Turn the volume knob to select 3

Turn the volume knob to select

4 Turn the volume knob to select

[FUNCTION] [TUNER SETTING]

[EMERGENCY ALERT], then press the knob.

[ON]

, then press the knob.

5 Press and hold to exit.

• To deactivate emergency alert message reception, select

• To return to the previous setting item, press

[OFF]

in step 4.

Receive an emergency alert message

When an emergency alert message is received, it appears and remains on the display until the user performs the “Ignore” function.

• Press message. The same emergency alert message will not interrupt again for 12 hours.

(or press SRC on the remote control) to ignore the alert

Display received emergency alert messages

The received emergency alert messages are stored in the Alert Message List, and you can check them later. While listening to the HD RADIO source...

1 Press to display the Alert Message List. 2 Turn the volume knob to select a message.

HD Radio™ tuner

(for / )

3 Press the volume knob to display the information related to the message. 4 Press again to exit.

• “NO LIST” appears when the list is empty.

• This feature can store up to four messages in the list.

• To clear the message list, set

[FACTORY RESET]

[YES]. ( 5)

RADIO

(for / / )

Other settings

Press the volume knob to enter

[FUNCTION]

2 Turn the volume knob to select an item (see the following table), then press

the knob.

3 Repeat step 2 until the desired item is selected or activated. 4 Press and hold to exit.

To return to the previous setting item, press .

Default:

TUNER SETTING

IF BAND

AUTO MEMORY YES

RECEIVE MODE

CLOCK

TIME SYNC

AUTO

:Increases the tuner selectivity to reduce interference noises from adjacent FM stations. (Stereo effect may be lost.); adjacent FM stations, but sound quality will not be degraded and the stereo effect will remain.

:Automatically starts memorizing 6 stations with good reception.; NO:Cancels.

•

Selectable only if

Sets the receive mode of the HD Radio receiver.

AUTO

:Automatically tunes to analog broadcast when there is no digital broadcast.;

DIGITAL

only.

:Synchronizes the unit’s time to the Radio Broadcast Data System station time.;

OFF

:Cancels.

[NORMAL]

:Tunes in to digital broadcast only.;

WIDE

is selected for

:Subjects to interference noises from

[PRESET TYPE]. ( 4)

ANALOG

:Tunes in to analog broadcast

Search for a station

Press repeatedly to select TUNER.

2 Press repeatedly (or press / on

the remote control) to select FM1/FM2/FM3/AM.

3 Press S/T (or press S/ on the remote

control) to search for a station.

• To change the searching method for S/T: Press

AUTO1 : Automatically search for a station. AUTO2 : Search for a preset station. MANUAL : Manually search for a station.

• To store a station: Press and hold one of the number buttons (1to6).

• To select a stored station: Press one of the number buttons (1to6) (or press one of the number buttons (1to6) on the remote control).

Direct Access Tuning

repeatedly.

(using the remote control)

1 Press DIRECT to enter Direct Access Tuning. 2 Press the number buttons to enter a frequency. 3 Press to search for a station.

• To cancel, press or DIRECT.

• If no operation is done for 10seconds after step Access Tuning is automatically canceled.

ENGLISH

2, Direct

RADIO

(for / / )

Other settings

Press the volume knob to enter

Turn the volume knob to select an item (see the following table), then press the knob.

[FUNCTION]

3 Repeat step 2 until the desired item is selected or activated. 4 Press and hold to exit.

To return to the previous setting item, press .

TUNER SETTING

AUTO MEMORY

MONO SET

TI ON

PTY SEARCH

CLOCK

TIME SYNC

YES

:Automatically starts memorizing 6 stations with good reception.;

:Cancels.

•

Selectable only if

:Improves the FM reception, but the stereo effect may be lost.;

OFF

:Cancels.

:Allows the unit to temporarily switch to Traffic Information if available

(“TI” lights up).;

Select the available Program Type (see the following), then press

/T to start.

:Synchronizes the unit’s time to the Radio Broadcast Data System station

time.;

OFF

:Cancels.

[NORMAL]

OFF

:Cancels.

is selected for

[PRESET TYPE]. ( 4)

Default:

Available Program Type for

SPEECH : NEWS, INFORM

(religious talk), (spanish talk),

MUSIC

ROCK, CLS ROCK

(softrock),

JAZZ, CLASSICL

•

• If the volume is adjusted during reception of traffic information, the

(soft rhythm and blues), (spanish music),

The unit will search for the Program Type categorized under [SPEECH]

[MUSIC]

if selected.

[MONO SET]/[TI]/[PTY SEARCH]

FM1/FM2/FM3.

adjusted volume is memorized automatically. It will be applied the next time traffic information is turned on.

TOP 40, COUNTRY, OLDIES, SOFT, NOSTALGA

[PTY SEARCH]

(information),

PERSNLTY

WEATHER

(classic rock),

(classical),

HIP HOP

SPORTS, TALK, LANGUAGE, REL TALK

(personality),

ADLT HIT

R & B

(rhythm and blues),

REL MUSC

is selectable only when the band is

PUBLIC, COLLEGE, HABL ESP

(adult hits),

(religious music),

SOFT RCK

(nostalgia),

SOFT R&B

MUSC ESP

ENGLISH

CD/USB/iPod/ANDROID

Start playback

The source changes automatically and playback starts.

USB 1 cable from the rear of the unit (USB input terminal).

You can also connect to the USB 2 cable from the rear of the unit (USB input terminal).

KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type

Do not leave the cable inside the car when not using.

Label side

USB

CA-U1EX (max.: 500mA) (optional accessory)

iPod/iPhone

KCA-iP102/KCA-iP103 (optional

accessory) iPod/iPhone

ANDROID

Micro USB 2.0 cable (commercially available)

Eject disc

or accessory of the

Selectable source:

•

/ : CD/USB 1/USB 2/iPod 1/iPod 2/ANDROID 1/ANDROID 2

/ / : CD/USB/iPod USB/ANDROID

To On the faceplate On the remote control

Playback/pause Press .

Reverse/Fast-forward

Select a track/file

Select a folder

Repeat play

Press and hold S/T. Press and hold S/ .

Press S/T. Press S/

Press J/K.

Press repeatedly.

TRACK REPEAT/ALL REPEAT FILE REPEAT/FOLDER REPEAT/ALL REPEAT

Press

/ .

: Audio CD

: MP3/WMA/AAC/WAV/

FLAC file

Random play

FILE REPEAT/FOLDER REPEAT/REPEAT OFF

Press repeatedly.

DISC RANDOM/RANDOM OFF

: Audio CD

FOLDER RANDOM/RANDOM OFF

: iPod or ANDROID

: MP3/WMA/AAC/WAV/FLAC file,

iPod or ANDROID

Press and hold

When connecting an Android device, “Press [VIEW] to install KENWOOD MUSIC PLAY APP” is shown. Follow the

to select

ALL RANDOM

instructions to install the application. You can also install the latest version of KENWOOD MUSIC PLAY application on your Android device before connecting. For more information, visit <www.kenwood.com/cs/ce/>.

For ANDROID: Applicable only when

For CD: Only for MP3/WMA/AAC files. This does not work for iPod/ANDROID.

For iPod/ANDROID: Applicable only when

For CD: Only for MP3/WMA/AAC files.

[BROWSE MODE]

is selected.

[MODE OFF]/[BROWSE MODE]

( 10)

is selected.

( 10)

ENGLISH

CD/USB/iPod/ANDROID

Select control mode

While in iPod 1/iPod 2/iPodUSB source, press 5 repeatedly.

MODE ON

: Control iPod using the iPod itself. However, you can still play/

MODE OFF

While in ANDROID 1/ANDROID 2/ANDROID source, press 5 repeatedly.

BROWSE MODE

HAND MODE

While in USB 1/USB 2/USB source, press 5 repeatedly.

Stored songs in the following drive will be played back.

• Selected internal or external memory of a smartphone (Mass Storage

• Selected drive of a multiple drives device.

While listening to TuneIn Radio, TuneIn Radio Pro or Aupeo, connect the iPod/iPhone to the USB input terminal of the unit.

• The unit will output the sound from these applications.

For iPod/ANDROID, applicable only when selected.

1 Press . 2 Turn the volume knob to select a folder/list, then press the knob.

pause, file skip, fast-forward or reverse from this unit.

: Control iPod from this unit.

: Control Android device from this unit via KENWOOD

MUSIC PLAY application installed in the Android device.

: Control Android device using the Android device itself via

other media player applications installed in the Android device. However, you can still play/pause and file skip from this unit.

Select music drive

Class).

Listen to TuneIn Radio/TuneIn Radio Pro/Aupeo

Select a file from a folder/list

[MODE OFF]/[BROWSE MODE]

ENGLISH

3 Turn the volume knob to select a file, then press the knob.

Quick Search

ANDROID 2 and ANDROID source)

If you have many files, you can search through them quickly.

Turn the volume knob quickly to browse through the list quickly.

Skip Search

ANDROID 2 and ANDROID source)

Press S/T to search at a preset skip search ratio.

[SKIP SEARCH])

• Pressing and holding S/T searches at a 10% ratio.

Alphabet search

ANDROID 1, ANDROID 2 and ANDROID source)

You can search for a file according to the first character.

For iPod 1/iPod 2/iPod USB source

(applicable only for CD, USB 1, USB 2, USB, ANDROID 1,

(applicable only for iPod 1, iPod 2, iPod USB, ANDROID 1,

( 11,

(applicable only for iPod 1, iPod 2, iPod USB,

1 Turn the volume knob quickly to enter character search. 2 Turn the volume knob to select the character.

• Select “ 3 Press S/T to move to the entry position.

” to search for a character other than AtoZ, 0to9.

• You can enter up to 3characters. 4 Press the volume knob to start searching.

For ANDROID 1/ANDROID 2/ANDROID source

1 Press J/K to enter character search. 2 Turn the volume knob to select the character.

^A^: Upper case letters (A to Z) _A_: Lower case letters (a to z)

-0-: Numbers (0 to 9) : Character other than AtoZ, 0to9

***

3 Press the volume knob to start searching.

• To return to the root folder/first file/top menu, press 5.

BT AUDIO source.)

• To return to the previous setting item, press .

• To cancel, press and hold

(Not applicable for

CD/USB/iPod/ANDROID

Direct Music Search

1 Press DIRECT. 2 Press the number buttons to enter a track/file number. 3 Press to search for music.

• To cancel, press or DIRECT.

• Not available if Random Play is selected.

• Not applicable for iPod 1, iPod 2, iPodUSB, ANDROID 1, ANDROID 2 and ANDROID source.

Settings to use KENWOOD Remote application

KENWOOD Remote application is designed to control the KENWOOD car receiver’s operations from the iPhone/iPod (via USB input terminal).

Preparation:

Install the latest version of KENWOOD Remote application on your device before connecting. For more information, visit <www.kenwood.com/cs/ce/>.

You can make the settings in the same way as connection via Bluetooth.

(using the remote control)

( 23)

AUX

Preparation:

Select

[ON]

for

[BUILT-IN AUX]

Start listening

Connect a portable audio player (commercially available).

Auxiliary cable from the rear of the unit

2 Press repeatedly to select AUX. 3 Turn on the portable audio player and start playback.

for

[SOURCE SELECT]. ( 5)

3.5mm (1/8") stereo mini plug with “L” shaped connector (commercially available)

Portable audio player

Other settings

Press the volume knob to enter

Turn the volume knob to select an item (see the following table), then press the knob.

[FUNCTION]

3 Repeat step 2 until the desired item is selected or activated. 4 Press and hold to exit.

To return to the previous setting item, press .

Default:

USB

MUSIC DRIVE DRIVE CHANGE

playback starts. Repeat steps

SKIP SEARCH 0.5%/1%/5%/10%

ANDROID source, selects the skip search ratio over the total files.

:The next drive (

to 3 to select the following drives.

[DRIVE 1]

[DRIVE 4]

) is selected automatically and

: While listening to iPod 1, iPod 2, iPodUSB, ANDROID 1, ANDROID 2 or

Set the AUX name

While listening to a portable audio player connected to the unit...

1 Press the volume knob to enter 2 Turn the volume knob to select

the knob.

3 Turn the volume knob to select

press the knob.

[FUNCTION] [SYSTEM]

, then press

[AUX NAME SET]

4 Turn the volume knob to select an item, then press

the knob.

AUX

(default)/

DVD/PORTABLE/GAME/VIDEO/TV

5 Press and hold to exit.

To return to the previous setting item, press .

ENGLISH

, then

Pandora®

Preparation:

Install the latest version of the Pandora application on your device (iPhone/ iPod touch), then create an account and log in to Pandora.

• Select

[ON]

for

[PANDORA SRC]

Start listening

Open the Pandora application on your device.

2 Connect your device to the USB input terminal.

3 Press repeatedly to select PANDORA 1/PANDORA 2/PANDORA.

Broadcast starts automatically.

To On the faceplate On the remote control

Playback/pause

Skip a track

Thumbs up or thumbs down

KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type

Do not leave the cable inside the car when not using.

If thumbs down is selected, the current track is skipped.

[SOURCE SELECT]. ( 5)

USB 1 cable from the rear of the unit.

connect to the USB 2 cable from the rear of the unit.

Press

Press T.

Press J/K.

KCA-iP102/KCA-iP103 (optional accessory) accessory of the iPod/iPhone

/ : You can also

. Press

Press

/ .

Create and save a new station

Press .

2 Turn the volume knob to select

the knob.

3 Turn the volume knob to select

[FROM TRACK]

A new station is created based on the artist or current song.

, then press the knob.

[NEW STATION]

[FROM ARTIST]

, then press

4 Press and hold one of the number buttons (1to5) to store.

To select a stored station: Press one of the number buttons (1to5).

Search for a registered station

Press .

2 Turn the volume knob to select an item, then press the

knob.

[SORT BY DATE] [SORT BY A-Z]

: According to the registered date

: By alphabetical order

3 Turn the volume knob (or press J / K on the remote

control) to select the desired station.

4 Press the volume knob (or press on the remote

control) to confirm.

To cancel, press and hold

Bookmark current song information

Press and hold the volume knob.

“BOOKMARKED” appears and the information is stored to your device.

• The bookmark is available on your Pandora account but not on this unit.

ENGLISH

Pandora® iHeartRadio®

Delete a station

While listening to PANDORA...

1 Press . 2 Turn the volume knob to select

[STATION DELETE]

3 Turn the volume knob to select

[SORT BY A-Z]

, then press the knob.

[SORT BY DATE]

, then press the knob.

4 Turn the volume knob to select the desired

station to delete, then press the knob.

5 Turn the volume knob to select

press the knob.

[YES]

, then

6 Press and hold to exit.

To return to the previous setting item, press .

Preparation:

Install the latest version of iHeartAuto application on your device (iPhone/iPod touch), then create an account and log in to iHeartRadio.

• Select

[ON]

for

[IHEART SRC]

Start listening

Open the iHeartAuto application on your device.

2 Connect your device to the USB input terminal.

[SOURCE SELECT]. ( 5)

USB 1 cable from the rear of the unit.

KCA-iP102/KCA-iP103 (optional

accessory) iPod/iPhone

or accessory of the

connect to the USB 2 cable from the rear of the unit.

/ : You can also

3 Press repeatedly to select IHEARTRADIO 1/IHEARTRADIO 2/IHEARTRADIO.

Broadcast starts automatically.

To On the faceplate On the remote control

Playback/pause

Skip a track for custom station

Thumbs up or thumbs down

Create a new/custom station Press 1. ( Not available )

Scan for live station

KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type

Do not leave the cable inside the car when not using.

Press

Press T.

Press J/K.

1 2

. Press

Press 2 to start scanning. Press 2 again to listen to the station.

Press

( Not available )

ENGLISH

iHeartRadio®

Search and store a station

Press .

2 Turn the volume knob to select a category, then

press the knob.

3 Turn the volume knob (or press J / K on the remote

control) to select the desired station.

4 Press the volume knob (or press on the

remote control) to confirm.

When a city list appears, you can search cities in

alphabetical order by turning the volume knob quickly.

To cancel, press and hold

To store a station: Press and hold one of the number buttons (3, 4or5). To select a stored station: Press one of the number buttons (3, 4or5).

ENGLISH

SiriusXM® Radio

Only SiriusXM® brings you more of what you love to listen to, all in one place. Get over 140 channels, including commercial-free music plus the best sports, news, talk, comedy and entertainment. Welcome to the world of satellite radio. A SiriusXM Vehicle Tuner and Subscription are required. For more information, visit <www.siriusxm.com>.

Preparation:

1 Connect the optional SiriusXM Vehicle Tuner (commercially available).

Antenna

Expansion port on the rear panel

2 Check your Radio ID for activation.

The SiriusXM Radio ID is required for activation and can be found by tuning to

Channel 0 as well as on the label found on the SiriusXM Connect tuner and its packaging.

The Radio ID does not include the letters I, O, S or F.

3 Activate the subscription.

For users in the U.S.A.:

Online: Go to <www.siriusxm.com> Phone: Call 1-866-635-2349

For users in Canada:

Online: Go to <www.siriusxm.ca/activatexm> Phone: Call 1-877-438-9677 4 Press repeatedly to select SIRIUSXM to start updating.

Start listening

Press repeatedly to select SIRIUSXM.

2 Press repeatedly to select a band. 3 Press .

“

” lights up.

SiriusXM Vehicle Tuner

SiriusXM® Radio

4 Turn the volume knob to select a category, then press the knob.

If “ALL CHANNELS” is selected, all the available channels will be

shown.

5 Turn the volume knob to select a channel, then press the knob. (or) Press S/T to search for a channel manually.

• Pressing and holding S/T changes the channel rapidly.

If a locked channel or a mature channel is selected, a pass code input screen appears. Enter the pass code to receive the channel.

To change the tuning method for S/T: Press . Each time you press “CHANNEL” (manually search for a channel) and “PRESET” (searches for a preset channel of the selected band).

Direct Access Tuning

, the tuning method switches between

(using the remote control)

1 Press DIRECT to enter Direct Access Tuning. 2 Press the number buttons to enter a channel number. 3 Press to start searching.

• To cancel, press or DIRECT.

• If no operation is done for 10seconds after step Tuning is automatically canceled.

2, Direct Access

( 16)

When channel keymode is selected...

To On the faceplate On the remote control

Select a channel

Change a channel rapidly

Store a channel of the current band

Select a stored channel of the current band

When replay keymode is selected...

To On the faceplate On the remote control

Playback/pause

Select a track

Rewind/Fast-forward

Go to Live Press 1.

Press S/T. Press S/

Press and hold S/T.

Press and hold one of the number buttons (1to6).

Press one of the number buttons (1to6).

Press

Press S/T. Press S/

Press and hold S/T.

. Press

Press and hold

S/

(Not available)

Press and hold S/

SiriusXM Keymode

Press and hold to change the keymode (channel or replay). (Default: Channel keymode)

“

” lights up when replay keymode is selected.

SmartFavorites and TuneStart™

User stored channels are recognized as SmartFavorite channels*. The SiriusXM Vehicle Tuner automatically buffers the broadcast content in the background.

• SmartFavorites feature is available with SXV200 or later SiriusXM Vehicle Tuner.

SXV300 (and later) SiriusXM Vehicle Tuner can use all 18 stored channels as SmartFavorites.

The SXV200 SiriusXM Vehicle Tuner can use 6 stored channels from the current band as SmartFavorites.

ENGLISH

SiriusXM® Radio

When you select a SmartFavorite channel, you can rewind and replay up to 30minutes of any of the missed news, talk, sports or music content.

• Playback starts from the beginning of the song if

[TUNE START]

music channels stored as a SmartFavorite.

Press one of the number buttons (1 to 6) to select a stored channel.

TuneScan™

You can get a short preview of the songs that you have missed on each of your SmartFavorite music channels or currently tuned music channel.

Press and hold seconds of the recorded music contents.

• To listen to the current song, press the volume knob to stop scanning. The unit continues playing the current song.

• To select the previous/next song, press S/T.

• To cancel scanning, press and hold the volume knob. Playback returns to the channel before you entered TuneScan.

SiriusXM settings

Press the volume knob to enter

2 Turn the volume knob to select an item (see the

following table), then press the knob.

3 Repeat step 2 until the desired item is selected/

activated or follow the instructions stated on the selected item.

4 Press and hold to exit.

To return to the previous setting item, press

is set to

[ON]

(see the following table) for most

to start scanning the first 6

[FUNCTION]

SIRIUS XM

CHANNEL LOCK

To unlock settings:

Turn the volume knob to select a number.

Press

S/T

Repeat steps 1 and 2 to enter the current pass code.

to move to the entry position.

(Initial pass code is 0000.)

Press the volume knob to confirm.

CODE SET

LOCK SETTING MATURE CH

CHANNEL EDIT

Turn the volume knob to select a number.

Press

S/T

Repeat steps 1 and 2 to enter a new 4-digit pass code.

Press the volume knob to confirm.

Repeat steps 1 to 4 to reconfirm the pass code.

•

Make a note of the new pass code to enter channel lock settings for next time.

to move to the entry position.

:Selects the SiriusXM-defined lock setting.;

the individual channels the user wants to lock.;

Turn the volume knob to select a category, then press the knob.

Turn the volume knob to select a channel you want to lock, then press the knob.

OFF

:Cancels.

USER DEFINED

“L” appears in front of the channel number.

Press and hold to exit.

CHANNEL CLEAR

TUNE START

SIGNAL LEVEL

YES

:Clears all the locked channels.; NO:Cancels.

:All qualified music channels in the SmartFavorite will start playback from the

beginning of the song.;

Shows the strength (

OFF

:Cancels.

NO SIGNAL/WEAK/GOOD/STRONG)

of the current received

signal.

BUFFER USAGE

SXM RESET YES

Displayed only when

Available only if the connected SiriusXM Vehicle Tuner is SXV200 or later that supports SmartFavorites.

Shows the memory usage (0%to

100%

) for Replay buffer.

:Resets stored channel and lock setting to default.; NO:Cancels.

[USER DEFINED]

is selected.

Default:

:Selects

ENGLISH

BLUETOOTH®

BLUETOOTH — Connection

Supported Bluetooth profiles

– Hands-Free Profile (HFP) – Advanced Audio Distribution Profile (A2DP) – Audio/Video Remote Control Profile (AVRCP) – Serial Port Profile (SPP) – Phonebook Access Profile (PBAP)

Supported Bluetooth codecs

– Sub Band Codec (SBC) – Advanced Audio Coding (AAC) – aptX codec (aptX)

Pair and connect a Bluetooth device for the first time

Press to turn on the unit.

2 Search and select this unit model name (KDC-X7**/KDC-BT7**HD/

KMR-D7**BT/KDC-X5**/KDC-BT5**U) on the Bluetooth device.

“PAIRING”

appears on the display.

“PASS XXXXXX” Device name “PRESS” “VOLUME KNOB”

• For some Bluetooth devices, you may need to enter the Personal Identification

Number (PIN) code immediately after searching.

3 Press the volume knob to start pairing.

“PAIRING OK” appears when pairing is completed. Once pairing is completed, Bluetooth connection is established automatically.

• “BT1” and/or “BT2” indicator on the faceplate lights up.

Connect the microphone

MIC (microphone input terminal)

Microphone (supplied)

Secure using cord clamps (not supplied) if necessary.

Adjust the microphone angle

Rear panel

• This unit supports Secure Simple Pairing (SSP).

• Up to five devices can be registered (paired) in total.

• Once the pairing is completed, the Bluetooth device will remain registered in the unit even if you reset the unit. To delete the paired device,

• A maximum of two Bluetooth phones and one Bluetooth audio device can be connected at any time.

However, while in BT AUDIO source, you can connect to five Bluetooth audio

devices and switch between these five devices.

• Some Bluetooth devices may not automatically connect to the unit after pairing. Connect the device to the unit manually.

• Refer to the instruction manual of the Bluetooth device for more information.

( 22)

21, [DEVICE DELETE]

Auto Pairing

When you connect iPhone/iPod touch/Android device to the USB input terminal, pairing request (via Bluetooth) is automatically activated.

Press the volume knob to pair once you have confirmed the device name.

Automatic pairing request is activated only if: – Bluetooth function of the connected device is turned on. –

[AUTO PAIRING]

– KENWOOD MUSIC PLAY application is installed on the Android device

[BROWSE MODE]

is set to

[ON]. ( 21)

is selected.

( 10)

( 9)

and

ENGLISH

BLUETOOTH®

Connect with a remote device by One-touch (NFC)

Near Field Communication (NFC) enables short-range wireless communication between the unit and remote devices such as smartphones. By holding an NFC-compatible remote device near to the N-Mark on the unit (right side of the panel), the unit and remote device proceed to complete pairing and established the BLUETOOTH connection automatically.

1 Activate the NFC function on the remote device.

Refer to the instruction manual of the remote device for more

information.

2 Hold the remote device near to the N-Mark on the unit (right

side of the panel).

The device vibrates when pairing is completed.

• Depending on the type of remote device used, the strength of the NFC signal may vary. For a stronger NFC signal, user must understand the position of the remote device’s NFC antenna and hence tap the NFC antenna with the NFC logo.

• To disconnect, hold the remote device near to the N-Mark on the unit again.

• This unit only can recognize and connect to one NFC-compatible device at a time.

BLUETOOTH — Mobile phone

Receive a call

When there is an incoming call:

• ZONE 2 illuminates in green color and flashes.

• The unit answers the call automatically if time.

( 19)

During a call:

• ZONE 1 illuminates according to the settings made for ZONE 2 illuminates in green color.

• If you turn off the unit or detach the faceplate, the Bluetooth connection is disconnected.

The following operations may differ or not available depending on the connected phone.

To On the faceplate On the remote control

First incoming call...

Answer a call

Reject a call

End a call

Press knob or one of the number buttons (1 to 6).

Press

[AUTO ANSWER]

or the volume

is set to a selected

[DISPLAY] ( 28)

Press

and

ENGLISH

BLUETOOTH®

To On the faceplate On the remote control

While talking on the first incoming call...

Answer another incoming call and hold the current call

Reject another incoming call

While having two active calls...

End current call and activate held call

Swap between the current call and held call

Adjust the phone volume

[00]

[35]

(Default:

Switch between hands-free and private talk modes

[15]

)

Improve the voice quality

While talking on the phone...

1 Press the volume knob to enter 2 Turn the volume knob to select an item (see the following table), then press the

knob.

3 Repeat step 2 until the desired item is selected or activated. 4 Press and hold to exit.

To return to the previous setting item, press .

Press

. Press .

Press

Turn the volume knob during a call.

• This adjustment will not affect the volume of the other sources.

Press

• Operations may vary according to the connected Bluetooth device.

[FUNCTION]

. Press .

during a call.

Press

( Not available )

Default:

MIC GAIN LEVEL –10

NR LEVEL LEVEL –5

ECHO CANCEL LEVEL –5

to The sensitivity of the microphone increases as the number increased.

reduction level until the least noise is being heard during a phone conversation.

cancellation delay time until the least echo is being heard during a phone conversation.

LEVEL +10(LEVEL –4

to

LEVEL +5(LEVEL 0

to

LEVEL +5(LEVEL 0

):

):Adjust the noise

):Adjust the echo

Make the settings for receiving a call

Press to enter Bluetooth mode.

1 2 Turn the volume knob to select an item (see the

following table), then press the knob.

3 Repeat step 2 until the desired item is selected or

activated.

4 Press and hold to exit.

To return to the previous setting item, press .

Default:

SETTINGS

AUTO ANSWER

BATTERY/ SIGNAL*

Functionality depends on the type of the phone used.

to30:The unit answers incoming call automatically

in the selected time (in seconds).;

AUTO

:Shows the strength of the battery and signal when the unit detects a Bluetooth device and the Bluetooth device is connected.;

OFF

:Cancels. Date is shown.

OFF

:Cancels.

ENGLISH

BLUETOOTH®

Make a call

You can make a call from the call history, phonebook, or dialing the number. Call by voice is also possible if your mobile phone has the feature.

1 Press to enter Bluetooth mode.

“(First device name)” appears.

• If two Bluetooth phones are connected, press again

to switch to another phone.

“(Second device name)” appears. 2 Turn the volume knob to select an item (see the

following table), then press the knob.

3 Repeat step 2 until the desired item is selected/activated

or follow the instructions stated on the selected item.

4 Press and hold to exit.

To return to the previous setting item, press .

CALL HISTORY

(Applicable only if the phone supports PBAP.)

Press the volume knob to select a name or a phone

number.

• “INCOMING”, “OUTGOING”, or “MISSED” is shown on the lower part of the display to indicate the previous call status.

• Press

DISP

or NAME).

• “NO DATA” appears if there is no recorded call history.

Press the volume knob to call.

to change the display category (NUMBER

PHONE BOOK

NUMBER DIAL

VOICE

BATTERY LVL LOW

NO SIGNAL/SIGNAL LVL LOW/MID/MAX*:Shows the strength of the current received signal.

Functionality depends on the type of the phone used.

(Applicable only if the phone supports PBAP.)

Turn the volume knob quickly to enter alphabet search mode (if the phonebook

contains many contacts).

The first menu (ABCDEFGHIJKLMN) appears.

• To go to the other menu (OPQRSTUVWXYZ1

• To select the desired first letter, turn the volume knob or press then press the knob.

Select “1” to search with numbers and select “

Turn the volume knob to select a name, then press the knob.

Turn the volume knob to select a phone number, then press the knob to call.

•

The phonebook of the connected phone is automatically transferred to the unit

when pairing.

•

Contacts are categorized as: HOME, OFFICE, MOBILE, OTHER, GENERAL.

•

This unit can display only non-accent letters. (Accent letters such as “Ú” is shown

as “U”.)

Turn the volume knob to select a number (0 to 9) or character ( , #, +).

Press

S/T

Repeat steps

Press the volume knob to call.

(or using the remote control)

Press the number buttons (0 to 9) to enter the phone number.

Press to call.

Speak the name of the contact you want to call or the voice command to control the phone functions.

MID/FULL*:Shows the strength of the battery.

to move the entry position.

and 2 until you finish entering the phone number.

( 21, Make a call using voice recognition)

), press

J / K

” to search with symbols.

S/T

ENGLISH

BLUETOOTH®

Make a call using voice recognition

Press and hold to activate the voice recognition of the

connected phone.

2 Speak the name of the contact you want to call or the voice

command to control the phone functions.

• Supported Voice Recognition features vary for each phone. Refer to the instruction manual of the connected phone for details.

• This unit also supports the intelligent personal assistant function of iPhone.

Settings in memory

Store a contact in memory

You can store up to 6 contacts into the number buttons (1 to 6).

1 Press to enter Bluetooth mode. 2 Turn the volume knob to select

[NUMBER DIAL]

, then press the knob.

[CALL HISTORY], [PHONE BOOK]

, or

3 Turn the volume knob to select a contact or enter a phone

number.

If a contact is selected, press the volume knob to show the

phone number.

4 Press and hold one of the number buttons (1 to 6).

“STORED” appears when the contact is stored. To erase a contact from the preset memory, select

step

2 and store a blank number.

[NUMBER DIAL]

Make a call from memory

Press to enter Bluetooth mode.

1 2 Press one of the number buttons (1 to 6). 3 Press the volume knob to call.

“NO MEMORY” appears if there is no contacts stored.

Other settings

Press the volume knob to enter

[FUNCTION]

2 Turn the volume knob to select an item (see the following table), then

press the knob.

3 Repeat step 2 until the desired item is selected/activated or follow the

instructions stated on the selected item.

4 Press and hold to exit.

To return to the previous setting item, press .

Default:

BT MODE

PHONE SELECT

AUDIO SELECT

DEVICE DELETE

PIN CODE EDIT (0000)

RECONNECT ON

AUTO PAIRING ON

INITIALIZE YES

Selects the phone or audio device to connect or disconnect. “

” appears in front of the device name when connected.

“

” appears in front of the current playback audio device.

•

You can only connect a maximum of two Bluetooth phones and one

Bluetooth audio device at any time.

Turn the volume knob to select a device to delete, then press the knob.

Turn the volume knob to select

Changes the PIN code (up to 6 digits).

Turn the volume knob to select a number.

Press S/T to move the entry position.

Repeat steps

Press the volume knob to confirm.

:The unit automatically reconnect when the last connected Bluetooth device

is within range.;

:The unit automatically pair supported Bluetooth device (iPhone/ iPod touch/Android device) when it is connected through USB input terminal.Depending on the operating system of the connected device, this function may not work. ;

:Initializes all the Bluetooth settings (including stored pairing, phonebook,

and etc.).;

and 2 until you finish entering the PIN code.

OFF

:Cancels.

OFF

:Cancels.

[YES]

[NO]

, then press the knob.

ENGLISH

BLUETOOTH®

Bluetooth test mode

You can check the connectivity of the supported profile between the Bluetooth device and the unit.

• Make sure there is no Bluetooth device paired.

1 Press and hold .

“PLEASE PAIR YOUR PHONE PIN 0000” appears.

2 Search and select this unit model name

(KDC-X7**/KDC-BT7**HD/KMR-D7**BT/ KDC-X5**/KDC-BT5**U) on the Bluetooth device.

3 Operate the Bluetooth device to confirm

pairing.

“TESTING” flashes on the display.

The connectivity result (OK or NG) appears after the test.

PAIRING: Pairing status HF CONNECT: Hands-Free Profile (HFP)

AUDIO CONNECT: Advanced Audio Distribution

PHONEBOOK DL: Phonebook Access profile

To cancel test mode, press and hold off the unit.

compatibility

Profile (A2DP) compatibility

(PBAP) compatibility

to turn

BLUETOOTH — Audio

While in BT AUDIO source, you can connect to five Bluetooth audio devices and switch between these five devices.

Audio player via Bluetooth

Press repeatedly (or press SRC on the remote control) to select BTAUDIO.

2 Operate the Bluetooth audio player to start playback.

To On the faceplate On the remote control

Playback/pause

Select group or folder

Reverse/Forward skip

Reverse/Fast-forward

Repeat play Press

Random play Press and hold

Select a file from a folder/list

Switch between connected Bluetooth audio devices

Press

Press J / K.

Press S/T. Press S/

Press and hold S/T. Press and hold S/

ALL REPEAT, FILE REPEAT, REPEAT OFF

ALL RANDOM

• Press

Refer to “Select a file from a folder/ list” on page 10.

Press 5.*

. Press

Press

repeatedly.

to select

RANDOM OFF

( Not available )

/ .

ENGLISH

Pressing the “Play” key on the connected device itself also causes switching of sound output from the device.

Operations and display indications may differ according to their availability on the connected device.

BLUETOOTH®

Settings to use KENWOOD Remote application

KENWOOD Remote application is designed to control the KENWOOD car receiver’s operations from the iPhone/iPod (via Bluetooth or via USB input terminal) or Android smartphone (via Bluetooth).

Preparation:

Install the latest version of KENWOOD Remote application on your device before connecting. For more information, visit <www.kenwood.com/cs/ce/>.

1 Press the volume knob to enter

[FUNCTION]

2 Turn the volume knob to select an item (see the following table),

then press the knob.

Repeat step 2 until the desired item is selected or activated.

4 Press and hold to exit.

To return to the previous setting item, press .

Default:

REMOTE APP

SELECT

IOS YES

ANDROID YES

ANDROID LIST

Displayed only when

Select the device (IOS or ANDROID) to use the application.

:Selects iPhone/iPod to use the application via Bluetooth or connected via USB input terminal.; If IOS is selected, select iPod BT source (or iPod 1/iPod 2/iPod USB if your iPhone/iPod is connected via USB input terminal) to activate the application.

•

The connectivity of the application will be interrupted or disconnected if:

– You change from iPod BT source to any playback source connected via

the USB input terminal.

– You change from iPod 1/iPod 2/iPod USB source to iPod BT source.

:Selects Android smartphone to use the application via Bluetooth.;

: Cancels.

*:Selects the Android smartphone to use from the list.

[ANDROID]

:Cancels.

[SELECT]

is set to

[YES]

STATUS

Shows the status of the selected device.

IOS CONNECTED

connected via Bluetooth or USB input terminal.

IOS NOT CONNECTED ANDROID CONNECTED

smartphone connected via Bluetooth.

ANDROID NOT CONNECTED

application.

: You are able to use the application using the iPhone/iPod

: No IOS device is connected to use the application.

: You are able to use the application using the Android

: No Android device is connected to use the

Listen to iPhone/iPod via Bluetooth

You can listen to the songs on the iPhone/iPod via Bluetooth on this unit.

Press repeatedly to select iPodBT.

• You can operate the iPod/iPhone in the same way as iPod/iPhone via USB input terminal.

• If you plug in an iPhone/iPod to the USB input terminal while listening to iPodBT source, the source automatically change to iPod 1/iPod 2/ iPod USB. Press Bluetooth.

( 9)

to select iPodBT if the device is still connected via

Internet radio via Bluetooth

You can listen to internet radio (Pandora and iHeartRadio) on the iPhone/ iPod/Android device via Bluetooth on this unit.

• Make sure the USB input terminal is not connected to any device.

Listen to Pandora

Preparation:

Select

[ON]

for

[PANDORA SRC]

[SOURCE SELECT]. ( 5)

1 Open the Pandora application on your device. 2 Connect your device via Bluetooth connection.

( 17)

3 Press repeatedly to select PANDORA (for iPhone/iPod) or

PANDORA BT (for Android device).

The source switches and broadcast starts automatically.

• You can operate Pandora in the same way as Pandora via USB input terminal.

( 12)

ENGLISH

BLUETOOTH®

Listen to iHeartRadio

Preparation:

Select

[ON]

for

[IHEART SRC]

1 Open the iHeartAuto application on your device. 2 Connect your device via Bluetooth connection.

( 17)

3 Press repeatedly to select IHEARTRADIO.

The source switches and broadcast starts

automatically.

• You can operate iHeartRadio in the same way as iHeartRadio via USB input terminal.

[SOURCE SELECT]. ( 5)

( 13)

AUDIO SETTINGS

While listening to any source...

1 Press AUDIO to enter 2

Turn the volume knob to select an item (see the following table), then press the knob.

3 Repeat step 2 until the desired item is selected or activated. 4 Press and hold to exit.

(or using the remote control)

1 Press AUD to enter 2 Press J / K to select an item, then press .

To return to the previous setting item, press

AUDIO CONTROL

SUB-W LEVEL

MANUAL EQ

62.5HZ LEVEL LEVEL LEVEL–9

100 HZ/160 HZ/250 HZ/ 400 HZ/630 HZ/1 KHZ/

1.6KHZ/2.5KHZ/4 KHZ/

6.3KHZ/10 KHZ/16 KHZ LEVEL

Q FACTOR 1.35/1.50/2.00

PRESET EQ NATURAL/ROCK/POPS/EASY/TOP40/JAZZ/POWERFUL/USER

[AUDIO CONTROL]

LEVEL –50

The sound elements (frequency level, tone level, Q factor) are preset into each selection.

BASS EXTEND ON

LEVEL–9

(Before making an adjustment, select the source you want to adjust.)

equalizer suitable to the music genre. (Select

[MANUAL EQ]

directly.

LEVEL +10 (LEVEL 0

for each source. (Before making an adjustment, select the source you want to adjust.)

:Turns on the extended bass.;

LEVEL +9 (LEVEL 0

:Adjust the quality factor.

): Adjusts the subwoofer output level.

LEVEL +9 (LEVEL 0

):Adjusts the level to memorize for each source.

):Adjusts the level to memorize

OFF

[USER]

to use the settings made in

:Cancels.

: Selects a preset

Default:

ENGLISH

AUDIO SETTINGS

BASS BOOST LEVEL1/LEVEL2/LEVEL3/LEVEL4/LEVEL5

LOUDNESS LEVEL1/LEVEL2

SUBWOOFER SET ON

FADER REAR 15

BALANCE LEFT 15

VOLUME OFFSET LEVEL –15

SOUND EFFECT

SOUND RECONSTRA

(Sound reconstruction)

SPACE ENHANCER

SOUND REALIZER LEVEL1/LEVEL2/LEVEL3

STAGE EQ LOW/MIDDLE/HIGH

DRIVE EQ ON

preferred bass boost level.;

frequencies boost to produce a well-balanced sound at a low volume level.;

output balance.

level of each source. (Before adjustment, select the source you want to adjust.)

(Not applicable for TUNER source, AUX source and SIRIUS XM source.)

components and restoring the rise-time of the waveform that are lost in audio data compression.;

(Not applicable for TUNER source.)

SMALL/MEDIUM/LARGE OFF

realistic.;

from the speakers.;

outside the car or running noise of the tyres.;

OFF

:Turns on the subwoofer output.;

FRONT15 (0

RIGHT15 (0

LEVEL +6 (LEVEL 0

:Creates realistic sound by compensating the high-frequency

:Cancels.

OFF

:Cancels.

: Boosts the frequency to reduce the noise heard from

OFF

:Cancels.

:Selects your preferred low and high

:Cancels.

OFF

):Adjusts the rear and front speaker

):Adjusts the left and right speaker

):Preset the initial volume

OFF

:Virtually enhances the sound space.;

:Virtually makes the sound more

:Virtually adjust the sound position heard

OFF

:Cancels.

:Selects your

:Cancels.

OFF

:Cancels.

SPEAKER SIZE

FRONT SIZE 3.5"/4"/4.75"/5"/6.5"/6.75"/7"/4×6/5×7/6×8/6×9

REAR 3.5"/4"/4.75"/5"/6.5"/6.75"/7"/4×6/5×7/6×8/6×9/7×10

SUBWOOFER 6.5"/8"/10"/12"/15" OVER

X ' OVER

TWEETER FRQ

FRONT HPF FRONT-HPF

The frequency and slope settings are automatically set for the crossover of the selected speaker.

7×10

: Selects according to the connected speaker size for

optimum performance.

TWEETER SMALL/MIDDLE/LARGE

Selects according to the connected speaker size for optimum performance.;

NONE

for optimum performance.;

GAIN LEFT

GAIN RIGHT –8

FRQ

FRONT-HPF SLOPE

FRONT-HPF GAIN

range of the connected tweeter for optimum performance.;

NONE

:Not connected.

: Selects according to the connected speaker size

NONE

1KHZ/1.6KHZ/2.5KHZ/4KHZ/5KHZ/6.3KHZ/8KHZ 10KHZ/12.5KHZ: Adjusts the crossover frequency for the

tweeter speaker.

–8

to 0:Adjusts the output volume of the left tweeter.

to 0:Adjusts the output volume of the right tweeter.

30HZ/40HZ/50HZ/60HZ/70HZ/80HZ/90HZ/100HZ 120HZ/150HZ/180HZ/220HZ/250HZ: Adjusts the crossover

frequency for the selected speakers (high pass filter).

THROUGH

: All signals are sent to the selected speakers.

–6DB/–12DB/–18DB/–24DB: Adjusts the crossover slope. (Selectable only if a setting other than for

[FRONT-HPF FRQ]

–8

to 0:Adjusts the output volume of the selected speaker.

:Selects according to the size

:Not connected.

[THROUGH]

;

is selected

ENGLISH

AUDIO SETTINGS

REAR HPF REAR-HPF FRQ

(Refer

REAR-HPF SLOPE

REAR-HPF GAIN

SUBWOOFER LPF

DTA SETTINGS

CAR SETTINGS

•

The following item is selectable only if

–

[SUB-W LEVEL]

–

[SUBWOOFER]

–

[SUBWOOFER LPF]

–

[SUBWOOFER]

•

The following item is selectable only if a setting other than

[TWEETER], [REAR]

–

[TWEETER], [REAR HPF], [SUBWOOFER LPF]

SW LPF FRQ

SW LPF SLOPE –6DB/–12DB/–18DB/–24DB: Adjusts the

SW LPF PHASE REVERSE

SW LPF GAIN –8

For settings,

Digital Time Alignment settings

[SPEAKER SIZE]

[X’OVER]

[DISTANCE]

and

[SUBWOOFER]

ENGLISH

FRONT HPF

30HZ/40HZ/50HZ/60HZ/70HZ/80HZ/90HZ 100HZ/120HZ/150HZ/180HZ/220HZ 250HZ

: Adjusts the crossover frequency for the subwoofer (low pass filter).; signals are sent to the subwoofer.

crossover slope. (Selectable only if a setting other than

[THROUGH]

the phase of the subwoofer output to be in line with the speaker output for optimum performance.

to 0:Adjusts the output volume of the

subwoofer.

[SUBWOOFER SET]

and

[GAIN]

[SPEAKER SIZE] ( 25)

settings,

is selected for

(180°)/

NORMAL

is set to

[DTA SETTINGS]

[NONE]

[X’OVER]

)

THROUGH

[SW LPF FRQ]

(0°): Selects

[ON] ( 25)

is selected for

: All

Digital Time Alignment settings

Digital Time Alignment sets the delay time of the speaker output to create a more suitable environment for your vehicle.

• For more information,

[DTA SETTINGS]

DTA SETTINGS

POSITION

DISTANCE 0FT

GAIN –8DB

DTA RESET YES

CAR SETTINGS

CAR TYPE COMPACT/FULL SIZE CAR/WAGON/MINIVAN/SUV

REAR-SP LOCATION

•

Before making an adjustment for

you want to adjust:

FRONT LEFT/FRONT RIGHT/REAR LEFT/REAR RIGHT/SUBWOOFER:

You can only select

[NONE]

• [REAR-SP LOCATION]

selected for

( 27)

is selected for

[REAR]

Determining the value for [DISTANCE] and [GAIN] of

Selects your listening position (reference point).

ALL

:Not compensating;

FRONT LEFT

adjustment, select the speaker you want to adjust.)

(Before making an adjustment, select the speaker you want to adjust.)

[POSITION]

Identify your car type and rear speaker location in order to make the adjustment for

MINIVAN(LONG)

Selects the location of the rear speakers in your vehicle to calculate the furthest distance from the listening position selected (reference point).

• DOOR/REAR DECK

• 2ND ROW/3RD ROW

[REAR LEFT], [REAR RIGHT]

:Front left seat;

20.01FT

0DB

:Resets the settings (

to default.; NO:Cancels.

[OFF], [COMPACT], [FULL SIZE CAR], [WAGON]

[MINIVAN]

[DISTANCE]

[REAR]

and

[CAR SETTINGS]

[SPEAKER SIZE]. ( 25)

FRONT RIGHT:

:Fine adjust the distance to compensate. (Before making an

:Fine adjust the output volume of the selected speaker.

[DISTANCE]

[DTA SETTINGS]

:Selects the type of vehicle.;

:Selectable only when

[MINIVAN(LONG)]

and

[SUBWOOFER]

and

is selectable only if a setting other than

Front right seat;

FRONT ALL

:Front seat

and

[GAIN]

OFF:

[CAR TYPE]

[GAIN]

[DTA SETTINGS]

[SUBWOOFER]

[SPEAKER SIZE]. ( 25)

if a setting other than

) of the selected

Not compensating.

is selected as

[SUV]

is selected as

, select the speaker

[NONE]

+ 86 hidden pages