Kenwood KDC-X700, KDC-BT765HD User Manual

KDC-X700 KDC-BT765HD

CD-RECEIVER

INSTRUCTION MANUAL

AMPLI-TUNER LECTEUR DE CD

MODE D’EMPLOI

REPRODUCTOR DE DISCOS COMPACTOS RECEPTOR DE FM/AM

MANUAL DE INSTRUCCIONES

For your records

Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below. Refer to the model and serial numbers whenever you call upon your Kenwood dealer for information or service on the product. Model KDC-X700/ KDC-BT765HD Serial number

US Residents Only

CAUTION

Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. In compliance with Federal Regulations, following are reproductions of labels on, or inside the product relating to laser product safety.

JVC KENWOOD Corporation 2967-3, ISHIKAWA-MACHI, HACHIOJI-SHI, TOKYO, JAPAN

THIS PRODUCT COMPLIES WITH DHHS RULES 21CFR SUBCHAPTER J IN EFFECT AT DATE OF MANUFACTURE.

Location : Top Plate

FCC WARNING

This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.

FCC NOTE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment may cause harmful interference to radio communications, if it is not installed and used in accordance with the instructions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Información acerca de la eliminación de equipos eléctricos y electrónicos al final de la vida útil (aplicable a los países que hayan adoptado sistemas independientes de recogida de residuos)

Los productos con el símbolo de un contenedor con ruedas tachado no podrán ser desechados como residuos domésticos. Los equipos eléctricos y electrónicos al final de la vida útil, deberán ser reciclados en instalaciones que puedan dar el tratamiento adecuado a estos productos y a sus subproductos residuales correspondientes. Póngase en contacto con su administración local para obtener información sobre el punto de recogida más cercano. Un tratamiento correcto del reciclaje y la eliminación de residuos ayuda a conservar los recursos y evita al mismo tiempo efectos perjudiciales en la salud y el medio ambiente.

Informação sobre a eliminação de pilhas

Este produto não deve ser eliminado como lixo doméstico geral. Devolva a pilha usada ao revendedor ou entidade autorizada para que a mesma seja devolvida ao fabricante ou importador. A reciclagem e a eliminação de lixo de maneira apropriada ajudarão a conservar os recursos naturais ao mesmo tempo que prevenirão os efeitos prejudicais à nossa saúde e ao meio ambiente.

CALIFORNIA, USA ONLY

This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material— special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate

IC (Industry Canada) Notice

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause

undesired operation of the device. The term “IC: ” before the certification/ registration number only signifies that the Industry Canada technical specification were met.

Note de IC (Industrie Canada)

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le

brouillage est susceptible d’en compromettre le fonctionnement. L’expression “IC:” avant le numéro d’homologation/ enregistrement signifie seulement que les specifications techniques d’Industrie Canada ont été respectées.

Para cumplimiento de la COFETEL:

“La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda

causar su operación no deseada”

Contains Bluetooth Module FCC ID: ZWY8350X IC ID: 12033A-8350X

CAUTION

This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that it deemed to comply without maximum permissive exposure evaluation (MPE). But it is desirable that it should be installed and operated keeping the radiator at least 20cm or more away from person’s body (excluding extremities: hands, wrists, feet and ankles).

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

ATTENTION

Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un environnement non contrôlé et respecte les règles d’exposition aux fréquences radioélectriques (RF) CNR-102 de l’IC. Cet équipement émet une énergie RF très faible qui est considérée conforme sans évaluation de l’exposition maximale autorisée. Cependant, cet équipement doit être installé et utilisé en gardant une distance de 20 cm ou plus entre le dispositif rayonnant et le corps (à l’exception des extrémités : mains, poignets, pieds et chevilles).

Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d’un type et d’un gain maximal (ou inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une communication satisfaisante.

SOFTWARE LICENSE AGREEMENT

The software embedded in the Product (hereinafter the "Licensed Software") provided by Licensor is copyrighted to or sublicensable by the Licensor, and this Agreement provides for the terms and conditions which Users shall follow in order to use the Licensed Software.

The User shall use the Licensed Software by agreeing with the terms of this Software License Agreement. This Agreement shall be deemed completed at the time the User (hereinafter the "User") initially used the Product in which the "Licensed Software" is embedded.

The Licensed Software may include the software which has been licensed to the Licensor directly or indirectly from any third party. In such case, some third parties require the Users to follow their conditions for use separately from this Software License Agreement. Such software shall not be subject to this Agreement, and the Users are urged to read the "Important Notice concerning the Software" to be provided separately below.

Article 3 Conditions for Grant of License

1. When the User transfers the Product, it may also transfer the license to use the Licensed Software embedded in the Product (including any related materials, updates and upgrades) on condition that no original, copies or related materials continue in the possession of the User, and that the User shall cause the transferee to comply with this Software License Agreement.

2. The User shall not carry out reverse engineering, disassembling, decompiling or any other code analysis works in connection with the Licensed Software.

Article 4 Right pertaining to the Licensed Software

Any and all copyrights and other rights pertaining to the Licensed Software and related documents shall belong to the Licensor or the original holder of the right who granted to the Licensor the license or sublicense for the Licensed Software (hereinafter the "Original Rightholder"), and the User shall not be entitled to any right other than the license granted hereunder, in respect of the Licensed Software and any related documents.

Article 1 General Provision

The Licensor shall grant to the User a non-exclusive and non-transferable (other than the exceptional case referred to in Article 3, Paragraph 1) licensed to use the Licensed Software within the country of the User. (the country where the User bought the Product(hereinafter the "Country")

Article 2 License

1. The license granted under this Agreement shall be the right to use the Licensed Software in the Product.

2. The User shall not duplicate, copy, modify, add, translate or otherwise alter, or lease the Licensed Software and any related documents, whether in whole or in part.

3. The use of the Licensed Software shall be limited to personal purpose, and the Licensed Software shall not be distributed, licensed or sub-licensed whether it is for commercial purpose or not.

4. The User shall use the Licensed Software according to the directions described in the operation manual or help file, and is prohibited to use or duplicate any data in a manner violating the Copyright Law or any other laws and regulations by applying whole or a part of the Licensed Software.

iii

Article 5 Indemnification of Licensor

1. Neither the Licensor nor the Original Rightholder shall be liable for any damage incurred by the User or any third party due to the exercise of the license granted to the User under this Agreement, unless otherwise restricted by law.

2. The Licensor will offer no guarantee for the merchantability, convertibility and consistency with certain objective of the Licensed Software.

Article 6 Liability to Third Party

If any dispute has arisen with any third party due to an infringement upon a copyright, patent or any other intellectual property right that was caused by the User's use of the Licensed Software, the User shall settle such dispute at its own cost and hold the Licensor and the Original Rightholder harmless from any inconvenience it may cause.

Article 7 Confidentiality

The User shall keep the confidentiality of such portion of the Licensed Software, related documents thereof or any other information to be granted under this Agreement, as well as the conditions of this Agreement as has not yet entered the public domain, and shall not disclose or divulge the same to any third party without approval of the Licensor.

Article 8 Termination

In case the User falls under any of the events described in the following items, the Licensor may immediately terminate this Agreement or claim that the User compensates for the damage incurred by the Licensor due to such event: (1) when the User violated any provision of this Agreement; or (2) when a petition has been filed against the User for an attachment, provisional attachment, provisional disposition or any other compulsory execution.

Article 9 Destruction of the Licensed Software

If this Agreement is terminated pursuant to the provision of Article 8, the User shall destroy the Licensed Software, any related documents and copies thereof within two (2) weeks from such date of termination.

Article 10 Protection of Copyright

1. The copyright and all the other intellectual property rights relating to the Licensed Software shall belong to the Licensor and the Original Rightholder, and in no event shall they be under the ownership of the User.

2. The User shall, whenever it uses the Licensed Software, comply with any laws relating to the copyright and other intellectual property rights.

Article 11 Export Restriction

1. It is prohibited to export the Licensed Software and any related documents outside the country of the User (including transmission thereof outside the country of the User via Internet of other communication tools).

2. The User shall understand that the Licensed Software shall be subject to the export restrictions adopted by the country of User and any other countries.

3. The User shall agree that the software will be subject to any and all applicable international and domestic laws (including the export control regulation of the country of User and any other countries, and any restrictions concerning the end-users, the use by end-users and importing countries to be provided by the country of User and any other countries, and any other governmental authorities).

Article 12 Miscellaneous

1. In the event any part of this Agreement is invalidated by operation of law, the residual provisions shall continue in force.

2. Matters not stipulated in this Agreement or any ambiguity or question raised in the construction of this Agreement shall be provided or settled upon good-faith consultation between the Licensor and the User.

3. The Licensor and the User hereby agree that this Agreement is governed by the laws of Japan, and any dispute arising from, and relating to the rights and obligations under, this Agreement shall be submitted to the exclusive jurisdiction of the Tokyo District Court for its first instance.

Important Notice concerning the Software

-jansson

Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the "Software"), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:

The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.

THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.

CONTENTS BEFORE USE

BEFORE USE 2

BASICS 3

GETTING STARTED 4

1 Select the display language

and cancel the demonstration 2 Set the clock and date 3 Set the initial settings

HD RadioTM tuner 5

CD / USB / iPod / ANDROID 7

AUX 9

Pandora® 10

iHeartRadio® 11

SiriusXM® Radio 12

BLUETOOTH® 15

AUDIO SETTINGS 21

DISPLAY SETTINGS 23

REFERENCES 24

Maintenance More information

TROUBLESHOOTING 27

INSTALLATION / CONNECTION 30

SPECIFICATIONS 32

IMPORTANT

• To ensure proper use, please read through this manual before using this product. It is especially important that you read and observe Warning and Caution in this manual.

• Please keep the manual in a safe and accessible place for future reference.

Warning

Do not operate any function that takes your attention away from safe driving.

Caution

Volume setting:

• Adjust the volume so that you can hear sounds outside the car to prevent accidents.

• Lower the volume before playing digital sources to avoid damaging the speakers by the sudden increase of the output level.

General:

• Avoid using the external device if it might hinder safe driving.

•

Make sure all important data has been backed up. We shall bear no responsibility for any loss of recorded data.

•

Never put or leave any metallic objects (such as coins or metal tools) inside the unit to prevent a short circuit.

•

If a disc error occurs due to condensation on the laser lens, eject the disc and wait for the moisture to evaporate.

• USB rating is indicated on the main unit. To view, detach the faceplate.

• Depending on the types of cars, the antenna will automatically extend when you turn on the unit with the antenna control wire connected ( a low ceiling area.

Remote control (RC-406):

• Do not leave the remote control in hot places such as on the dashboard.

• The Lithium battery is in danger of explosion if replaced incorrectly. Replace it only with the same or equivalent type.

• The battery pack or batteries shall not be exposed to excessive heat such as sunshine, fire or the like.

• Keep the battery out of reach of children and in its original packaging when not in used. Dispose of used batteries promptly. If swallowed, contact a physician immediately.

How to read this manual

• Operations are explained mainly using buttons on the faceplate of .

• English indications are used for the purpose of explanation. You can select the display language from the [

FUNCTION

• [

• (

] menu. ( 5)

] indicates the selected items.

XX) indicates references are available on the stated page.

( 3)

31). Turn off the unit or change the source to STANDBY when parking at

BASICS

Faceplate

Remote control (RC-406)

Volume knob

Detach button

To On the faceplate On the remote control

Turn on the power

Adjust the volume Turn the volume knob. Press

Select a source

Change the display information Press DISP repeatedly.

Press

• Press and hold to turn off the power.

Press

Display window

How to resetAttach Detach

repeatedly.

Press the switch twice within 5seconds after detaching the faceplate.

( 26)

How to replace the battery

Press and hold SRC to turn off the power. ( Pressing SRC does not turn on the power. )

or .

Press ATT during playback to attenuate the sound.

• Press again to cancel.

Press SRC repeatedly.

( Not available )

Remote sensor (Do not expose to bright sunlight.)

Pull out the insulation sheet when using for the first time.

ENGLISH

GETTING STARTED

Select the display language and cancel the demonstration

When you turn on the power for the first time (or [ [

YES

], 5), the display shows: “SEL LANGUAGE” “PRESS” “VOLUME

KNOB”

1 Turn the volume knob to select [

then press the knob.

[

ENG

] is selected for the initial setup.

Then, the display shows: “CANCEL DEMO”

KNOB”.

ENG

2 Press the volume knob.

[

YES

] is selected for the initial setup.

3 Press the volume knob again.

“DEMO OFF” appears.

Set the clock and date

Press the volume knob to enter [

1 2 Turn the volume knob to select [

To adjust the clock

3 Turn the volume knob to select [

FUNCTION CLOCK

CLOCK ADJUST

4 Turn the volume knob to make the settings, then press the knob.

Hour

5 Turn the volume knob to select [ 6 Turn the volume knob to select [

Minute

CLOCK FORMAT 12H

FACTORY RESET

] (English) or [

], then press the knob.

] or [

SPA

] (Spanish),

“PRESS” “VOLUME

], then press the knob.

24H

], then press the knob.

] is set to

To set the date

7 Turn the volume knob to select [ 8 Turn the volume knob to select [

the knob.

9 Turn the volume knob to select [

DATE FORMAT DD/MM/YY

DATE SET

], then press the knob.

] or [

], then press the knob.

MM/DD/YY

], then press

10 Turn the volume knob to make the settings, then press the knob.

Day

Month Year or Month Day Year

11 Press and hold to exit.

To return to the previous setting item, press .

Set the initial settings

Press repeatedly to enter STANDBY.

1 2 Press the volume knob to enter [

FUNCTION

3 Turn the volume knob to select an item (see the following table),

then press the knob.

4 Repeat step 3 until the desired item is selected or activated. 5 Press and hold to exit.

To return to the previous setting item, press .

Default:

DISPLAY

EASY MENU

TUNER SETTING

PRESET TYPE

When entering [

:ZONE1 and ZONE2 illuminations change to white color.; and ZONE2 illuminations remain as [ (Refer to the illustration on page 23 for zone identification.)

NORMAL

(FM1/ FM2/ FM3/ AM).; for each preset button, regardless of the selected band or SiriusXM channel.

FUNCTION

]...

COLORSELECT

:Memorizes one station for each preset button in each band

MIX

:Memorizes one station or SiriusXM channel

] colors. ( 24)

OFF

:ZONE1

GETTING STARTED

SYSTEM

KEY BEEP

SOURCE SELECT

PANDORA SRC

IHEART SRC ON

BUILT-IN AUX ON

CD READ 1

F/W UPDATE

UPDATE SYSTEM/ UPDATE HD

F/W UP xx.xx

FACTORY RESET YES

CLOCK

CLOCK DISPLAY

ENGLISH

ESPANOL

:Activates the keypress tone.;

:Enables PANDORA in source selection.;

:Enables IHEARTRADIO in source selection.;

:Enables AUX in source selection.;

:Automatically distinguishes between audio file disc and music CD.;

:Forces to play as a music CD. No sound can be heard if an audio file disc is

played.

YES

:Starts upgrading the firmware.; NO:Cancels (upgrading is not activated). For details on how to update the firmware, see: www.kenwood.com/cs/ce/

:Resets the settings to default (except the stored station).; NO:Cancels.

:The clock time is shown on the display even when the unit is turned off.;

OFF

:Cancels.

Select the display language for [ applicable. By default, [

ENGLISH

] is selected.

OFF

:Deactivates.

OFF

:Disables. ( 10)

OFF

:Disables. ( 9)

FUNCTION

] menu and music information if

:Disables. ( 11)

HD Radio™ tuner

You can tune in to both conventional and HD Radio broadcasts.

• To find HD Radio stations in your area, visit <http://www.hdradio.com>.

Search for a station

Press repeatedly to select HD RADIO.

1 2 Press repeatedly (or press / on RC-406)

to select FM1/ FM2/ FM3/ AM.

3 Press S/T (or press S/ on RC-406) to search for a

station or channel.

• To change the searching method for S/T: Press repeatedly.

AUTO1 : Automatically search for a station or channel. AUTO2 : Search for a preset station or channel. MANUAL : Manually search for a station or channel.

• To store a station or channel: Press and hold one of the number buttons (1to6).

• To select a stored station or channel: Press one of the number buttons (1to6) (or press one of the number buttons (1to6) on RC-406).

ENGLISH

HD Radio™ tuner

Direct Access Tuning (using RC-406)

Press DIRECT to enter Direct Access Tuning.

1 2 Press the number buttons to enter a frequency. 3 Press to search for a station or channel.

• To cancel, press or DIRECT.

• If no operation is done for 10seconds after step is automatically canceled.

Select an HD Radio multicast channel

Many HD Radio stations offer more than one channel programming. This service is called multicasting. While receiving HD Radio multicast

channels....

Press S

“LINKING” appears while linking to a multicast channel.

/

T to select your desired channel (HD1 to HD8).

Other settings

Press the volume knob to enter [

FUNCTION

2 Turn the volume knob to select an item (see the following table),

then press the knob.

3 Repeat step 2 until the desired item is selected or activated. 4 Press and hold to exit.

To return to the previous setting item, press .

2, Direct Access Tuning

TUNER SETTING

IF BAND

AUTO MEMORY YES

RECEIVE MODE

CLOCK

TIME SYNC

Default:

AUTO

:Increases the tuner selectivity to reduce interference noises from adjacent FM stations. (Stereo effect may be lost.); interference noises from adjacent FM stations, but sound quality will not be degraded and the stereo effect will remain.

:Automatically starts memorizing 6 stations with good reception.;

:Cancels.

•

Selectable only if [

Sets the receive mode of the HD Radio receiver.

AUTO

:Automatically tunes to analog broadcast when there is no digital broadcast.;

ANALOG

:Synchronizes the unit’s time to the Radio Broadcast Data System

station time.;

NORMAL

] is selected for [

DIGITAL

:Tunes in to analog broadcast only.

OFF

:Tunes in to digital broadcast only.;

:Cancels.

WIDE

PRESET TYPE

:Subjects to

]. ( 4)

CD / USB / iPod / ANDROID

Start playback

The source changes automatically and playback starts.

Label side

USB input terminal

KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type

Do not leave the cable inside the car when not using.

Eject disc

USB

CA-U1EX (max.: 500mA) (optional accessory)

iPod/iPhone

KCA-iP102 / KCA-iP103 (optional accessory) or accessory cable of the iPod/iPhone

ANDROID

Micro USB 2.0 cable (commercially available)

To On the faceplate On the remote control

Playback / pause Press .

Reverse / Fast-forward

Select a track/file

Select a folder

Repeat play

Press and hold S/T. Press and hold S/ .

Press S/T. Press S/

Press J/K.

Press repeatedly.

TRACK REPEAT/ ALL REPEAT FILE REPEAT/ FOLDER REPEAT/ ALL REPEAT

: Audio CD

Press

/ .

: MP3/WMA/AAC/WAV/FLAC

file

Random play

FILE REPEAT/ FOLDER REPEAT/ REPEAT OFF

Press repeatedly.

DISC RANDOM/ RANDOM OFF FOLDER RANDOM/ RANDOM OFF

: Audio CD

: iPod or ANDROID

: MP3/WMA/AAC/WAV/FLAC file, iPod

or ANDROID

Press and hold

When connecting an Android device, “Press [VIEW] to install KENWOOD MUSIC PLAY APP” is shown. Follow the

to select

ALL RANDOM

instructions to install the application. You can also install the latest version of KENWOOD MUSIC PLAY application on your Android device before connecting. (

For ANDROID: Applicable only when [

For CD: Only for MP3/WMA/AAC files. This does not work for iPod/ ANDROID.

For iPod/ ANDROID: Applicable only when [

For CD: Only for MP3/WMA/AAC files.

24)

BROWSE MODE

MODE OFF

] is selected. ( 8)

]/ [

BROWSE MODE

] is selected. ( 8)

ENGLISH

CD / USB / iPod / ANDROID

Select control mode

While in iPod source, press 5 repeatedly.

MODE ON

: Control iPod using the iPod itself

still play/pause, file skip, fast-forward or reverse from

MODE OFF

While in ANDROID source, press 5 repeatedly.

BROWSE MODE

HAND MODE

this unit.

: Control iPod from this unit.

: Control Android device from this unit via

KENWOOD MUSIC PLAY application installed in the Android device.

: Control Android device using the Android

device itself via other media player applications installed in the Android device. However, you can still play/pause and file skip from this unit.

. However,

you can

Select music drive

Press 5 repeatedly.

Stored songs in the following drive will be played back.

• Selected internal or external memory of a smartphone (Mass Storage Class).

• Selected drive of a multiple drives device.

Listen to TuneIn Radio/ TuneIn Radio Pro/ Aupeo

While listening to TuneIn Radio, TuneIn Radio Pro or Aupeo, connect the iPod/iPhone to the USB input terminal of the unit.

• The unit will output the sound from these applications.

Select a file from a folder/list

Press .

1 2 Turn the volume knob to select a folder/list, then press the knob. 3 Turn the volume knob to select a file, then press the knob.

Quick Search

If you have many files, you can search through them quickly.

Turn the volume knob quickly to browse through the list quickly.

–

Not applicable for iPod.

(or)

Press S/T to search at a preset skip search ratio. (

• Pressing and holding S/T searches at a 10

– Not applicable for audio CD and MP3/WMA/AAC/WAV/FLAC files.

(or)

Alphabet search

If you have many files in the iPod, you can search through them quickly according to the first character of the file name.

(applicable only for iPod)

9, [SKIP SEARCH

ratio.

Turn the volume knob quickly to enter character search. Turn the volume knob to select the character.

To search for a character other than A to Z and 0to9, enter only “ * ”.

Press S/T to move to the entry position.

• You can enter up to 3characters.

Press the volume knob to start searching.

• To return to the root folder/ first file/ top menu, press 5. (

source.

)

• To return to the previous setting item, press

• To cancel, press and hold

• For iPod, applicable only when [

• For ANDROID, applicable only when [

MODE OFF

BROWSE MODE

] is selected.

Not applicable for BT AUDIO

] is selected.

])

CD / USB / iPod / ANDROID

Direct Music Search (using RC-406)

Press DIRECT.

1 2 Press the number buttons to enter a track/file number. 3 Press to search for music.

• To cancel, press or DIRECT.

• Not available if Random Play is selected.

• Not applicable for iPod and ANDROID.

Other settings

Press the volume knob to enter [

1 2 Turn the volume knob to select an item (see the following table),

then press the knob.

3 Repeat step 2 until the desired item is selected or activated. 4 Press and hold to exit.

To return to the previous setting item, press .

USB

MUSIC DRIVE DRIVE CHANGE

SKIP SEARCH 0.5%/ 1%/ 5%/ 10%

automatically and playback starts. Repeat steps

search ratio over the total files.

to 3 to select the following drives.

FUNCTION

:The next drive ([

DRIVE 1

] to [

DRIVE 4

]) is selected

: While listening to iPod or ANDROID, selects the skip

Default:

AUX

Preparation:

Select [

] for [

BUILT-IN AUX

Start listening

Connect a portable audio player (commercially available).

Auxiliary input jack

3.5mm (1/8") stereo mini plug with “L” shaped connector (commercially available)

2 Press repeatedly to select AUX. 3 Turn on the portable audio player and start playback.

Set the AUX name

While listening to a portable audio player connected to the unit...

1 Press the volume knob to enter [ 2 Turn the volume knob to select [ 3 Turn the volume knob to select [ 4 Turn the volume knob to select an item, then press the knob.

AUX

(default)/

5 Press and hold to exit.

To return to the previous setting item, press .

]. ( 5)

Portable audio player

FUNCTION SYSTEM

], then press the knob.

AUX NAME SET

DVD/ PORTABLE/ GAME/ VIDEO/ TV

], then press the knob.

ENGLISH

Pandora®

Preparation:

Install the latest version of the Pandora application on your device (iPhone/ iPod touch), then create an account and log in to Pandora.

• Select [

] for [

PANDORA SRC

Start listening

Open the Pandora application on your device.

1 2 Connect your device to the USB input terminal.

USB input terminal

3 Press repeatedly to select PANDORA.

Broadcast starts automatically.

To On the faceplate On the remote control

Playback / pause

Skip a track

Thumbs up or thumbs

down

KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type

Do not leave the cable inside the car when not using.

If thumbs down is selected, the current track is skipped.

]. ( 5)

KCA-iP102 / KCA-iP103 (optional accessory) or accessory cable of the iPod/iPhone

Press

Press T.

Press J/K.

. Press

Press

/ .

Create and save a new station

Press .

1 2 Turn the volume knob to select [ 3 Turn the volume knob to select [

press the knob.

A new station is created based on the current song or artist.

NEW STATION FROM TRACK

], then press the knob.

] or [

FROM ARTIST

], then

4 Press and hold one of the number buttons (1to5) to store.

To select a stored station, press one of the number buttons (1to5).

Search for a registered station

Press .

1 2 Turn the volume knob to select an item, then press the knob.

[

SORT BY DATE

[

SORT BY A-Z

]:According to the registered date

]:Alphabetical order

3 Turn the volume knob to select the desired station, then press the

knob.

To cancel, press and hold

(or using RC-406)

Press J / K to search for a station, then press .

Bookmark current song information

Press and hold the volume knob.

“BOOKMARKED” appears and the information is stored to your device. The bookmark is available on your Pandora account but not on this unit.

Pandora®

Delete a station

While listening to PANDORA...

1 Press the volume knob to enter [ 2 Turn the volume knob to select [

press the knob.

3 Turn the volume knob to select [

then press the knob.

4 Turn the volume knob to select [

[

SORT BY DATE

], then press the knob.

5 Turn the volume knob to select the desired

station to delete, then press the knob.

6 Turn the volume knob to select [

press the knob.

7 Press and hold to exit.

To return to the previous setting item, press .

FUNCTION SYSTEM

], then

STATION DEL

SORT BY A-Z

YES

], then

] or

iHeartRadio®

Preparation:

Install the latest version of iHeartAuto application on your device (iPhone/ iPod touch), then create an account and log in to iHeartRadio.

• Select [

] for [

IHEART SRC

Start listening

Open the iHeartAuto application on your device.

1 2 Connect your device to the USB input terminal.

USB input terminal

3 Press repeatedly to select IHEARTRADIO.

Broadcast starts automatically.

KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type

Do not leave the cable inside the car when not using.

To On the faceplate On the remote control

Playback / pause

Skip a track for custom station

Thumbs up or thumbs down

Create a new/custom station Press 1. ( Not available )

Scan for live station

]. ( 5)

KCA-iP102 / KCA-iP103 (optional accessory) or accessory cable of the iPod/iPhone

Press

Press T.

Press J/K.

1 2

. Press

Press 2 to start scanning. Press to listen to the station.

Press

( Not available )

ENGLISH

iHeartRadio®

Search and store a station

Press .

1 2 Turn the volume knob to select a category,

then press the knob.

3 Turn the volume knob to select the desired

station, then press the knob.

When a city list appears, you can search cities in

alphabetical order by turning the volume knob quickly.

To cancel, press and hold

(or using RC-406)

Press J / K to search for a station, then press

• To store a station: Press and hold one of the number buttons (3to5).

• To select a stored station: Press one of the number buttons (3to5).

SiriusXM® Radio

Only SiriusXM® brings you more of what you love to listen to, all in one place. Get over 140 channels, including commercial-free music plus the best sports, news, talk, comedy and entertainment. Welcome to the world of satellite radio. A SiriusXM Vehicle Tuner and Subscription are required. For more information, visit www.siriusxm.com.

Preparation:

1 Connect the optional SiriusXM Vehicle Tuner (commercially available).

Antenna

Expansion port on the rear panel

2 Check your Radio ID for activation.

The SiriusXM Radio ID is required for activation and can be found by tuning to Channel 0 as

well as on the label found on the SiriusXM Connect tuner and its packaging.

The Radio ID does not include the letters I, O, S or F.

3 Activate the subscription.

For users in the U.S.A.:

Online: Go to www.siriusxm.com Phone: Call 1-866-635-2349

For users in Canada:

Online: Go to www.siriusxm.ca/activatexm Phone: Call 1-877-438-9677 4 Press repeatedly to select SIRIUSXM to start updating.

Start listening

Press repeatedly to select SIRIUSXM.

1 2 Press repeatedly to select a band. 3 Press .

“

” lights up.

4 Turn the volume knob to select a category, then press the knob.

If “ALL CHANNELS” is selected, all the available channels will be shown.

SiriusXM Vehicle Tuner

SiriusXM® Radio

5 Turn the volume knob to select a channel, then press

the knob.

(or) Press S / T to search for a channel manually.

• Pressing and holding S / T changes the channel

rapidly.

If a locked channel or a mature channel is selected, a pass code input screen appears. Enter the pass code to receive the channel. (

To change the tuning method for S/T: Press

. Each time you press between “CHANNEL” (manually search for a channel) and “PRESET” (searches for a preset channel of the selected band).

Direct Access Tuning (using RC-406)

Press DIRECT to enter Direct Access Tuning.

1 2 Press the number buttons to enter a channel number. 3 Press to start searching.

• To cancel, press or DIRECT.

• If no operation is done for 10seconds after step

Access Tuning is automatically canceled.

SiriusXM Keymode

Press and hold to change the keymode (channel or replay). (Default: Channel keymode)

“

” lights up when replay keymode is selected.

14)

, the tuning method switches

2, Direct

When channel keymode is selected...

To On the faceplate On the remote control

Select a channel

Change a channel rapidly

Store a channel of the current band

Select a stored channel of the current band

When replay keymode is selected...

To On the faceplate On the remote control

Playback / pause

Select a track

Rewind / Fast-forward

Go to Live Press 1.

Press S/T. Press S /

Press and hold S/T. Press and hold S /

Press and hold one of the number buttons (1to6).

Press one of the number buttons (1to6).

Press

Press S/T. Press S/

Press and hold S/T. Press and hold S/

. Press

(Not available)

SmartFavorites and TuneStart™

User stored channels are recognized as SmartFavorite channels*. The SiriusXM Vehicle Tuner automatically buffers the broadcast content in the background.

• SmartFavorites feature is available with SXV200 or later SiriusXM Vehicle Tuner. *

SXV300 (and later) SiriusXM Vehicle Tuner can use all 18 stored channels as SmartFavorites. The SXV200

SiriusXM Vehicle Tuner can use 6 stored channels from the current band as SmartFavorites.

When you select a SmartFavorite channel, you can rewind and replay up to 30minutes of any of the missed news, talk, sports or music content.

• Playback starts from the beginning of the song if [ most music channels stored as a SmartFavorite.

Press one of the number buttons (1 to 6) to select a stored channel.

TUNE START

] is set to [ON] ( 14) for

ENGLISH

SiriusXM® Radio

TuneScan™

You can get a short preview of the songs that you have missed on each of your SmartFavorite music channels or currently tuned music channel.

Press and hold of the recorded music contents.

• To listen to the current song, press the volume knob to stop scanning. The unit continues playing the current song.

• To select the previous/next song, press S/T.

• To cancel scanning, press and hold the volume knob. Playback returns to the channel before you entered TuneScan.

SiriusXM settings

Press the volume knob to enter [

1 2 Turn the volume knob to select [

knob.

3 Turn the volume knob to select an item (see the following

table), then press the knob.

4 Repeat step 3 until the desired item is selected/activated

or follow the instructions stated on the selected item.

5 Press and hold to exit.

To return to the previous setting item, press .

to start scanning the first 6 seconds

FUNCTION

SIRIUS XM

], then press the

CHANNEL LOCK

To unlock settings:

Turn the volume knob to select a number.

Press

S / T

Repeat steps 1 and 2 to enter the current pass code.

to move to the entry position.

(Initial pass code is 0000.)

Press the volume knob to confirm.

CODE SET

LOCK SETTING MATURE CH

CHANNEL EDIT

Turn the volume knob to select a number.

Press

S / T

Repeat steps 1 and 2 to enter a new 4-digit pass code.

Press the volume knob to confirm.

Repeat steps 1 to 4 to reconfirm the pass code.

•

Make a note of the new pass code to enter channel lock settings for next time.

to move to the entry position.

:Selects the SiriusXM-defined lock setting.;

the individual channels the user wants to lock.;

Turn the volume knob to select a category, then press the knob.

Turn the volume knob to select a channel you want to lock, then press the

OFF

:Cancels.

USER DEFINED

knob. “L” appears in front of the channel number.

Press and hold to exit.

CHANNEL CLEAR

TUNE START

SIGNAL LEVEL NO SIGNAL/ WEAK/ GOOD/ STRONG

YES

:Clears all the locked channels.; NO:Cancels.

:All qualified music channels in the SmartFavorite will start playback from the

beginning of the song.;

OFF

:Cancels.

:Shows the strength of the current received

signal.

BUFFER USAGE 0%

SXM RESET YES

Displayed only when [

Available only if the connected SiriusXM Vehicle Tuner is SXV200 or later that supports SmartFavorites.

—

100%(0

):Shows the memory usage for Replay buffer.

:Resets stored channel and lock setting to default.; NO:Cancels.

USER DEFINED

] is selected.

Default:

:Selects

BLUETOOTH®

BLUETOOTH — Connection

Supported Bluetooth profiles

– Hands-Free Profile (HFP) – Advanced Audio Distribution Profile (A2DP) – Audio/Video Remote Control Profile (AVRCP) – Serial Port Profile (SPP) – Phonebook Access Profile (PBAP)

Supported Bluetooth codecs

– Sub Band Codec (SBC) – Advanced Audio Coding (AAC) – aptX Codec (aptX)

Connect the microphone

MIC (Microphone input terminal)

Adjust the microphone angle

Rear panel

Secure using cord clamps (not supplied) if necessary.

Microphone (supplied)

Pair and connect a Bluetooth device for the first time

Press to turn on the unit.

1 2 Search and select this unit model name (KDC-X7

device.

“PAIRING”

display.

“PASS XXXXXX” Device name “PRESS” “VOLUME KNOB” scrolls on the

/ KDC-BT7**HD) on the Bluetooth

• For some Bluetooth devices, you may need to enter the Personal Identification Number

(PIN) code immediately after searching.

3 Press the volume knob to start pairing.

“PAIRING OK” appears when pairing is completed.

• This unit supports Secure Simple Pairing (SSP).

• Up to 10 devices can be registered (paired) in total.

• Once the pairing is completed, the Bluetooth device will remain registered in the unit even if you reset the unit. To delete the paired device,

Once pairing is completed, Bluetooth connection is established automatically. “BT1” and/or “BT2” on the display window lights up.

• A maximum of two Bluetooth phones and one Bluetooth audio device can be connected at any time.

• Some Bluetooth devices may not automatically connect to the unit after pairing. Connect the device to the unit manually.

• Refer to the instruction manual of the Bluetooth device for more information.

19, [

DEVICE DELETE

Auto Pairing

When you connect iPhone/ iPod touch/ Android device to the USB input terminal, pairing request (via Bluetooth) is automatically activated.

Press the volume knob to pair once you have confirmed the device name.

Automatic pairing request is activated only if: – Bluetooth function of the connected devcie is turned on. – [

AUTO PAIRING

– KENWOOD MUSIC PLAY application is installed on the Android device (

MODE

] is set to [ON]. ( 19)

] is selected ( 8).

7) and [

BROWSE

ENGLISH

BLUETOOTH®

Connect with a remote device by One-touch (NFC)

Near Field Communication (NFC) enables short-range wireless communication between the unit and remote devices. By holding an NFC-compatible remote device near to the N-Mark on the unit (volume knob), the unit and remote device proceed to complete pairing and established the BLUETOOTH connection automatically.

1 Activate the NFC function on the remote device.

Refer to the instruction manual of the remote device

for more information.

2 Hold the remote device near to the N-Mark on the

unit (volume knob).

The device vibrates when pairing is completed.

• To disconnect, hold the remote device near to the N-Mark on the unit (volume knob) again.

• This unit only can recognize and connect to one NFCcompatible device at a time.

BLUETOOTH — Mobile phone

Receive a call

When there is an incoming call:

• The unit answers the call automatically if [ During a call:

• The buttons and display illuminate according to the settings made for [

• If you turn off the unit or detach the faceplate, the Bluetooth connection is disconnected.

The following operations may differ or not available depending on the connected phone.

To On the faceplate On the remote control

First incoming call...

Answer a call

Reject a call

End a call

Press or one of the number buttons (1 to 6).

Press

AUTO ANSWER

or the volume knob

] is set to a selected time. ( 17)

Press

DISPLAY

]. ( 23)

BLUETOOTH®

To On the faceplate On the remote control

While talking on the first incoming call...

Answer another incoming call and hold the current call

Reject another incoming call

While having two active calls...

End current call and activate held call

Swap between the current call and held call

Adjust the phone volume

[00]

[35]

(Default:

Switch between hands-free and private talk modes

[15]

)

Improve the voice quality

While talking on the phone...

1 Press the volume knob to enter [ 2 Turn the volume knob to select an item (see the following table), then press the knob. 3 Repeat step 2 until the desired item is selected or activated. 4 Press and hold to exit.

To return to the previous setting item, press .

Press

. Press .

Press

Turn the volume knob during a call.

• This adjustment will not affect the volume of the other sources.

Press

• Operations may vary according to the connected Bluetooth device.

FUNCTION

. Press .

during a call.

Press

( Not available )

Default:

MIC GAIN –10

NR LEVEL –5

ECHO CANCEL –5

—

+10(–4

microphone increases as the number increased.

—+5(0):Adjust the noise reduction level until the least noise is being heard during a phone conversation.

—+5(0):Adjust the echo cancellation delay time until the least echo is being heard during a phone conversation.

):The sensitivity of the

Make the settings for receiving a call

Press to enter Bluetooth mode.

1 2 Turn the volume knob to select an item (see the

following table), then press the knob.

3 Repeat step 2 until the desired item is selected

or activated.

4 Press and hold to exit.

To return to the previous setting item, press .

Default:

SETTINGS

AUTO ANSWER

BATT/SIGNAL*AUTO

Functionality depends on the type of the phone used.

—30:The unit answers incoming call automatically in the selected time (in seconds).;

OFF

:Cancels.

:Shows the strength of the battery and signal when the unit detects a Bluetooth device and the Bluetooth device is connected.;

OFF

:Cancels. Clock time is shown.

ENGLISH

BLUETOOTH®

Make a call

You can make a call from the call history, phonebook, or dialing the number. Call by voice is also possible if your mobile phone has the feature.

1 Press to enter Bluetooth mode. 2 Turn the volume knob to select an item (see the following table), then press the

knob.

3 Repeat step 2 until the desired item is selected/activated or follow the

instructions stated on the selected item.

4 Press and hold to exit.

To return to the previous setting item, press .

CALL HISTORY

PHONE BOOK

(Applicable only if the phone supports PBAP)

Press the volume knob to select a name or a phone number.

• “INCOMING”, “OUTGOING”, or “MISSED” is shown on the lower part of the display to indicate the previous call status.

• Press

DISP

• “NO DATA” appears if there is no recorded call history.

Press the volume knob to call.

(Applicable only if the phone supports PBAP)

Turn the volume knob quickly to enter alphabet search mode (if the phonebook

contains many contacts).

The first menu (ABCDEFGHIJK) appears.

• To go to the other menu (LMNOPQRSTUV or WXYZ1

• To select the desired first letter, turn the volume knob or press press the knob.

Select “1” to search with numbers and select “

Turn the volume knob to select a name, then press the knob.

Turn the volume knob to select a phone number, then press the knob to call.

•

The phonebook of the connected phone is automatically transferred to the unit when

pairing.

•

Contacts are categorized as: HOME, OFFICE, MOBILE, OTHER, GENERAL

•

This unit can display only non-accent letters. (Accent letters such as “Ú” is showns as

“U”.)

to change the display category (NUMBER or NAME).

), press

” to search with symbols.

J / K

S / T

, then

NUMBER DIAL

VOICE

BATT LOW/ MID/ FULL*:Shows the strength of the battery.

NO SIGNAL/ LOW/ MID/ MAX*:Shows the strength of the current received

signal.

Functionality depends on the type of the phone used.

Turn the volume knob to select a number (0 to 9) or

character (

Press

Repeat steps phone number.

Press the volume knob to call.

(or using RC-406)

Press the number buttons (0 to 9) to enter the phone

number.

Press to call.

Speak the name of the contact you want to call or the voice command to control the phone functions. (



, #, +).

S / T

Make a call using voice recognition

to move the entry position.

and 2 until you finish entering the

)

Make a call using voice recognition

Press and hold to activate the voice recognition of

the connected phone.

2 Speak the name of the contact you want to call or the

voice command to control the phone functions.

• Supported Voice Recognition features vary for each phone. Refer to the instruction manual of the connected phone for details.

• This unit also supports the intelligent personal assistant function of iPhone.

BLUETOOTH®

Settings in memory

Store a contact in memory

You can store up to 6 contacts into the number buttons (1 to 6).

1 Press to enter Bluetooth mode. 2 Turn the volume knob to select [

[

NUMBER DIAL

], then press the knob.

3 Turn the volume knob to select a contact or enter a phone number.

If a contact is selected, press the volume knob to show the phone

number.

4 Press and hold one of the number buttons (1 to 6).

“STORED” appears when the contact is stored. To erase a contact from the preset memory, select [

and store a blank number.

Make a call from memory

Press to enter Bluetooth mode.

1 2 Press one of the number buttons (1 to 6). 3 Press the volume knob to call.

“NO MEMORY” appears if there is no contacts stored.

Other settings

Press the volume knob to enter

1 2 Turn the volume knob to select an item (see the following table),

then press the knob.

3 Repeat step 2 until the desired item is selected/activated or follow

the instructions stated on the selected item.

4 Press and hold to exit.

To return to the previous setting item, press .

CALL HISTORY

[FUNCTION

], [

PHONE BOOK

NUMBER DIAL

], or

] in step 2

BT MODE

PHONE SELECT

AUDIO SELECT

DEVICE DELETE

PIN CODE EDIT (0000)

RECONNECT ON

AUTO PAIRING ON

INITIALIZE YES

Default:

Selects the phone or audio device to connect or disconnect. “

” appears in front of the device name when connected.

•

You can only connect a maximum of two Bluetooth phones and one

Bluetooth audio device at any time.

Turn the volume knob to select a device to delete, then press the

knob.

Turn the volume knob to select [

Changes the PIN code (up to 6 digits).

Turn the volume knob to select a number.

Press S/T to move the entry position.

Repeat steps

Press the volume knob to confirm.

:The unit automatically reconnect when the last connected

Bluetooth device is within range.;

:The unit automatically pair supported Bluetooth device (iPhone/ iPod touch/ Android device) when it is connected through USB input terminal.Depending on the operating system of the connected device, this function may not work. ;

:Initializes all the Bluetooth settings (including stored pairing,

phonebook, and etc.).;

and 2 until you finish entering the PIN code.

OFF

:Cancels.

YES

] or [NO], then press the knob.

OFF

:Cancels.

ENGLISH

BLUETOOTH®

Bluetooth test mode

You can check the connectivity of the supported profile between the Bluetooth device and the unit.

• Make sure there is no Bluetooth device paired.

1 Press and hold .

“PLEASE PAIR YOUR PHONE PIN 0000” appears.

2 Search and select this unit model name

(KDC-X7 device.

3 Operate the Bluetooth device to confirm

pairing.

“TESTING” flashes on the display.

The connectivity result (OK or NG) appears after the test.

PAIRING: Pairing status HF CNT: Hands-Free Profile (HFP) compatibility AUD CNT: Advanced Audio Distribution Profile

PB DL: Phonebook Access profile (PBAP)

To cancel test mode, press and hold off the unit.

/ KDC-BT7**HD) on the Bluetooth

(A2DP) compatibility

compatibility

to turn

BLUETOOTH — Audio

Audio player via Bluetooth

Press repeatedly to select BTAUDIO (or press SRC on RC-406).

1 2 Operate the Bluetooth audio player to start playback.

To On the faceplate On the remote control

Playback / pause

Select group or folder

Reverse / Forward skip

Reverse / Fast-forward

Repeat play Press

Random play Press and hold

Select a file from a folder/list

Operations and display indications may differ according to their availability on the connected device.

Press

Press J / K.

Press S/T. Press S/

Press and hold S/T. Press and hold S/

ALL REPEAT, FILE REPEAT, REPEAT OFF

ALL RANDOM

• Press

Refer to “Select a file from a folder/list” on page 8.

. Press

Press

repeatedly.

to select

RANDOM OFF

( Not available )

/ .

BLUETOOTH®

Internet radio via Bluetooth

Listen to Pandora

You can listen to Pandora on the Android device via Bluetooth on this unit.

Preparation:

Select [

] for [

PANDORA SRC

1 Open the Pandora application on your device. 2 Connect your Bluetooth audio player via Bluetooth connection.

(

15)

3 Press repeatedly to select PANDORA.

The source switches and broadcast starts automatically. You can operate Pandora in the same way as Pandora for iPod/iPhone.

(

10)

Listen to iHeartRadio

You can listen to iHeartRadio on the Android device via Bluetooth on this unit.

Preparation:

Select [

] for [

IHEART SRC

1 Open the iHeartAuto application on your smart phone. 2 Connect your smart phone via Bluetooth connection. (  3 Press repeatedly to select IHEARTRADIO.

The source switches and broadcast starts automatically. You can operate iHeartRadio in the same way as iHeartRadio for iPod/

iPhone. (

11)

]. ( 5)

)

AUDIO SETTINGS

While listening to any source...

1 Press the volume knob to enter [ 2 Turn the volume knob to select [

knob.

3 Turn the volume knob to select an item (see the following table),

then press the knob.

4 Repeat step 3 until the desired item is selected or activated. 5 Press and hold to exit.

(or using RC-406)

1 Press AUD to enter [

AUDIO CONTROL

2 Press J / K to select an item, then press .

To return to the previous setting item, press

SUB-W LEVEL –50

MANUAL EQ

BAND1 LEVEL LEVEL

BAND2 LEVEL BAND13 LEVEL

Q FACTOR 1.35/ 1.50/ 2.00

PRESET EQ NATURAL/ ROCK/ POPS/ EASY/ TOP40/ JAZZ/ POWERFUL/ USER

BASS BOOST LEVEL1/ LEVEL2/ LEVEL3/ LEVEL4/ LEVEL5

+10 (0

BASS EXTEND ON

–9

to +9 (0): The sound elements (frequency level, tone level, Q factor) are preset into each selection ( Adjusts the level to memorize for each source. (Before making an adjustment, select the source you want to adjust.)

Selects a preset equalizer suitable to the music genre. (Select [ use the settings made in [

bass boost level.;

FUNCTION

AUDIO CONTROL

): Adjusts the subwoofer output level.

–9

to +9 (0):(Refer to

:Turns on the extended bass.;

BAND1 LEVEL

:Adjust the quality factor.

MANUAL EQ

OFF

:Cancels.

], then press the

BAND2 LEVEL

].)

:Selects your preferred

Default:

below.)

OFF

:Cancels.

BAND13 LEVEL

USER

: ] to

ENGLISH

AUDIO SETTINGS

LOUDNESS LEVEL1/ LEVEL2

SUBWOOFER SET ON

FADER R15

BALANCE L15

VOLUME OFFSET –15

SOUND EFFECT

SOUND RECNSTR

(Sound reconstruction)

SPACE ENHANCE

SND REALIZER LEVEL1/ LEVEL2/ LEVEL3

STAGE EQ LOW/ MIDDLE/ HIGH

DRIVE EQ ON

frequencies boost to produce a well-balanced sound at a low volume level.;

:Turns on the subwoofer output.;

balance.

(Before adjustment, select the source you want to adjust.)

(Not applicable for TUNER source, AUX source and SIRIUS XM source.)

:Creates realistic sound by compensating the highfrequency components and restoring the rise-time of the waveform that are lost in audio data compression.;

OFF

:Cancels.

(Not applicable for TUNER source.)

SMALL/ MEDIUM/ LARGE

space.;

realistic.;

heard from the speakers.;

: Boosts the frequency to reduce the noise heard from outside the car or running noise of the tyres.;

:Selects your preferred low and high

OFF

:Cancels.

F15 (0

):Adjusts the rear and front speaker output

R15 (0

):Adjusts the left and right speaker output

to +6 (0):Preset the initial volume level of each source.

OFF

:Cancels.

OFF

:Cancels.

OFF

:Cancels.

:Virtually enhances the sound

:Virtually makes the sound more

:Virtually adjust the sound position

OFF

:Cancels.

OFF

:Cancels.

SPEAKER SIZE

FRONT SIZE

TWEETER SMALL/ MIDDLE/ LARGE

REAR 3.5"/ 4"/ 4.75"/ 5"/ 6.5"/ 6.75"/ 7"/ 4×6/ 5×7/ 6×8/ 6×9/ 7×10

SUBWOOFER 6.5"/ 8"/ 10"/ 12"/ 15" OVER

X ' OVER

TWEETER FRQ

FRONT HPF F - HPF FRQ 30HZ/ 40HZ/ 50HZ/ 60HZ/ 70HZ/ 80HZ/ 90HZ

Selects according to the connected speaker size for optimum performance.;

NONE

:Not connected.

size for optimum performance.;

GAIN LEFT

GAIN RIGHT –8

F - HPF SLOPE –6DB/ –12DB/ –18DB/ –24DB: Adjusts the

F - HPF GAIN –8

3.5"/ 4"/ 4.75"/ 5"/ 6.5"/ 6.75"/ 7"/ 4×6/ 5×7/ 6×8

6×9/ 7×10

speaker size for optimum performance.

size range of the connected tweeter for optimum performance.;

1KHZ/ 1.6KHZ/ 2.5KHZ/ 4KHZ/ 5KHZ/ 6.3KHZ/ 8KHZ

10KHZ/ 12.5KHZ: Adjusts the crossover

frequency for the tweeter speaker.

–8

to 0:Adjusts the output volume of the left tweeter.

to 0:Adjusts the output volume of the right tweeter.

100HZ/ 120HZ/ 150HZ/ 180HZ/ 220HZ/ 250HZ: Adjusts the crossover frequency for the selected speakers (high pass filter). sent to the selected speakers.

crossover slope. [

THROUGH

to 0:Adjusts the output volume of the selected

speaker.

: Selects according to the connected

:Selects according to the

NONE

:Not connected.

: Selects according to the connected speaker

NONE

:Not connected.

;

THROUGH

: All signals are

(Selectable only if a setting other than

] is selected for [

F - HPF FRQ

].)

AUDIO SETTINGS

REAR HPF R - HPF FRQ

R - HPF SLOPE

R - HPF GAIN

SUBWOOFER LPF SW LPF FRQ

SW LPF SLOPE –6DB/ –12DB/ –18DB/ –24DB: Adjusts the

SW LPF PHASE REVERSE

SW LPF GAIN –8

•

[

SUB-W LEVEL

selectable only if [

• [TWEETER], [REAR HPF]

other than

SIZE]

•

Once you have selected the speaker size (

settings are automatically set for the crossover of the selected speaker.

( 22)

]/ [

[NONE]

SUBWOOFER

SUBWOOFER SET

and

is selected for

(Refer

FRONT HPF, 22.)

30HZ/ 40HZ/ 50HZ/ 60HZ/ 70HZ/ 80HZ/ 90HZ/ 100HZ

120HZ/ 150HZ/ 180HZ/ 220HZ/ 250HZ

Adjusts the crossover frequency for the subwoofer (low pass filter).; the subwoofer.

crossover slope. than [

of the subwoofer output to be in line with the speaker output for optimum performance.

to 0:Adjusts the output volume of the

subwoofer.

] of [

SPEAKER SIZE

] is set to [ON].

[SUBWOOFER LPF]

[TWEETER], [REAR]

[SPEAKER SIZE], 22

THROUGH

(Selectable only if a setting other

THROUGH

] is selected for [

(180°)/

NORMAL

]/ [

SUBWOOFER LPF

( 22)

[X ‘ OVER]

and

: All signals are sent to

SW LPF FRQ

(0°): Selects the phase

] of [

is selectable only if a setting

[SUBWOOFER]

[SPEAKER

), the frequency and slope

X ‘ OVER

DISPLAY SETTINGS

ZONE 1

ZONE 2

Set the dimmer

].)

Press and hold DISP (DIM) to turn on or off the dimmer.

• If you have set [ and hold this button.

DIMMER TIME

Other settings

Press the volume knob to enter [

1 2 Turn the volume knob to select [

] is

3 Turn the volume knob to select an item (  4 Repeat step 3 until the desired item is selected/activated or follow

the instructions stated on the selected item.

5 Press and hold to exit.

To return to the previous setting item, press .

ALL ZONE

] ( 24), it will be canceled once you press

FUNCTION

DISPLAY

], then press the knob.

), then press the knob.

ENGLISH

DISPLAY SETTINGS

COLOR SELECT VARIABLE SCAN/ CUSTOM R/G/B

DIMMER

BRIGHTNESS

TEXT SCROLL AUTO/ ONCE

Preset colors:

BLUE2 GREEN2 ORANGERED

color for button illumination and display illumination. To make your own color, select [

made will be stored in [

Press the volume knob to enter the detailed color adjustment.

Press S/T to select the color (R/ G/ B) to adjust.

Turn the volume knob to adjust the level (0 — 9), then press the knob.

Dim the display illumination and button illumination.

:Dimmer is turned on.;

DIMMER TIME

Turn the volume knob to adjust the [ON] time, then press the knob.

Turn the volume knob to adjust the [

(Default: [

Select a zone for setting.

0 — 31: Selects your preferred brightness level for display illumination

automatically, or scroll only once.;

RED1/ RED2/ RED3/ PURPLE1/ PURPLE2/ PURPLE3/ PURPLE4/ BLUE1/

BLUE3/ SKYBLUE1/ SKYBLUE2/ LIGHTBLUE/ AQUA1/ AQUA2/ GREEN1/

GREEN3/ YELLOWGREEN1/ YELLOWGREEN2/ YELLOW/ ORANGE1/ ORANGE2/

:Set the dimmer on and off time.

6:00 PM

and button illumination.

:Selects whether to scroll the display information

/ preset colors*: Selects your preferred

CUSTOM R/G/B

OFF

; [

OFF

:Cancels.

6:00 AM

( 23)

OFF

] time, then press the knob.

)

OFF

:Cancels.

]. The color you have

Default:

REFERENCES

Maintenance

Cleaning the unit

Wipe off dirt on the faceplate with a dry silicone or soft cloth.

Cleaning the connector

Detach the faceplate and clean the connector gently with a cotton swab, being careful not to damage the connector.

Connector (on the reverse

Handling discs

•

Do not touch the recording surface of the disc.

•

Do not stick tape etc. on the disc, or use a disc with tape stuck on it.

•

Do not use any accessories for the disc.

•

Clean from the center of the disc and move outward.

•

Clean the disc with a dry silicone or soft cloth. Do not use any solvents.

•

When removing discs from this unit, pull them out horizontally.

•

Remove burrs from the center hole and disc edge before inserting a disc.

More information

Visit also the following website <www.kenwood.com/cs/ce/> for:

–

Latest firmware updates and latest compatible item list

–

Android™ application KENWOOD MUSIC PLAY

–

Any other latest information

General

•

This unit can only play the following CDs:

•

Detailed information and notes about the playable audio files are stated in an online manual

on the following website: www.kenwood.com/cs/ce/audiofile/

side of the faceplate)

REFERENCES

Playable files

•

Playable audio file: MP3 (.mp3), WMA (.wma), AAC (.aac)

•

Playable disc media: CD-R/CD-RW/CD-ROM

•

Playable disc file format: ISO 9660 Level 1/2, Joliet, Long file name.

•

Playable USB device file system: FAT12, FAT16, FAT32 Even when audio files comply with the standards listed above, playback may be impossible depending on the types or conditions of media or device. The AAC (.m4a) file in a USB device or a CD encoded by iTunes cannot be played on this unit.

Unplayable discs

•

Discs that are not round.

•

Discs with coloring on the recording surface or discs that are dirty.

•

Recordable/ReWritable discs that have not been finalized.

•

8cm CD. Attempting to insert using an adapter may cause malfunction.

About USB devices

•

This unit can play MP3/WMA/AAC/WAV/FLAC files stored on a USB mass storage class device.

•

You cannot connect a USB device via a USB hub.

•

Connecting a cable whose total length is longer than 5m may result in abnormal playback.

•

This unit cannot recognize a USB device whose rating is other than 5V and exceeds 1.5A.

About iPod/iPhone

Made for

iPod touch (2nd, 3rd, 4th, and 5th generation)

iPod classic

iPod nano (3rd, 4th, 5th, 6th, and 7th generation)

iPhone 3G, 3GS, 4, 4S, 5, 5S, 5C, 6, 6 Plus

•

You cannot operate iPod if “KENWOOD” or “ ” is displayed on iPod.

•

Depending on the version of the operating system of the iPod/iPhone, some functions may

not operate on this unit.

About Android device

•

This unit supports Android OS 4.1 and above.

•

Some Android devices (with OS 4.1 and above) may not fully support Android Open Accessory

(AOA) 2.0.

•

If the Android device supports both mass storage class device and AOA 2.0, this unit always

playback via AOA 2.0 as priority.

About Pandora

•

Pandora is only available in certain countries.

Please visit <http://www.pandora.com/legal> for more information.

•

Because Pandora is a third-party service, the specifications are subject to change without

prior notice. Accordingly, compatibility may be impaired, or some or all of the services may become unavailable.

•

Some functions of Pandora cannot be operated from this unit.

•

For issues using the application, please contact Pandora at pandora-support@pandora.com.

About iHeartRadio

•

iHeartRadio® is a third-party service, therefore the specifications are subject to change

without prior notice. Accordingly, compatibility may be impaired or some or all of the services may become unavailable.

•

Some iHeartRadio® functionality cannot be operated from this unit.

About Bluetooth

•

Depending on the Bluetooth version of the device, some Bluetooth devices may not be able

to connect to this unit.

•

This unit may not work with some Bluetooth devices.

•

Signal conditions vary, depending on the surroundings.

•

Compatible remote device for NFC function:

Remote devices with a NFC function (OS: Android™ 2.3.3 or later, excluding Android 3.x). If the OS version of your remote device is older than Android 4.1.x, download and start the “NFC Easy Connect” application. (“NFC Easy Connect” is a free application available at Google Play.)

ENGLISH

REFERENCES

About HD Radio™ Technology

Change the display information

Each time you press

•

If the information is unavailable or not recorded,

(eg. station name, playing time) appears.

Source name Display information

STANDBY

HD RADIO

CD or USB

•

Adjacent to traditional main stations are HD2/HD3 Channels, providing

new original programming on the FM dial.

•

HD Radio broadcasts deliver crystal clear, CD-like digital audio quality to

consumers; eliminates background noise.

•

Program Info provides song name, artist, station ID, and other relevant

data to enrich the listening experience.

DISP

, the display information changes.

Source name (Date/Clock)*

Frequency (Date/Clock)*

(For digital stations only)

Station name (Date/Clock)* Song title (Artist) Song title (Album title)

Song title (Date/Clock)* Frequency (Date/Clock)*

(back to the beginning)

(For FM Radio Broadcast Data System stations only)

Station name (Date/Clock)* Radio text (Date/Clock)* Radio text+ (R.TEXT+)

(For CD-DA)

Track title (Artist) Track title (Disc name) Track title (Date/Clock)* Playing time (Date/Clock)*

(For MP3/WMA/AAC/WAV/FLAC files)

Track title (Artist) Track title (Album title) Track title (Date/Clock)* File name (Folder name) (Date/Clock)*

Title (Artist) Title (Date/Clock)* Frequency (Date/Clock)*

(back to the beginning)

“NO TEXT”, “NO INFO”, or other information

(back to the beginning)

File name (Date/Clock)* Playing time

Source name Display information

iPod or ANDROID

PANDORA

IHEARTRADIO

SIRIUS XM Channel number (Status) Channel name (Status) Artist name

BT AUDIO

AUX

Battery and signal strength of the Bluetooth device will be shown if [

[

AUTO

]. ( 17)

Track title (Artist) Track title (Album name) Track title (Date/Clock)*

Playing time (Date/Clock)* (back to the beginning)

Station name (Date/Clock)* Shared / Radio station (Date/Clock)* Track title (Artist) Playing time (Date/Clock)*

Station name (Date/Clock)* Track title (Artist) Track title (Date/Clock)*

(Status) Category name (Status)

Track title (Artist) Track title (Album name) Track title (Date/Clock)*

Playing time (Date/Clock)* (back to the beginning)

Source name (Date/Clock)*

Track title (Album title) Track title (Date/Clock)*

(back to the beginning)

Song title (Status) Content information (Status)

Clock (Status)

(back to the beginning)

BATT/SIGNAL

] is set to

+ 74 hidden pages