KDC-X799
KDC-BT762HD
CD-RECEIVER
INSTRUCTION MANUAL
AMPLI-TUNER LECTEUR DE CD
MODE D’EMPLOI
REPRODUCTOR DE DISCOS COMPACTOS RECEPTOR DE FM/AM
MANUAL DE INSTRUCCIONES
Take the time to read through this instruction manual.
Familiarity with installation and operation procedures will help you obtain the best performance from your new CD-receiver.
For your records
Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below. Refer to the model and serial numbers whenever you call upon your Kenwood dealer for information or service on the product.
Model KDC-X799/ KDC-BT762HD Serial number
US Residents Only
Register Online
Register your Kenwood product at www.Kenwoodusa.com
© 2014 JVC KENWOOD Corporation |
B5A-0149-00 (KW) |
CAUTION
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
In compliance with Federal Regulations, following are reproductions of labels on, or inside the product relating to laser product safety.
JVC KENWOOD Corporation
2967-3, ISHIKAWA-MACHI,
HACHIOJI-SHI, TOKYO, JAPAN
THIS PRODUCT COMPLIES WITH DHHS RULES 21CFR SUBCHAPTER J IN EFFECT AT DATE OF MANUFACTURE.
Location : Top Plate
FCC WARNING
This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.
FCC NOTE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment may cause harmful interference to radio communications, if it is not installed and used in accordance with the instructions. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
Información acerca de la eliminación de equipos eléctricos y electrónicos al final de la vida útil (aplicable a los países que hayan adoptado sistemas independientes de recogida de residuos)
Los productos con el símbolo de un contenedor con ruedas tachado no podrán ser desechados como residuos domésticos. Los equipos eléctricos y electrónicos al final de la vida útil, deberán ser reciclados en instalaciones que puedan dar el tratamiento adecuado a estos productos y a sus subproductos residuales correspondientes. Póngase en contacto con su administración local para obtener información sobre el punto de recogida más cercano. Un tratamiento correcto del reciclaje y la eliminación de residuos ayuda a conservar los recursos y evita al mismo tiempo efectos perjudiciales en la salud y el medio ambiente.
Informação sobre a eliminação de pilhas
Este produto não deve ser eliminado como lixo doméstico geral. Devolva a pilha usada ao revendedor ou entidade autorizada para que a mesma seja devolvida ao fabricante ou importador.
A reciclagem e a eliminação de lixo de maneira apropriada ajudarão a conservar os recursos naturais ao mesmo tempo que prevenirão os efeitos prejudicais à nossa saúde e ao meio ambiente.
CALIFORNIA, USA ONLY
This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material— special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate
i
IC (Industry Canada) Notice
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1)This device may not cause interference, and
(2)this device must accept any interference, including interference that may cause undesired operation of the device.
The term “IC: ” before the certification/ registration number only signifies that the Industry Canada technical specification were met.
Note de IC (Industrie Canada)
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes:
(1)l’appareil ne doit pas produire de brouillage, et
(2)l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
L’expression “IC:” avant le numéro d’homologation/ enregistrement signifie seulement que les specifications techniques d’Industrie Canada ont été respectées.
Para cumplimiento de la COFETEL:
“La operación de este equipo está sujeta a las siguientes dos condiciones:
(1)es posible que este equipo o dispositivo no cause interferencia perjudicial y
(2)este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operación no deseada”
CAUTION
This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that it deemed to comply without maximum permissive exposure evaluation (MPE). But it is desirable that it should be installed and operated keeping the radiator at least 20cm or more away from person’s body (excluding extremities: hands, wrists, feet and ankles).
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
ATTENTION
Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un environnement non contrôlé et respecte les règles d’exposition aux fréquences
radioélectriques (RF) CNR-102 de l’IC. Cet équipement émet une énergie RF très faible qui est considérée conforme sans évaluation de l’exposition maximale autorisée. Cependant, cet équipement doit être installé et utilisé en gardant une distance de 20 cm ou plus entre le dispositif rayonnant et le corps (à l’exception des extrémités : mains, poignets, pieds et chevilles).
Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d’un type et d’un gain maximal (ou inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une communication satisfaisante.
ii
CONTENTS
|
BEFORE USE |
2 |
|
|
BASICS |
3 |
|
|
GETTING STARTED |
4 |
|
|
HD Radio™ tuner |
5 |
|
|
CD / USB / iPod / ANDROID |
6 |
|
|
Pandora® |
8 |
|
|
iHeartRadio® |
9 |
|
|
SiriusXM® Radio |
10 |
|
|
AUX |
12 |
|
|
BLUETOOTH® |
13 |
|
|
AUDIO SETTINGS |
19 |
|
|
DISPLAY SETTINGS |
20 |
|
|
MORE INFORMATION |
21 |
|
|
TROUBLESHOOTING |
22 |
|
|
SPECIFICATIONS |
24 |
|
|
INSTALLATION / |
|
|
|
CONNECTION |
26 |
|
|
|
|
|
How to read this manual
•Operations are explained mainly using buttons on the faceplate.
•[XX] indicates the selected items.
•( XX) indicates references are available on the stated page.
BEFORE USE
Warning
Do not operate any function that takes your attention away from safe driving.
Caution
Volume setting:
•Adjust the volume so that you can hear sounds outside the car to prevent accidents.
•Lower the volume before playing digital sources to avoid damaging the speakers by the sudden increase of the output level.
General:
•Avoid using the external device if it might hinder safe driving.
•Make sure all important data has been backed up. We shall bear no responsibility for any loss of recorded data.
•Never put or leave any metallic objects (such as coins or metal tools) inside the unit, to prevent a short circuit.
•If a disc error occurs due to condensation on the laser lens, eject the disc and wait for the moisture to evaporate.
Remote control (RC-406):
•Do not leave the remote control in hot places such as on the dashboard.
•The Lithium battery is in danger of explosion if replaced incorrectly. Replace it only with the same or equivalent type.
•The battery pack or batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
•Keep the battery out of reach of children and in its original packaging when not in used. Dispose of used batteries promptly. If swallowed, contact a physician immediately.
Maintenance
Cleaning the unit: Wipe off dirt on the faceplate with a dry silicone or soft cloth.
Cleaning the connector: Detach the faceplate and clean the connector gently with a cotton swab, being careful not to damage the connector.
Handling discs:
•Do not touch the recording surface of the disc.
•Do not stick tape etc. on the disc, or use a disc with tape stuck on it.
•Do not use any accessories for the disc.
•Clean from the center of the disc and move outward.
•Clean the disc with a dry silicone or soft cloth. Do not use any solvents.
•When removing discs from this unit, pull them out horizontally.
•Remove burrs from the center hole and disc edge before inserting a disc.
Connector (on the reverse side of the faceplate)
2
BASICS
Faceplate
Volume knob |
|
(turn/press) |
Display window |
Detach button
Attach |
Detach |
How to reset |
Your preset adjustments will also be erased.
Remote control (RC-406)
Remote sensor (Do not expose to bright sunlight.)
Pull out the insulation
sheet when using for
the first time.
How to replace the battery |
To |
On the faceplate |
On the remote control |
|
||
Turn on the power |
Press |
. |
Press and hold SRC to turn off the power. |
||
|
• Press and hold to turn off the power. |
( Pressing SRC does not turn on the power. ) |
|||
|
|
|
|
|
|
Adjust the volume |
Turn the volume knob. |
Press |
or |
. |
|
|
|
|
|
||
|
|
|
Press ATT during playback to attenuate the sound. |
||
|
|
|
• Press again to cancel. |
|
|
Select a source |
Press |
repeatedly. |
Press SRC repeatedly. |
|
|
|
|
|
|
|
|
Change the display |
Press |
repeatedly. |
( not available ) |
|
|
information |
• Press and hold to scroll the current display information. |
|
|||
|
|
|
ENGLISH 3
GETTING STARTED
1Cancel the demonstration
When you turn on the power (or after you reset the unit), the display shows: “CANCEL DEMO” “PRESS”
“VOLUME KNOB”
1Press the volume knob.
[YES] is selected for the initial setup.
2Press the volume knob again.
“DEMO OFF” appears.
2Set the clock
1 Press the volume knob to enter [FUNCTION].
2 Turn the volume knob to select [CLOCK], then press the knob.
3 Turn the volume knob to select [CLOCK ADJUST], then press the knob.
4Turn the volume knob to make the settings, then press the knob.
Day Hour
Minute
5 Turn the volume knob to select [CLOCK FORMAT], then press the knob. 6 Turn the volume knob to select [12H] or [24H], then press the knob. 7 Press and hold to exit.
To return to the previous setting item, press .
3Set the initial settings
1 Press to enter STANDBY.
2 Press the volume knob to enter [FUNCTION].
3Turn the volume knob to make a selection (see the following table), then press the knob.
4 Repeat step 3 until the desired item is selected or activated. 5 Press and hold to exit.
To return to the previous setting item, press .
|
|
|
|
Default: XX |
AUDIO CONTROL |
|
|||
|
SP SELECT |
OFF/ 5/4/ 6 × 9/6/ OEM: Selects according to the speaker size (5 inches |
||
|
|
|
|
or 4 inches, 6×9 inches or 6 inches) or OEM speakers for optimum |
|
|
|
|
performance. |
DISPLAY |
|
|||
|
EASY MENU |
ON: Both display and button illumination change to white color when |
||
|
|
|
|
entering [FUNCTION]. ; OFF: Both display and button illumination |
|
|
|
|
remain as [COLOR SELECT] color. ( 20) |
TUNER SETTING |
|
|||
|
PRESET TYPE |
NORMAL: Memorizes one station for each preset button in each band |
||
|
|
|
|
(FM1/ FM2/ FM3/ AM). ; MIX: Memorizes one station or SiriusXM channel |
|
|
|
|
for each preset button, regardless of the selected band or SiriusXM |
|
|
|
|
channel. |
SYSTEM |
|
|||
|
KEY BEEP |
ON: Activates the keypress tone. ; OFF: Deactivates. |
||
|
SOURCE SELECT |
|
||
|
|
PANDORA SRC |
ON: Enables PANDORA in source selection. ; OFF: Disables. ( 8) |
|
|
|
IHEART SRC |
ON: Enables IHEARTRADIO in source selection. ; OFF: Disables. ( 9) |
|
|
|
BUILT-IN AUX |
ON: Enables AUX in source selection. ; OFF: Disables. ( 12) |
|
|
CD READ |
1: Automatically distinguishes between audio file disc and music CD. ; |
||
|
|
|
|
2: Forces to play as a music CD. No sound can be heard if an audio file |
|
|
|
|
disc is played. |
|
F/W UPDATE |
|
||
|
|
UPDATE SYSTEM / UPDATE BT / UPDATE HD |
||
|
|
|
F/W UP xx.xx/ |
YES: Starts upgrading the firmware. ; NO: Cancels (upgrading is not |
|
|
|
F/W UP Vxx |
activated). |
|
|
|
|
For details on how to update the firmware, see: |
|
|
|
|
www.kenwood.com/cs/ce/ |
CLOCK |
|
|||
|
CLOCK DISPLAY |
ON: The clock time is shown on the display even when the unit is turned |
||
|
|
|
|
off. ; OFF: Cancels. |
4
HD Radio™ tuner
You can tune in to both conventional and HD Radio broadcasts.
•To find HD Radio stations in your area, visit <http://www.hdradio.com>.
Search for a station
1 Press repeatedly to select HD RADIO.
2Press repeatedly (or press
/
on RC-406) to select FM1/ FM2/ FM3/ AM.
3Press S/ T(or press S/ on RC-406) to search for a station or channel.
•To change the searching method for S/ T: Press repeatedly.
AUTO1 : Automatically search for a station or channel. AUTO2 : Search for a preset station or channel. MANUAL : Manually search for a station or channel.
•To store a station or channel: Press and hold one of the number buttons (1 to 6).
•To select a stored station or channel: Press one of the number buttons (1 to 6) (or press one of the number buttons (1 to 6) on RC-406).
Direct Access Tuning (using RC-406)
1 Press DIRECT to enter Direct Access Tuning.
2 Press the number buttons to enter a frequency.
3 Press to search for a station or channel.
•To cancel, press or DIRECT.
•If no operation is done for 10 seconds after step 2, Direct Access Tuning is automatically canceled.
Select an HD Radio multicast channel
Many HD Radio stations offer more than one channel programming.
This service is called multicasting. While receiving HD Radio multicast channels....
Press S/ Tto select your desired channel (HD1 to HD8).
“LINKING” appears while linking to a multicast channel.
Other settings
1 Press the volume knob to enter [FUNCTION].
2Turn the volume knob to make a selection (see the following table), then press the knob.
3 Repeat step 2 until the desired item is selected or activated. 4 Press and hold to exit.
To return to the previous setting item, press .
|
|
Default: XX |
TUNER SETTING |
|
|
|
|
|
|
IF BAND |
AUTO: Increases the tuner selectivity to reduce interference noises from adjacent |
|
|
FM stations. (Stereo effect may be lost.) ; WIDE: Subjects to interference noises from |
|
|
adjacent FM stations, but sound quality will not be degraded and the stereo effect |
|
|
will remain. |
|
AUTO |
YES: Automatically starts memorizing 6 stations with good reception. ; NO: Cancels. |
|
MEMORY |
• Selectable only if [NORMAL] is selected for [PRESET TYPE]. ( 4) |
|
|
|
|
RECEIVE |
Sets the receive mode of the HD Radio receiver. |
|
MODE |
AUTO: Automatically tunes to analog broadcast when there is no digital broadcast. ; |
|
|
DIGITAL: Tunes in to digital broadcast only. ; ANALOG: Tunes in to analog broadcast |
|
|
only. |
|
|
|
CLOCK |
|
|
|
TIME SYNC |
ON: Synchronizes the unit’s time to the Radio Broadcast Data System station time. ; |
|
|
OFF: Cancels. |
ENGLISH |
5 |
CD / USB / iPod / ANDROID
Start playback
The source changes automatically and playback starts.
|
|
|
|
Label side |
M Eject disc |
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
USB input terminal
USB
CA-U1EX (max.: 500 mA) (optional accessory)
iPod/iPhone
KCA-iP102 / KCA-iP103 (optional accessory)*1 or accessory cable of the iPod/iPhone*2
ANDROID*3
Micro USB 2.0 cable*2 (commercially available)
*1 KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type *2 Do not leave the cable inside the car when not
using.
To |
On the faceplate |
|
|
On the remote control |
|
|||
Playback / pause |
Press |
. |
|
|
Press |
|
. |
|
Reverse / Fast-forward*4 |
Press and hold S / T. |
|
Press and hold S / |
. |
||||
Select a track/file |
Press S / T. |
|
|
Press S / |
|
. |
|
|
|
|
|
|
|
|
|
|
|
Select a folder*5 |
Press J / K. |
|
|
Press |
/ |
. |
|
|
Repeat play*6 |
Press |
repeatedly. |
|
|
|
|
|
|
|
TRACK REPEAT/ REPEAT OFF |
|
: Audio CD |
|
|
|
||
|
FILE REPEAT/ FOLDER REPEAT/ REPEAT OFF : MP3/WMA/AAC/WAV file, iPod or |
|||||||
|
|
|
|
|
ANDROID |
|
|
|
|
FILE REPEAT/ REPEAT OFF |
|
: KME Light/ KMC file*7 |
|
||||
Random play*6 |
Press |
repeatedly. |
|
|
|
|
|
|
|
DISC RANDOM/ RANDOM OFF |
: Audio CD |
|
|
|
|||
|
FOLDER RANDOM/ RANDOM OFF : MP3/WMA/AAC/WAV file, KME Light/ KMC |
|||||||
|
|
|
|
file, iPod or ANDROID |
|
|
||
|
|
|
|
|
|
|||
|
Press and hold |
to select ALL RANDOM.*8 |
|
|
|
|||
Select control mode |
While in iPod source, press |
repeatedly. |
|
|
|
|||
|
MODE ON : Control from the iPod*9 |
|
|
|
||||
|
MODE OFF : Control from the unit |
|
|
|
While in ANDROID source, (7, [ANDROID SETUP])
Select music drive |
Press |
repeatedly. |
|
( 7, [MUSIC DRIVE]) |
The stored songs in the following start playback. |
||
|
• |
Selected internal or external memory of a smartphone (Mass Storage |
|
|
|
Class). |
|
|
• |
Selected drive of a multiple drives device. |
|
|
|
|
|
6
CD / USB / iPod / ANDROID
*3 |
When connecting an Android device, “Press [VIEW] to install KENWOOD MUSIC PLAY APP” is |
|
|
shown. Follow the instructions to install the application. You can also install the latest version |
|
*4 |
of KENWOOD MUSIC PLAY application on your Android device before connecting. ( 21) |
|
For ANDROID: Applicable only when [BROWSE MODE] is selected. ( [ANDROID SETUP]) |
||
*5 |
For CD: Only for MP3/WMA/AAC files. This does not work for iPod/ ANDROID. |
|
*6 |
For iPod/ ANDROID: Applicable only when [MODE OFF]/ [BROWSE MODE] is selected. |
|
*7 |
KME Light : KENWOOD Music Editor Light, KMC : KENWOOD Music Control ( 21) |
|
*8 |
For CD: Only for MP3/WMA/AAC files. |
|
*9 |
You can still play/pause, file skip, fast-forward or reverse files from the unit. |
|
|
||
Select a file from a folder/list |
||
1 |
Press |
. |
2 |
Turn the volume knob to select a folder/list, then press the knob. |
|
3 |
Turn the volume knob to select a file, then press the knob. |
Quick Search
If you have many files, you can search through them quickly.
For USB (for KME Light/ KMC files):
Press S / T to search at a preset skip search ratio. ([SKIP SEARCH]) Press and hold S / T to search at a 10% ratio.
• Not applicable for CD and MP3/WMA/AAC/WAV files.
For iPod:
You can search for a file according to the first character.
Turn the volume knob quickly to enter character search.
Turn the volume knob to select the character.
To search for a character other than A to Z and 0 to 9, enter only “*”. Press S / T to move to the entry position.
• You can enter up to 3 characters.
Press the volume knob to start searching.
•To return to the root folder/ first file/ top menu, press .
•To return to the previous setting item, press .
•To cancel, press and hold .
•For iPod, applicable only when [MODE OFF] is selected. ( 6)
•For ANDROID, applicable only when [BROWSE MODE] is selected. ( [ANDROID SETUP])
Direct Music Search (using RC-406)
1 Press DIRECT.
2 Press the number buttons to enter a track/file number.
3Press to search for music.
•To cancel, press or DIRECT.
•Not available if Random Play is selected.
•Not applicable for iPod, ANDROID, KME Light/ KMC file.
Listen to TuneIn Radio/ TuneIn Radio Pro/ Aupeo
While listening to TuneIn Radio, TuneIn Radio Pro or Aupeo, connect the iPod/iPhone to the USB input terminal of the unit.
• The unit will output the sound from these applications.
Other settings
1 Press the volume knob to enter [FUNCTION].
2Turn the volume knob to make a selection (see the following table), then press the knob.
3 Repeat step 2 until the desired item is selected or activated. 4 Press and hold to exit.
To return to the previous setting item, press .
Default: XX
ANDROID SETUP
BROWSE MODE: Control from the unit (using KENWOOD MUSIC PLAY application). ; HAND MODE: Control other media player applications from the Android device (without using KENWOOD MUSIC PLAY application). However, you can still play/pause and file skip from the unit.
USB
|
MUSIC DRIVE |
DRIVE CHANGE: The next drive ([DRIVE 1] to [DRIVE 5]) is selected |
|
|
automatically and playback starts. |
|
|
Repeat steps 1 to 3 to select the following drives. |
|
SKIP SEARCH |
0.5%/ 1%/ 5%/ 10%: While listening to iPod, ANDROID or KME |
|
|
Light/ KMC file, selects the skip search ratio over the total files. |
ENGLISH 7
Pandora®
Preparation:
Install the latest version of the Pandora application on your device (iPhone/ iPod touch), then create an account and log in to Pandora.
• Select [ON] for [PANDORA SRC]. ( 4)
Start listening
1 Open the Pandora application on your device.
2 Connect your device to the USB input terminal.
USB input terminal
KCA-iP102 / KCA-iP103 (optional accessory)*1 or accessory cable of the iPod/iPhone*2
The source changes to PANDORA and broadcast starts.
To |
|
On the faceplate |
|
On the remote control |
|
||
Playback / pause |
Press |
. |
|
Press |
. |
|
|
|
|
|
|
|
|
|
|
Skip a track |
Press T. |
|
|
Press |
. |
|
|
|
|
|
|
|
|
|
|
Thumbs up or thumbs |
Press |
/ |
. |
Press |
/ |
. |
|
down*3 |
|
|
|
|
|
|
|
*1 |
KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type |
|
|
|
|
||
*2 |
Do not leave the cable inside the car when not using. |
|
|
|
|
||
*3 |
If thumbs down is selected, the current track is skipped. |
|
|
|
Create and save a new station
1 Press and hold the volume knob.
2Turn the volume knob to select [FROM TRACK] or [FROM ARTIST], then press the knob.
A new station is created based on the current song or artist.
3 Press and hold one of the number buttons (1 to 5) to store.
To select a stored station, press one of the number buttons (1 to 5).
Search for a registered station
1 Press |
. |
2Turn the volume knob to make a selection, then press the knob.
[BY DATE]: According to the registered date [A-Z]: Alphabetical order
3 Turn the volume knob to the desired station, then press the knob.
To cancel, press and hold . (or using RC-406)
Press J/ K to search for a station, then press .
Bookmark a song or artist information
1 Press and hold J.
2Turn the volume knob to make a selection, then press the knob.
[THIS TRACK]: Current song information [THIS ARTIST]: Current artist information
“BOOKMARKED” appears and the information is stored to your device. The bookmark is available on your Pandora account but not on this unit.
8
iHeartRadio®
Preparation:
Install the latest version of iHeart Link for KENWOOD application on your device (iPhone/ iPod touch), then create an account and log in to iHeartRadio.
• Select [ON] for [IHEART SRC]. ( 4)
Start listening
1 Open the iHeart Link application on your device.
2 Connect your device to the USB input terminal.
USB input terminal
KCA-iP102 / KCA-iP103 (optional accessory)*1 or accessory cable of the iPod/iPhone*2
3Press repeatedly to select IHEARTRADIO.
Broadcast starts automatically.
To |
|
On the faceplate |
|
On the remote control |
||
Playback / pause |
Press |
. |
|
Press |
. |
|
|
|
|
|
|
|
|
Skip a track for custom station |
Press T. |
|
|
Press |
. |
|
|
|
|
|
|
|
|
Thumbs up or thumbs down*3 |
Press |
/ |
. |
|
— |
|
for custom station |
|
|
|
|
||
|
|
|
|
|
||
Create a new/custom station |
Press 1. |
|
|
|
— |
|
|
|
|
|
|
|
|
Add to favorite stations for live |
Press 2. |
|
|
|
— |
|
station |
|
|
|
|
||
|
|
|
|
|
||
|
|
|
|
|
|
|
Scan for live station |
Press 5. |
|
|
|
— |
|
|
|
|
|
|
|
|
*1 |
KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type |
|
|
|
|
|
*2 |
Do not leave the cable inside the car when not using. |
|
|
|
|
|
*3 |
If thumbs down is selected, the current track is skipped. |
|
|
|
|
Search for a station
1 Press |
. |
2Turn the volume knob to select a category, then press the knob.
3Turn the volume knob to the desired station, then press the knob.
When a city list appears, you can skip cities in alphabetical order.
To cancel, press and hold . (or using RC-406)
Press J/ K to search for a station, then press .
Skip cities by alphabetical order
While a city list appears during search...
1 Turn the volume knob quickly to enter character search.
2Turn the volume knob or press S / T to select the character to be searched for.
3 Press J/ K to move to the previous/next page.
4 Press the volume knob to start searching.
To cancel, press and hold .
Delete a station
While listening to IHEARTRADIO...
1 Press the volume knob to enter [FUNCTION].
2 Turn the volume knob to select [SYSTEM], then press the knob.
3Turn the volume knob to select [STATION DEL], then press the knob.
4Turn the volume knob to select [LIVE] or [CUSTOM], then press the knob.
5Turn the volume knob to select the desired station to delete, then press the knob.
6 Turn the volume knob to select [YES], then press the knob. 7 Press and hold to exit.
To return to the previous setting item, press .
ENGLISH 9
SiriusXM® Radio
Only SiriusXM® brings you more of what you love to listen to, all in one place. Get over 140 channels, including commercial-free music plus the best sports, news, talk, comedy and entertainment. Welcome to the world of satellite radio. A SiriusXM Vehicle Tuner and Subscription are required. For more information, visit www.siriusxm.com.
Preparation:
1Connect the optional SiriusXM Vehicle Tuner (commercially available).
Antenna
Expansion port on |
SiriusXM Vehicle Tuner |
the rear panel |
|
2Check your Radio ID for activation.
The SiriusXM Radio ID is required for activation and can be found by tuning to Channel 0 as well as on the label found on the SiriusXM Connect tuner and its’ packaging.
The Radio ID does not include the letters I, O, S or F.
3Activate the subscription.
For users in U.S.A.:
Online: Go to www.siriusxm.com Phone: Call 1-866-635-2349
For users in Canada:
Online: Go to www.siriusxm.ca/activatexm Phone: Call 1-877-438-9677
4 Press repeatedly to select SIRIUS XM to start updating.
Start listening
1 Press repeatedly to select SIRIUS XM.
2 Press repeatedly to select a band.
3Press .
“” lights up.
4Turn the volume knob to select a category, then press the knob.
If “ALL CHANNELS” is selected, all the available channels will be shown.
5Turn the volume knob to select a channel, then press the knob. (or)
Press S / T to search for a channel manually.
• Pressing and holding S / T changes the channel rapidly.
If a locked channel or a mature channel is selected, a pass code input screen appears. Enter the pass code to receive the channel. ( 12)
To change the tuning method for S / T: Press .
Each time you press , the tuning method switches between “CHANNEL” (manually search for a channel) and “PRESET” (searches for a preset channel of the selected band).
Direct Access Tuning (using RC-406)
1 Press DIRECT to enter Direct Access Tuning.
2 Press the number buttons to enter a channel number.
3Press to start searching.
•To cancel, press or DIRECT.
•If no operation is done for 10 seconds after step 2, Direct Access Tuning is automatically canceled.
10
SiriusXM® Radio
SiriusXM Keymode
Press and hold to change the keymode (channel or replay). (Default: Channel keymode)
“” lights up when replay keymode is selected.
When channel keymode is selected...
To |
On the faceplate |
|
On the remote control |
||
Select a channel |
Press S / T. |
|
Press S / |
. |
|
|
|
|
|
||
Change a channel |
Press and hold S / T. |
|
Press and hold S / |
||
rapidly |
|
|
|
. |
|
|
|
|
|
|
|
Store a channel of |
Press and hold one of the |
|
— |
|
|
the current band |
number buttons (1 to 6). |
|
|
||
|
|
|
|||
|
|
|
|
|
|
Select a stored |
Press one of the number buttons (1 to 6). |
|
|||
channel of the |
|
|
|
|
|
current band |
|
|
|
|
|
|
|
|
|
||
When replay keymode is selected... |
|
|
|
||
To |
On the faceplate |
|
On the remote control |
||
|
|||||
Playback / pause |
Press |
. |
|
Press |
. |
|
|
|
|
|
|
Select a track |
Press S / T. |
|
Press S / |
. |
|
|
|
|
|
||
Rewind / |
Press and hold S / T. |
|
Press and hold S / |
||
Fast-forward |
|
|
|
. |
|
Go to Live |
Press 1. |
|
|
|
|
|
|
|
|
|
|
SmartFavorites and TuneStart™
User stored channels (1 to 6) of the current band are recognized as SmartFavorite channels. SiriusXM Vehicle Tuner automatically buffers the broadcast content in the background.
•SmartFavorites feature is available with SXV200 or later SiriusXM tuner models.
When you select a SmartFavorite channel, you can rewind and replay up to 30 minutes of any of the missed news, talk, sports or music content.
•Playback starts from the beginning of the song if [TUNE START] is set to [ON] ( 12) for most music channels stored as a SmartFavorite.
1 Press one of the number buttons (1 to 6) to select a channel.
2 For operation ( SiriusXM Keymode)
TuneScan™
You can get a short preview of the songs that you have missed on each of your SmartFavorite music channels or current tuned music channel.
Press and hold to start scanning the first 6 seconds of the recorded music contents.
•To listen to the current song, press the volume knob to stop scanning. The unit continues playing the current song.
•To select the previous/next song, press S / T.
•To cancel scanning, press and hold the volume knob. Playback returns to the channel before you enter TuneScan.
SiriusXM settings
1 Press the volume knob to enter [FUNCTION].
2 Turn the volume knob to select [SIRIUS XM], then press the knob.
3Turn the volume knob to make a selection ( 12), then press the knob.
4Repeat step 3 until the desired item is selected/activated or follow the instructions stated on the selected item.
5 Press and hold |
to exit. |
To return to the previous setting item, press .
ENGLISH 11
SiriusXM® Radio
|
|
|
|
|
Default: XX |
CHANNEL LOCK |
To unlock settings: |
|
|||
|
|
|
1 |
Turn the volume knob to select a number. |
|
|
|
|
2 |
Press S / T to move to the entry position. |
|
|
|
|
3 |
Repeat steps 1 and 2 to enter the current pass code. |
|
|
|
|
4 |
(Initial pass code is 0000.) |
|
|
|
|
Press the volume knob to confirm. |
||
|
|
|
|||
|
CODE SET |
1 Turn the volume knob to select a number. |
|||
|
|
|
2 |
Press S / T to move to the entry position. |
|
|
|
|
3 |
Repeat steps 1 and 2 to enter a new 4-digit pass code. |
|
|
|
|
4 |
Press the volume knob to confirm. |
|
|
|
|
5 |
Repeat steps 1 to 4 to reconfirm the pass code. |
|
|
|
|
• Make a note of the new pass code to enter channel lock settings |
||
|
|
|
|
from next time. |
|
|
LOCK SETTING |
MATURE CH: Selects the SiriusXM-defined lock setting. ; USER |
|||
|
|
|
DEFINED: Selects the user-defined lock setting. ; OFF: Cancels. |
||
|
CHANNEL EDIT*1 |
1 Turn the volume knob to select a category, then press the knob. |
|||
|
|
|
2 |
Turn the volume knob to select a channel you want to lock, then |
|
|
|
|
|
press the knob. |
|
|
|
|
3 |
“L” appears in front of the channel number. |
|
|
|
|
Press and hold |
to exit. |
|
|
|
|
|||
|
CHANNEL CLEAR*1 |
YES: Clears all the locked channels. ; NO: Cancels. |
|||
|
TUNE START*2 |
ON: Selected SmartFavorite channel starts playback from the |
|||
|
|
|
beginning of the song. ; OFF: Cancels. |
||
|
|
|
|||
|
SIGNAL LEVEL |
NO SIGNAL/ WEAK/ GOOD/ STRONG: Shows the strength of the |
|||
|
|
|
current received signal. |
|
|
|
|
|
|||
|
BUFFER USAGE |
0% — 100% (0): Shows the memory usage for Replay buffer. |
|||
|
|
|
|||
|
SXM RESET |
YES: Resets stored channel and lock setting to default. ; NO: Cancels. |
|||
|
|
|
|||
*1 |
Displayed only when [USER DEFINED] is selected. |
||||
*2 |
Available only if the connected SiriusXM Vehical Tuner is SXV200 or later that supports |
||||
|
|
SmartFavorites. |
|
|
|
AUX
Preparation:
Select [ON] for [BUILT-IN AUX]. ( 4)
Start listening
1 Connect a portable audio player (commercially available).
Auxiliary input jack
Portable audio player
3.5 mm (1/8") stereo mini plug with “L” shaped connector (commercially available)
2 Press repeatedly to select AUX.
3 Turn on the portable audio player and start playback.
Set the AUX name
While listening to a portable audio player connected to the unit...
1 Press the volume knob to enter [FUNCTION].
2 Turn the volume knob to select [SYSTEM], then press the knob.
3 Turn the volume knob to select [AUX NAME SET], then press the knob.
4Turn the volume knob to make a selection, then press the knob.
AUX (default)/ DVD/ PORTABLE/ GAME/ VIDEO/ TV
5 Press and hold to exit.
To return to the previous setting item, press .
12
BLUETOOTH®
BLUETOOTH — Connection
Supported Bluetooth profiles
–Hands-Free Profile (HFP)
–Serial Port Profile (SPP)
–Phonebook Access Profile (PBAP)
–Advanced Audio Distribution Profile (A2DP)
–Audio/Video Remote Control Profile (AVRCP)
Supported Bluetooth codecs
–Sub Band Codec (SBC)
–Advanced Audio Coding (AAC)
–aptX Codec (aptX)
Connect the microphone
MIC (Microphone input terminal) |
Microphone |
|
|
|
(supplied) |
Rear panel |
|
Adjust the microphone angle
Secure using cord clamps (not supplied) if necessary.
Pair a Bluetooth device
When connecting a Bluetooth device to the unit for the first time, perform pairing between the unit and the device.
1 Press to turn on the unit.
2Search and select this unit model name (KDC-X7**/ KDC-BT7**HD) on the Bluetooth device.
“PAIRING” “PASS XXXXXX”
Device name
“PRESS”
“VOLUME KNOB” scrolls on the display.
•For some Bluetooth devices, you may need to enter the Personal Identification Number (PIN) code immediately after searching.
•Refer also to the manual supplied with your Bluetooth device.
3Press the volume knob to start pairing.
“PAIRING OK” appears when pairing is completed and “” will light up when the Bluetooth connection is established.
•Up to five devices can be registered (paired) in total.
•Only one Bluetooth device can be connected at any time.
•This unit supports Secure Simple Pairing (SSP).
•Some Bluetooth devices may not automatically connect to the unit after pairing. Connect the device to the unit manually. Refer to the instruction manual of the Bluetooth device for more information.
•Once the pairing is completed, the Bluetooth device will remain registered in the unit even if you reset the unit. To delete the paired device, 17, [DEVICE DELETE].
•When you connect iPhone/ iPod touch/ Android device to the USB input terminal, pairing request (via Bluetooth) is automatically activated. Press the volume knob to pair once you have confirmed the device name.
Automatic pairing request is activated only if:
–Bluetooth function of the connected devcie is turned on.
–[AUTO PAIRING] is set to [ON]. ( 17)
–KENWOOD MUSIC PLAY application is installed on the Android device.
ENGLISH 13
BLUETOOTH®
BLUETOOTH — Mobile phone
Receive a call
When there is an incoming call:
–All the buttons and display flash.
–The unit answers the call automatically if [AUTO ANSWER] is set to a selected time. ( 15)
During a call:
–The buttons and display illuminate according to the settings made for [DISPLAY]. ( 20)
–If you turn off the unit or detach the faceplate, the Bluetooth connection is disconnected.
To |
On the faceplate |
On the remote control |
|||
Answer a call |
Press |
or the volume knob or one |
Press . |
||
|
of the number buttons (1 to 6). |
|
|
||
Reject a call |
Press |
|
. |
Press |
. |
|
|
|
|
|
|
End a call |
Press |
or |
. |
Press |
. |
Adjust the phone volume |
Turn the volume knob during a call. |
|
|
||
[00] to [35] (Default: [15]*) |
• This adjustment will not affect the |
|
— |
||
|
volume of the other sources. |
|
|
||
|
|
|
|
|
|
Switch between hands- |
Press |
|
during a call. |
|
|
free and private talk |
• Operations may vary according to |
|
— |
||
modes |
the connected Bluetooth device. |
|
|
||
|
|
|
|
|
|
* Not applicable for iPhone. During a call, the unit synchronizes the phone volume on the iPhone to the unit.
Improve the voice quality
While talking on the phone...
1 Press the volume knob to enter [FUNCTION].
2Turn the volume knob to make a selection (see the following table), then press the knob.
3Repeat step 2 until the desired item is selected or activated.
4 Press and hold to exit.
To return to the previous setting item, press .
|
Default: XX |
MIC GAIN |
–10 — +10 (–4): The sensitivity of |
|
the microphone increases as the number |
|
increased. |
|
|
NR LEVEL |
–5 — +5 (0): Adjust the noise reduction |
|
level until the least noise is being heard |
|
during a phone conversation. |
ECHO CANCEL |
–5 — +5 (0): Adjust the echo cancellation |
|
delay time until the least echo is being heard |
|
during a phone conversation. |
|
|
14
BLUETOOTH®
Make the settings for receiving a call
1 Press to enter Bluetooth mode.
2Turn the volume knob to make a selection (see the following table), then press the knob.
3Repeat step 2 until the desired item is selected or activated.
4 Press and hold to exit.
To return to the previous setting item, press
.
|
|
Default: XX |
SETTINGS |
|
|
|
|
|
|
AUTO ANSWER |
1 — 30: The unit answers incoming |
|
|
call automatically in the selected |
|
|
time (in seconds). ; OFF: Cancels. |
|
|
|
|
BATT/SIGNAL |
AUTO: Shows the strength of the |
|
|
battery and signal when the unit |
|
|
detects a Bluetooth device and the |
|
|
Bluetooth device is connected. ; |
|
|
OFF: Cancels. Clock time is shown. |
|
|
|
Make a call
You can make a call from the call history, phonebook, or dialing the number. Call by voice is also possible if your mobile phone has the feature.
1 Press to enter Bluetooth mode.
2 Turn the volume knob to make a selection (see the following table), then press the knob.
3Repeat step 2 until the desired item is selected/activated or follow the instructions stated on the selected item.
4 Press and hold to exit.
To return to the previous setting item, press .
CALL HISTORY |
1 Press the volume knob to select a name or a phone number. |
||
|
• “INCOMING”, “OUTGOING”, or “MISSED” is shown on the lower part of the display to indicate the |
||
|
|
previous call status. |
|
|
• |
Press |
to change the display category (NUMBER or NAME). |
|
• |
“NO DATA” appears if there is no recorded call history. |
2 Press the volume knob to call.
PHONE BOOK |
1 |
Turn the volume knob quickly to enter alphabet search mode (if the phonebook contains many contacts). |
|
|
The first menu (ABCDEFGHIJK) appears. |
|
|
• To go to the other menu (LMNOPQRSTUV or WXYZ1*), press J/ K. |
|
|
• To select the desired first letter, turn the volume knob or press S / T, then press the knob. |
|
2 |
Select “1” to search with numbers and select “*” to search with symbols. |
|
Turn the volume knob to select a name, then press the knob. |
|
|
3 |
Turn the volume knob to select a phone number, then press the knob to call. |
• If the phone supports PBAP, the phonebook of the connected phone is automatically transferred to the unit when pairing.
• Contacts are categorized as: HOME, OFFICE, MOBILE, OTHER, GENERAL
• This unit can display only non-accent letters. (Accent letters such as “Ú” is showns as “U”.)
ENGLISH 15
BLUETOOTH®
NUMBER DIAL |
1 |
Turn the volume knob to select a number (0 to |
|
|
2 |
9) or character (*, #, +). |
|
|
Press S / T to move the entry position. |
||
|
|
Repeat steps 1 and 2 until you finish entering |
|
|
3 |
the phone number. |
|
|
Press the volume knob to call. |
||
|
1 |
(or using RC-406) |
|
|
Press the number buttons (0 to 9) to enter the |
||
|
2 |
phone number. |
|
|
Press |
to call. |
|
|
|
||
VOICE |
Speak the name of the contact you want to call or |
||
|
the voice command to control the phone functions. |
||
|
( Make a call using voice recognition) |
||
|
|
||
BATT* |
LOW/ MID/ FULL: Shows the strength of the |
||
|
battery. |
|
|
|
|
||
SIGNAL* |
NO SIGNAL/ LOW/ MID/ MAX: Shows the strength |
||
|
of the current received signal. |
||
|
|
|
|
* Functionality depends on the type of the phone used.
Make a call using voice recognition
1Press and hold to activate the connected phone.
2Speak the name of the contact you want to call or the voice command to control the phone functions.
•Supported Voice Recognition features vary for each phone. Refer to the instruction manual of the connected phone for details.
•This unit also supports the intelligent personal assistant function of iPhone.
Delete a contact
1 |
Press |
to enter Bluetooth mode. |
|
2 |
Turn the volume knob to select [CALL HISTORY], then press the knob. |
||
3 |
Turn the volume knob to select a contact. |
||
4 |
Press and hold the volume knob to enter delete mode. |
||
5 |
Turn the volume knob to select [DELETE ONE] or [DELETE ALL], then press the knob. |
||
|
DELETE ONE: Selected name or phone number in step 3 is deleted. |
||
6 |
DELETE ALL: All names or phone numbers in [CALL HISTORY] in step 2 is deleted. |
||
Turn the volume knob to select [YES], then press the knob. |
|||
7 |
Press and hold |
to exit. |
•To return to the previous setting item, press .
•Not applicable for mobile phone that supports PBAP.
Settings in memory
Store a contact in memory
You can store up to 6 contacts into the number buttons (1 to 6).
1 Press to enter Bluetooth mode.
2Turn the volume knob to select [CALL HISTORY], [PHONE BOOK], or [NUMBER DIAL], then press the knob.
3Turn the volume knob to select a contact or enter a phone number.
If a contact is selected, press the volume knob to show the phone number.
4Press and hold one of the number buttons (1 to 6).
“STORED” appears when the contact is stored.
To erase a contact from the preset memory, select [NUMBER DIAL] in step 2 and store a blank number.
Make a call from memory
1 Press to enter Bluetooth mode.
2 Press one of the number buttons (1 to 6).
3Press the volume knob to call.
“NO MEMORY” appears if there is no contacts stored.
16
BLUETOOTH®
Other settings
1 Press the volume knob to enter [FUNCTION].
2 Turn the volume knob to make a selection (see the following table), then press the knob.
3Repeat step 2 until the desired item is selected/activated or follow the instructions stated on the selected item.
4 Press and hold to exit.
To return to the previous setting item, press .
Default: XX
BT MODE
PHONE SELECT
AUDIO SELECT
Selects the phone or audio device to connect or disconnect. “*” appears in front of the device name when connected.
• You can only connect another Bluetooth device by disconnecting the connected Bluetooth device first.
“*” disappears when disconnected.
DEVICE DELETE |
1 |
Turn the volume knob to select a device to delete, then press the knob. |
|
2 |
Turn the volume knob to select [YES] or [NO], then press the knob. |
|
|
|
PIN CODE EDIT |
Changes the PIN code (up to 6 digits). |
|
(0000) |
1 |
Turn the volume knob to select a number. |
|
2 |
Press S / T to move the entry position. |
|
3 |
Repeat steps 1 and 2 until you finish entering the PIN code. |
|
Press the volume knob to confirm. |
|
|
|
|
RECONNECT |
ON: The unit automatically reconnect when the last connected Bluetooth device is within range. ; |
|
|
OFF: Cancels. |
|
|
|
|
AUTO PAIRING |
ON: The unit automatically pair supported Bluetooth device (iPhone/ iPod touch/ Android device) |
|
|
when it is connected through USB input terminal. Depending on the operating system of the |
|
|
connected device, this function may not work. ; OFF: Cancels. |
|
|
|
|
INITIALIZE |
YES: Initializes all the Bluetooth settings (including stored pairing, phonebook, and etc.). ; |
|
|
NO: Cancels. |
Bluetooth test mode
You can check the connectivity of the supported profile between the Bluetooth device and the unit.
• Make sure there is no Bluetooth device paired.
1Press and hold .
“PLEASE PAIR YOUR PHONE PIN 0000” appears.
2Search and select this unit model name
(KDC-X7**/ KDC-BT7**HD) on the
Bluetooth device.
3Operate the Bluetooth device to confirm pairing.
“TESTING” flashes on the display.
The connectivity result (OK or NG) appears after
the test. |
|
|
PAIRING: |
Pairing status |
|
HF CNT: |
Hands-Free Profile (HFP) compatibility |
|
AUD CNT: Advanced Audio Distribution Profile |
||
|
(A2DP) compatibility |
|
PB DL: |
Phonebook Access profile (PBAP) |
|
|
compatibility |
|
To cancel test mode, press and hold |
to |
|
turn off the unit. |
|
ENGLISH 17
BLUETOOTH®
BLUETOOTH — Audio
Audio player via Bluetooth
1 Press repeatedly to select BT AUDIO (or press SRC on RC-406). 2 Operate the Bluetooth audio player to start playback.
To |
On the faceplate |
|
On the remote control |
|
||
Playback / pause |
Press |
. |
|
Press |
. |
|
|
|
|
|
|
|
|
Select group or folder |
Press J/ K. |
|
Press |
/ |
. |
|
|
|
|
|
|
|
|
Reverse / |
Press S / T. |
|
Press S / |
. |
|
|
Forward skip |
|
|
|
|
|
|
Reverse / |
Press and hold S / T. |
Press and hold S / |
|
|||
Fast-forward |
|
|
|
. |
|
|
|
|
|
|
|
|
|
Repeat play |
Press |
repeatedly. |
|
— |
|
|
|
ALL REPEAT, FILE REPEAT, REPEAT OFF |
|
|
|||
|
|
|
|
|||
|
|
|
|
|
|
|
Random play |
Press |
repeatedly. |
|
|
|
|
|
FOLDER RANDOM, RANDOM OFF |
|
— |
|
||
|
|
|
|
|
|
|
|
Press and hold |
to select |
|
|
||
|
|
|
|
|||
|
ALL RANDOM. |
|
|
|
|
|
|
|
|
|
|
|
|
Operations and display indications may differ according to their availability on the connected device.
Internet radio via Bluetooth
Listen to Pandora
Preparation:
Select [ON] for [PANDORA SRC]. ( 4)
You can listen to Pandora on your smart phone (Android OS) through Bluetooth on this unit.
1 Open the Pandora application on your device.
2Connect your Bluetooth audio player via Bluetooth connection. ( 13)
3Press repeatedly to select PANDORA.
The source switches and broadcast starts automatically.
You can operate Pandora in the same way as Pandora for iPod/iPhone. ( 8)
Listen to iHeartRadio
Preparation:
Select [ON] for [IHEART SRC]. ( 4)
You can listen to iHeartRadio on your smart phone (Android OS) through Bluetooth on this unit.
1Open the iHeart Link application on your smart phone.
2Connect your smart phone via Bluetooth connection. ( 13)
3Press repeatedly to select IHEARTRADIO.
The source switches and broadcast starts automatically.
You can operate iHeartRadio in the same way as iHeartRadio for iPod/iPhone. ( 9)
18
AUDIO SETTINGS
While listening to any source...
1 Press the volume knob to enter [FUNCTION].
2Turn the volume knob to select [AUDIO CONTROL], then press the knob.
3Turn the volume knob to make a selection (see the following table), then press the knob.
4 Repeat step 3 until the desired item is selected or activated.
5Press and hold to exit.
(or using RC-406)
1 Press AUD to enter [AUDIO CONTROL].
2 Press J/ K to make a selection, then press .
To return to the previous setting item, press .
|
|
|
|
|
|
Default: XX |
SUB-W LEVEL |
–15 to +15 (0) |
Adjusts the subwoofer output level. |
||||
|
|
|
|
|
|
|
For |
|
|
: |
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
BAND1 LEVEL |
–8 to +8 (+6) |
The sound elements (frequency level, tone level, |
|||
|
|
|
|
|
|
|
|
BAND2 LEVEL |
–8 to +8 (+6) |
Q factor) are preset into each selection (BAND1 |
|||
|
|
|
|
|
|
LEVEL to BAND5 LEVEL). |
|
BAND3 LEVEL |
–8 to +8 (+7) |
||||
|
Adjusts the level to memorize for each source. |
|||||
|
|
|
|
|
|
|
|
|
|
|
–8 to +8 (+3) |
||
|
BAND4 LEVEL |
(Before making an adjustment, select the source |
||||
|
|
|
|
|
|
you want to adjust.) |
|
BAND5 LEVEL |
–8 to +8 (0) |
||||
|
|
|||||
|
|
|
|
|
|
|
For |
|
|
: |
|
||
|
|
|
||||
|
|
|
|
|
|
|
|
BASS LEVEL |
–8 to +8 (+6) |
Adjusts the level to memorize for each source. |
|||
|
|
|
|
|
|
|
|
MID LEVEL |
–8 to +8 (+5) |
(Before making an adjustment, select the source |
|||
|
|
|
|
|
|
you want to adjust.) |
|
TRE LEVEL |
–8 to +8 (0) |
||||
|
|
|||||
|
|
|
|
|
|
|
EQ PRO (for |
|
|
|
) |
|
||
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
BASS ADJUST |
|
BASS CTR FRQ |
60HZ/ 80HZ/ 100HZ/ 200HZ: Selects the center |
|||
|
|
|
|
|
|
|
frequency. |
|
|
|
|
|
BASS LEVEL |
–8 to +8 (+6): Adjusts the level. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
BASS Q FACTOR |
1.00/ 1.25/ 1.50/ 2.00: Adjusts the quality factor. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
BASS EXTEND |
ON: Turns on the extended bass. ; OFF: Cancels. |
|
|
|
|
|
|
|
|
|
|
MID ADJUST |
|
MID CTR FRQ |
0.5KHZ/ 1.0KHZ/ 1.5KHZ/ 2.5KHZ: Selects the center |
|||
|
|
|
|
|
|
|
frequency. |
|
|
|
|
|
|
|
|
|
|
|
|
|
MID LEVEL |
–8 to +8 (+5): Adjusts the level. |
|
|
|
|
|
|
MID Q FACTOR |
0.75/ 1.00/ 1.25: Adjusts the quality factor. |
|
|
|
|
|
|
|
|
|
|
TRE ADJUST |
|
TRE CTR FRQ |
10.0KHZ/ 12.5KHZ/ 15.0KHZ/ 17.5KHZ: Selects the |
|||
|
|
|
|
|
|
|
center frequency. |
|
|
|
|
|
|
|
|
|
|
|
|
|
TRE LEVEL |
–8 to +8 (0): Adjusts the level. |
|
PRESET EQ |
|
DRIVE EQ/ TOP40/ POWERFUL/ ROCK/ POPS/ EASY/ JAZZ/ NATURAL/ |
|||||
|
|
|
|
|
USER: Selects a preset equalizer suitable to the music genre. (Select [USER] |
||
|
|
|
|
|
to use the customized settings.) |
||
|
|
|
|
|
[DRIVE EQ] is a preset equalizer that reduces noise outside the car or |
||
|
|
|
|
|
running noise of the tyres. |
||
BASS BOOST |
|
LEVEL1/ LEVEL2/ LEVEL3: Selects your preferred bass boost level. ; |
|||||
|
|
|
|
|
OFF: Cancels. |
|
|
LOUDNESS |
|
LEVEL1/ LEVEL2: Selects your preferred low and high frequencies boost to |
|||||
|
|
|
|
|
produce a well-balanced sound at a low volume level. ; OFF: Cancels. |
||
|
|
|
|
|
|
|
|
For |
|
|
: |
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
EXTRA EQ |
|
LEVEL1/ LEVEL2/ LEVEL3: Selects your preferred elevation level to enhance |
||||
|
|
|
|
|
the sound in [PRESET EQ]. ; OFF: Cancels. |
||
|
|
|
|
|
|
||
SUBWOOFER SET |
ON: Turns on the subwoofer output. ; OFF: Cancels. |
||||||
|
|
|
|
|
|
|
|
ENGLISH 19
AUDIO SETTINGS
LPF SUBWOOFER |
THROUGH: All signals are sent to the subwoofer. ; 85HZ/ 120HZ/ |
|
160HZ: Audio signals with frequencies lower than 85 Hz/ 120 Hz/ |
|
160 Hz are sent to the subwoofer. |
|
|
SUB-W PHASE |
REVERSE (180°)/ NORMAL (0°): Selects the phase of the subwoofer |
|
output to be in line with the speaker output for optimum |
|
performance. (Selectable only if a setting other than [THROUGH] is |
|
selected for [LPF SUBWOOFER].) |
|
|
HPF |
THROUGH: All signals are sent to the speakers. ; 100HZ/ 120HZ/ |
|
150HZ: Audio signals with frequencies higher than 100 Hz/ 120 Hz/ |
|
150 Hz are sent to the speakers. |
|
|
FADER |
R15 to F15 (0): Adjusts the rear and front speaker output balance. |
|
|
BALANCE |
L15 to R15 (0): Adjusts the left and right speaker output balance. |
|
|
VOLUME OFFSET |
For AUX: –8 to +8 (0) ; For other sources: –8 to 0: Presets the |
|
volume adjustment level of each source. (Before adjustment, select |
|
the source you want to adjust.) |
|
|
SOUND RECNSTR |
ON: Creates realistic sound by compensating the high-frequency |
(Sound reconstruction) |
components and restoring the rise-time of the waveform that are |
|
lost in audio data compression. ; OFF: Cancels. |
[SUB-W LEVEL]/ [LPF SUBWOOFER]/ [SUB-W PHASE] is selectable only if [SUBWOOFER SET] is set to [ON].
DISPLAY SETTINGS
1 Press the volume knob to enter [FUNCTION].
2 Turn the volume knob to select [DISPLAY], then press the knob.
3Turn the volume knob to make a selection (see the following table), then press the knob.
4Repeat step 3 until the desired item is selected/activated or follow the instructions stated on the selected item.
5 Press and hold |
to exit. |
To return to the previous setting item, press .
|
|
Default: XX |
COLOR SELECT |
VARIABLE SCAN/ CUSTOM R/G/B/ preset colors*: Selects your preferred |
|
|
key and display illumination color. |
|
|
|
|
|
You can create your own color (when [CUSTOM R/G/B] or preset colors* is |
|
|
selected). The color you have created can be stored in [CUSTOM R/G/B]. |
|
|
1 |
Press and hold the volume knob to enter the detailed color adjustment. |
|
2 |
Press S / T to select the color (R/ G/ B) to adjust. |
|
3 |
Turn the volume knob to adjust the level (0 — 9), then press the knob. |
|
|
|
DIMMER |
ON: Dims the display and button illumination. ; OFF: Cancels. |
|
|
|
|
BRIGHTNESS |
0 — 31: Selects your preferred brightness level for display and button |
|
|
illumination. |
|
|
|
|
TEXT SCROLL |
AUTO/ ONCE: Selects whether to scroll the display information |
|
|
automatically, or scroll only once. ; OFF: Cancels. |
|
|
|
|
*Preset colors: RED1/ RED2/ RED3/ PURPLE1/ PURPLE2/ PURPLE3/ PURPLE4/ BLUE1/ BLUE2/ BLUE3/ SKYBLUE1/ SKYBLUE2/ LIGHTBLUE/ AQUA1/ AQUA2/ GREEN1/ GREEN2/ GREEN3/ YELLOWGREEN1/ YELLOWGREEN2/ YELLOW/ ORANGE1/ ORANGE2/
ORANGERED
20
MORE INFORMATION
General
•This unit can only play the following CDs:
•Detailed information and notes about the playable audio files are stated in an online manual on the following web site: www.kenwood.com/cs/ce/audiofile/
Playable files
•Playable audio file: MP3 (.mp3), WMA (.wma), AAC (.m4a)
•Playable disc media: CD-R/CD-RW/CD-ROM
•Playable disc file format: ISO 9660 Level 1/2, Joliet, Long file name.
•Playable USB device file system: FAT12, FAT16, FAT32 Even when audio files comply with the standards listed above, playback may be impossible depending on the types or conditions of media or device.
Unplayable discs
•Discs that are not round.
•Discs with coloring on the recording surface or discs that are dirty.
•Recordable/ReWritable discs that have not been finalized.
•8 cm CD. Attempting to insert using an adapter may cause malfunction.
About USB devices
•This unit can play MP3/WMA/AAC/WAV files stored on a USB mass storage class device.
•You cannot connect a USB device via a USB hub.
•Connecting a cable whose total length is longer than 5 m may result in abnormal playback.
•This unit cannot recognize a USB device whose rating is other than 5 V and exceeds 1 A.
About KENWOOD Music Editor Light and KENWOOD
Music Control
•This unit supports the PC application KENWOOD Music Editor Light and Android™ application KENWOOD Music Control.
•When you play audio files with song data added using the KENWOOD Music Editor Light or KENWOOD Music Control, you can search for audio files by Genres, Artists, Albums, Playlists, and Songs.
•KENWOOD Music Editor Light and KENWOOD Music Control are available on the following web site: www.kenwood.com/cs/ce/
About iPod/iPhone
Made for
-iPod touch (2nd, 3rd, 4th, and 5th generation)
-iPod classic
-iPod nano (3rd, 4th, 5th, 6th, and 7th generation)
-iPhone 3G, 3GS, 4, 4S, 5, 5S, 5C
•For the latest compatible list and software versions of iPhone/iPod, see: www.kenwood.com/cs/ce/ipod
•You cannot operate iPod if “KENWOOD” or “” is displayed on iPod.
About Android device
•This unit supports Android OS 4.1 and above.
•Some Android devices (with OS 4.1 and above) may not fully support Android Open Accessory (AOA) 2.0.
•If the Android device supports both mass storage class device and AOA 2.0, this unit always playback via AOA 2.0 as priority.
•For more information and the latest compatible list, see: www.kenwood.com/cs/ce/
About Pandora
•Pandora is available only in the U.S., Australia and New Zealand.
•Because Pandora is a third-party service, the specifications are subject to change without prior notice. Accordingly, compatibility may be impaired, or some or all of the services may become unavailable.
•Some functions of Pandora cannot be operated from this unit.
•For issues using the application, please contact Pandora at pandora-support@pandora.com.
About iHeartRadio
•iHeartRadio® is a third-party service, therefore the specifications are subject to change without prior notice. Accordingly, compatibility may be impaired or some or all of the services may become unavailable.
•Some iHeartRadio® functionality cannot be operated from this unit.
About Bluetooth
•Depending on the Bluetooth version of the device, some Bluetooth devices may not be able to connect to this unit.
•This unit may not work with some Bluetooth devices.
•Signal conditions vary, depending on the surroundings.
•For more information about Bluetooth, visit the following website: www.kenwood.com/cs/ce/
About HD Radio™ Technology
• Program Service Data provides song name, artist, station ID, and other relevant data streams.
• Adjacent to traditional main stations are HD2/HD3 Channels, providing new original formats on the FM dial.
• HD Radio broadcasts deliver crystal clear, CD-like digital audio quality to consumers.
ENGLISH 21
TROUBLESHOOTING
Symptom |
Remedy |
|||
|
Sound cannot be heard. |
• Adjust the volume to the optimum level. |
||
|
|
|
• Check the cords and connections. |
|
|
“MISWIRING CHECK WIRING |
Turn the power off, then check to be sure the |
||
|
THEN PWR ON” appears. |
terminals of the speaker wires are insulated |
||
General |
|
|
properly. Turn the power on again. |
|
appears. |
Send the unit to the nearest service center. |
|||
|
“PROTECTING SEND SERVICE” |
|||
|
• Sound cannot be heard. |
Clean the connectors. ( 2) |
||
|
• The unit does not turn on. |
|
|
|
|
• Information shown on the |
|
|
|
|
|
display is incorrect. |
|
|
|
The unit does not work at all. |
Reset the unit. ( 3) |
||
Radio |
• |
Static noise while listening to |
• |
Pull the antenna out all the way. |
|
• |
Radio reception is poor. |
• |
Connect the antenna firmly. |
HD |
|
the radio. |
|
|
|
|
|
|
|
|
Disc cannot be ejected. |
Press and hold M to forcibly eject the disc. Be |
||
|
|
|
careful not to drop the disc when it is ejected. If this |
|
|
|
|
does not solve the problem, reset the unit. ( 3) |
|
|
Noise is generated. |
Skip to another track or change the disc. |
||
|
|
|
||
iPod |
Tracks do not play back as you |
Playback order is determined when files are |
||
intended them to play. |
recorded. |
|||
/ |
|
|
|
|
CD/ USB |
“READING” keeps flashing. |
Do not use too many hierarchical levels or folders. |
||
|
|
|||
Elapsed playing time is not |
This is caused by how the tracks are recorded. |
|||
|
correct. |
|
|
|
|
Correct characters are not displayed |
This unit can only display uppercase letters, |
||
|
(e.g. album name). |
numbers, and a limited number of symbols. |
||
|
“NA FILE” |
Make sure the disc contains supported audio files. |
||
|
|
|
( |
21) |
Symptom |
Remedy |
||
|
“NO DISC” |
Insert a playable disc into the loading slot. |
|
|
“TOC ERROR” |
Make sure the disc is clean and inserted properly. |
|
|
“PLEASE EJECT” |
Reset the unit. If this does not solve the problem, consult |
|
|
|
your nearest service center. |
|
iPod/ |
“READ ERROR” |
Copy the files and folders onto the USB device again. If this |
|
|
another USB device. |
||
|
|
does not solve the problem, reset the USB device or use |
|
USB |
|
|
|
“NO DEVICE” |
Connect a USB device, and change the source to USB again. |
||
CD / |
|
|
|
“COPY PRO” |
A copy-protected file is played. |
||
|
“NA DEVICE” |
Connect a supported USB device, and check the |
|
|
|
connections. |
|
|
“NO MUSIC” |
Connect a USB device that contains playable audio files. |
|
|
“iPod ERROR” |
• |
Reconnect the iPod. |
|
|
• |
Reset the iPod. |
|
• Sound cannot be heard |
• Reconnect the Android device. |
|
|
during playback. |
• If in [HAND MODE], launch any media player |
|
|
• Sound output only |
|
application on the Android device and start playback. |
|
from the Android |
• If in [HAND MODE], relaunch the current media player |
|
|
device. |
|
application or use another media player application. |
|
|
• Restart the Android device. |
|
ANDROID |
|
• If this does not solve the problem, the connected |
|
|
|
Android device is unable to route the audio signal to |
|
|
|
|
|
|
|
|
unit. ( 21) |
|
Cannot playback at |
• Make sure KENWOOD MUSIC PLAY APP is installed on |
|
|
[BROWSE MODE]. |
|
the Android device. ( 7) |
|
|
• Reconnect the Android device and make the appropriate |
|
|
|
|
setting in [ANDROID SETUP]. ( 7) |
|
|
• If this does not solve the problem, the connected |
|
|
|
|
Android device does not support [BROWSE MODE]. |
|
|
|
( 21) |
22
TROUBLESHOOTING
Symptom |
Remedy |
|||
|
“NO DEVICE” or |
• Switch off the developer options on the Android device. |
||
|
“READING” keeps |
• Reconnect the Android device. |
||
|
flashing. |
• If this does not solve the problem, the connected |
||
ANDROID |
Playback is intermittent |
Android device does not support [BROWSE MODE]. |
||
Turn off the power saving mode on the Android device. |
||||
|
|
( |
21) |
|
|
or sound skips. |
|
|
|
|
“ANDROID ERROR” / |
• Reconnect the Android device. |
||
|
“NA DEVICE” |
• Restart the Android device. |
||
|
“ADD ERROR” / |
New station creation is unsuccessful. |
||
|
“SEARCH ERROR” |
|
|
|
|
“CHECK DEVICE” |
Check the Pandora application on your device. |
||
|
“NO SKIPS” |
The skip limit has been reached. |
||
Pandora |
“NO STATIONS” |
No stations are found. |
||
“STATION LIMIT” |
The number of registered stations has reached its limit. |
|||
|
||||
|
|
Retry after deleting unnecessary stations from your device. |
||
|
“CONNECT ERROR” |
Communication is unstable. |
||
|
“RATING ERROR” |
Registration of thumbs up/thumbs down has failed. |
||
|
“LICENSE ERROR” |
You try to access from a country which Pandora is not |
||
|
|
deliverable. |
||
|
iHeartRadio station |
If “Explicit Content” in [Account Settings] is checked in |
||
|
cannot be selected. |
the web version of iHeartRADIO, custom stations become |
||
iHeartRadio |
|
unavailable. |
||
“CANNOT CREATE” |
Custom station name creation is unsuccessful. |
|||
|
||||
|
“CANNOT SAVE” |
Addition to the favorite category failed. |
||
|
“DISCONNECTED” |
Check the connection to the device. |
||
|
“NO SKIPS” |
The skip limit has been reached. Retry later. |
Symptom |
Remedy |
|
||
|
“NO STATIONS” |
No stations are found. |
|
|
|
“NOT CONNECTED” |
Link to the application is impossible. |
|
|
|
“IHEARTLINK UP” |
Make sure you have installed the latest version of the iHeart |
||
|
|
Link for KENWOOD application on your device. |
|
|
iHeartRadio |
“PLEASE LOGIN” |
You haven’t log in. Log in again. |
|
|
“STATION NOT |
Broadcast from the station is over. |
|
||
|
|
|||
|
AVAILABLE” |
|
|
|
|
“STATION NOT |
No station is selected. |
|
|
|
SELECTED” |
|
|
|
|
“STREAM ERROR” |
Broadcast data is interrupted. |
|
|
|
“THUMB FAILED” |
Registration of Thumbs Up/Down has failed. |
|
|
|
“TIMED OUT” |
The request has resulted in time-out. |
|
|
|
“CH LOCKED LOCK |
The selected channel is locked. Enter the correct pass code to |
||
|
CODE?” |
unlock. ( 12) |
|
|
|
“CHAN UNSUB” |
The selected channel is unsubscribed. Call 1-866-635-2349 in |
||
|
|
U.S.A. or 1-877-438-9677 in Canada to subscribe. ( |
10) |
|
|
“CH UNAVAIL” |
The selected channel is unavailable. Visit www.siriusxm.com |
||
Radio |
|
for more information about the SiriusXM channel lineup. |
||
“CHECK ANTENNA” |
Check the antenna and its connection are in good condition. |
|||
|
||||
SiriusXM® |
“CHECK TUNER” |
Make sure the SiriusXM Vehicle Tuner is connected to the unit. |
||
|
||||
|
“NO SIGNAL” |
Make sure the antenna is mounted outside the vehicle. |
||
|
“SUBSCRIPTION |
Your subscription is updated. Press the volume knob to |
||
|
UPDATED – PRESS |
continue. |
|
|
|
ENTER TO CONTINUE.” |
|
|
|
|
“CODE ERROR” |
Make sure you have entered the correct pass code. ( |
12) |
|
|
“NO CONTENT” |
There is insufficient content to start TuneScan. |
|
|
|
“SCAN CANCEL” |
TuneScan has been aborted. |
|
ENGLISH 23