Kenwood KDC-2016, KDC-4016 User Manual
KDC-4016
COMPACT
DIGITAL AUDIO
KDC-2016
CD-RECEIVER
INSTRUCTION MANUAL
©B64-1548-00 (MW)
Contents
Before use
Safety precautions ........................................................................3
English
Handling Compact discs................................................................5
General features
Power............................................................................................6
Switching Modes ..........................................................................6
Volume..........................................................................................7
Attenuator .....................................................................................7
Loudness ......................................................................................7
Audio Control Setting....................................................................7
ec4/dB (Sound Coordinate) ...........................................................8
Clock display .................................................................................8
Adjusting Time ..............................................................................8
Theft Deterrent Faceplate.............................................................8
Tuner features
Tuning .........................................................................................10
Station Preset Memory...............................................................10
Auto Memory Entry.....................................................................10
Frequency Step Setting...............................................................10
Clean Reception System Circuit (CRSC) .....................................11
CD/External disc control features
Playing CDs.................................................................................12
Playing Other Disc mode ............................................................12
Fast Forwarding and Reversing Disc Play...................................12
Track Search................................................................................12
Disc Search .................................................................................13
Track / Disc Repeat .....................................................................13
Track Scan...................................................................................13
Disc Scan ....................................................................................14
Random Play ...............................................................................14
Magazine Random Play...............................................................14
Basic Operations of remote ................................15
Installation
Accessories.................................................................................17
Installation Procedure..................................................................17
Connecting Wires to Terminals...................................................18
Installation...................................................................................19
Troubleshooting Guide .......................................22
Specifications .....................................................25
— 2 —
Safety precautions
2WARNING
To prevent injury or fire, take the
following precautions:
• Insert the unit all the way in until it is fully
locked in place. Otherwise it may fall out of
place when jolted.
• When extending the ignition, battery, or
ground wires, make sure to use automotivegrade wires or other wires with a 0.75mm
(AWG18) or more to prevent wire
deterioration and damage to the wire coating.
• To prevent a short circuit, never put or leave
any metallic objects (such as coins or metal
tools) inside the unit.
• If the unit starts to emit smoke or strange
smells, turn off the power immediately and
consult your Kenwood dealer.
• Make sure not to get your fingers caught
between the faceplate and the unit.
• Be careful not to drop the unit or subject it to
strong shock.
The unit may break or crack because it
contains glass parts.
• Do not touch the liquid crystal fluid if the LCD
is damaged or broken due to shock. The
liquid crystal fluid may be dangerous to your
health or even fatal.
If the liquid crystal fluid from the LCD
contacts your body or clothing, wash it off
with soap immediately.
2
2CAUTION
To prevent damage to the machine,
take the following precautions:
• Make sure to ground the unit to a negative
12V DC power supply.
• Do not open the top or bottom covers of the
unit.
• Do not install the unit in a spot exposed to
direct sunlight or excessive heat or humidity.
Also avoid places with too much dust or the
possibility of water splashing.
• Do not set the removed faceplate or the
faceplate case in areas exposed to direct
sunlight, excessive heat or humidity. Also
avoid places with too much dust or the
possibility of water splashing.
• To prevent deterioration, do not touch the
terminals of the unit or faceplate with your
fingers.
• Do not subject the faceplate to excessive
shock, as it is a piece of precision equipment.
• When replacing a fuse, only use a new one
with the prescribed rating. Using a fuse with
the wrong rating may cause your unit to
malfunction.
• To prevent a short circuit when replacing a
fuse, first disconnect the wiring harness.
• Do not place any object between the
faceplate and the unit.
• Do not use your own screws. Use only the
screws provided. If you use the wrong
screws, you could damage the unit.
IMPORTANT INFORMATION
You cannot connect the unit directly to the
following CD automatic changers. If you want
to use older changers with the unit, follow
the directions below according to the type of
changer you own:
• KDC-C200 / KDC-C300 / KDC-C400
Use the extension cable and the control box
attached to the CD changer, and the optional
CA-DS100 converter cord.
• KDC-C301 / KDC-C600 / KDC-C800 / KDCC601 / KDC-C401
Use the extension cable attached to the CD
changer, and the optional CA-DS100
converter cord.
• KDC-C100 / KDC-C302 / C205 / C705 /
non-Kenwood CD changers
Cannot be used with this model.
2CAUTION
You can damage both your unit and
the CD changer if you connect them
incorrectly.
2CAUTION
Do Not Load 3-in. CDs in the CD slot
If you try to load a 3 in. CD with its adapter
into the unit, the adapter might separate from
the CD and damage the unit.
— 3 —
Safety precautions
NOTE
• If you experience problems during
installation, consult your Kenwood dealer.
English
• If the unit does not seem to be working right,
try pressing the reset button first. If that does
not solve the problem, consult your Kenwood
dealer.
LOUD
SCAN RDM REP
Reset button
• Characters in the LCD may become difficult
to read in temperatures below 41 ˚F (5 ˚C).
• The illustrations of the display and the panel
appearing in this manual are examples used
to explain more clearly how the controls are
used. Therefore, what appears on the display
in the illustrations may differ from what
appears on the display on the actual
equipment, and some of the illustrations on
the display may represent something
impossible in actual operation.
• The functions that can be used and the
information that can be displayed will differ
depending on the external disc players being
connected.
M.RDM
D.SCN
A.ADJ
AUTO
AME ADJ
Cleaning the Faceplate Terminals
If the terminals on the unit or faceplate get
dirty, wipe them with a dry, soft cloth.
Cleaning the CD Slot
As dust tends to accumulate in the CD slot,
clean it every once in a while. Your CDs can
get scratched if you put them in a dusty CD
Cleaning the Unit
slot.
If the front panel gets dirty, turn off the
power and wipe the panel with a dry silicon
cloth or soft cloth.
SRC
PWR
OFF
CRSC
DISC
DISC
CLK
2CAUTION
Do not wipe the panel with a hard cloth or a
cloth dampened by volatile solvents such as
paint thinner and alcohol. They can scratch
the surface of the panel and/or cause the
indicator letters to peel off.
The marking of products using lasers
(Except for some areas)
CLASS 1
LASER PRODUCT
The label is attached to the chassis/case and
Lens Fogging
Right after you turn on the car heater in cold
weather, dew or condensation may form on
the lens in the CD player of the unit. Called
lens fogging, CDs may be impossible to play.
In such a situation, remove the disc and wait
for the condensation to evaporate. If the unit
still does not operate normally after a while,
consult your Kenwood dealer.
says that the component uses laser beams
that have been classified as Class 1. It means
that the unit is utilizing laser beams that are
of a weaker class. There is no danger of
hazardous radiation outside the unit.
— 4 —
Handling Compact discs
COMPACT
DIGITAL AUDIO
Playing a CD that is dirty, scratched
or warped can cause the sound to
skip and the unit to operate
incorrectly, resulting in worsened
sound quality. Take the following
precautions to prevent your CDs from
getting scratched or damaged.
Handling CDs
• Do not touch the recorded side of the CD
(the side opposite the label) when holding it.
• Do not stick tape on either side of the CD.
Tape
Cleaning CDs
If a CD has gotten dirty, wipe it off gently
using a commercially available cleaning cloth
or a soft cotton cloth, starting from the
center of the disc and moving outward. Do
not clean CDs with conventional record
cleaners, anti-static formulas, or chemicals
such as paint thinner or benzene.
Checking New CDs for Burrs
When playing a new CD for the first time,
check that there are not any burrs stuck to
the perimeter of the disc or in the central
hole. CDs with burrs stuck on them may not
load properly or may skip while playing.
Remove burrs using a ballpoint pen or a
similar utensil.
Do Not Load CD Accessories
Do not use commercially available CD
accessories that can be loaded into the CD
slot, such as stabilizers, protective sheets, or
CD cleaning discs, since they can cause the
unit to malfunction.
Removing the CD
Only remove the CD from the machine in a
horizontal direction, holding it flat. You may
damage the surface of the CD if you try
pulling it down as it ejects.
Do Not Use Special Shape CDs
• Be sure to use round shape CDs only for this
unit and do not use any special shape CDs.
Use of special shape CDs may cause the
unit to malfunction.
Storing CDs
• Do not store CDs in areas exposed to direct
sunlight (such as a car seat or the
dashboard) or other hot places.
• Remove CDs from the unit when not
listening to them for a while, and put them
back in their cases. Do not pile up CDs that
are removed from their cases or prop them
against something.
Burrs
Burrs
• Be sure to use CDs with disc mark
only for this unit.
Do Not Use CDs with Sticker on the
Labeled Side
Do not use the CD with the label sticker
stuck on it.
Using such a CD may cause the CD to be
deformed and the sticker to peel off,
resulting in malfunction of the unit.
— 5 —
#1-5
LOUD
PWR
OFF
AME ADJ
A.ADJ
CRSC
CLK
SCAN RDM REP
D.SCN
M.RDM
DISC
DISC
AUTO
FM
¢
AM
4
SRC
SRC/
PWR OFF
ATT/
LOUD
u
d
AUD/
A.ADJ
CLK
General features
English
ATT indicator
LOUD indicator
Power
Turning on the power:
Press the SRC (source) button.
NOTE
Turn the power on before carrying out the following procedures.
Turning off the power:
Press the PWR OFF button for at least one second.
Switching Modes
Switching Modes:
Each time you press the SRC (source) button, the mode
switches as follows:
▼
Tuner mode
▼
CD mode
▼
External disc control mode 1 (KDC-4016 only)
▼
External disc control mode 2/AUX mode (KDC-4016 only)
▼
Standby mode
Selecting standby mode:
Press the SRC button repeatedly and switch to "OFF"
When "OFF" is displayed, the standby mode is activated.
The standby mode turns all functions off while leaving the
power to the unit on. Use this mode when you want to have
the display illuminated but don't want to listen to anything.
NOTE
• The mode switches to the next mode from any mode which
cannot be used.
• The external disc control mode will differ depending on the unit
that is connected.
• The AUX mode is available only when the changer / AUX
— 6 —
switching adapter (KCA-S210A or CA-C1AX) or CD changer
(KDC-CPS85, KDC-CX85, KDC-CPS82 or KDC-CX82) is
connected to this unit.
During the AUX mode, "AVin" will show in the display.
When the CA-C1AX is being used, the AUX Mode will replace
the External Disc Control Mode.
Volume
Increasing Volume:
Press the u button to turn up the volume.
Decreasing Volume:
Press the d button to turn down the volume.
Attenuator
This function allows you to turn down the volume quickly.
Turning Attenuator On/Off:
Press the ATT button to switch the attenuator on and off.
When the attenuator is on, the ATT indicator blinks.
When the attenuator is off, the volume returns to the original
level.
NOTE
Turning the volume up, or turning it all the way down deactivates
the attenuator function.
Loudness
This function amplifies low and high tones when the volume is
turned down.
The LOUD indicator lights up when the loudness function is on.
Turning Loudness On/Off:
Press the LOUD button for at least one second to switch the
loudness on and off.
Audio Control Setting
Adjust various parameters of sound quality.
1
Press the A.ADJ button for at least one second to enter the
control mode.
2
Selecting mode
Press either the FM or AM button.
Each time the button is pressed, the adjustment mode will
change.
Please refer to the following for the contents of the adjustment
modes.
NOTE
Source tone memory
Each source ( CD, FM, AM and disc changer ) has its own
memory in which to store the bass and treble tone settings.
The settings made for a particular source are recalled
automatically whenever you use that source ( for example, FM
mode uses the tone settings made for FM, AM for AM, etc.).
3
Adjust each mode
Press the 4/¢ button.
Please refer to the following for the adjusting values.
4
Press the AUD button to end the control mode.
"BAS": Adjust the bass level.
Setting values: - 8 - + 8
— 7 —
Grooves
Release button
Projections
General features
English
"TRE": Adjust the treble level.
Setting values: - 8 - + 8
"BL": Adjust the balance level.
Setting values: Left 15 - Right 15
"FD": Adjust the fader level.
Setting values: Front 15 - Rear 15
ec4/dB (Sound Coordinate)
You can recall the best audio setting preset for different types
of the music.
1
Press the AUD button to enter the Sound Coordinate mode.
2
Press a preset button (#1-5).
The preset settings of the bass and treble tones are recalled.
#1: Flat
#2: Rock
#3: Pops
#4: Jazz
#5: Easy
3
Press the AUD button to end the sound coordinate mode.
NOTE
You can call the following settings with this function; bass center
frequency, bass level, bass quality factor, bass extension, treble
center frequency, and treble level setting.
Clock display
Turning clock display On/Off:
Each time you press the CLK button, the display switches
between the clock and each mode display.
Adjusting Time
Adjust the time.
1
When the time is not displayed, first press the CLK button to
display the time.
2
Press the CLK button for at least two seconds to enter the
clock adjustment mode. The time display will blink.
3
• Adjusting the hours
Press the FM button to advance the hours, or press the AM
button to make the hours go back.
• Adjusting the minutes
Press the ¢ button to advance the minutes, or press the
4 button to make the minutes go back.
4
Press the CLK button to end the clock adjustment mode.
Theft Deterrent Faceplate
The faceplate of the unit can be detached and taken with you,
helping to deter theft.
— 8 —
Loading...