and cancel the demonstration
2 Set the clock and date
3 Set the initial settings
RADIO 6
AUX 7
CD / USB / iPod / ANDROID 8
Pandora®
(for )
10
AUDIO SETTINGS 11
DISPLAY SETTINGS 12
TROUBLESHOOTING 13
REFERENCES 15
Maintenance
More information
INSTALLATION /
CONNECTION 17
SPECIFICATIONS 21
2
IMPORTANT
• To ensure proper use, please read through this manual before using this product. It is especially important
that you read and observe Warning and Caution in this manual.
• Please keep the manual in a safe and accessible place for future reference.
Warning
Do not operate any function that takes your attention away from safe driving.
Caution
Volume setting:
• Adjust the volume so that you can hear sounds outside the car to prevent accidents.
• Lower the volume before playing digital sources to avoid damaging the speakers by the sudden increase of
the output level.
General:
• Avoid using the external device if it might hinder safe driving.
•
Make sure all important data has been backed up. We shall bear no responsibility for any loss of recorded data.
• Never put or leave any metallic objects (such as coins or metal tools) inside the unit, to prevent a short
circuit.
• If a disc error occurs due to condensation on the laser lens, eject the disc and wait for the moisture to
evaporate.
• Depending on the types of cars, the antenna will automatically extend when you turn on the unit with
the antenna control wire connected (
parking at a low ceiling area.
Remote control (RC-406):
• Do not leave the remote control in hot places such as on the dashboard.
• The Lithium battery is in danger of explosion if replaced incorrectly. Replace it only with the same or
equivalent type.
• The battery pack or batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
• Keep the battery out of reach of children and in its original packaging when not in used. Dispose of used
batteries promptly. If swallowed, contact a physician immediately.
How to read this manual
• Operations are explained mainly using buttons on the faceplate of .
• English indications are used for the purpose of explanation. You can select the display language from the
[
FUNCTION
• [
• (
] menu. ( 5)
XX
] indicates the selected items.
XX) indicates references are available on the stated page.
19, 20
). Turn off the unit or change the source to STANDBY when
Page 3
BASICS
Faceplate
Display window
Remote control (RC-406)
(Sold separately for /
)
/
Volume knob
Detach button
ToOn the faceplateOn the remote control
Turn on the power
Adjust the volumeTurn the volume knob.Press
Select a source
Change the display informationPress DISP repeatedly. (
Loading slot
enters searching status.
How to resetAttachDetach
Press
• Press and hold to turn off the power.
Press
: Flashes when the unit
Your preset adjustments
will be erased except
stored radio stations.
.
repeatedly.
16)( Not available )
*
Not used
How to replace the battery
Press and hold SRC to turn off the power.
( Pressing SRC does not turn on the power. )
or .
Press ATT during playback to attenuate the sound.
• Press again to cancel.
Press SRC repeatedly.
Remote sensor (Do not expose
to bright sunlight.)
Pull out the
insulation sheet
when using for the
first time.
ENGLISH
3
Page 4
GETTING STARTED
1
Select the display language and cancel the demonstration
When you turn on the power (or after you reset the unit), the display shows:
“SEL LANGUAGE”
1 Turn the volume knob to select the desired display language, [
3 Turn the volume knob to select [
4 Turn the volume knob to make the settings, then press the knob.
Hour
5 Turn the volume knob to select [
6 Turn the volume knob to select [
“PRESS” “VOLUME KNOB”
TUR
] (Turkish), then press the knob.
Minute
“PRESS” “VOLUME KNOB”.
FUNCTION
].
CLOCK
], then press the knob.
CLOCK ADJUST
CLOCK FORMAT
12H
], then press the knob.
], then press the knob.
] or [
24H
], then press the knob.
ENG
]
To set the date
7 Turn the volume knob to select [
knob.
8 Turn the volume knob to select [
press the knob.
9 Turn the volume knob to select [
DATE FORMAT
DD/MM/YY
DATE SET
], then press the
] or [
], then press the knob.
MM/DD/YY
], then
10 Turn the volume knob to make the settings, then press the
knob.
Day
Month Year or Month Day Year
11 Press and hold to exit.
To return to the previous setting item, press .
3
Set the initial settings
Press repeatedly to enter STANDBY.
1
2 Press the volume knob to enter [
• Pressing AUD enters [
AUDIO CONTROL
FUNCTION
] directly.
].
3 Turn the volume knob to select an item (see the following
table), then press the knob.
4 Repeat step 3 until the desired item is selected or activated.
5 Press and hold to exit.
To return to the previous setting item, press .
Default:
AUDIO CONTROL
SWITCH
PREOUT
SP SELECTOFF/ 5/4/ 6 × 9/6/ OEM
REAR/ SUB-W
speakers or a subwoofer are connected to the line out terminals on
the rear (through an external amplifier).
(5inches or 4inches, 6×9inches or 6inches) or OEM speakers for
optimum performance.
or
REAR/ SUBWOOFER
: Selects according to the speaker size
: Selects whether rear
XX
4
Page 5
GETTING STARTED
DISPLAY
EASY MENU
TUNER SETTING
PRESET TYPE
SYSTEM
KEY BEEP
TDF ALARM
SOURCE SELECT
PANDORA SRC
BUILT-IN AUXON
P-OFF WAIT
(For )
ON
:Both display and button illumination change to white color when
entering [
FUNCTION
].;
OFF
remain as [
COLORSELECT
NORMAL
:Memorizes one station for each preset button in each band
(
6, RADIO
regardless of the selected band.
ON
(Except for / / )
ON
is set to OFF.;
(For )
ON
(For / / )
Applicable only when the demonstration mode is turned off.
Sets the duration when the unit will automatically turn off (while in
standby mode) to save the battery.
20M
WAIT TIME – – –
).;
:Activates the keypress tone.;
: Activates the alarm if you forget to detach the faceplate when ACC
OFF
:Enables PANDORA in source selection.;
:Enables AUX in source selection.;
: 20minutes;
:Both display and button illumination
] color. ( 13)
MIX
:Memorizes one station for each preset button,
OFF
:Deactivates.
: Deactivates.
OFF
:Disables. ( 10)
OFF
:Disables. ( 7)
40M
or
OFF – – –
: 40minutes;
:Cancels
60M
: 60minutes;
CD READ1
F/W UPDATE
UPDATE SYSTEM
F/W UP xx.xx
CLOCK
CLOCK DISPLAY
ENGLISH
РУССКИЙ
*
TURKCE
*
ESPANOL
:Automatically distinguishes between audio file disc and music
CD.;
2
:Forces to play as a music CD. No sound can be heard if an
audio file disc is played.
YES
:Starts upgrading the firmware.; NO:Cancels (upgrading is not
activated).
For details on how to update the firmware, see:
www.kenwood.com/cs/ce/
ON
:The clock time is shown on the display even when the unit is
turned off.;
OFF
:Cancels.
Select the display language for [
information if applicable.
By default, [
ENGLISH
*
Selectable only for /
] is selected.
.
FUNCTION
] menu and music
/
ENGLISH
5
Page 6
RADIO
Supported band:
FM1/ FM2/ FM3/ AM/ SW1/ SW2
FM1/ FM2/ FM3/ MW/ LW
Search for a station
1
2 Press repeatedly (or press / on
3 Press S/T (or press S/ on RC-406) to search
• To change the searching method for S/T: Press
repeatedly.
AUTO1 : Automatically search for a station.
AUTO2 : Search for a preset station.
MANUAL : Manually search for a station.
• To store a station: Press and hold one of the number buttons
(1to6).
• To select a stored station: Press one of the number buttons
(1to6) (or press one of the number buttons (1to6) on RC-406).
/ / / /
/ / :
/ / :
Press repeatedly to select TUNER.
RC-406) to select the band.
for a station.
Direct Access Tuning (using RC-406)
Press DIRECT to enter Direct Access Tuning.
1
2 Press the number buttons to enter a frequency.
3 Press to search for a station.
• To cancel, press or DIRECT.
• If no operation is done for 10seconds after step
automatically canceled.
2, Direct Access Tuning is
Other settings
Press the volume knob to enter [
1
FUNCTION
].
2 Turn the volume knob to select an item (see the following table), then
press the knob.
3 Repeat step 2 until the desired item is selected or activated.
4 Press and hold to exit.
To return to the previous setting item, press .
TUNER SETTING
1
LOCAL SEEK
AUTO
MEMORY
MONO SETON
NEWS SETON
REGIONAL
AF SET
*
ON
: Searches only stations with good reception. ;
•
Settings made are applicable only to the selected source/station. Once you change
the source/station, you need to make the settings again.
YES
:Automatically starts memorizing 6 stations with good reception.; NO:Cancels.
•
Selectable only if [
:Improves the FM reception, but the stereo effect may be lost.;
: The unit will temporarily switch to News Programme if available. ;
2
*
ON
: Switches to another station only in the specific region using the “AF” control.;
OFF
:Cancels.
2
*
ON
: Automatically searches for another station broadcasting the same program
in the same Radio Data System network with better reception when the current
reception is poor.;
NORMAL
OFF
] is selected for [
:Cancels.
OFF
: Cancels.
PRESET TYPE
]. ( 5)
OFF
Default:
:Cancels.
OFF
: Cancels.
XX
6
Page 7
RADIO
TION
PTY SEARCH1 Press the volume knob to enter PTY language selection.
CLOCK
TIME SYNC
1
*
2
*
Available Program Type
SPEECH : NEWS, AFFAIRS, INFO
MUSIC
:
The unit will search for the Program Type categorized under [
[
MUSIC
] if selected.
• [
MONO SET
when the band is FM1/ FM2/ FM3.
• If the volume is adjusted during reception of traffic information, alarm or news
bulletin, the adjusted volume is memorized automatically. It will be applied the
next time traffic information, alarm or news bulletin is turned on.
:Allows the unit to temporarily switch to Traffic Information if available (“TI”
lights up).;
OFF
:Cancels.
2
Turn the volume knob to select the PTY language (
GERMAN
3
4
ON
OFF
/ / / / /
/ : AM/ SW1/ SW2 stations only.
/ / / / /
/ : Default: [
SCIENCE, VARIED, WEATHER, FINANCE, CHILDREN, SOCIAL, RELIGION, PHONE IN
TRAVEL, LEISURE, DOCUMENT
POP M
(music),
OTHER M
]/ [
NEWS SET
), then press the knob.
Turn the volume knob to select the available Program Type (see the following).
Press
S / T
:Synchronizes the unit’s time to the Radio Data System station time.;
:Cancels.
/
/ : FM stations only.
/
/ : Default: [ON]
(music),
]/ [
to start searching.
OFF
]
(information),
ROCK M
(music),
]/ [
EASY M
AF SET
JAZZ, COUNTRY, NATION M
REGIONAL
SPORT, EDUCATE, DRAMA, CULTURE
(music),
]/ [TI]/ [
LIGHT M
(music),
PTY SEARCH
ENGLISH/ FRENCH
(music),
SPEECH
CLASSICS
(music)
] or
OLDIES, FOLK M
] is selectable only
/
,
,
AUX
Preparation:
Select [
ON
] for [
BUILT-IN AUX
Start listening
Connect a portable audio player (commercially available).
1
Auxiliary input jack
3.5mm stereo mini plug with “L” shaped
connector (commercially available)
2 Press repeatedly to select AUX.
3 Turn on the portable audio player and start playback.
Set the AUX name
While listening to a portable audio player connected to the unit...
1 Press the volume knob to enter [
2 Turn the volume knob to select [
knob.
3 Turn the volume knob to select [
,
knob.
4 Turn the volume knob to select an item, then press the
knob.
AUX
(default)/
5 Press and hold to exit.
To return to the previous setting item, press .
]. ( 5)
Portable audio player
FUNCTION
SYSTEM
], then press the
AUX NAME SET
DVD/ PORTABLE/ GAME/ VIDEO/ TV
].
], then press the
ENGLISH
7
Page 8
CD / USB / iPod / ANDROID
Start playback
The source changes automatically and
playback starts.
M
Eject disc
USB input terminal
USB
CA-U1EX (max.: 500mA)
(optional accessory)
iPod/iPhone
ANDROID
Micro USB 2.0 cable
(commercially available)
Label side
(for )
KCA-iP102 / KCA-iP103
(optional accessory)
or accessory cable of the
iPod/iPhone
*
2
*
3
*
2
*
1
ToOn the faceplateOn the remote control
Playback / pausePress .
4
Reverse / Fast-forward
Select a track/file
Select a folder
6
Repeat play
*
*
Press and hold S/T.Press and hold S/.
Press S/T.Press S/
5
*
Press J/K.
Press repeatedly.
TRACK REPEAT/ ALL REPEAT
FILE REPEAT/ FOLDER REPEAT/ ALL REPEAT
FILE REPEAT/ FOLDER REPEAT/ REPEAT OFF
6
Random play
*
Press repeatedly.
DISC RANDOM/ RANDOM OFF
FOLDER RANDOM/ RANDOM OFF
: Audio CD
: Audio CD
Press
.
.
Press
/ .
: MP3/WMA/WAV/FLAC file
: iPod or ANDROID
: MP3/WMA/WAV/FLAC file, iPod or
ANDROID
7
Press and hold
1
*
KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type
2
*
Do not leave the cable inside the car when not using.
3
*
When connecting an Android device, “Press [VIEW] to install KENWOOD MUSIC PLAY APP” is shown. Follow the instructions
to select
ALL RANDOM
*
.
to install the application. You can also install the latest version of KENWOOD MUSIC PLAY application on your Android device
before connecting. (
4
*
For ANDROID: Applicable only when [
5
*
For CD: Only for MP3/WMA files. This does not work for iPod/ ANDROID.
6
*
For iPod/ ANDROID: Applicable only when [
7
*
For CD: Only for MP3/WMA files.
15)
BROWSE MODE
MODE OFF
] is selected. (
]/ [
BROWSE MODE
9)
] is selected. (
9)
8
Page 9
CD / USB / iPod / ANDROID
Select control mode
While in iPod source, press 5 repeatedly.
MODE ON
: Control iPod using the iPod itself
play/pause, file skip, fast-forward or reverse from this
MODE OFF
While in ANDROID source, press 5 repeatedly.
BROWSE MODE
HAND MODE
unit.
: Control iPod from this unit.
: Control Android device from this unit via KENWOOD
MUSIC PLAY application installed in the Android
device.
: Control Android device using the Android device
itself via other media player applications installed
in the Android device. However, you can still play/
pause and file skip from this unit.
. However,
you can still
Select music drive
Press 5 repeatedly.
Stored songs in the following drive will be played back.
• Selected internal or external memory of a smartphone (Mass
Storage Class).
• Selected drive of a multiple drives device.
Select a file from a folder/list
Press .
1
2 Turn the volume knob to select a folder/list, then press the knob.
3 Turn the volume knob to select a file, then press the knob.
Quick Search
If you have many files in the iPod, you can search through them quickly
according to the first character of the file name.
Turn the volume knob quickly to enter character search.Turn the volume knob to select the character.
To search for a character other than A to Z and 0to9, enter only “ * ”.
Press S/T to move to the entry position.
• You can enter up to 3characters.
Press the volume knob to start searching.
• To return to the root folder/ first file/ top menu, press 5.
• To return to the previous setting item, press
• To cancel, press and hold
• For iPod, applicable only when [
• For ANDROID, applicable only when [
.
MODE OFF
BROWSE MODE
] is selected.
.
] is selected.
Direct Music Search (using RC-406)
Press DIRECT.
1
2 Press the number buttons to enter a track/file number.
3 Press to search for music.
• To cancel, press or DIRECT.
• Not available if Random Play is selected.
• Not applicable for iPod and ANDROID.
ENGLISH
9
Page 10
CD / USB / iPod / ANDROID
Listen to TuneIn Radio/ TuneIn Radio Pro/
Aupeo
(for )
While listening to TuneIn Radio, TuneIn Radio Pro or
Aupeo, connect the iPod/iPhone to the USB input
terminal of the unit.
• The unit will output the sound from these
applications.
Pandora®
(for )
Preparation:
Install the latest version of the Pandora application on your device (iPhone/ iPod touch), then
create an account and log in to Pandora.
• Select [
ON
] for [
PANDORA SRC
]. ( 5)
Start listening
Open the Pandora application on your device.
1
2 Connect your device to the USB input terminal.
Other settings
Press the volume knob to enter [
1
FUNCTION
].
2 Turn the volume knob to select an item (see
the following table), then press the knob.
3 Repeat step 2 until the desired item is selected
or activated.
4 Press and hold to exit.
To return to the previous setting item, press .
Default:
USB
MUSIC DRIVEDRIVE CHANGE
to [
DRIVE 5
:The next drive ([
DRIVE 1
]) is selected automatically and
playback starts.
Repeat steps
1
to 3 to select the following
drives.
SKIP SEARCH0.5%/ 1%/ 5%/ 10%
: While listening to
iPod or ANDROID, selects the skip search ratio
over the total files.
10
USB input terminal
1
*
or
2
*
KCA-iP102 / KCA-iP103 (optional accessory)
accessory cable of the iPod/iPhone
The source changes to PANDORA and broadcast starts.
ToOn the faceplateOn the remote control
XX
Playback / pause
Skip a track
]
Thumbs up or thumbs down
1
*
KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type
2
*
Do not leave the cable inside the car when not using.
3
*
If thumbs down is selected, the current track is skipped.
Press
Press T.
3
*
Press J/K.
.Press
Press
Press
Create and save a new station
Press .
1
2 Turn the volume knob to select [
3 Turn the volume knob to select [
NEW STATION
FROM TRACK
], then press the knob.
] or [
FROM ARTIST
], then press the knob.
A new station is created based on the current song or artist.
4 Press and hold one of the number buttons (1to5) to store.
To select a stored station, press one of the number buttons (1to5).
.
.
/ .
Page 11
Pandora®
(for )
Search for a registered station
Press .
1
2 Turn the volume knob to select an item, then press the knob.
[
BY DATE
[
]:According to the registered date
A-Z
]:Alphabetical order
3 Turn the volume knob to select the desired station, then press
the knob.
To cancel, press and hold
.
(or using RC-406)
Press J / K to search for a station, then press .
Bookmark current song information
Press and hold the volume knob.
“BOOKMARKED” appears and the information is stored to your
device. The bookmark is available on your Pandora account but not
on this unit.
Delete a station
While listening to PANDORA...
1 Press the volume knob to enter [
2 Turn the volume knob to select [
3 Turn the volume knob to select [
knob.
4 Turn the volume knob to select [
the knob.
FUNCTION
].
SYSTEM
], then press the knob.
STATION DEL
A-Z
] or [
BY DATE
], then press the
], then press
5 Turn the volume knob to select the desired station to delete,
then press the knob.
6 Turn the volume knob to select [
YES
], then press the knob.
7 Press and hold to exit.
To return to the previous setting item, press .
AUDIO SETTINGS
While listening to any source...
1 Press AUD to enter [
2 Turn the volume knob to select an item (see the following table), then
press the knob.
3 Repeat step 2 until the desired item is selected or activated.
4 Press and hold to exit.
(or using RC-406)
1 Press AUD to enter [
2 Press J / K to select an item, then press .
“NO DISC”Insert a playable disc into the loading slot.
“TOC ERROR”Make sure the disc is clean and inserted properly.
“PLEASE EJECT”Reset the unit. If this does not solve the problem, consult
“READ ERROR”Copy the files and folders onto the USB device again. If this
“NO DEVICE”Connect a USB device, and change the source to USB again.
CD / USB / iPod
“COPY PRO”A copy-protected file is played.
“NA DEVICE”
“NO MUSIC”Connect a USB device that contains playable audio files.
“iPod ERROR”
•
Sound cannot
be heard during
playback.
•
Sound output only
from the Android
device.
ANDROID
Cannot playback at
[
BROWSE MODE
your nearest service center.
does not solve the problem, reset the USB device or use
another USB device.
Connect a supported USB device, and check the connections.
•
Reconnect the iPod.
•
Reset the iPod.
•
Reconnect the Android device.
•
If in [
HAND MODE
on the Android device and start playback.
•
If in [
HAND MODE
application or use another media player application.
•
Restart the Android device.
•
If this does not solve the problem, the connected Android
device is unable to route the audio signal to unit. (
•
Make sure KENWOOD MUSIC PLAY APP is installed on the
].
Android device. (
•
Reconnect the Android device and select the appropriate
control mode.
•
If this does not solve the problem, the connected Android
device does not support [
], launch any media player application
], relaunch the current media player
8)
BROWSE MODE
]. ( 16)
SymptomRemedy
“NO DEVICE” or
“READING” keeps
flashing.
ANDROID
Playback is intermittent
or sound skips.
“ANDROID ERROR” /
“NADEVICE”
“ADDERROR”New station creation is unsuccessful.
“CHECKDEVICE”Check the Pandora application on your device.
“NOSKIPS”The skip limit has been reached.
“NOSTATIONS”No stations are found.
“STATIONLIMIT”
“CONNECT ERROR”Communication is unstable.
Pandora
“RATING ERROR”Registration of thumbs up/thumbs down has failed due to
“THUMBS N/A”Registration of thumbs up/thumbs down is not allowed.
“LICENSE ERROR”You try to access from a country which Pandora is not
16)
Muting upon the reception of a phone call
Connect the MUTE wire to your telephone using a commercial telephone accessory.
(
19, 20
)
When a call comes in, “CALL” appears.
•
To continue listening to the audio system during a call, press . “CALL” disappears
and the audio system resumes.
When the call ends, “CALL” disappears.
•
Switch off the developer options on the Android device.
•
Reconnect the Android device.
•
If this does not solve the problem, the connected
Android device does not support [
(
16)
Turn off the power saving mode on the Android device.
•
Reconnect the Android device.
•
Restart the Android device.
The number of registered stations has reached its limit.
Retry after deleting unnecessary stations from your device.
insufficient network connectivity.
deliverable.
(The audio system pauses.)
(The audio system resumes.)
BROWSE MODE
].
14
Page 15
REFERENCES
Maintenance
Cleaning the unit
Wipe off dirt on the faceplate with a dry silicone or soft cloth.
Cleaning the connector
Detach the faceplate and clean the connector gently
with a cotton swab, being careful not to damage
the connector.
Handling discs
•
Do not touch the recording surface of the disc.
•
Do not stick tape etc. on the disc, or use a disc with tape stuck on it.
•
Do not use any accessories for the disc.
•
Clean from the center of the disc and move outward.
•
Clean the disc with a dry silicone or soft cloth. Do not use any solvents.
•
When removing discs from this unit, pull them out horizontally.
•
Remove burrs from the center hole and disc edge before inserting a disc.
More information
Visit also the following website <www.kenwood.com/cs/ce/> for:
–
Latest firmware updates and latest compatible item list
–
Android™ application KENWOOD MUSIC PLAY
–
Any other latest information
General
•
This unit can only play the following CDs:
•
Detailed information and notes about the playable audio files are stated in an online manual
on the following website: www.kenwood.com/cs/ce/audiofile/
Connector (on the reverse
side of the faceplate)
Playable files
•
Playable audio file: MP3 (.mp3), WMA (.wma)
•
Playable disc media: CD-R/CD-RW/CD-ROM
•
Playable disc file format: ISO 9660 Level 1/2, Joliet, Long file name.
•
Playable USB device file system: FAT12, FAT16, FAT32
Even when audio files comply with the standards listed above, playback may be impossible
depending on the types or conditions of media or device.
Unplayable discs
•
Discs that are not round.
•
Discs with coloring on the recording surface or discs that are dirty.
•
Recordable/ReWritable discs that have not been finalized.
•
8cm CD. Attempting to insert using an adapter may cause malfunction.
About USB devices
•
This unit can play MP3/WMA/WAV/FLAC files stored on a USB mass storage class device.
•
You cannot connect a USB device via a USB hub.
•
Connecting a cable whose total length is longer than 5m may result in abnormal playback.
•
This unit cannot recognize a USB device whose rating is other than 5V and exceeds 1A.
About iPod/iPhone
Made for
-
iPod touch (2nd, 3rd, 4th, and 5th generation)
-
iPod classic
-
iPod nano (3rd, 4th, 5th, 6th, and 7th generation)
-
iPhone 3G, 3GS, 4, 4S, 5, 5S, 5C, 6, 6 Plus
•
You cannot operate iPod if “KENWOOD” or “ ” is displayed on iPod.
ENGLISH
15
Page 16
REFERENCES
About Android device
•
This unit supports Android OS 4.1 and above.
•
Some Android devices (with OS 4.1 and above) may
not fully support Android Open Accessory (AOA) 2.0.
•
If the Android device supports both mass storage
class device and AOA 2.0, this unit always playback
via AOA 2.0 as priority.
Change the display information
Each time you press
•
If the information is unavailable or not recorded,
Source name
DISP
, the display information changes.
“NO TEXT”, “NO INFO”, or other information (eg. station name, playing time) appears.
/ / /
/ / /
/ /
About Pandora
•
Pandora is only available in certain countries.
Please visit <http://www.pandora.com/legal> for
more information.
•
Because Pandora is a third-party service, the
specifications are subject to change without
prior notice. Accordingly, compatibility may be
impaired, or some or all of the services may become
unavailable.
•
Some functions of Pandora cannot be operated from
this unit.
•
For issues using the application, please contact
Pandora at pandora-support@pandora.com.
16
STANDBY
TUNER
CD or USB
IPOD or
ANDROID
PANDORA
AUX
Source name (Date/Clock)Source name Clock (back to the beginning)
Frequency (Date/Clock)Frequency Clock (back to the beginning)
(For FM Radio Data System stations only)
Station name (Date/Clock) Radio text (Date/Clock)
Radio text+ (R.TEXT+)
Frequency (Date/Clock)
(For CD-DA)
Track title (Artist) Track title (Disc name) Track title
(Date/Clock)
(back to the beginning)
(For MP3/WMA/WAV/FLAC files)
Track title (Artist) Track title (Album title) Track title
(Date/Clock)
(Date/Clock)
(back to the beginning)
Track title (Artist) Track title (Album name) Track title
(Date/Clock)
(back to the beginning)
Station name (Date/Clock) Shared / Radio station
(Date/Clock)
Track title (Date/Clock)
(back to the beginning)
Source name (Date/Clock)Source name Clock (back to the beginning)
Title (Artist) Title (Date/Clock)
(back to the beginning)
Playing time (Date/Clock)
File name (Folder name) File name
Playing time (Date/Clock)
Playing time (Date/Clock)
Track title (Artist) Track title (Album title)
Playing time (Date/Clock)
(For FM Radio Data System stations only)
Station name Radio text Radio text+
Title/Artist
(back to the beginning)
(For CD-DA)
Disc name/Artist Track title/Artist Playing time
Clock
(For MP3/WMA/WAV/FLAC files)
Track title/Artist Album title/artist Folder name
File name
(back to the beginning)
Track title/Artist
Clock
Frequency Clock
(back to the beginning)
Playing time Clock
Album title/Artist Playing time
(back to the beginning)
—
Page 17
INSTALLATION / CONNECTION
Warning
•
The unit can only be used with a 12V DC power supply, negative ground.
•
Disconnect the battery’s negative terminal before wiring and mounting.
•
Do not connect Battery wire (yellow) and Ignition wire (red) to the car chassis or Ground wire
(black) to prevent a short circuit.
•
Insulate unconnected wires with vinyl tape to prevent a short circuit.
•
Be sure to ground this unit to the car’s chassis again after installation.
Caution
•
For safety’s sake, leave wiring and mounting to professionals. Consult the car audio dealer.
•
Install this unit in the console of your vehicle. Do not touch the metal parts of this unit during
and shortly after use of the unit. Metal parts such as the heat sink and enclosure become hot.
•
Do not connect the [ wires of speakers to the car chassis or Ground wire (black), or connect
them in parallel.
•
Mount the unit at an angle of less than 30º.
•
If your vehicle wiring harness does not have the ignition terminal, connect Ignition wire (red)
to the terminal on the vehicle’s fuse box which provides 12 V DC power supply and is turned
on and off by the ignition key.
•
Keep all cables away from heat dissipate metal parts.
•
After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are
working properly.
•
If the fuse blows, first make sure the wires are not touching car’s chassis, then replace the old
fuse with one that has the same rating.
Basic procedure
1
Remove the key from the ignition switch, then disconnect the [
terminal of the car battery.
2 Connect the wires properly.
See Wiring connection. (
3 Install the unit to your car.
See Installing the unit (in-dash mounting).
4 Connect the [ terminal of the car battery.
5 Reset the unit. (
19, 20
)
3
)
Part list for installation
(A)
Faceplate
(C)
Mounting sleeve
(E)
Wiring harness
/ /
/ /
(B)
Trim plate
(D)
Extraction key
/ / / /
ENGLISH
17
Page 18
INSTALLATION / CONNECTION
Installing the unit (in-dash mounting)
Hook on the top side
Orientate the trim plate as
illustrated before fitting.
How to remove the unit
1
Detach the faceplate.
2 Fit the catch pin on the
extraction keys into the holes
on both sides of the trim plate,
then pull it out.
3 Insert the extraction keys
deeply into the slots on each
side, then follow the arrows as
shown on the right.
Do the required wiring.
(
19, 20
)
Dashboard of
your car
Bend the appropriate tabs to hold the
mounting sleeve firmly in place.
When installing without the mounting sleeve
1
Remove the mounting sleeve and trim plate from the unit.
2 Align the holes in the unit (on both sides) with the vehicle
mounting bracket and secure the unit with screws
(supplied).
– – – – – or – – – – –
The following screws are supplied for:
/ / :
Use only the specified screws. Using wrong screws might damage the unit.
/ / / /
/ / :
Round head screws (M5 × 8mm) × 4
Flat head screws (M5 × 8mm)× 4
Sems screws (M4 × 8mm)× 1
Round head screws (Ø5 × 8mm) × 4
Flat head screws (Ø5 × 8mm)× 4
Sems screws (M4 × 8mm)× 1
To secure the mounting
bracket
To secure the ground
wire (black)
To secure the mounting
bracket
To secure the ground
wire (black)
18
Page 19
INSTALLATION / CONNECTION
Wiring connection
IMPORTANT
and leave this job to professionals for your safety. Consult your car audio dealer.
: We recommend installing the unit with a commercially available custom wiring harness specific for your car
(for
Front/ Rear/ subwoofer output
/ / / / / /
)
When connecting to an external amplifier, connect its ground
wire to the car’s chassis to avoid damaging the unit.
Battery
Antenna terminal
To front speaker (left)
To front speaker (right)
To rear speaker (left)
To rear speaker (right)
Ignition switch
Car fuse box
Car fuse box
White
White/Black
Gray
Gray/Black
Green
Green/Black
Purple
Purple/Black
Red (Ignition wire)
Yellow (Battery wire)
Black (Ground wire)
To the metallic body or chassis of the car
Fuse (10A)
If no connections are made, do not let the wire come out from the tab.
Brown
(Mute control wire)
Blue/White
(Power control wire/
Antenna control wire)
Light blue/yellow
(Steering remote control wire)
To the terminal that is grounded when the telephone
rings or during conversation
(To connect the Kenwood navigation system, refer your
navigation manual.)
To the power control terminal when using the optional
power amplifier or to the antenna control terminal in
the vehicle
To the steering wheel remote control adapter
( 14)
ENGLISH
19
Page 20
INSTALLATION / CONNECTION
Wiring connection
Connecting the ISO connectors on some VW/Audi or
Opel (Vauxhall) automobiles
You may need to modify the wiring of the supplied
wiring harness as illustrated below.
A7 (Red)
A4 (Yellow)
Pin
A4 Yellow: Battery
A5 Blue/White: Power control
A7 Red: Ignition (ACC)
A8 Black: Earth (ground) connection
B1
Purple
B2
Purple/black
B3
Gray
]
B4
Gray/black
B5
White
B6
White/black
B7
Green
B8
Green/black
20
]
]
]
(for
Default wiring
Color and function
[
[
[
[
Antenna terminal
Ignition wire
(Red)
Battery wire
(Yellow)
: Rear speaker (right)
: Front speaker (right)
: Front speaker (left)
: Rear speaker (left)
/ /
UnitVehicle
)
Yellow (Battery wire)
Red (Ignition wire)
Red (A7)
Yellow (A4)
Fuse (10A)Front/ Rear/ subwoofer output
Brown
(Mute control wire)
Blue/White
(Power control wire/
Antenna control wire)
Light blue/yellow
(Steering remote control
wire)
If your car does not have an ISO terminal :
We recommend installing the unit with a commercially
available custom wiring harness specific for your car and
leave this job to professionals for your safety. Consult your
car audio dealer.
When connecting to an external amplifier, connect its
ground wire to the car’s chassis to avoid damaging the unit.
If no connections are made, do not let the wire come out from the tab.
To the terminal that is grounded
MUTE
when the telephone rings or during
conversation
( 14)
(To connect the Kenwood
navigation system, refer your
navigation manual.)
ANT CONT
P. CONT
To the power control terminal
when using the optional power
amplifier or to the antenna control
terminal in the vehicle
STEERING WHEEL
REMOTE INPUT
REMOTE CONT
To the steering wheel remote
control adapter
ISO connectors
Page 21
SPECIFICATIONS
For / / / /
FM Frequency Range87.5 MHz — 108.0 MHz (50 kHz space)
Дата изготовления (месяц/год) находится на этикетке устройства.
/ /
For Turkey
Bu ürün 28300 sayılı Resmi Gazete’de yayımlanan Atik Elektrikli ve Elektronik Eşyalarin Kontrolü
Yönetmeliğe uygun olarak üretilmiştir.
Eski Elektrik ve Elektronik Ekipmanların İmha Edilmesi Hakkında Bilgi (atık yan ürün
toplama sistemlerini kullanan ülkeleri için uygulanabilir)
Sembollü (üzerinde çarpı işareti olan çöp kutusu) ürünler ev atıkları olarak
atılamaz.
Eski elektrik ve elektronik ekipmanlar, bu ürünleri ve ürün atıklarını geri
dönüştürebilecek bir tesiste değerlendirilmelidir. Yaşadığınız bölgeye en yakın
geri dönüşüm tesisinin yerini öğrenmek için yerel makamlara müracaat edin.
Uygun geri dönüşüm ve atık imha yöntemi sağlığımız ve çevremiz üzerindeki
zararlı etkileri önlerken kaynakların korunmasına da yardımcı olacaktır.
/ /
)
:
Declaration of Conformity with regard to the EMC Directive
Declaration of Conformity with regard to the RoHS Directive
2011/65/EU
Manufacturer:
JVC KENWOOD Corporation
3-12, Moriya-cho, Kanagawa-ku, Yokohama-shi, Kanagawa, 221-0022,
Japan
EU Representative:
JVCKENWOOD NEDERLAND B.V.
Amsterdamseweg 37, 1422 AC UITHOORN, The Netherlands
The marking of products using lasers
The label is attached to the chassis/case and says that the
component uses laser beams that have been classified
as Class1. It means that the unit is utilizing laser beams
that are of a weaker class. There is no danger of hazardous
radiation outside the unit.
• “Made for iPod,” and “Made for iPhone” mean that an electronic accessory has been designed to
connect specifically to iPod, or iPhone, respectively, and has been certified by the developer to
meet Apple performance standards. Apple is not responsible for the operation of this device or
its compliance with safety and regulatory standards. Please note that the use of this accessory
with iPod or iPhone may affect wireless performance.
• iPhone, iPod, iPod classic, iPod nano, and iPod touch are trademarks of Apple Inc., registered in
the U.S. and other countries.
• Lightning is a trademark of Apple Inc.
• Android is trademark of Google Inc.
• Pandora, the Pandora logo, and the Pandora trade dress are trademarks or registered
trademarks of Pandora Media, Inc., used with permission.
libFLAC
Copyright (C) 2000,2001,2002,2003,2004,2005,2006,2007,2008,2009 Josh Coalson
Redistribution and use in source and binary forms, with or without modification, are permitted
provided that the following conditions are met:
- Redistributions of source code must retain the above copyright notice, this list of conditions and
the following disclaimer.
- Redistributions in binary form must reproduce the above copyright notice, this list of conditions
and the following disclaimer in the documentation and/or other materials provided with the
distribution.
- Neither the name of the Xiph.org Foundation nor the names of its contributors may be used
to endorse or promote products derived from this software without specific prior written
permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND ONTRIBUTORS “AS IS” AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
THE FOUNDATION OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
ENGLISH
23
Page 24
Page 25
Page 26
• “Made for iPod,” and “Made for iPhone” mean that an electronic accessory has been designed
to connect specifically to iPod, or iPhone, respectively, and has been certified by the
developer to meet Apple performance standards. Apple is not responsible for the operation
of this device or its compliance with safety and regulatory standards. Please note that the
use of this accessory with iPod or iPhone may affect wireless performance.
• iPhone, iPod, iPod classic, iPod nano, and iPod touch are trademarks of Apple Inc., registered
in the U.S. and other countries.
• Lightning is a trademark of Apple Inc.
• Android is trademark of Google Inc.
• Pandora, the Pandora logo, and the Pandora trade dress are trademarks or registered
trademarks of Pandora Media, Inc., used with permission.
libFLAC
Copyright (C) 2000,2001,2002,2003,2004,2005,2006,2007,2008,2009 Josh Coalson
Redistribution and use in source and binary forms, with or without modification, are permitted
provided that the following conditions are met:
- Redistributions of source code must retain the above copyright notice, this list of conditions
and the following disclaimer.
- Redistributions in binary form must reproduce the above copyright notice, this list of
conditions and the following disclaimer in the documentation and/or other materials
provided with the distribution.
- Neither the name of the Xiph.org Foundation nor the names of its contributors may be used
to endorse or promote products derived from this software without specific prior written
permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND ONTRIBUTORS “AS IS”
AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS BE LIABLE FOR
ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY
OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE.