• Updated information (the latest Instruction Manual, system updates, new
functions, etc.) is available from
<http://www.kenwood.com/cs/ce/>.
Take the time to read through this instruction manual.
Familiarity with installation and operation procedures will help you obtain the best performance from your new
GPS Navigation System.
For your records
Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space
provided below. Refer to the model and serial numbers whenever you call upon your KENWOOD dealer for information or
service on the product.
Model DDX9904S/ DDX9704S/ DMX7704S Serial number
US Residence Only
Register Online
Register your KENWOOD product at www.kenwoodusa.com
About this Unit ..........................................................99
3English
Page 4
Before Use
Before Use
Precautions
# WARNINGS
Ñ To prevent injury or fire, take
the following precautions:
• To prevent a short circuit, never put or leave
any metallic objects (such as coins or metal
tools) inside the unit.
• Do not watch or fix your eyes on the unit’s
display when you are driving for any extended
period.
• If you experience problems during installation,
consult your KENWOOD dealer.
Ñ Precautions on using this unit
• When you purchase optional accessories,
check with your KENWOOD dealer to make
sure that they work with your model and in
your area.
• You can select language to display menus,
audio file tags, etc. See User Interface Setup (P. 68).
• The Radio Data System or Radio Broadcast
Data System feature won’t work where the
service is not supported by any broadcasting
station.
• The unit may not function properly if the
connectors between the unit and front panel
are dirty. Detach the front panel and clean the
connector with a cotton swab gently, being
careful not to damage the connector.
Ñ Protecting the monitor
• To protect the monitor from damage, do not
operate the monitor using a ball point pen or
similar tool with the sharp tip.
Ñ Cleaning the unit
• If the faceplate of this unit is stained, wipe it
with a dry soft cloth such as a silicon cloth. If
the faceplate is stained badly, wipe the stain
off with a cloth moistened with neutral cleaner,
then wipe it again with a clean soft dry cloth.
NOTE
• Applying spray cleaner directly to the unit may
affect its mechanical parts. Wiping the faceplate
with a hard cloth or using a volatile liquid such
as thinner or alcohol may scratch the surface or
erase screened print.
Ñ Lens fogging
When you turn on the car heater in cold
weather, dew or condensation may form on
the lens in the disc player of the unit. Called
lens fogging, this condensation on the lens
may not allow discs to play. In such a situation,
remove the disc and wait for the condensation
to evaporate. If the unit still does not operate
normally after a while, consult your KENWOOD
dealer.
Ñ Precautions on handling discs
• Do not touch the recording surface of the disc.
• Do not stick tape etc. on the disc, or use a disc
with tape stuck on it.
• Do not use disc type accessories.
• Clean from the center of the disc and move
outward.
• When removing discs from this unit, pull them
out horizontally.
• If the disc center hole or outside rim has burrs,
use the disc only after removing the burrs with
a ballpoint pen etc.
• Discs that are not round cannot be used.
• 8-cm (3 inch) discs cannot be used.
• Discs with coloring on the recording surface or
discs that are dirty cannot be used.
4
Page 5
Before Use
• This unit can only play the CDs with
.
• This unit may not correctly play discs which do
not have the mark.
• You cannot play a disc that has not been
finalized. (For the finalization process see your
writing software, and your recorder instruction
manual.)
Ñ Acquiring GPS signal
The first time you turn on this unit, you must
wait while the system acquires satellite signals
for the first time. This process could take up
to several minutes. Make sure your vehicle
is outdoors in an open area away from tall
buildings and trees for fastest acquisition.
After the system acquires satellites for the first
time, it will acquire satellites quickly each time
thereafter.
Ñ Caution for Smartphone Users
Simultaneously running multiple applications
on your smartphone while screen sharing places
heavy demand on the microprocessor of the
phone, potentially affecting communication and
performance.
For best results while pairing with your Kenwood
receiver, please be sure to close any unused
applications by performing the following steps:
Android operating system example:
• Turn off WiFi in phone settings menu.
• Close all open applications before connecting
for in-car use. Hold the <Home> key and select
<Close all> to close all open applications.
• Clear RAM Memory of the Android phone
before connecting for in-car use. Hold the
<Home> key and select <Task Manager> then
select <RAM> then select <Clear memory> to
clear current memory processes.
How to read this manual
• The screens and panels shown in this manual are
examples used to provide clear explanations of the
operations.
For this reason, they may be different from the actual
screens or panels used, or some display patterns may
be different.
• Indication language: English indications are used
for the purpose of explanation. You can select the
indication language from the [SETUP] menu. See
User Interface Setup (P.68).
<Home> Key
5English
Page 6
Basic Operations
8
Basic Operations
Functions of the Buttons on the Front Panel
DDX9904S/ DDX9704S
1234567
DMX7704S
1294563
NOTE
• The panels shown in this guide are examples used to provide clear explanations of the operations. For this reason,
they may be different from the actual panels.
NumberNameMotion
Remote
1
Sensor
S, R
2
(Volume)
CAM• Switches view camera display on/off. (P. 64)
3
HOME• Displays the HOME screen (P.10).
4
MENU• Displays the popup menu screen.
5
6
• Receives the remote control signal.
• Adjusts volume.
The volume will go up until 15 when you keep pressing R.
– The camera whose view is displayed first changes according to the "Camera
Setup" setting and the shift lever position in the shift gate.
• Pressing for 1 second turns the power off. *
• When the power off, turns the power on.
* The function of the button when held varies depending on the "Manual Power OFF"
setting. (P. 69)
• Pressing for 1 second switches attenuation of the volume on/off. (DDX9904S/
DDX9704S only)
• Displays the APP (CarPlay/ Android Auto) screen.
• Pressing for 1 second displays the Voice Recognition screen (P.60).
6
Page 7
NumberNameMotion
G
7
Disc insert
8
slot
AT T• Switches attenuation of the volume on/off.
9
• Displays the Angle Adjust screen.
– DISC E JECT: Ejects the disc.
• When the panel is opened, pressing closes the panel.
• To forcibly eject the disc, press it for 2 seconds and touch [Yes ] after the message is
displayed.
• A slot to insert a disc media.
Turning on the Unit
The method of turning on is different depending on the model.
Press the [HOME] button.
1
Basic Operations
The unit is turned on.
● To turn off the unit:
Press the [HOME] button for 1 second.
1
NOTE
• If it is your first time turning the unit on after installation, it will be necessary to perform Initial setup (P. 8).
• The function of the button when held varies depending on the "Manual Power OFF" setting. (P. 69)
7English
Page 8
Basic Operations
Initial Settings
Initial setup
Perform this setup when you use this unit first
time.
Set each item as follows.
1
■ Language
Select the language used for the control
screen and setting items. Default is “American
English (en)”.
For detailed operation, see User Interface
Setup (P.68).
■ Clock
Sets the synchronization of the clock and
adjusts it.
For detailed operation, see Calendar/clock settings (P.9).
].
■ Display
Set the button illumination color.
If it is hard to see the image on the screen
even after adjusting the front panel angle,
adjust the viewing angle.
1Touch [Display.
2Touch [Key Color].
3Select the desired color.
4Touch [
5Touch [Viewing Angle].
6Select an angle
7Touch [
For detailed operation, see Display Setup
(P. 69).
■ Camera
Set the parameters for the camera.
1Touch [Camera].
2Set each item and touch [
For detailed operation, see Camera Setup
(P. 64).
■ OEM SETUP
This function requires a commercial adaptor.
Consult your KENWOOD dealer for details.
■ DEMO
Set the demonstration mode. Default is “ON”.
1Touch [DEMO] and set ON or OFF.
Touch [Finish].
2
].
].
].
NOTE
• These settings can be set from the SETUP menu.
See Setting Up (P.67).
8
Page 9
Basic Operations
Calendar/clock settings
Press the [MENU] button.
1
Popup menu appears.
Touch [SETUP].
2
SETUP Menu screen appears.
Touch [User Interface].
3
User Interface screen appears.
Set each item as follows.
4
Scroll the page to show the item.
Adjusting the volume
To adjust the volume (0 to 40),
Press [R] to increase, and press [S] to decrease.
Holding [R] increases the volume continuously
to level 15.
Monitor Angle Control
(DDX9904S/ DDX9704S)
You can adjust the position of the monitor.
Press the [G] button.
1
Angle Adjust screen appears.
Select a below number that represents
2
your desired angle setting.
Default is “0”.
■ Clock
GPS-SYNC (Default): Synchronizes the clock
time with the GPS.
Manual: Sets the clock manually.
■ Time Zone
Select the time zone.
■ Clock Adjust
If you select [Manual] for Clock, adjust the
date and time manually. (P. 68)
■ Off Position
You can store the current monitor angle as
the angle during power off. Touch [Memory]
when the desired angle is selected.
9English
Page 10
Basic Operations
Touch screen operations
To perform operations on the screen, you need
to touch, touch and hold, flick or swipe to
select an item, display setting menu screen or
to change the page, etc.
● Touch
Touch the screen gently to
select an item on the screen.
● Touch and hold
Touch the screen and keep
your finger in place until
the display changes or a
message is displayed.
● Flick
Slide your finger quickly
to the left or right on the
screen to change the page.
You can scroll the list screen
by flicking the screen up/
down.
● Swipe
Slide your finger up or down
on the screen to scroll the
screen.
HOME screen descriptions
Most functions can be performed from the
HOME screen.
123
4
5
67
• Displays the control screen of current source.
1
• Widget
2
– You can change the widget by touching
[
]/[ ] or flicking left or right on the
widget area.
– Touch the widget to display the detailed
screen.
• Page indication for widgets
3
• Current source information
4
• Displays the source selection screen. (P.11)
5
• Short-cut playback source icons (P. 12)
6
• Displays the Hands Free screen. (P. 59)
7
• When connecting as Apple CarPlay or
Android Auto, it works as a phone provided
in Apple CarPlay or Android Auto.
10
Display the HOME
Press the [HOME] button.
1
HOME screen appears.
Page 11
Basic Operations
Source selection screen
descriptions
You can display all playback sources and
options on the source selection screen.
1
35
• Changes the playback source.
1
For playback sources, see P.11.
2
• Changes the page. (Touch [ ]/[ ].)
You can also change the page by flicking left
or right on the screen.
• Returns to previous screen.
3
• Page indication
4
• Displays the SETUP Menu screen. (P. 67)
5
4
• Plays an iPod/iPhone. (P. 24)
• Plays files on a USB device. ( P.21)
2
• Switches to the Pandora. (P. 30)
• Switches to the Spotify. (P. 32)
• Switches to an external component
connected to the AV-IN input terminal.
(P. 66)
• Displays the Audio screen. (P. 72)
• Puts the unit in standby. (P. 12)
*1 When iPhone compatible with CarPlay is
connected, [Apple CarPlay] is displayed.
When an Android device compatible with
Android Auto is connected, [Android Auto] is
displayed.
2
*
DDX9904S/ DDX9704S only
• For sources and information displayed when
an ADS adapter is connected, see OEM Features Operation (P.66).
Select the playback source
Touch [] on the HOME screen.
1
From the screen, you can select the
following sources and functions.
• Switches to the Android Auto/ Apple
Car Play screen from the connected iPod
touch/iPhone/Android device.*1 (P. 27)
• Switches to the HD Radio broadcast.
(P. 34)
• Switches to the SiriusXM® satellite radio
broadcast. (P. 41)
• Plays a Bluetooth audio player. (P. 53)
• Plays a disc.*2 (P. 15)
11English
Page 12
Basic Operations
To select the playback source on the
HOME screen
The 3 items displayed on the source selection
screen as the large icons are shown on the
HOME screen.
You can change items displayed on this area
by customizing the source selection screen.
(P. 12)
To select the playback source on the
source control screen
Put the unit in standby
Touch [] on the HOME screen.
1
Touch [STANDBY].
2
Customize Short-cut buttons on
HOME screen
You can arrange the position of the source
icons as you like.
Touch [] on the HOME screen.
1
Touch and hold the icon which you want
2
to move to go into the customizing
mode.
Drag it where you want to move.
3
Display source selection buttons by touching
[ ]/[ ] or flicking left or right on the source
control screen, then select a playback source.
12
Page 13
Basic Operations
Source control screen
descriptions
There are some functions which can be
operated from most screens.
Indicators
1
234
Short-cut buttons
1
Connected Bluetooth device information.
: Lights up when quick charging battery
•
of the connected iPod/ iPhone/ Smartphone.
2
All sources icon
Displays all sources.
3
Secondary screen
• [
]/[ ] : The Secondary screen changes every
time you touch it. You can also change the
Secondary screen by flicking left or right on
the screen.
• Indicators: Displays the current source
condition and so on.
– AT T: The attenuator is active.
– DUAL: The dual zone function is on.
– MUTE: The mute function is active.
– LOUD: The loudness control function is on.
• Short-cut buttons: The source changes to the
one you have set as a short-cut. For the shortcut setting, refer to Customize Short-cut buttons on HOME screen (P.12).
4
[Û]
Touch to display the Hands Free screen. (P. 59)
When connecting as Apple CarPlay or Android
Auto, it works as a phone provided in Apple
CarPlay or Android Auto.
13English
Page 14
Basic Operations
Popup menu
Press the [MENU] button.
1
Popup menu appears.
Touch to display the popup menu.
2
5
The contents of the menu are as follows.
• Displays the Screen Adjustment screen.
(P. 67)
• Turns the display off. (P. 9)
• Displays the view camera. (P.64)
• Displays the SETUP Menu screen.
(P. 67)
• Displays the Audio Control Menu screen.
(P. 72)
• Displays the control screen of current
source. Icon feature differs depending on
the source.
• Close the popup menu.
5
• See HOME screen descriptions
6 7
(P. 10).
Turn off the screen
Select [Display OFF] on the pop-up
1
menu.
6
List screen
There are some common function keys in the
list screens of most sources.
612
345
1
7
Displays list type selection window.
2
Displays music/movie file list.
3
Text scroll
Scrolls the displayed text.
4
etc.
Keys with various functions are displayed here.
•
: Plays all tracks in the folder containing
the current track.
•
: Jump to the letter you entered
(alphabet search).
•
: Moves to the upper hierarchy.
5
[] / [] / [] / [] Page scroll
You can change the page to display more items
by pressing [
• [
]/[] : Displays the top or bottom page.
6
Return
]/[].
Returns to previous screen.
NOTE
• Buttons which cannot be activated from the list
screen are not displayed.
14
Page 15
Disc
Disc
(DDX9904S/ DDX9704S)
Playing a disc
Ñ Insert a disc
Press the [G] button.
1
Touch [DISC EJECT].
2
The panel opens.
Insert the disc into the slot.
3
The panel closes automatically.
The unit loads the disc and playback
starts.
DVD/ VCD Basic Operation
Most functions can be controlled from the
source control screen and playback screen.
NOTE
• Set the remote control mode switch to DVD
mode before starting operation for DVD and VCD,
see Switch the operation mode (P.80).
• The screen shot below is for DVD. It may be
different from the one for VCD.
When the operation buttons are not
1
displayed on the screen, touch the 7
area.
Control screen
1
2
3
Video screen
4
5
8
Ñ Eject a disc
Press the [G] button.
1
Touch [DISC EJECT].
2
When removing a disc, pull it horizontally.
Press the [G] button.
3
6
7
1
Information display
Displays the following information.
• Title #, Chapter #: DVD title and chapter
number display
• Track #/Scene #: VCD track or scene number
display. Scene # is displayed only when
Playback control (PBC) is on.
• Linear PCM, etc.: Audio format
• [Hide]: Hides the control screen.
6
15English
Page 16
Disc
• [] : Repeats the current content. Each time
you touch the key, repeat mode switches in
the following sequence;
DVD: Title repeat ( ), Chapter repeat
(
), Repeat off ( )
VCD (PBC On): Does not repeat
VCD (PBC Off ): Track repeat ( ), Repeat off
( )
2
Function panel
Touch on the left side of the screen to display
the function panel. Touch again to close the
panel. For details on the keys, see Function panel (P.16).
3
Play mode indicator/ Playing time
• D, B, I, etc.: Current play mode indicator
The meanings of each icon are as follows;
D (play), B (fast forward),
A (fast backward), I (stop),
R
(resume stop),
H (pause), (slow playback),
(slow reverse playback).
4
Function bar
• [E][F] : Searches the previous/next
content.
Touch and hold to fast forward or fast
backward. (It will be cancelled automatically
after about 50 seconds.)
• [DH] : Plays or pauses.
• [
] : Displays the Graphic Equalizer screen.
(P. 74)
5
Indicator Items
• IN: A disc is inserted.
White: A Disc is inside the unit.
Orange: Error at the disc player
VCD
• 1chLL/2chLL: Identifies the left audio output
of channel 1 or 2.
• 1chLR/2chLR: Identifies the monaural audio
output of channel 1 or 2.
• 1chRR/2chRR: Identifies the right audio
output of channel 1 or 2.
• 1chST/2chST: Identifies the stereo audio
output of channel 1 or 2.
• LL: Identifies the left audio output.
• LR: Identifies the monaural audio output.
• RR: Identifies the right audio output.
• ST: Identifies the stereo audio output.
• PBC: The PBC function is on.
• VER1: The VCD version is 1.
• VER2: The VCD version is 2.
16
6
Searching area
Touch to search the next/previous content.
7
Key display area
Touch to display the control screen.
8
MENU CTRL] (DVD only)
Touch to display the DVD-VIDEO disc menu
control screen. See DVD Disc Menu Operation (P. 19).
NOTE
• The control screen disappears when no operation
is done for 5 seconds.
• If you use a remote control, you can jump directly
to the desired image with entering the chapter
number, scene number, play time, etc. (P. 80).
Ñ Function panel
Touch on the left side of the screen.
1
DVDVCD
The functions of each key are as follows.
[I]
Stops playback. When touched twice, the disc is
played from the beginning when you play it the
next time.
[
] []
Fast forward or fast backward. Each time you
touch the key, the speed changes; 2 times, 8
times.
[
] or [] (DVD only)
Plays in slow motion forward or backward.
[SETUP] (DVD only)
Touch to display the DVD SETUP screen. See
DVD Setup (P.20).
[MENU CTRL] (DVD only)
Touch to display the DVD-VIDEO disc menu
control screen. See DVD Disc Menu Operation
(P. 19).
Page 17
Disc
[PBC] (VCD only)
Turn Playback control (PBC) on or off.
Audio] (VCD only)
Change the audio output channel.
Music CD/ Disc media Basic
Operation
Most functions can be controlled from the
source control screen and playback screen.
NOTE
• Set the remote controller mode switch to AUD
mode before starting operation for Music CD
and audio files, see Switch the operation mode (P. 80).
• In this manual, “Music CD” will be referred to as
the general CDs which include music tracks in.
“Disc media” will be referred to as CD/DVD disc
which includes audio or video files.
• The screen shot below is for disc media. It may be
different from the one for CD.
Control screen
1
7
4
3
Content list panel
4
1
[] / []
• [
] : Repeats the current track/folder. Each
time you touch the key, repeat mode switches
in the following sequence;
Track/ File repeat (
(Disc media only), Repeat all (
• [
] : Randomly plays all tracks in current
folder/disc. Each time you touch the key,
), Folder repeat ( )
)
random mode switches in the following
sequence;
Track random ( ) (Music CD only), Folder
random ( ) (Disc media only), Random off
( )
2
Track information
Displays the information of the current track/ file.
Only a file name and a folder name are displayed
if there is no tag information. (Disc media only)
3
Function bar
• [1] (Disc media only) : Searches file. For details
on search operation, see File search (P.18).
• [E][F] : Searches the previous/next
content.
Touch and hold to fast forward or fast
backward. (It will be cancelled automatically
after about 50 seconds.)
• [DH] : Plays or pauses.
• [
] : Displays the Graphic Equalizer screen.
(P. 74)
4
Function panel (Disc media only)
Touch on the left side of the screen to display
2
5
the function panel. Touch again to close the
panel.
• [
][] : Searches previous/next folder.
5
Content list
Touch on the right side of the screen to display
the Content list. Touch again to close the list.
6
6
Indicator Items
• IN: A disc is inserted.
White: A Disc is inside the unit.
Orange: Error at the disc player
• VIDEO: Identifies the video file.
• MUSIC: Identifies the music file.
8
7
Artwork (Disc media only)
/Play mode indicator/ Playing time
The jacket of the currently playing file is
displayed.
D, B, etc.: Current play mode indicator
• The meanings of each icon are as follows; D
(play), B (fast forward), A (fast backward),
H (pause).
8
Content list panel
Displays the playing list. When you touch a track/
file name on the list, playback will start.
17English
Page 18
Disc
Video screen
10
9
Searching file area (Video file only)
Touch to search the next/previous file.
10
Key display area (Video file only)
Touch to display the control screen.
Search Operation
(Disc media only)
99
You can search music or video files by the
following operations.
NOTE
• If you use a remote control, you can jump directly
to the desired track with entering the track
number. For details, see Direct search mode (P. 80).
Ñ File search
You can search a file according to hierarchy.
Touch [1].
1
Folder List screen appears.
Touch the desired folder.
2
When you touch a folder its contents are
displayed.
Touch desired item from the content list.
3
Playback starts.
18
NOTE
• For operations in the list screen, see List screen
(P. 14).
Page 19
Disc
DVD Disc Menu Operation
You can set up some items in the DVD-VIDEO
disc menu.
Touch illustrated area during playback.
1
Menu Control screen appears.
Perform desired operation as follows.
2
■ Displays the top menu
Touch [TOP].*
■ Displays the menu
Touch [MENU].*
■ Displays the previous menu
Touch [Return].*
■ Enters selected item
Touch [Enter].
■ Enables direct operation
Touch [Highlight] to enter the highlight
control mode (P. 19).
■ Moves the cursor
Touch [R], [S], [C], [D].
■ Switches the subtitle language
Touch [Subtitle]. Each time you touch this
key, language is switched.
■ Switches the audio language
Touch [Audio]. Each time you touch this key,
language is switched.
■ Switches the picture angle
Touch [Angle]. Each time you touch this key,
picture angle is switched.
* These keys may not function depending on
the disc.
Ñ Highlight control
Highlight control lets you control the DVD
menu by touching the menu key directly on
the screen.
Touch [Highlight] in the Menu Control
1
screen.
Touch desired item on the screen.
2
NOTE
• The highlight control is cleared automatically if
you do not operate for a constant time.
19English
Page 20
Disc
DVD Setup
You can set up the DVD playback functions.
Touch illustrated area during playback.
1
Touch on the left side of the screen.
2
Touch [SETUP].
DVD SETUP screen appears.
Set each item as follows.
3
■ Screen Ratio
Sets the screen display mode.
16:9 (Default): Displays wide pictures.
4:3 LB: Displays wide pictures in the Letter
Box format (having black stripes at the top
and bottom of screen).
4:3 PS: Displays wide pictures in the Pan &
Scan format (showing pictures cut at the
right and left ends).
Ñ Language setup
This setting is for the language used in the
menu, subtitle, and voice.
For language code, refer to DVD Language
Codes (P.96).
Sets the entered language and returns to
the DVD Setting screen.
■ [
Menu Language] / [Subtitle Language]
/ [Audio Language]
See Language setup (P.20).
■ Dynamic Range Control
Sets the dynamic range.
Wide: The dynamic range is wide.
Normal: The dynamic range is normal.
Dialog (Default): Makes the total sound
volume larger than other modes. This is
effective only when you are using Dolby
Digital software.
20
NOTE
• To set the DVD’s original language for audio
language, touch [Original].
Page 21
USB
USB
Connecting a USB device
Connect the USB device with the USB
1
cable. (P. 89)
Press the [HOME] button.
2
Touch .
3
Touch [USB]. (P.11)
4
Ñ Disconnect the USB device
Press the [HOME] button.
1
Touch a source other than [USB].
2
Detach the USB device.
3
Ñ Usable USB device
You can use a mass-storage-class USB device on
this unit.
The word “USB device” appearing in this manual
indicates a flash memory device.
● About file system
The file system should be the one of the
following.
• FAT16• FAT32• exFAT• NTFS
NOTE
• Install the USB device in the place where it will
not affect safe driving.
• You cannot connect a USB device via a USB hub
and Multi Card Reader.
• Take backups of the audio files used with this
unit. The files can be erased depending on the
operating conditions of the USB device.
We shall have no compensation for any damage
arising from any erased data.
USB Basic Operation
Most functions can be controlled from the
source control screen and playback screen.
NOTE
• Set the remote controller mode switch to AUD
mode before starting operation, see Switch the operation mode (P.80).
Control screen
1
7
4
3
Content list panel
4
1
[] / []
• [
] : Repeats the current track/folder. Each
time you touch the key, repeat mode switches
in the following sequence;
File repeat ( ), Folder repeat ( ), Repeat
all ( )
• [
] : Randomly plays all tracks in current
folder. Each time you touch the key, random
mode switches in the following sequence;
File random ( ), Random off ( )
• When a high-resolution source is played, its
format information is displayed.
2
Track information
Displays the information of the current file.
Only a file name and a folder name are displayed
if there is no tag information.
2
5
6
8
21English
Page 22
USB
3
[Function bar
• 1] : Searches track/file. For details on search
operation, see Search Operation (P.23).
• E][F] : Searches the previous/next track/
file.
Touch and hold to fast forward or fast
backward. (It will be cancelled automatically
after about 50 seconds.)
• [DH] : Plays or pauses.
• [
] : Displays the Graphic Equalizer screen.
(P. 74)
4
Function panel
Touch on the left side of the screen to display
the function panel. Touch again to close the
panel.
• [
][] : Searches previous/next folder.
• [USB DEVICE CHANGE]
Switches to another USB device when two USB
devices are connected.
5
Content list
Touch on the right side of the screen to display
the Content list. Touch again to close the list.
6
Indicator Items
• VIDEO: Identifies the video file.
• MUSIC: Identifies the music file.
7
Artwork/ Play mode indicator/ Playing
time
The jacket of the currently playing file is
displayed.
• D, B, etc.: Current play mode indicator
The meanings of each icon are as follows;
D (play), B (fast forward), A (fast
backward), H (pause).
8
Content list panel
Displays the playing list. When you touch a track/
file name on the list, playback will start.
Video screen
10
9
Searching file area (Video file only)
Touch to search the next/previous file.
10
Key display area (Video file only)
Touch to display the control screen.
99
22
Page 23
USB
Search Operation
You can search music or video files by the
following operations.
Touch [1].
1
Touch [S].
2
Select the list type.
3
NOTE
• For operations in the list screen, see List screen
(P. 14).
Ñ Category search
You can search a file by selecting category.
Touch [Category List].
1
Select whether you search by audio files
2
or video files .
Touch the desired category.
3
Ñ Link search
You can search a file of same artist/album/
genre as the current track.
Touch [Link Search].
1
Touch the desired tag type. You can select
2
from artist, album and genre.
The list corresponding to your selection
appears.
Touch desired item from the content list.
3
Ñ Folder search
You can search a file according to hierarchy.
Touch [Folder List].
1
The list corresponding to your selection
appears.
Touch to select desired item in the list.
4
Repeat this step until you find the desired
file.
Touch the desired folder.
2
When you touch a folder its contents are
displayed.
Touch to select desired item in the list.
3
Repeat this step until you find the desired
file.
23English
Page 24
iPod/iPhone
iPod/iPhone
Preparation
Ñ Connectable iPod/iPhone
The following models can be connected to
this unit.
Made for
• iPhone 6s Plus
• iPhone 6s
• iPhone 6 Plus
• iPhone 6
• iPhone 5s
• iPhone 5c
• iPhone 5
• iPod touch (6th generation)
• iPod touch (5th generation)
NOTE
• Latest compatible list of iPod/iPhone. For details,
see www.kenwood.com/cs/ce/ipod/.
• By connecting your iPod/iPhone to this unit with
an optional accessory iPod connection cable
KCA-iP103, you can supply power to your iPod/
iPhone as well as charge it while playing music.
However, the power of this unit must be on.
• If you start playback after connecting the iPod,
the music that has been played by the iPod is
played first.
Ñ Connect iPod/iPhone
Wired connection
Preparation
• Connect an iPod/iPhone with the KCA-iP103
(optional accessory) while CarPlay is not
connected.
• With a CarPlay-capable iPhone, turn off CarPlay
by operating the iPhone at functional setup
before connecting iPhone. For details of the
setup method, contact the manufacturer of the
terminal.
• Plug the iPod/iPhone into the gray USB terminal
with the KCA-iP103 (optional accessory).
• Only one iPod/iPhone can be connected.
Connect the iPod/iPhone using KCA-
1
iP103. (P. 90)
Press the [HOME] button.
2
Touch [].
3
Touch [iPod]. (P. 11)
4
● To disconnect the iPod/iPhone connected
with the cable:
Detach the iPod/iPhone.
1
Bluetooth connection
Pair the iPhone through Bluetooth.
Preparation
• To connect an iPhone via Bluetooth, register it as
the Bluetooth device and do the profile setting of
the connection beforehand. See Register from
the Bluetooth unit (P.54) and Connect the
Bluetooth unit (P.56).
• Connect an iPhone on Bluetooth while CarPlay
and an iPod/iPhone are not connected on USB.
24
Page 25
iPod/iPhone
iPod/iPhone Basic Operation
NOTE
• Set the remote controller mode switch to AUD
mode before starting operation, see Switch the operation mode (P.80).
Control screen
2
3
Content list panel
6
1
[] / []
• [
] : Repeats the current track/album. Each
time you touch the key, repeat mode switches
in the following sequence;
Song repeat (
• [
] : Randomly plays all tracks in current
album. Each time you touch the key, random
mode switches in the following sequence;
Song random ( ), Album random ( ),
Random off ( )
2
Track information
• Displays the information of the current file.
• Touch to display the category list screen. See
Category search (P.26).
), All songs repeat ( )
3
[Function bar
• 1] : Searches track/file. For details on search
operation, see Search Operation (P.26).
• E][F] : Searches the previous/next track/
file. Touch and hold to fast forward or fast
backward. (It will be cancelled automatically
after about 50 seconds.)
• [DH] : Plays or pauses.
• [
] : Displays the Graphic Equalizer screen.
(P. 74)
4
4
5
1
7
Content list
Touch on the right side of the screen to display
the Content list. Touch again to close the list.
5
Indicator Items
• MUSIC: Identifies the music file.
6
Artwork/ Play mode indicator/ Playing
time
The jacket of the currently playing file is
displayed.
• D, B, etc.: Current play mode indicator
The meanings of each icon are as follows;
D (play), B (fast forward),
A (fast backward), H (pause).
7
Content list panel
Displays the playing list. When you touch a track/
file name on the list, playback will start.
25English
Page 26
iPod/iPhone
Search Operation
You can search music files by the following
operations.
Touch [1].
1
Touch [S].
2
Select the list type.
3
NOTE
• For operations in the list screen, see List screen
(P. 14).
Ñ Category search
You can search a file by selecting category.
Touch [Category List].
1
Touch the desired category.
2
Ñ Link search
You can search a file of same artist/album/
genre/composer as the current track.
Touch [Link Search].
1
Touch the desired tag type. You can select
2
from artist, album, genre and composer.
The list corresponding to your selection
appears.
Touch desired item from the content list.
3
The list corresponding to your selection
appears.
Touch to select desired item in the list.
3
Repeat this step until you find the desired
file.
26
Page 27
APPS—Android Auto™/Apple CarPlay
APPS—Android Auto™/Apple CarPlay
Apple CarPlay Operation
CarPlay is a smarter, safer way to use your
iPhone in the car. CarPlay takes the things
you want to do with iPhone while driving and
displays them on the screen of the product.
You can get directions, make calls, send and
receive messages, and listen to the music
from iPhone while driving. You can also use
Siri voice control to make it easier to operate
iPhone.
For details about CarPlay, visit https://ssl.
apple.com/ios/carplay/.
Compatible iPhone devices
You can use CarPlay with the following iPhone
models.
• iPhone 6s Plus
• iPhone 6s
• iPhone 6 Plus
• iPhone 6
• iPhone 5s
• iPhone 5c
• iPhone 5
Ñ Preparation
Connect iPhone using KCA-iP103 via USB
1
(Black) terminal. (P. 90)
When iPhone compatible with CarPlay is
connected to the USB (Black) terminal, the
Bluetooth smartphone currently connected
is disconnected.
Unlock your iPhone.
2
Ñ Operation buttons and
available Apps on the home
screen of CarPlay
You can use the Apps of the connected iPhone.
The items displayed and the language used
on the screen differ among the connected
devices.
To enter CarPlay mode, touch [Apple CarPlay]
icon in the source selection screen. (P. 11)
2
1
1
[]
• Displays the home screen of CarPlay.
• Touch and hold to activates Siri.
2
Application buttons
Starts the application.
3
[HOME]
Exits the CarPlay screen and displays the Home
screen.
To exit the CarPlay screen
Press the [HOME] button.
1
3
27English
Page 28
APPS—Android Auto™/Apple CarPlay
Ñ Use Siri
You can activate Siri.
Press the [] button for 1 second.
1
Press for 1 second
Talk to Siri.
2
To deactivate
Press the [] button.
1
Ñ Switch to the Apple CarPlay
screen while listening to
another source
Press the [] button.
1
NOTE
• If sound is output using Apple CarPlay when the
Apple CarPlay screen is displayed, the source is
switched to Apple CarPlay.
Android Auto™ Operation
Android Auto enables you to use functions of
your Android device convenient for driving.
You can easily access route guidance, make
calls, listen to music, and access convenient
functions on the Android device while driving.
For details about Android Auto, visit https://
www.android.com/auto/ and https://support.
google.com/androidauto.
Compatible Android devices
You can use Android Auto with Android
devices of Android version 5.0 (Lollipop) or
later.
NOTE
• Android Auto may not be available on all devices
and is not available in all countries or regions.
Ñ Preparation
Connect an Android device via USB
1
terminal. (P. 90)
To use the hands-free function, connect the
Android device via Bluetooth.
When an Android device compatible
with Android Auto is connected to the
USB terminal, the device is connected via
Bluetooth automatically, and the Bluetooth
smartphone currently connected is
disconnected.
Unlock your Android device.
2
28
Page 29
APPS—Android Auto™/Apple CarPlay
Ñ Operation buttons and
available Apps on the Android
Auto screen
You can perform the operations of the Apps of
the connected Android device.
The items displayed on the screen differ
among the connected Android devices.
To enter Android Auto mode, touch [Android Auto] icon in the source selection screen.
(P. 11)
1
1
Application/information buttons
Starts the application or displays information.
To exit the Android Auto screen
Press the [HOME] button.
1
Ñ Using voice control
Press the [] button for 1 second.
1
Ñ Switch to the Android Auto
screen while listening to
another source
Press the [] button.
1
NOTE
• If sound is output using Android Auto when the
Android Auto screen is displayed, the source is
switched to Android Auto.
Press for 1 second
To cancel
Press the [] button.
1
29English
Page 30
APPS—Android Auto™/Apple CarPlay
Pandora® Operation
You can listen to the Pandora® on this unit
by controlling the application installed in the
iPhone or Bluetooth device.
To enter Pandora source, touch [Pandora] icon
in the source selection screen. (P. 11)
Preparation
• Install the latest version of the Pandora®
application on your iPhone, Android or BlackBerry.
iPhone: Search for "Pandora" in the Apple App
Store to find and install the most current version.
Android: Visit the Google play and search for
Pandora to install.
BlackBerry: Visit www.pandora.com from the
built in browser to download the Pandora
application.
• iPhones are connected on either USB or
Bluetooth.
• Android or BlackBerry devices are connected on
Bluetooth.
• To connect a smartphone via Bluetooth, register
it as the Bluetooth device and do the App (SPP)
profile setting of the connection beforehand. See
Register from the Bluetooth unit (P.54) and
Connect the Bluetooth unit (P.56).
1
2
1
Artwork/ Playing time
• The picture data is displayed if available from
current content.
• For confirmation of play time.
2
Function bar
] : Searches for a station. For details on
• [
searching, see Station list screen (P.30).
• [
] (Thumbs down) : Thumbs down to the
current contents and skip to the next contents.
• [
] (Thumbs up) : Registers the current
contents as favorite content.
• [D] , [H] : Plays or pauses the content of the
current station.
• [F] : Skips the current song.
(Note this function is disabled when the
Pandora skip limitation is exceeded.)
• [
] (Bookmark Song) : Bookmarks a song in
the current contents.
• [
] : Creates a new station. See Creates a
new station (P.31).
• [
] : Displays the Graphic Equalizer screen.
(P. 74)
3
Content information
Displays the information of the current content
being played.
Ñ Station list screen
You can perform the following functions from
this screen.
Touch [ ].
1
Station List screen appears.
3
■ Selects the station
Touch the station name in the list.
■ Sort the list by registered date
Touch [By Recent]. The list is sorted to begin
with the last registered station.
■ Sort the list in alphabetical order
Touch [By Name]. You can select the desired
letter from the list which corresponds to the
station name to help narrow the search.
NOTE
• You can operate Pandora by using the remote
control. However, only playing, pausing, and
skipping are available.
30
Page 31
APPS—Android Auto™/Apple CarPlay
Ñ Creates a new station
Touch [ ].
1
Touch desired item.
2
■ Create station from artist
Creates a new station based on an artist
being played.
■ Create station from track
Creates a new station based on a song being
played.
■ Create station from genre
Displays the genre list screen.
Genre list screen
Touch [Create station from genre].
1
About Pandora®
iPhone or iPod touch
• Install the latest version of the Pandora
application on your iPhone or iPod touch. (Search
for “Pandora” in the Apple App Store to find and
install the most recent version.)
Android™
• Visit the Google play and search for Pandora to
install.
BlackBerry®
• Visit www.pandora.com from the built in browser
to download the Pandora application.
• Bluetooth must be built in and the following
profiles must be supported.
- SPP (Serial Port Profile)
- A2DP (Advanced Audio Distribution Profile)
NOTE
• In the application on your device, log in and
create an account with Pandora.
(If you are not already a registered user, an
account can also be created at www.pandora.
com.)
• Establish an Internet connection.
• Pandora is only available in certain countries.
Please visit http://www.pandora.com/legal for
more information.
• Because Pandora® is a third-party service, the
specifications are subject to change without
prior notice. Accordingly, compatibility may
be impaired or some or all of the services may
become unavailable.
• Some functions of Pandora® cannot be operated
from this unit.
• For issues using the application, please contact
Pandora® at pandora-support@pandora.com.
The selected genre is created as a new
2
station.
31English
Page 32
APPS—Android Auto™/Apple CarPlay
Spotify Operation
You can listen to the Spotify on this unit by
controlling the application installed in the
iPhone or Android.
To enter Spotify source, touch [Spotify] icon in
the source selection screen. (P. 11)
Preparation
• Install the latest version of the Spotify application
"Spotify" on your iPhone or Android.
iPhone: Search for "Spotify" in the Apple App
Store to find and install the most current version.
Android: Search for "Spotify" in Google play to
find and install the most current version.
• iPhones are connected on either USB or
Bluetooth.
• Android devices are connected on Bluetooth.
• To connect a smartphone via Bluetooth, register
it as the Bluetooth device and do the App (SPP)
profile setting of the connection beforehand. See
Register from the Bluetooth unit (P.54) and
Connect the Bluetooth unit (P.56).
1
2
1
Artwork/ Playing time
• The picture data is displayed if available from
current content.
• For confirmation of play time.
2
Function bar
] : Displays the Menu screen
• [
• [
] : New radio station that relates to the
artist of the currently playing song is selected
and playback starts.
• [
] , [] : Skips the current song.
• [
] , [] : Plays or pauses the content of the
current station.
] : Saves currently playing song to My
• [
Music.
• [
] : Displays the Graphic Equalizer screen.
(P. 74)
3
Content information
Displays the information of the current content
being played.
4
[ ] / [ ] / [ ] / [ ]
• [
] : Thumbs down to the current contents
and skip to the next contents.
• [
] : Registers the current contents as favorite
content.
• [
] : Repeats the current song.
• [
] : Randomly plays all song in current
playlist.
Ñ Selecting a track
Touch [ ].
1
Menu screen appears.
Select the list type, then select a desired
2
item.
4
3
■ Selects the category and station
Touch the category and station name in the
list.
To p]
■ [
Returns to the first hierarchy of the list.
Up]
■ [
Returns to the previous list.
32
Page 33
About Spotify®
iPhone or iPod touch
• Install the latest version of the Spotify application
on your iPhone or iPod touch. (Search for “Spotify”
in the Apple App Store to find and install the
most recent version.)
Android™
• Visit Google play and search for “Spotify” to install.
Note
• Ensure you are logged in to your smartphone
application. If you do not have an Spotify account,
you can create one for free from your smartphone
or at www.spotify.com.
• Because Spotify is a third-party service, the
specifications are subject to change without
prior notice. Accordingly, compatibility may
be impaired or some or all of the services may
become unavailable.
• Some functions of Spotify cannot be operated
from this unit.
• For issues using the application, contact Spotify at
www.spotify.com.
• Establish an Internet connection.
APPS—Android Auto™/Apple CarPlay
33English
Page 34
HD Radio™ Tuner
HD Radio™ Tuner
HD Radio Tuner Basic
Operation
Most functions can be controlled from the
source control screen.
To enter HD Radio source, touch [HD Radio]
icon in the source selection screen. (P. 11)
NOTE
• Set the remote control mode switch to AUD
mode before starting operation, see Switch the operation mode (P.80).
• HD Radio broadcasting is for North American
sales area only.
• The screen shot below is for tuner. It may be
different from the one for HD Radio broadcasting.
Control screen
2
3
6
4
Preset list screen
7
8
10
1
Indicator display
While receiving an HD Radio station, it lights
with orange when the audio is digital and lights
with gray when it is analog. While receiving an
analog station, it is off.
2
Information display
Displays the information of the current station:
Frequency and Channel
Touching [
Content A, Content B and Content C.
Content A: Station name, Song Title, Artist Name
Content B: Station Message, Radio Text
Content C: PTY Genre, Album Name
3
[AUTO1] / [AUTO2] / [MANUAL]
Switches the seek mode in the following
sequence; [AUTO1], [AUTO2], [MANUAL].
• [AUTO1]: Tunes in a station with good
reception automatically.
• [AUTO2]: Tunes in stations in memory one
after another.
• [MANUAL]: Switches to the next frequency
manually.
4
Function bar
• [E][F] : Tunes in a station. The method of
frequency switching can be changed (see 3
5
1
9
in table).
• [CHS][CHR] : Selects a channel.
• [1] : Display the Channel List screen. See
Channel search (P.37).
• [
See Bookmark list (P.39).
• [
(P. 74)
5
Preset key
Recalls the memorized station or channel.
• Touch on the right side of the screen to display
the Preset list. Touch again to close the list.
6
Function panel
Touch on the left side of the screen to display
the function panel. Touch again to close the
panel. For details on the keys, see Function panel (P.35).
7
Picture
The picture data or station Logo data is
displayed if available from current content.
8
[FM][AM]
Switches the band.
] allows you to switch between
] : Display a list of registered bookmarks.
] : Displays the Graphic Equalizer screen.
34
Page 35
HD Radio™ Tuner
9
Preset list
Recalls the memorized station or channel.
When touched for 2 seconds, stores the current
receiving station or channel in memory.
10
Indicator Items
• MC: A multicast digital broadcast is being
received.
• ANALOG: An analog broadcast is being
received.
• DIGITAL: A digital broadcast is being received.
• ST: A stereo broadcast is being received.
• EA:
White: Emergency Alert is on.
No light: Emergency Alert is off.
Orange: Interrupting or in snooze/ignore
state.
Ñ Function panel
Touch on the left side of the screen.
1
The functions of each key are as follows.
[10key Direct]
Display the direct station/ channel search screen.
For details, see Direct search (P.37).
[AME]
Presets stations automatically. For details, see
Auto memory (P.36).
[RCV]
Change the HD Radio reception mode. For
details, see Receive Mode (P.36).
[PTY] (FM only)
Searches a program by setting program type. For
details, see Search by program type (P.38).
[
]
Stores the information about the song being
received. See Bookmark (P.38).
[Emergency Alerts]
Turn on or off the alert message. See Alert
Message (P.40).
[Alert Message Log]
Displays the alert message received. See Alert
Message (P.40).
• Adjacent to traditional main stations are
HD2/HD3 Channels, providing new original
programming on the FM dial
• A music & product discovery feature that
enables users to store information about
content on the radio, and can deliver
interactive information via QR codes
• Crystal clear, CD-like digital audio quality to
consumers; eliminates background noise
• Provides song name, artist, station ID, and
other relevant data to enrich the listening
experience
• Visual images, such as album art of over-the-air
broadcasts from HD Radio stations
• Delivers critical and life-saving messages to the
public during emergency situations
35English
Page 36
HD Radio™ Tuner
Receive Mode
You can set the radio broadcasts receive mode.
Touch on the left side of the screen.
1
Touch [RCV].
Select a receive mode.
2
■ [Auto]
Switch between digital and analog audio
automatically.
■ [Digital]
Select this to tune to digital audio only.
■ [Analog]
Select this to tune to analog audio only.
Memory Operation
Ñ Auto memory
You can store stations with good reception in
memory automatically.
Touch desired band key.
1
Touch on the left side of the screen.
2
Touch [AME].
Touch [Yes ].
3
36
Auto memory starts.
Ñ Manual memory
You can store the current receiving station or
channel in memory.
Select a station or channel you wish to
1
store in memory.
Touch [FM#] (#:1-15) or [AM#] (#:1-5)
2
in which you want to store the station
or channel for 2 seconds until a beep
sounds.
Page 37
HD Radio™ Tuner
Selecting Operation
Ñ Preset select
You can list and select memorized station or
channel.
Touch on the right side of the screen.
1
Select a station or channel from the list.
Ñ Direct search
You can tune in by entering the desired
frequency or channel number.
Touch on the left side of the screen.
1
Touch [10key Direct].
Ñ Channel search
You can specify the desired channel.
Touch [1].
1
Select the desired content from the list.
2
NOTE
• Touch [Info Change] in the channel list. Select
the sequence of the list (Song title, artist name,
album name).
Select the search method.
2
Enter the frequency or channel number.
3
Touch [Enter].
4
NOTE
• To clear the number you entered, touch [BS].
37English
Page 38
HD Radio™ Tuner
Ñ Search by program type
(FM only)
You can tune to a station with a specific
program type when listening to FM.
Touch on the left side of the screen.
1
Touch [PTY].
TUNER PTY Mode screen appears.
Select a program type from the list.
2
Touch [Search].
3
Bookmark
Stores tag information (title, artist, album,
URL, and description) about the song you are
listening to now.
Detailed information and QR codes can
be displayed according to the stored tag
information.
Ñ Bookmark registration
Touch on the left side of the screen.
1
Touch [
NOTE
• Up to 100 bookmarks can be registered to this
unit.
].
Registers a bookmark.
You can search a station of the selected
program type.
38
Page 39
HD Radio™ Tuner
Ñ Bookmark list
Displaying a list of registered bookmarks and
detailed information and QR code of the song.
Touch [].
1
Select the desired bookmark from the list.
2
The bookmark information appears.
Bookmark delete
Deleting a bookmark.
Touch [Delete].
1
Select the bookmark to delete from the
2
list.
■ [þ All]
Select all bookmarks.
■ [¨ All]
Erases all check marks.
Touch [Delete].
3
Confirmation message appears.
Touch [Yes ].
4
Deletes all the selected bookmark(s).
■ [ Delete]
Deletes the bookmarks being displayed.
39English
Page 40
HD Radio™ Tuner
Alert Message
This function is to receive alert messages. First,
you need to turn on the “Emergency Alerts”.
(P. 35)
Ñ When an Alert Message comes
[Snooze]
The alert message is erased. Same alert message
cannot be displayed for next 10 minutes.
[Ignore]
The alert message is erased. Same alert message
cannot be displayed for next 12 hours.
Ñ Display of the received Alert
Message
You can read the received alert message
afterward.
Touch on the left side of the screen.
1
Touch [Alert Message Log].
Select the desired Alert Message from
2
the list.
The Alert Message appears.
40
Touch [Close].
3
Page 41
SiriusXM®
SiriusXM®
SiriusXM® Basic Operation
Only SiriusXM® brings you more of what you
love to listen to, all in one place. Get over 140
channels, including commercial-free music
plus the best sports, news, talk, comedy
and entertainment. Welcome to the world
of satellite radio. A SiriusXM Vehicle Tuner
and Subscription are required. For more
information, visit www.siriusxm.com.
To enter SiriusXM source, touch [SiriusXM]
icon in the source selection screen. (P. 11)
Activating subscription
• Check your Radio ID.
The SiriusXM Satellite Radio ID is required for
activation and can be found by tuning to Channel
0 as well as on the label found on the SiriusXM
Connect tuner and its packaging.
The Radio ID does not include the letters I, O, S
or F.
• Activate the SiriusXM Connect Vehicle Tuner
using one of the two methods below:
– For users in the U.S.A.
Online: Visit www.siriusxm.com/activatenow
Phone: Call SiriusXM Listener Care at 1-866635-2349
– For users in Canada:
Online: Visit www.siriusxm.ca/activatexm
Phone: Call XM customer Care at 1-877-4389677
NOTE
• Set the remote control mode switch to AUD
mode before starting operation, see Switch the operation mode (P.80).
• To use SiriusXM® Satellite Radio, the optional
accessory is necessary.
Control screen
2
3
6
5
4
Preset list screen
1
7
8
1
Indicator display
Displays the “M ix” (TuneMix™), “Scan”
(TuneScan™),
(SportsFlash™) indicator and the received
signal strength of the SiriusXM tuner.
2
Information display
Displays the information of the current channel:
Channel Name
Touching [
Content A and Content B.
Content A: Artist Name, Song Title, Content Info
Content B: Category Name, Channel Description,
Similar Channels
[
] : Touch for 2 seconds to registers the artist
of the current song as a Content Alert.
[
] : Touch for 2 seconds to registers the
current song as a Content Alert.
For details, see Content Alerts (P.47).
3
[SEEK]
Switches the seek mode in the following
sequence; [SEEK1], [SEEK2].
SEEK1: Tunes channels one after the other.
SEEK2: Selects channels in preset (memory) one
after the other.
(Traffic&Weather),
] allows you to switch between
41English
Page 42
SiriusXM®
4
Function bar
• [1] : Display the Category search screen. For
details on search operation, see Category/Channel search (P.44).
• DH] : Plays or pauses. See Replay (P.45).
• [CHS][CHR] : Selects a channel.
• [
] : Displays the Graphic Equalizer screen.
(P. 74)
5
Preset key
Recalls the memorized channel.
Touch on the right side of the screen to display
the Preset list. Touch again to close the list.
6
Function panel
Touch on the left side of the screen to display
the function panel. Touch again to close the
panel. For details on the keys, see Function panel (P.42).
7
Information display
Displays the following information.
SXM#: Band display
P#: Preset number
#CH: Channel display
Logo: Display album artwork for most SiriusXM
music channels
8
[Preset list
Recalls the memorized channel.
When touched for 2 seconds, stores the current
receiving channel in memory.
Ñ Function panel
Touch on the left side of the screen.
1
The functions of each key are as follows.
[Direct Channel]
Touch and enter the desired number. For
details, see Direct search (P.44).
[SETUP]
Touch to display the SiriusXM SETUP screen.
For details, see SiriusXM Setup (P.48).
[Band]
Switches the band. (SXM1/ SXM2/ SXM3/
SXM4)
[Replay]/ [Live]
Turns the replay mode on or off. See Replay
(P. 45).
[Traffic & Weather]
For SXV300 *
Traffic & Weather Now™ allows you to access
the latest report whenever you want to hear
it. Select your city at the set up menu Select a City for Traffic & Weather (P.52) and
press the [Traffic & Weather] button to
check the latest report. It will start from the
beginning.
•
•
•
•
For SXV200 or SXV100 *
Turns the Traffic & Weather Jump function
on or off.
•
•
•
1
(White) : Played already.
(Green) : New information arrived.
(Purple) : Playing.
(Gray) : No information.
2
(White) : Function on.
(Purple) : Playing.
(Gray) : Function off.
42
Page 43
SiriusXM®
[TuneScan]*
[TuneMix]*
[SportsFlash]*
1
Compatible with SXV300 or later tuner
*
models. It may take a few minutes after power
on to get the first full report for your city.
Traffic channels are not available in Canada.
2
*
When SXV200 or SXV100 is connected with
this unit.
3
*
Compatible with SXV200 or later tuner models.
4
*
Compatible with SXV300 or later tuner models.
3
Hear a few seconds of the songs from each
of the SmartFavorite music channels on
the current preset band. See TuneScan™ (P. 46).
4
When you turn it ON, the preset channels
on P1-P6 are shuffled to provide a playback
which is a blend of songs from your favorite
channels. See TuneMix™ (P.45).
4
Displays during SportFlash™. To cancel
the SportFlash interruption and return
to the previous channel, touch it. See
SportsFlash™ (P.47) and SportsFlash™
setup (P.51).
Storing Channels in Preset
Memory
You can store the current channel in memory.
Tune to a channel you wish to store in
1
memory.
Touch on the right side of the screen.
2
Touch and hold for 2 seconds (until you
3
hear a beep) the preset number [SXM(1-
4) P(1-6)] in which you want to store the
channel.
Preset select
You can list and select memorized station or
channel.
To select from the preset list
Touch on the right side of the screen.
1
Select a channel from the list.
43English
Page 44
SiriusXM®
Direct search
You can tune to a channel directly.
Touch on the left side of the screen.
1
Touch [Direct Channel].
Enter the channel number and touch
2
[Enter].
NOTE
• To clear the number you entered, touch [BS].
Category/Channel search
You can specify the desired category and
select a channel.
Touch [1].
1
Select a category.
2
Channel list appears.
Select the desired content from the list.
3
44
NOTE
• All the channels in the selected category appear.
• Touching [All-Channels] displays all the
channels.
• Touch [Info Change] in the channel list. Select
the sequence of list as follows;
Channel name, artist name, song title, category
name, content info
• Categories which have the prefix “Featured - “ are
Featured Favorites.
• Featured Favorites are groups of channels that
are created by the SiriusXM Programming
department allowing you to discover new
channels. Featured Favorite channels are dynamic
and can change often, allowing you to discover
new channels.
Page 45
SiriusXM®
Replay
You can replay the last 60 minutes of the
current channel.
Touch [L] or [Replay] on the function
1
panel.
■ [E] [F]
Press to skip to the previous/next track.
Press and hold to rewind or fast forward. (It
will be cancelled automatically after about
50 seconds.)
■ [DH]
Plays or pauses.
■ [CHS] [CHR]
Tune in a channel.
■ Replay time bar/ Play mode indicator
Display recorded capacity and playback
position.
D, B, etc.: Current play mode indicator
■ [1]
Display a list of recorded data on a program
basis.
Touch [1] to display an Instant Replay list.
2
To return to live music/content
Touch on the left side of the screen.
1
Touch [Live].
2
TuneMix™
TuneMix™ plays a unique blend of songs from
your Preset music channels from the current
SiriusXM Preset Band, allowing you to build a
custom channel from as few as two to as many
as 6 music channels. You can even skip songs
you don’t want to hear.
Touch on the left side of the screen.
Touch on the left side of the screen.
1
Touch [TuneMix] to set ON or OFF.
NOTE
• Compatible with SXV300 or later tuner models.
SmartFavorites, TuneStart™
Preset channels 1 through 6 of the current
band are SmartFavorites channels.
The SiriusXM Vehicle Tuner automatically
buffers the broadcast audio content of the
SmartFavorites channels in the background.
■ Instant Replay List
Touching this plays back the displayed
program.
■ [Info Change]
Touch [Info Change]. Select the sequence of
the list as follows;
Artist name, Song title, Category name, and
Content info
You can rewind and replay up to 30 minutes of
any of the missed news, talk, sports or music
content when you tune to a SmartFavorites
channel. (see Replay (P.45))
When tuning from a SmartFavorites channel,
songs will play from the beginning of each
track (TuneStart™). You can enable/disable
TuneStart. (see TuneStart™ (P.52))
NOTE
• Compatible with SXV200 or later tuner models.
45English
Page 46
SiriusXM®
TuneScan™
TuneScan™ is a feature that plays samples
from the starts of multiple buffered songs
from each of the SmartFavorites channels that
predominantly play music selections.
You have easy access to a large sampling of
music content and can enjoy hearing a full
song when stopping the scan on a song of
interest.
Touch on the left side of the screen.
1
Touch [TuneScan] to begin scanning your
2
SmartFavorites channels.
You will hear a few seconds of the songs
from each of the SmartFavorite channels.
Touch [TuneScan] again while your
3
favorite song is being played to start
listening to that song.
Traffic & Weather Now™
Traffic & Weather Now™ allows you to access
the latest report whenever you want to hear
it. Select your city at the set up menu Select a City for Traffic & Weather (P.52).
Touch on the left side of the screen.
1
Touch [Traffic & Weather].
2
The report starts from the beginning. To stop
and return to the previous channel, touch it
again.
Indicator display
•
(White) : Played already.
•
(Green) : New information arrived.
•
(Purple) : Playing.
•
(Gray) : No information.
NOTE
• Compatible with SXV200 or later tuner models.
Scan finishes and continues playing the
song.
NOTE
• To cancel TuneScan™, Touch on the left side of the
screen. Touch [TuneScan].
• Touch and hold [TuneScan] to cancel TuneScan,
the channel before starting TuneScan will be
played.
• Compatible with SXV200 or later tuner models.
46
Page 47
SiriusXM®
Content Alerts
When a broadcast program related to the
registered artist, song or team starts, a
message appears to allow you to switch the
current channel to the relevant channel.
When the broadcast of the registered
1
content starts, an Alert screen appears.
■ [Jump]
Touch to display the Alert Content List
screen.
■ [Ignore]
Touch to cancel the Content Alerts.
Select a content from the list.
2
SportsFlash™
SportsFlash™ will notify you when a big play
happens during a game with one of your
favorite sports teams. Choose to tune in and
hear the play unfold like it was live. Continue
listening to the game, or you can return to
your previous channel.
When a big play happens during one of
1
the games, an Alert screen appears.
■ [Jump]
Touch to tune to that channel and play back
the big play.
■ [Ignore]
Touch to cancel this specific Sports Flash
Alert. Touching [Ignore] will ignore this
specific alert but will allow future alerts for
this game.
■ [Cancel]
Touch to cancel the SportsFlash alert. No
alerts from this game will be displayed
afterward.
NOTE
• Touch [Info Change]. Select the sequence of the
channel list as follows;
Artist Alert, Song Alert, GameAlert™
• To learn how to register artists and songs the
Team alert function, see 2. Information display of
SiriusXM® Basic Operation (P.41).
• To learn how to set up the Content Alerts
function, see Content Alerts setup (P.50).
NOTE
• Compatible with SXV300 or later tuner models.
• To learn how to set up the SportsFlash alert
function, see SportsFlash™ setup (P.51).
47English
Page 48
SiriusXM®
SiriusXM Setup
Touch on the left side of the screen.
1
Touch [SETUP].
Ñ Parental code
You can set a SiriusXM parental code for
Parental Control.
Touch [Parental Code] in the SiriusXM
1
SETUP screen.
Parental Pass Check screen appears.
NOTE
• The code number is set to “0000” as default.
Enter the current code number and touch
2
[Enter].
Parental Pass 1st entering screen
appears.
Enter the new code number and touch
3
[Enter].
SiriusXM SETUP screen appears.
See the following section for each
setting.
• Set up the parental code (P. 48)
• Set up the Parental Control (P. 49)
• Set up the skip channel select ( P.50)
• Set up the Content Alerts (P.50)
• Set up the team for SportsFlash™ (P. 51)
• Select the city for Traffic & Weather Jump
or Traffic & Weather Now™ (P.52)
• Set up the TuneStart™ (P. 52)
• Reset to the default settings (P.52)
48
Parental Pass 2nd entering screen
appears.
Enter the same code number as you input
4
in step 2 and touch [Enter].
The code number is confirmed and
SiriusXM parental code is now set.
Page 49
SiriusXM®
Ñ Parental Control
Parental Control is a feature that provides the
user with the ability to prevent unauthorized
access to mature content and user selected
channels.
Touch [Parental Control] in the SiriusXM
1
SETUP screen.
Touch [Mature], [User] or [OFF].
2
■ [OFF]
Deactivates the parental mature and user
locks.
■ [Mature]
Locks channels classified as “mature” only.
■ [User]
Locks only the selected channels.
Enter the parental code you originally
3
input in Parental code (P.48) and touch [Enter].
When selecting [User]
This allows you to limit access to any SiriusXM
channel (Parental Lock Channel).
Touch [Parental Lock Channel Selection]
1
in the SiriusXM SETUP screen.
Parental Pass Check screen appears.
NOTE
• Touch [All-Channels] to display all the
channels.
• To delete the parental lock channel setting,
touch [Disable All] and then touch [YES] on
the confirmation screen.
Touch each channel on the list and set to
4
ON or OFF.
On: If you wish to set the lock.
Off: If you wish to unlock the channel.
NOTE
• Touch [Info Change]. Select the sequence of the
channel list as follows;
• Channel name, Artist name, Song title, Category
name, Content information.
NOTE
• You need to set up a Parental code (P.48)
beforehand.
Enter the parental code you originally
2
input in Parental code (P.48) and touch [Enter].
Parental Lock Category Select screen
appears.
Touch the desired category from the list.
3
Displays all the channels in the selected
category.
49English
Page 50
SiriusXM®
Ñ Skip channel select
You can set the undesired channels to skip.
Touch [Skip Channel Select].
1
Skip Category Select screen appears.
Touch the desired category from the list.
2
Displays all the channels in the selected
category.
Touch each channel on the list and set to
3
ON or OFF.
Ñ Content Alerts setup
Activating content alert
Touch [Content Alerts] in the SiriusXM
1
SETUP screen.
The Content Alerts is turned on or off.
Default is “ON”.
Selecting the content for the content
alert
Touch [Content Alerts Content Set] in the
1
SiriusXM SETUP screen.
Artist list screen appears.
Select the content you want to set up.
2
NOTE
• You need to set up a Parental code (P.48)
beforehand.
Touch each content list and set ON or OFF.
3
NOTE
• To delete the skip channel setting, touch
[Disable All] and then touch [YES] on the
confirmation screen.
• Touch [Info Change]. Select the sequence of the
channel list as follows;
Channel name, Artist name, Song title, Category
name, Content information.
50
NOTE
• You can select “ON” up to 30 items of Artist, Song,
and Team.
● To delete the Artist and Song
Touch [Delete].
1
Page 51
Touch each content list.
2
Touch [Delete] and then touch [YES] on the
3
confirmation screen.
To select a Team
Get alerted when your favorite sports team
is playing on another SiriusXM channel with
GameAlert™
Touch [My Games].
1
Touch the desired league from the list.
2
SiriusXM®
Ñ SportsFlash™ setup
Activating SportsFlash
Touch [SportsFlash] in the SiriusXM
1
SETUP screen.
The SportsFlash is turned on or off.
Default is “ON”.
Selecting the team for SportsFlash
Touch [SportsFlash Team Set] in the
1
SiriusXM SETUP screen.
Team Set screen appears.
Touch [Edit].
2
Touch the desired league from the list.
3
Touch each team list and set ON or OFF.
3
NOTE
• You can select “ON” up to 30 items of Artist, Song,
and Team.
Touch each team list and set ON or OFF.
4
Touch [] twice.
5
51English
Page 52
SiriusXM®
■ [Edit]
Sets and removes teams.
■ [Priority]
Sets the priority of a team to be posted.
■ [Clear]
Removes all teams that have been set.
Touch [Clear]. When the confirmation screen
appears, touch [YES].
NOTE
• SportsFlash™ is available on SXV300 or later tuner
models.
• Up to 50 teams can be added.
Set the SportsFlash™ Team Priority
Touch [Priority].
1
Ñ Select a City for Traffic &
Weather
You can select a city for which you wish to
receive SiriusXM Traffic & Weather broadcasts
and hear them from the beginning.
Touch [Traffic & Weather City Select] in
1
the SiriusXM SETUP screen.
Touch [T] and [U] to select a city.
2
Ñ TuneStart™
Touch [Tune Start] in the SiriusXM SETUP
1
screen.
The TuneStart is turned on or off.
Default is “ON”.
Ñ Reset
Set the priority of a team.
2
Each time you touch Team, the priority is
set and reset.
Touch [Done].
3
NOTE
• Priority can be set on up to 5 teams.
52
Touch [SiriusXM Reset] in the SiriusXM
1
SETUP screen.
Confirmation screen appears.
Touch [YES].
2
All SiriusXM settings return to default.
Page 53
Bluetooth Control
Bluetooth Control
Using the Bluetooth function, various
functions can be used: listening to the audio
file, making/receiving a call.
Information for using
Bluetooth® devices
Bluetooth is a short-range wireless radio
communication technology for mobile devices
such as mobile phones, portable PCs, and
other devices.
Bluetooth devices can be connected without
cables and communicate with each other.
NOTE
• While driving, do not perform complicated
operations such as dialing numbers, using the
phone book, etc. When you perform these
operations, stop your car in a safe place.
• Some Bluetooth devices may not connect to this
unit depending on the Bluetooth version of the
device.
• This unit may not work for some Bluetooth
devices.
• Connecting conditions may vary depending on
your environment.
• For some Bluetooth devices, the device is
disconnected when the unit is turned off.
Ñ About the cell-phone and
Bluetooth audio player
This unit conforms to the following Bluetooth
specifications:
A2DP (Advanced Audio Distribution Profile)
AVRCP (V1.5) (Audio/Video Remote Control
Profile)
Sound codec
SBC, AAC
NOTE
• For the cell-phones verified for compatibility,
access the following URL:
http://www.kenwood.com/cs/ce/bt/.
• The units supporting the Bluetooth function have
been certified for conformity with the Bluetooth
Standard following the procedure prescribed by
Bluetooth SIG.
• However, it may be impossible for such units to
communicate with your cell-phone depending
on its type.
53English
Page 54
Bluetooth Control
Register from the Bluetooth
unit
It is necessary to register the Bluetooth audio
player or cell-phone to this unit before using
the Bluetooth function.
You can register up to 10 Bluetooth units.
NOTE
• Up to 10 Bluetooth units can be registered. If an
attempt is made to register the 11th Bluetooth
unit, the Bluetooth unit connected on the earliest
date will be deleted to register the 11th one.
• This unit is compatible with the Apple Easy
Pairing function. When an iPod touch or iPhone is
connected to this unit, an authentication dialog
appears. Performing operation for authentication
on this unit or iOS smartphone registers the
smartphone as a Bluetooth device.
Follow the step 1, 2 and 3 for registration.
Step 1: Registration from the Bluetooth
device
Search the unit (“DDX****”/ “DMX****”)
1
from your smartphone/cell-phone.
Input the PIN code in your smartphone/
2
cell-phone.
PIN code is set to “0000” as the default.
Step 2: Connection settings
• When the HFP profile is supported, Hands Free
1 or 2 is automatically selected for connection,
proceeding to the next step.
• When the A2DP or SPP profile is supported,
the cell-phone or audio player is automatically
connected, proceeding to the next step.
If cell-phones and/or audio players have already
been connected, a selection screen appears.
Select the hands-free number to connect.
1
A name of a smartphone is displayed when
it has hands-free connection with the unit.
Select if you want to use the audio player
2
app in your smartphone over A2DP, and
the other apps in your smartphone over
SPP.
This message appears if the device
supports BT audio (A2DP) or smartphone
link (SPP).
● SSP (Secure Simple Pairing of Bluetooth
2.1 or later)
Search the unit (“DDX****”/ “DMX****”)
1
from your smartphone/cell-phone.
Confirm the request both on the
2
smartphone/cell-phone and the unit.
54
Page 55
Bluetooth Control
Step 3: Phonebook transfer
Select if you want to transfer your
1
phonebook data.
This message appears if the device
supports PBAP.
The phonebook data transmission starts.
Some smartphones may request
permission to access the data. The
data transmission will start with your
permission.
When the data transmission and
connection have completed, the Bluetooth
connection icon appears on the screen.
Bluetooth Setup
Press the [MENU] button.
1
Popup menu appears.
Touch [SETUP].
2
SETUP Menu screen appears.
Touch [Bluetooth].
3
Bluetooth SETUP screen appears.
See the following section for each
setting.
• Connect the Bluetooth unit (P. 56)
• Change the PIN code (P. 57)
• Change the device name (P. 57)
55English
Page 56
Bluetooth Control
Ñ Connect the Bluetooth unit
Touch [Select Device] in the Bluetooth
1
SETUP screen.
Touch the device name you want to
2
connect.
Profile select screen appears.
NOTE
• If the icon is lighted, it means that the unit will
use that device.
Set each profile as follows.
3
NOTE
• If a device has been paired, the Bluetooth unit
cannot be connected from the paired device.
To delete the registered Bluetooth unit
Touch [Delete].
1
Touch the device name to check.
2
■ [þ All]
Select all Bluetooth unit.
■ [¨ All]
Erases all check marks.
Touch [Delete].
3
Confirmation message appears.
Touch [Yes ].
4
■ TEL (HFP) 1, TEL (HFP) 2
The device is connected with the unit as
hands-free phone 1 or 2.
■ Audio (A2DP)/App (SPP)
Set to interwork with an application installed
in a smartphone or to use as an audio player.
Touch [Close].
4
56
Page 57
Bluetooth Control
Ñ Change the PIN code
Touch [PIN Code] in the Bluetooth SETUP
1
screen.
PIN Code Set screen appears.
Input the PIN code.
2
Touch [SET].
3
Ñ Change the device name
Touch [Device Name] in the Bluetooth
1
SETUP screen.
Change Device Name screen appears.
Input the device name.
2
Touch [Enter].
3
Playing Bluetooth Audio
Device
Most function can be controlled from the
source control screen.
To enter Bluetooth source, touch [Bluetooth]
icon in the source selection screen. (P. 11)
Ñ Bluetooth basic operation
Control screen
1
5
4
3
1
Device name/ [] / []
• Connected device name.
• [
] : Repeats the current track/folder. Each
time you touch the key, repeat mode switches
in the following sequence; File repeat ( ),
Folder repeat ( ), All songs repeat ( ),
Repeat off ( )
• [
] : Randomly plays all tracks in current
folder. Each time you touch the key, random
mode switches in the following sequence;
Folder random ( ), All random ( ),
Random off ( )
2
Information display *
Displays the name of the track information.
3
[Function bar *
• [1]: Searches file. See File search (P.58).
• [E][F]: Searches the previous/next
content. Touch and hold to fast forward or fast
backward. (It will be cancelled automatically
after about 50 seconds.)
• [D]: Plays.
• [H]: Pauses.
• [
] : Displays the Graphic Equalizer screen.
(P. 74)
2
57English
Page 58
Bluetooth Control
4
Function panel
Touch on the left side of the screen to display
the function panel. Touch again to close the
panel.
• BT DEVICE CHANGE] : Selects the device to
connect via Bluetooth audio (A2DP) or APP
(SPP). See Connect the Bluetooth audio (P. 58).
5
Play mode indicator/ Playing time
D, H: Current play mode indicator
The meanings of each icon are as follows;
D (play), B (fast forward), A (fast backward),
H (pause), I (stop).
* These items appear only when the audio player
which supports AVRCP profile is connected.
NOTE
• If the operation keys do not appear, operate from
the player.
• Depending on your cell-phone or audio player,
audio may be heard and controlled but text
information may not appear.
• If the volume is too low, raise it on your cell-
phone or audio player.
Ñ Connect the Bluetooth audio
Selects the device to connect via Bluetooth
audio (A2DP) or APP (SPP).
Touch on the left side of the screen.
1
Touch [BT DEVICE CHANGE].
Touch the device name you want to
2
connect.
Touch [Close].
3
Ñ File search
58
Touch [1].
1
Touch the desired file or folder.
2
When you touch a folder its contents are
displayed.
Touch desired item from the content list.
3
Playback starts.
NOTE
• For operations in the list screen, see List screen
(P. 14).
Page 59
Bluetooth Control
Using Hands-Free Unit
You can use telephone function by connecting
the Bluetooth telephone to this unit.
NOTE
• While Apple CarPlay or Android Auto is being
connected, Bluetooth Hands-Free function and
two Bluetooth devices connections cannot be
used. Only Apple CarPlay or Android Auto HandsFree function can be used.
Ñ Make a call
Touch [Û].
1
Hands Free screen appears.
NOTE
• If your mobile phone supports PBAP, you can
display the phone book and call lists on the
touch panel screen when the mobile phone is
connected.
– Phone book: up to 1000 entries
– Up to 50 entries including dialed calls, received
calls, and missed calls
Select a dialing method.
2
● Select the cell-phone to use
When you connect two cell-phones
1) Touch [
you want to use.
● Bluetooth SETUP
1) Touch [
Bluetooth SETUP screen appears.
NOTE
• The status icons such as battery and antenna
displayed may differ from those displayed on the
cell-phone.
• Setting the cell-phone in the private mode can
disable the hands-free function.
].
] to select the phone
Call using call records
Touch [].
1
Select the phone number from the list.
2
Call by entering a phone number
Touch [].
1
Enter a phone number with number keys.
2
• []: Call using call records
• [
]: Call using the phonebook
• [
]: Call using the preset number
• [
]: Call by entering a phone number
• [
]: Voice Recognition ( P.60)
Touch [].
3
59English
Page 60
Bluetooth Control
Call using the preset number
Touch [].
1
Touch the Name or phone number.
2
Call using the phonebook
Select the phone number from the list.
5
NOTE
• You can set the list to arrange in the order of last
name or first name. For details, see Hands-Free Setup (P.63).
Touch [].
1
Touch [].
2
Select the initial.
3
• Characters with no corresponding name
will not appear.
• During search, a non-accent character
such as “u” is searched for instead of an
accent character such as “ü”.
Select the person you want to call from
4
the list.
Ñ Voice Recognition
You can access the voice recognition function
of the cell-phone connected to this unit.
You can search the cell-phone phonebook
by voice. (The functionality depends on the
cell-phone.)
Press the [] button for 1 second.
1
Press for 1 second
Voice Recognition screen appears.
Start speaking.
2
NOTE
• You can use voice recognition function by
touching [] on the Hands Free screen.
60
Page 61
Bluetooth Control
Ñ Receive a call
Touch [ ] to answer a phone call or
1
[
] to reject an incoming call.
NOTE
• While monitoring the view camera, this screen
does not appear even if a call comes in. To display
this screen, press the [TEL] button or return the
shift knob of car to the driver position.
To end call
While talking, touch [].
1
Ñ Operations during a call
● Adjust the receiver volume
Press the [S] or [R] button.
● Mute your voice
Touch [
Touch [DTMF] to display the tone input screen.
You can send tones by touching desired keys
on the screen.
Touching [
the speaking voice output between cell-phone
and speaker.
When you receive a call while talking on
another call, you can answer the newly
received call by touching [
is on hold.
Each time you touch [
When you touch [
and switch to the call in hold.
The Hands-Free popup screen is closed. To
display it again, touch [
] to mute or not to mute your voice.
● Output the dial tone
● Switching the speaking voice output
]/ [] each time switches
● Call-waiting
]. The current call
], the caller will change.
], the current call will end
● [×]
].
● Adjust the volume of your voice
1) Touch [Speech Quality].
2) Touch [T] or [U] of [Microphone Level].
61English
Page 62
Bluetooth Control
Ñ Phone number preset
You can register frequently used phone
numbers to this unit.
Touch [].
1
Touch [Edit].
2
Select where to preset.
3
Select how to preset.
4
• [Add number from phonebook]:
Select the number to preset by referring to
“Call using the phonebook”. See Call using the phonebook (P.60).
• [Add number direct]:
Enter the telephone number directly and
touch [SET]. See Call by entering a phone number (P.59).
Ñ Phonebook transfer
You can transfer the phonebook in your
Bluetooth smartphone via PBAP.
Touch [].
1
Touch [].
2
The phonebook data transmission starts.
Phonebook deletion
Touch [].
1
Touch the name to check.
2
■ [þ All]
Checks all boxes.
■ [¨ All]
Erases all check marks.
Touch [Delete].
3
Confirmation message appears.
Touch [Yes ].
4
NOTE
• To delete the preset number, touch [Delete] and
then touch [Ye s] on the confirmation screen.
62
Page 63
Bluetooth Control
Hands-Free Setup
You can perform various setup about
handsfree function.
Press the [MENU] button.
1
Popup menu appears.
Touch [SETUP].
2
SETUP Menu screen appears.
Touch [Bluetooth].
3
Bluetooth SETUP screen appears.
Touch [TEL SETUP].
4
TEL SETUP screen appears.
Set each item as follows.
5
■ Auto Response*
Sets an automatic response time to pick-up
an incoming call.
OFF (Default): Automatic response is not
available.
1/ 5/ 10/ 15/ 20/ 25/ 30: Set calling ring
time (second).
■ Auto Pairing
When set to “ON”, the Apple Auto Pairing
function is turned on to automatically
register the iPod touch or iPhone connected
to this unit.
ON (Default): Uses Apple Auto Pairing
function.
OFF: Not uses Apple Auto Pairing function.
■ Sort Order
Sets how to arrange the cell-phone
phonebook.
First: Arranges in the order of first name.
Last (Default): Arranges in the order of last
name.
■ Echo Cancel Level
Adjusts the level of echo cancellation.
Default is “0”.
■ Noise Reduction Level
Reduces the noises generated by
surrounding environment without changing
the microphone volume. Use this setting
when the voice of caller is not clear. Default
is “0”.
■ Bluetooth HF/Audio
Select the speakers to output the sound from
cell-phone (such as phone call voice and
ringing tone) and Bluetooth audio player.
Front: Outputs from the front speakers.
All (Default): Outputs from all speakers.
* Either the time interval for automatic
answer set on this unit or the time
interval set on the cell-phone, whichever
is shorter takes effect.
Touch [OK].
6
63English
Page 64
Other External Components
Other External Components
View Camera
NOTE
• To connect a camera, see P.89.
• To use a rear view camera, a REVERSE lead
connection is required. (P. 88)
• The view of the front view camera or dashboard
camera varies depending on the setting of
[Dashboard Camera /Front Camera].
• If [R-CAM Interruption] is set to on, the camera
screen is displayed when you shift the gear to the
reverse (R) position.
Ñ Display the camera screen
Press the [MENU] button.
1
DDX9904S/ DDX9704S
DMX7704S
View camera screen appears.
Adjust each item as follows.
2
1
3
2
1
Switching the View Camera
Touch to change the front view camera or
dashboard camera and rear view camera.
2
Camera off
Touch to exit the camera screen.
3
Switching the Guideline
Touching each time turns on or off the
guideline. Available when [Rear Camera] is
set to [CMOS 3-Series Camera].
4
1
2
3
4
4
Switching the Angle
Touch to change the camera angles:
Available when [Dashboard Camera /
Front Camera] is set to [CMOS 3-Series
Camera].
Ñ Camera Setup
Press the [MENU] button.
Popup menu appears.
Touch [SETUP].
SETUP Menu screen appears.
Touch [Camera].
Camera screen appears.
Set each item as follows.
■ Rear Camera
CMOS 3-Series Camera: Select this when
the CMOS-3xx series with ID 1 set is
connected.
Other (Default): Select this when the other
camera is connected.
■ R-CAM Interruption
ON: Displays the picture from the rear view
camera when you shift the gear to the
reverse (R) position.
OFF (Default): Select this when no camera is
connected.
■ R-CAM Settings
If you select [CMOS 3-Series Camera] for
[Rear Camera], adjusts the CMOS-3xx series
with ID 1 set. For details, see the instruction
manual of your camera.
■ Parking Guidelines
You can display parking guidelines to enable
easier parking when you shift the gear to the
reverse (R) position.
Default is “ON”.
64
Page 65
■ Guidelines SETUP
If you select [ON] for [Parking Guidelines],
adjust the parking guidelines. See To adjust the parking guidelines (P.65).
■ Dashboard Camera /Front Camera
Dashboard Camera: Select this when the
dashboard camera is connected.
CMOS 3-Series Camera: Select this when
the CMOS-3xx series with ID 2 set is
connected.
Other: Select this when the other camera is
connected.
OFF (Default): Select this when no camera is
connected.
■ F-CAM Settings
If you select [CMOS 3-Series Camera] for
[Dashboard Camera /Front Camera],
adjusts the CMOS-3xx series with ID 2 set. For
details, see the instruction manual of your
camera.
■ Front Camera Mirror Image
If you select [ON] for [Dashboard Camera /
Front Camera].
ON: Displays the picture from the front view
camera horizontally reversed.
OFF (Default): Displays the picture from the
front view camera as it is.
To adjust the parking guidelines
NOTE
• Install the rear view camera in the appropriate
position according to the instructions supplied
with the rear view camera.
• When adjusting the parking guidelines, make
sure to use the parking brake to prevent the car
from moving.
Touch [ON] of [Parking Guidelines] in the
1
Camera screen. (P. 64)
Touch [Guidelines SETUP] in the Camera
2
screen.
Adjust the parking guidelines by
3
selecting the
mark.
Other External Components
Adjusting the position of the selected
4
mark.
A
C
B
Make sure that A and B are horizontally
parallel, and that C and D are the same
length.
NOTE
• Touch [Initialize] and after touch [Yes ] to set all
marks to the initial default position.
the
D
Use Dashboard Camera
A Dashboard Camera, DRV-N520 (optional
accessory), connected to this unit lets you play
video-recorded data and so on.
For details, see the instruction manual of
the Dashboard Camera DRV-N520 (optional
accessory).
NOTE
• To connect a camera, see P.90.
• Sets the dashboard camera/front camera as
[Dashboard Camera]. (P. 65)
Ñ Display the dashboard camera
screen
Press the [MENU] button.
1
Popup menu appears.
Touch [Camera].
2
65English
Page 66
Other External Components
1
Switching the View Camera
Touch to change the dashboard view camera
and rear view camera.
2
Camera off
Touch to exit the camera screen.
3
Key display
Touch to display the dashboard camera
control buttons.
External audio/video players—
AV-IN
Ñ Start playback
Connect an external component to the
1
AV-IN input terminal. (P.89)
Select [AV-IN] as the source. (P. 11)
2
Turn on the connected component and
3
start playing the source.
OEM Features Operation
By connecting this unit to the bus system of
the vehicle using an iDataLink (commercially
available), this unit can access the satellite
radio source provided for the vehicle and
vehicle information can be displayed on this
unit.
Press the [HOME] button.
1
HOME screen appears.
Touch [] on the HOME screen.
2
Touch icon.
3
123
• Displays the control screen of the satellite
radio source provided for the vehicle.
• Displays the control screen of the media
player source provided for the vehicle.
• Displays the control screen of the
Bluetooth Hands Free function provided
for the vehicle.
• Displays the control screen of the
Bluetooth streaming source provided for
the vehicle.
• Displays information about the
instruments such as a speedometer.
• Displays information about the air
conditioner of the vehicle. *
• Displays information about the Parking
Distance Sensor of the vehicle.
• Displays information about the tire
pressures of the vehicle. *
• Displays information about the Radar
Detector. *
* These ADS adapter features are displayed as the
widget on the Home screen. (P. 10) You can display
these screens by touching the widget.
NOTE
• Displayable screens, button names, and screen
names vary depending on the type of the
connected iDataLink and the model of the
vehicle. For more details, access the following
URL:
www.idatalink.com/
66
Page 67
Setting Up
Setting Up
Monitor Screen Setup
You can adjust image quality in video, menu
screen, etc.
Press the [MENU] button.
1
Popup menu appears.
Touch [Screen Adjustment].
2
Screen Control screen appears.
Adjust each item as follows.
3
■ Backlight / Contrast / Black / Brightness
/ Color / Tint
Adjusts each item.
■ Aspect
Select screen mode.
Full: Changes the aspect ratio of video and
displays fully on the screen.
Normal: Displays with 4:3 ratio.
Auto:
DVD, VCD and disc media: Video of 16:9
ratio is displayed in Full and video of 4:3
ratio is displayed in Regular.
USB device: Displays video fully on vertical
or horizontal with no ratio change.
System Setup
NOTE
• Each operation in this section can be started from
the multi function menu.
Press the [MENU] button.
1
Popup menu appears.
Touch [SETUP].
2
See the following section for each
setting.
• Set up AV (P. 71)
• Set up display (P.69)
• Set up the user interface ( P.68)
• Set up camera (P.64)
• Set up special (P.69)
• Set up Bluetooth (P.55)
NOTE
• Adjusting items are different depending on the
current source.
67English
Page 68
Setting Up
User Interface Setup
You can setup user interface parameters.
Press the [MENU] button.
1
Popup menu appears.
Touch [SETUP].
2
SETUP screen appears.
Touch [User Interface].
3
User Interface screen appears.
Set each item as follows.
4
■ Beep
Turns the key touch tone on or off.
Default is “ON”.
■ Parking Assist Display
When an ADS adapter is connected, you can
display information about obstacles around
the car.
ON: Always displays information.
Dyn. (Default): Displays information when
the sensor detects obstacles.
OFF: Cancels.
This can be set when the iDataLink
(commercially available) is connected.
■ Parking Assist Position
Select where information about obstacles is
displayed on the screen (left or right).
“Left”/ “Right” (Default)
This can be set when the iDataLink
(commercially available) is connected.
■ Language Select
Selects a language.
■ Touch Panel Adjust (
Adjust the sensing position of touch panel.
(P. 68)
■ Clock
GPS-SYNC (Default): Synchronizes the clock
time with the GPS.
Manual: Sets the clock manually
■ Time Zone
Select the time zone.
)
■ Clock Adjust
If you select [Manual] for Clock, adjust the
date and time manually. (P. 68)
Ñ Adjust the date and time
manually.
Touch [Time Zone] in the User Interface
1
screen.
Select the time zone.
2
Touch [Clock Adjust] in the User Interface
3
screen.
Adjust the date, then adjust the time.
4
Touch [Set].
5
Ñ Touch panel adjustment ()
Touch [Touch Panel Adjust] on the User
1
Interface screen.
Touch Panel Adjust screen appears.
Follow the instruction on the screen and
2
long touch the center of each [ ].
2
1
NOTE
• To cancel the touch panel adjustment, touch
[Cancel].
• To reset to the initial status, touch [Reset].
68
Page 69
Setting Up
Special Setup
You can setup Special parameters.
Press the [MENU] button.
1
Popup menu appears.
Touch [SETUP].
2
SETUP screen appears.
Touch [Special].
3
Special screen appears.
Set each item as follows.
4
■ DEMO
Set the demonstration mode. Default is “ON”.
■ Manual Power OFF
Assigns the function of the [HOME] button
when held.
AV OFF: Turns off the screen and audio.
Interrupts from incoming hands-free
calls, rear camera views and so on are
functional, though.
Complete OFF (Default): Switches off the
power. Interrupts are not functional.
■ SETUP Memory
Locks or unlocks the Audio SETUP Memory/
Recall/Clear.
Clears the AUDIO SETUP Memory and the
currently memorized audio setting.
■ Software Information
Check the software version of this unit.
(P. 69)
■ Open Source Licenses
Displays the open source licenses.
■ Initialize
Touch [Initialize] and then touch [Yes ] to set
all the settings to the initial default settings.
• Audio SETUP Memory is not initialized.
Ñ Software Information
Check the software version of this unit.
Touch [Software Information] in the
1
Special screen.
Confirm the software version.
2
NOTE
• For how to update the software, see the relevant
update procedure manual which comes with the
software.
Display Setup
Press the [MENU] button.
1
Popup menu appears.
Touch [SETUP].
2
SETUP screen appears.
Touch [Display].
3
Display screen appears.
Set each item as follows.
4
■ Dimmer
Select dimmer mode.
OFF: The display and buttons do not dim.
ON: The display and buttons dim.
SYNC (Default): Turns the dimmer function
on or off when the vehicle light control
switch is turned on or off.
69English
Page 70
Setting Up
■ OSD Clock
Select if you want to display the clock while
watching DVD video, etc.
"ON" (Default)/ "OFF"
■ Key Color
You can set the button illumination color.
(P. 70)
■ Background
Changing background image or color.
(P. 70)
■ Viewing Angle
If it is hard to see the image on the screen
even after adjusting the front panel angle,
adjust the viewing angle. The smaller the
(negative) value, the more whitish the image
on the screen looks.
"0" (Default)/ "-1"/ "-2"/ "-3"
Ñ Customizing the key color
You can set the button illumination color.
Touch [Key Color] in the Display screen.
1
Touch the desired color.
2
Use [−] and [+] to adjust each color value.
3
Touch [ .
4
Ñ Change background image or
color
Touch [Background] in the Display screen.
1
Select an image.
2
1
*
*1 Select a background color in advance.
2
*
Select an original image in advance.
2
*
■ User
The color you have set in the process of
[Adjust] is registered.
■ Scan
You can set the key color to continuously
scan through the color spectrum.
Touch [ ].
3
To register original color
You can register your original color.
Touch [User] in the Key Color screen.
1
Touch [Adjust].
2
70
To select background color
Touch [Background Color] in the
1
Background screen.
Select a background color.
2
1
*
*1 The color you have selected at [Key Color]
is added on the image. If you select “Scan” at
[Key Color], you cannot select this image.
Touch [ .
3
Page 71
Setting Up
To register original image
You can load an image from the connected
USB device and set it for the background
image.
Before operating this procedure, it is necessary
to connect the device which has the image to
load.
You can select an AV source to be output
from the AV OUTPUT port.
OFF, AV-IN, DISC, USB, or iPod
You cannot select iPod if it is connected via
Bluetooth.
If you select USB, iPod, Disc, Spotify, Pandora,
Bluetooth audio, Apple CarPlay or Android
Auto as the main source, you cannot select
USB or iPod as the AV output source.
■ CarPlay Sidebar
Select the position of the control bar (left or
right) shown on the touch panel.
“Left” (Default)/ “Right”
■ OEM SETUP
Confirm the information about/ change the
settings for using the ADS adapter.
71English
Page 72
Controlling Audio
Controlling Audio
NOTICE
• Each operation in this section can be started from
the multi function menu.
You can adjust the various settings such as
audio balance or subwoofer level.
Press the [MENU] button.
1
Popup menu appears.
Touch [Audio].
2
See the following section for each
setting.
• Set up speaker/ X’over (P.72)
• Controlling equalizer (P. 74)
• Set listening position/ DTA (P.77)
• Controlling general audio (Fader /
Balance) (P. 73)
• Set volume offset (P. 75)
• Performing zone control (P. 75)
• Set sound effect (P.76)
Speaker/ X’over setup
Press the [MENU] button.
1
Popup menu appears.
Touch [Audio].
2
Audio screen appears.
Touch [Speaker/Xʼover].
3
Select a car type.
4
You can setup the car type and speaker
network, etc.
If your car type is selected, the Delay Time
Alignment is set automatically (for timing
adjustment of sound output for each
channel) to have the highest surround
effects.
Touch the speaker (1) you wish to adjust
5
and set each item (2) as follows.
1
2
72
■ Speaker
You can select a speaker type and its size to
get the best sound effects.
When the speaker type and size are set,
the speaker crossover network is set
automatically.
■ Location (Only for Front, Rear)
Select the speaker position you have fixed.
Page 73
Controlling Audio
■ Tweeter (Only for Front)
You can set the tweeter when you are
selecting front speakers.
None, Small, Medium, Large
■ X’over
Displays the speaker crossover setup screen.
You can adjust the crossover setup that was
set automatically when you selected the
speaker type.
For details, see Crossover network setup
(P. 73)
Ñ Crossover network setup
You can set a crossover frequency of speakers.
Touch [Xʼover].
1
Touch the speaker to set.
2
Set each item as follows.
3
■ TW (Tweeter) Gain *
Adjusts the tweeter level. (When front is
selected on Speaker Select screen)
■ Phase Inversion*
Sets the phase of subwoofer output.
Check [Phase Inversion] to shift the phase
180 degrees. (When subwoofer is selected
on Speaker Select screen)
1
*
Only when “LPF FREQ”/“HPF FREQ” is set to
a mode other than “Through” in [Xʼover].
2
*
Only when “Tweeter” is set to “Small”,
“Medium”, “Large” in [Speaker Setup].
3
*
Only when “Subwoofer” is set to a mode
other than “None” in [Speaker Setup].
2
3
Controlling General Audio
Press the [MENU] button.
1
Popup menu appears.
Touch [Audio].
2
Audio screen appears.
Touch [Fader / Balance].
3
■ HPF FREQ
High Pass Filter adjustment. (When front or
rear speaker is selected on Speaker Select
screen)
■ LPF FREQ
Low Pass Filter adjustment. (When subwoofer
is selected on Speaker Select screen)
1
■ Slope*
Sets a crossover slope.
■ Gain
Adjusts the front speaker, rear speaker, or
subwoofer level.
Set each item as follows.
4
■ Fader / Balance
Adjust the volume balance around the
touched area.
[C] and [D] adjust the right and left volume
balance.
[R] and [S] adjust the front and rear volume
balance.
■ [Center]
Clear the adjustment.
73English
Page 74
Controlling Audio
Equalizer Control
You can adjust equalizer by selecting the
optimized setting for each category.
Press the [MENU] button.
1
Popup menu appears.
Touch [Audio].
2
Audio screen appears.
Touch [Equalizer].
3
Touch the screen and set the Graphic
4
Equalizer as desired.
■ Gain level (dotted frame area)
Adjust the gain level by touching the each
frequency bar.
You can select frequency bar and adjust its
level by [R], [S].
■ Preset Select
Displays the screen to recall the preset
equalizer curve.
■ Memory
Saves the adjusted equalizer curve from
“User1” to “User4”.
■ Initialize
The current EQ curve returns to flat.
■ ALL SRC
Apply the adjusted equalizer to all sources.
Touch [ALL SRC] and then touch [OK] on the
confirmation screen.
■ Bass EXT (Bass Extend Settings)
When turned on, the frequency lower than
62.5 Hz is set to the same gain level as 62.5
Hz.
■ SW Level
Adjusts the subwoofer volume. This setting
is not available when subwoofer is set to
“None”. See Speaker/ X’over setup (P.72).
Ñ Recall the EQ curve
Touch [Preset Select].
1
Select EQ curve.
2
NOTE
• [iPod] is available only during iPod source.
Ñ Save the EQ curve
Adjust the EQ curve.
1
Touch [Memory].
2
Select where to save.
3
74
Page 75
Controlling Audio
Volume Offset
Finely adjust the volume of the current source
to minimize the difference in volume between
different sources.
Press the [MENU] button.
1
Popup menu appears.
Touch [Audio].
2
Audio screen appears.
Touch [Volume Offset].
3
Touch [+] or [−] to adjust the level.
4
■ Initialize
Returns to the initial settings.
* If you have increased the volume first, then
reduced the volume using the “Volume
Offset”, the sound generated if you suddenly
switch to another source may be extremely
loud.
Zone Control
You can select different sources for both front
and rear positions in the vehicle.
Press the [MENU] button.
1
Popup menu appears.
Touch [Audio].
2
Audio screen appears.
Touch [Zone Control].
3
Zone Control screen appears.
Touch [Zone Select].
4
Touch [Dual Zone].
5
Set each source as follows.
6
■ [Zone Select]
Touch [Single Zone] to turn off the dual
zone function.
■ [Front Source] [Rear Source]
Select the audio source for each.
■ [Rear VOL.]
Adjusts the rear source volume.
75English
Page 76
Controlling Audio
NOTE
• When the rear speaker sound is switched, the
audio source that is output at the AV OUTPUT
terminal is also switched to the same source.
• When the dual zone function is set to on, the
following functions are not available.
– Output from the subwoofer
– Subwoofer Level/ Bass Boost ( P.76)
– Equalizer Control/ Sound Effect/ Listening
• You cannot select iPod if it is connected via
Bluetooth.
• If you select USB, iPod, Disc, Bluetooth audio,
Apple CarPlay or Android Auto as the Front
Source, you cannot select USB or iPod as the Rear
Source.
Sound Effect
You can set sound effects.
Press the [MENU] button.
1
Popup menu appears.
Touch [Audio].
2
Audio screen appears.
Touch [Sound Effect].
3
Set each item as follows.
4
■ Bass Boost
Sets the amount of bass boost among “OFF”/
“1”/ “2”/ “3”.
■ Loudness
Sets the amounts of boost of low and high
tones.
“OFF”, “Low”, “High”
■ Drive Equalizer
Reduces the driving noise by raising the
bandwidth.
“OFF”, “ON”
■ Space Enhancer
Select the feeling of sound space
enhancement.
“OFF”/ “Small”/ “Medium”/ “Large”.
This setting is not available during HD Radio
tuner source.
■ Supreme
Turns ON/OFF the Supreme function.
Technology to extrapolate and supplement
with proprietary algorithm, the highfrequency range that is cut off when
encoding.
76
Page 77
■ Realizer
Virtually makes the sound more realistic
using the Digital Signal Processor (DSP)
system.
Select the level from “OFF”/ “1”/ “2”/ “3”.
■ Stage EQ
You can adjust the height of speakers
virtually to suit your listening position.
“OFF”/ “Low”/ “Middle”/ “High”.
Listening Position/ DTA
Listening Position/DTA allows you to improve
the sound field depending on the position of
the seat you sit.
Listening Position/DTA allows you to set
“Listening Position” and “Front Focus”. You
cannot set both at the same time.
Press the [MENU] button.
1
Popup menu appears.
Touch [Audio].
2
Audio screen appears.
Touch [Position/DTA].
3
Controlling Audio
Position DTA control
You can fine-adjust your listening position.
Touch [Adjust].
1
Touch [Delay].
2
Touch [T] or [U] to adjust the delay time of
3
the selected speaker.
• Set up Listening Position (P. 77)
• Set up Front Focus (P. 78)
Ñ Listening Position
Adjust the sound delay time as nearer speakers
to the selected seat have more delay time,
so that the sound from each speaker arrive a
listener at the same time.
• To return to the initial setting of Delay and Level,
touch [Initialize] and [YES] in the confirmation
screen.
77English
Page 78
Controlling Audio
Ñ Front Focus
This is the function to focus the imaginary
sound image in front of the selected seat.
Touch [Front Focus] in the Position/DTA
1
screen.
Select a front focus position.
2
For [Front All] and [All], select Priority L or R
depending on which side you want to put
the imaginary sound image.
Ñ Front Focus fine adjustment
Touch [Adjust].
1
Touch [Delay].
2
Set each item as follows.
3
■ Sound Image LR (Front)
Adjust the sound image to focus on in front
of front seats.
■ Sound Image LR (Rear)
Adjust the sound image to focus on in front
of rear seats.
■ Size of the Virtual Sound Field
Adjust the size of sound image to meet your
taste. If the sound image is shifted from the
front, adjust it by [Sound Image LR (Front)]
or [Sound Image LR (Rear)].
■ Subwoofer Delay
Adjust the delay time of subwoofer.
Touch [Level].
4
Touch [T] or [U] to adjust the sound level
5
of the selected speaker.
78
NOTE
• To return to the initial setting of Delay and Level,
touch [Initialize] and [YES] in the confirmation
screen.
Page 79
Remote control
Remote control
This unit can be operated using the remote
control KNA-RCDV331 (optional accessory).
# CAUTION
• Put the remote control in a place where it will
not move during braking or other operations.
A dangerous situation could result, if the
remote control falls down and gets wedged
under the pedals while driving.
• Do not leave the battery near fire or under
direct sunlight. A fire, explosion or excessive
heat generation may result.
• Do not recharge, short, break up or heat the
battery or place it in an open fire. Such actions
may cause the battery to leak fluid. If spilled
fluid comes in contact with your eyes or on
clothing, immediately rinse with water and
consult a physician.
• Place the battery out of reach of children. In
the unlikely event that a child swallows the
battery, immediately consult a physician.
Battery Installation
If the remote control operates only over
shorter distances or does not operate at all, it
is possible that the batteries are depleted.
In such instances, replace the both batteries
with new ones.
Insert two “AAA”/“R03”-size batteries
1
with the and poles aligned properly,
following the illustration inside the case.
79English
Page 80
Remote control
Functions of the Remote
control Buttons
Ñ Switch the operation mode
The functions operated from the remote
control differ depending on the position of the
mode switch.
AUD
•
DVD
•
•
T V
•
NAV
■ AUD mode
Switch to this mode when controlling a
selected source or tuner source, etc.
■ DVD mode
Switch to this mode when playing a disc
media including DVD, VCD, and CD.
■ NAV mode
Not used.
■ TV mode
Not used.
NOTE
• When controlling a player that is not integrated in
the unit, select “AUD” mode.
Ñ Direct search mode
Using the remote control, you can jump
directly to the desired file, track chapter, etc.
with entering the number corresponding to
the content.
NOTE
• This operation cannot be performed for USB
device and iPod.
Press the [#BS] button several times until
1
the desired content appears.
The available contents are different
depending on the source.
■ DVD
Title number/Chapter number
■ VCD 1.X and 2.X (PBC OFF)
Track number
■ VCD 2.X (PBC ON)
Scene number/Track number
■ Music CD
Track number
■ HD Radio tuner
Frequency value/Channel number
■ SiriusXM
Channel number
Enter the number of the content you want
2
to play using the numeric keypad.
For DVD or VCD, music CD, press the
3
[ENTER] button.
For radio, press the [C] or [D] button.
The content you entered is played.
80
Page 81
Remote control
4
1
3
2
5
6
7
17
19
21
22
23
18
20
11
8
9
10
12
13
24
14
25
15
26
16
Key
Name
SRCAUDSwitches to the source to be played.
1
NAV−Switches between the navigation and the source screens.
2
MENUDVDStops playing and memorizes the last point where the disc stopped. The last point
3
OUT, IN−Not used.
4
POSITIONAUD, DVDPauses the track or file, and resumes playing by pressing twice.
5
Cursor Key DVDMoves the cursor in the DVD menu.
6
ENTERAUD, DVDPerforms the selected function.
7
ROUTE MAUDScreen mode changes each time you press this key during video playback.
8
VOICEAUDDisplays the control screen of current source. (USB, iPod, DISC)
9
VIEWAUD, DVDSwitches the AV source to be output.
10
MAP DIRAUD, DVDSwitches the display angle each time it is pressed.
11
Mode
switch
In hands-free mode, hangs up the phone.
is deleted by pressing twice.
During radio, HD Radio, and SiriusXM source in AUD mode, switches the seek
mode.
DVDReturns to the DVD top menu.
DVDDisplays the DVD menu.
Turns the playback control on or off while playing VCD.
Function
81English
Page 82
Remote control
Key
Name
R/S
12
C/D
13
Numeric
14
Keypad
* +DVDClears the number.
15
# BSAUD, DVDSwitches to the direct search mode.
16
AUDIODVDSwitches the voice language each time you press this key.
17
CANCELDVDDisplays previous screen.
18
SUBTITLEDVDSwitches the subtitle language.
19
20
ANGLEDVDSwitches the picture angle each time you press this key.
21
Vol RS
22
ZOOMDVDSwitches the zoom ratio (2, 3, 4, Off ) each time you press this key.
23
2 ZONEAUD, DVDSwitches the Dual Zone function on and off.
24
R.VOL −Adjusts volume at rear when the Dual Zone function is on.
25
AT T−Lowers the volume by pressing the key once.
26
Mode
Function
switch
AUD, DVDSelects the folder to be played.
AUD, DVDSelects the track or file to be played.
AUDSpecifies the number to search in direct search.
DVD
−When a call comes in, answers the call.
−Adjusts the volume.
During radio and HD Radio source in AUD mode, select FM/ AM band to be
received.
During SiriusXM source in AUD mode, switches the bands to be received.
During radio, HD Radio, and SiriusXM source in AUD mode, switches to broadcast
stations received by the unit.
For details on the direct search mode, see Direct search mode (P.80).
• Press [1][2] to fast forward/backward.
• Press [4][5] to slow forward/backward. Switches the slow playback speed each
time you press this key.*
*DVD only
For details on the direct search mode, see Direct search mode (P.80).
Restores the previous volume by pressing the key twice.
82
Page 83
Connection/Installation
Connection/Installation
Before Installation
Before installation of this unit, please note the
following precautions.
# WARNINGS
• If you connect the ignition wire (red) and
the battery wire (yellow) to the car chassis
(ground), you may cause a short circuit, that
in turn may start a fire. Always connect those
wires to the power source running through
the fuse box.
• Do not cut out the fuse from the ignition wire
(red) and the battery wire (yellow). The power
supply must be connected to the wires via
the fuse.
# CAUTION
• Install this unit in the console of your vehicle.
Do not touch the metal part of this unit during
and shortly after the use of the unit. Metal part
such as the heat sink and enclosure become
hot.
NOTE
• Mounting and wiring this product requires
skills and experience. For best safety, leave the
mounting and wiring work to professionals.
• Make sure to ground the unit to a negative 12V
DC power supply.
• Do not install the unit in a spot exposed to
direct sunlight or excessive heat or humidity.
Also avoid places with too much dust or the
possibility of water splashing.
• Do not use your own screws. Use only the
screws provided. If you use the wrong screws,
you could damage the unit.
• If the power is not turned ON (“ There is an
error in the speaker wiring. Please check the
connections.” is displayed), the speaker wire
may have a short-circuit or touched the chassis
of the vehicle and the protection function may
have been activated. Therefore, the speaker
wire should be checked.
• If your car’s ignition does not have an ACC
position, connect the ignition wires to a power
source that can be turned on and off with the
ignition key. If you connect the ignition wire to
a power source with a constant voltage supply,
such as with battery wires, the battery may be
drained.
• If the console has a lid, make sure to install the
unit so that the front panel will not hit the lid
when closing and opening.
• If the fuse blows, first make sure the wires
aren’t touching to cause a short circuit, then
replace the old fuse with one with the same
rating.
• Insulate unconnected wires with vinyl tape or
other similar material. To prevent a short circuit,
do not remove the caps on the ends of the
unconnected wires or the terminals.
• Connect the speaker wires correctly to the
terminals to which they correspond. The unit
may be damaged or fail to work if you share
the ¤ wires or ground them to any metal part
in the car.
• When only two speakers are being connected
to the system, connect the connectors either
to both the front output terminals or to both
the rear output terminals (do not mix front
and rear). For example, if you connect the ¢
connector of the left speaker to a front output
terminal, do not connect the ¤ connector to
a rear output terminal.
• After the unit is installed, check whether the
brake lamps, blinkers, wipers, etc. on the car
are working properly.
• Mount the unit so that the mounting angle is
30° or less.
• This unit has the cooling fan to decrease the
internal temperature. Do not mount the unit
in a place where the cooling fan of the unit is
blocked. Blocking these openings will inhibit
the cooling of the internal temperature and
result in malfunction.
Cooling fan
83English
Page 84
Connection/Installation
• Do not press hard on the panel surface when
installing the unit to the vehicle. Otherwise
scars, damage, or failure may result.
• Reception may drop if there are metal objects
near the Bluetooth antenna.
Bluetooth antenna unit
Ñ Supplied accessories for
installation
1
x1
2
(Black 1 m)
3
(Gray 1 m)
4
(3 m)
x1
x1
9
0
[1]
DDX9904S only
(3.5 m)
x1
x1
84
[1]
5
6
(M5 x 8 mm)
7
(M5 x 8 mm)
[1]
8
x1
x2
x6
x6
x1
Page 85
Connection/Installation
Ñ Installation procedure
1) To prevent a short circuit, remove the key
from the ignition and disconnect the ¤
terminal of the battery.
2) Make the proper input and output wire
connections for each unit.
3) Connect the speaker wires of the wiring
harness.
4) Connect the wiring harness wires in the
following order; ground, battery, ignition.
5) Connect the wiring harness connector to the
unit.
6) Install the unit in your car.
7) Reconnect the ¤ terminal of the battery.
8) Perform the Initial Setup.
See Initial setup (P.8).
Installing the unit
Ñ Non-Japanese cars (DDX9904S)
Bend the tabs of the
mounting sleeve
with a screwdriver
or similar utensil and
attach it in place.
Ñ Japanese cars
6 or 7
NOTE
• Make sure that the unit is installed securely in
place. If the unit is unstable, it may malfunction
(eg, the sound may skip).
Car Bracket
6 or 7
Ñ Trim plate (DDX9904S)
1) Attach accessory 8 to the unit.
8
85English
Page 86
Connection/Installation
Ñ GPS antenna
GPS antenna is installed inside of the car. It
should be installed as horizontally as possible
to allow easy reception of the GPS satellite
signals.
To mount the GPS antenna inside your vehicle:
1) Clean your dashboard or other surface.
2) Remove the separator of the metal plate
(accessory 0).
3) Press the metal plate (accessory 0) down
firmly on your dashboard or other mounting
surface. You can bend the metal plate
(accessory 0) to conform to a curved surface,
if necessary.
4) Remove the separator of the GPS antenna
(accessory 9), and stick the antenna to the
metal plate (accessory 0).
9
0
NOTE
• Depending on the type of car, reception of the
GPS satellite signals might not be possible with
an inside installation.
• Please install this GPS antenna in an area away
from any antennas that are used with CB radios or
satellite televisions.
• The GPS antenna should be installed at a position
that is spaced at least 12 inch (30 cm) from
cellular phone or other transmitting antennas.
Signals from the GPS satellite may be interfered
with by these types of communication.
• Painting the GPS antenna with (metallic) paint
may cause a drop in performance.
Ñ Microphone unit
1) Check the installation position of the
microphone (accessory 4).
2) Clean the installation surface.
3) Remove the separator of the microphone
(accessory 4), and stick the microphone to
the place shown below.
4) Wire the microphone cable up to the unit
with it secured at several positions using tape
or other desired method.
5) Adjust the direction of the microphone
(accessory 4) to the driver.
4
Fix a cable with a commercial item of tape.
86
Page 87
Connection/Installation
Ñ Removing the trim plate
(DDX9904S)
1) Engage the catch pins on the extraction key
(accessory 5) and remove the two locks on
the lower level.
Lower the trim plate (accessory 8) and pull it
forward as shown in the figure.
8
5
Catch
Lock
NOTE
• The trim plate can be removed from the top side
in the same manner.
2) When the lower level is removed, remove the
upper two locations.
Ñ Removing the unit (DDX9904S)
1) Remove the trim plate by referring to step 1 in
"Removing the trim plate".
2) Insert the two extraction key (accessory 5)
deeply into the slots on each side, as shown.
5
3) Lower the extraction key toward the bottom,
and pull out the unit halfway while pressing
towards the inside.
NOTE
• Be careful to avoid injury from the catch pins on
the extraction key.
4) Pull the unit all the way out with your hands,
being careful not to drop it.
87English
Page 88
Connection/Installation
Ñ Connecting wires to terminals
Fuse (15A)
Connect to the vehicle’s
parking brake detection switch
harness.
PRK SW
Ignition key switch
Car fuse box
Battery
Green/White
CAM–
Green/Red
CAM+
To CMOS-3xx series (Optional Accessory) camera
control terminal
Purple/White
(Reverse sensor wire) (2 m)
REVERSE
Connect to vehicle’s reverse lamp harness when
using the optional rear view camera.
Light Green
(Parking sensor wire)
(2 m)
For best safety, be sure to
connect the parking sensor.
ACC
Black
(Ground wire) ¤
(To car chassis)
Accessory 1
Red
(Ignition wire)
Yellow
(Battery wire)
White
White/Black
Gray
Gray/Black
Green
Green/Black
Purple
Purple/Black
If no connections are made, do not let
the cable come out from the tab.
Blue/White
(Power control wire)
Speaker impedance: 4-8 Ω
To front left speaker
To front right speaker
To rear left speaker
To rear right speaker
P. CONT
When using the optional power amplifier,
connect to its power control terminal. (Max.
200mA, 12V)
Light Blue/Yellow
(Steering remote control wire)
To steering remote
To use the steering wheel remote control
feature, you need an exclusive remote
adapter (not supplied) matched to your car.
Orange/White
(Dimmer control wire)
To car light control switch
Blue
(Antenna control wire)
Depending on what antenna you are using,
connect either to the control terminal of the
motor antenna, or to the power terminal for
the booster amplifier of the film-type antenna.
(Max. 300mA, 12V)
REMOTE CONT
STEERING WHEEL
REMOTE INPUT
ILLUMI
ANT CONT
88
Page 89
Connection/Installation
Ñ Connecting the system and
external components
12
9
1
2
34
AV Audio output (ø3.5 mini jack)
1
FM/AM antenna input
2
When connecting to an external amplifier,
3
connect its ground wire to the car’s chassis to
avoid damaging the unit.
Rear Audio Preout
(Left; White, Right; Red)
Front Audio Preout
(Left; White, Right; Red)
Subwoofer Preout
(Left; White, Right; Red)
SiriusXM Connect Vehicle Tuner connector
4
iDatalink connector
5
AV-IN (CA-C3AV; Optional Accessory) input
6
Dashboard camera interface
7
Connect a Dashboard Camera DRV-N520
(optional accessory). ( P.90)
Accessory 9: GPS Antenna
8
11
10
Front view camera/ Dashboard camera input
11
(Yellow)
Visual Output (Yellow)
12
Ñ Connecting a USB device
Accessory 3 (Gray) (1 m)
5678
[1]
Accessory 2 (Black) (1 m)
USB device
[2]
USB (Gray) terminal
USB (Black) terminal
USB maximum power supply current :
DC 5 V = 1.5 A
[2]
Sold separately / Use CA-U1EX to extend the
cable if necessary. (Max 500 mA, 5V)
[3]
See Securing the USB extension cable
(P. 89).
[3]
[3]
[1]
[1]
Ñ Securing the USB extension
cable
Secure the USB extension cable with insulating
tape or the like so that its connectors are not
disconnected.
Accessory 4: Bluetooth Microphone
9
Rear view camera input (Yellow)
10
89English
Page 90
Connection/Installation
Ñ Connecting an iPod/iPhone
● Lightning connector
iPod/iPhone
KCA-iP103 (0.8m)
KCA-iP103 (0.8m)
[1]
USB maximum power supply current :
DC 5 V = 1.5 A
[2]
Sold separately
[3]
Optional accessory
[4]
See Securing the USB extension cable
(P. 89).
[3]
Accessory 3 (Gray) (1 m)
Accessory 2 (Black) (1 m)
USB (Gray) terminal
USB (Black) terminal
[1]
[1]
iPhone (with CarPlay)
[3]
[4]
Ñ Connecting an Android
smartphone
[2]
Micro USB to USB cable
[4]
Accessory 2 (Black) (1 m)
USB (Gray) terminal
USB (Black) terminal
[1]
USB maximum power supply current :
Android smartphone
[2]
Accessory 3 (Gray) (1 m)
[3]
[1]
[1]
DC 5 V = 1.5 A
[2]
Sold separately
[3]
See Securing the USB extension cable
[2]
(P. 89).
[2]
[3]
Ñ Connecting a Dashboard
camera
Front view camera/
DRV-N520
[1]
Dashboard camera input
(Yellow)
90
[1]
Optional accessory
Dashboard camera interface
Page 91
Troubleshooting
Troubleshooting
Problems and Solutions
If any trouble occurs, first check the following
table for possible problems.
NOTE
• Some functions of this unit may be disabled by
some settings made on this unit.
• What might seem to be a malfunction in your
unit may just be the result of slight misoperation
or miswiring.
Ñ About settings
• Cannot set up the subwoofer.
• Cannot set up subwoofer phase.
• No output from the subwoofer.
• Cannot set up the low pass filter.
• Cannot set up the high pass filter.
Subwoofer is not set to on.
Set the subwoofer to on. See Speaker/ X’over
setup (P.72).
The dual zone function is enabled.
Set the dual zone function to off. See Zone Control
(P. 75).
• Cannot select the output destination of the
subsource in the dual zone.
• Cannot adjust the volume of the rear speakers.
The dual zone function is disabled.
Set the dual zone function to on. See Zone Control
(P. 75).
• Cannot set up the equalizer.
• Cannot set up the crossover network.
The dual zone function is enabled.
Set the dual zone function to off. See Zone Control
(P. 75).
Ñ About audio operations
Radio reception is poor.
The car antenna is not extended.
Pull out the antenna all the way.
The antenna control wire is not connected.
Connect the wire correctly. See Connecting the
system and external components (P.89).
Cannot select a folder.
The random play function is enabled.
Turn off the random function.
Cannot perform repeat play during VCD playback.
The PBC function is enabled.
Turn off the PBC function.
The specified disc does not play, but another one
plays instead.
The disc is quite dirty.
Clean the disc. See Precautions on handling discs
(P. 4).
The disc is severely scratched.
Try another disc instead.
The sound skips when an audio file is being
played.
The disc is scratched or dirty.
Clean the disc. See Precautions on handling discs
(P. 4).
The recording condition is bad.
Record the file again or use another disc.
Ñ Other
The Touch Sensor Tone doesn’t sound.
The preout jack is being used.
The Touch Sensor Tone cannot be output from the
preout jack.
Android smartphon operation is slow.
This occurs when multiple applications are started on
the Android smartphone.
For details, see Caution for Smartphone Users
(P. 5).
Error Messages
When you fail to operate the unit correctly, the
cause of the failure appears as the message on
the screen.
here is an error in the speaker wiring. Please check
the connections.
Protective circuit has been activated because a speaker
cord has shorted or it has come in contact with the car
chassis.
Wire or insulate the speaker cord as appropriate and
turn the power off and on again.
Hot Error
When the internal temperature of this unit rises to 60°C
or more, the protection circuit is activated and you may
not be able to operate the unit.
Use the unit again after reducing the temperature
of the unit.
Mecha Error
The disc player is malfunctioning.
Eject the disc and try inserting it again. Contact the
KENWOOD dealer if this indicator continues blinking
or the disc cannot be ejected.
91English
Page 92
Troubleshooting
Disc Error
An unplayable disc is inserted.
Change the disc. See Playable Media and Files
(P. 93).
Read Error
The disc is quite dirty.
Clean the disc. See Precautions on handling discs
(P. 4).
Disc is upside down.
Load the disc with the labeled side up.
Region Code Error
The disc you wanted to play has a region code that
cannot be played with this unit.
See Region Codes in the World (P.95) or try
another disc.
Error 07–67
The unit is not operating correctly due to some reason
or other.
Turn the power off and on again. If the “Error 07−67”
message does not disappear, see your nearest
KENWOOD dealer.
No Device (USB device)
The USB device is selected as a source although no USB
device is connected.
Change the source to any source other than USB/
iPod. Connect a USB device, and change the source
to USB again.
Disconnected (iPod, Bluetooth audio player)
The iPod/Bluetooth audio player is selected as a source
although no iPod/Bluetooth audio player is connected.
Change the source to any source other than iPod/
Bluetooth. Connect an iPod/Bluetooth audio player,
and change the source to iPod/Bluetooth again.
No Media file
The connected USB device contains no playable audio
file. Media was played that doesn’t have data recorded
that the unit can play.
See Playable Media and Files (P.93) and try
another USB device.
USB device over current status detected.
The connected USB device is rated a current capacity
higher than the allowable limit.
Check the USB device. Some trouble may have
occurred to the connected USB device.
Change the source to any source other than USB.
Remove the USB device.
Ñ SiriusXM
Check Tuner
A SiriusXM tuner is not connected to this unit.
Verify that the SiriusXM Connect Vehicle Tuner cable
is securely connected to the radio.
Subscription Updated - Press Return To Continue
The SiriusXM subscription has been renewed.
Pressing the Control knob will clear the message.
SXM Chan Unavailable
The currently selected channel is unavailable.
—
SXM Ch Unsubscribed
The currently selected channel is not subscribed to.
—
SXM Check Antenna
No antenna is connected to the SiriusXM tuner.
Check that an antenna is connected to the SiriusXM
tuner. Check antenna for damages.
SXM No Signal
No SiriusXM radio signal is received.
Verify that your vehicle is outdoors with a clear view
of the sky.
Channel Locked
The selected channel has been locked by the parental
controls.
Enter the unlock code when you are asked. See
Parental Control (P.49).
Incorrect Pass Code entered
The selected channel is a mature or parental lock
channel, and locked by the parental lock or user lock
code.
Enter the correct lock code.
92
Page 93
Appendix
Playable Media and Files
You can play various kinds of media and files on this unit.
Ñ List of playable discs (DDX9904S/ DDX9704S)
Disc types / StandardSupportRemark
DVDDVD Video
DVD Audio×
DVD-VR×
1
DVD-R*
DVD-RW
DVD+R
DVD+RW
DVD-R DL (Dual layer)
DVD+R DL (Double layer)
DVD-RAM×
CDMusic CD*
OthersDualdisc×
v : Playback is possible.
r : Playback is partly possible.
× : Playback is impossible.
1
CD-ROM
CD-R
CD-RW
DTS-CD×
Video CD (VCD)
Super video CD×
Photo CD×
CD-EXTRA
HDCD
CCCD×
Super audio CD
■ Use of DualDisc
When playing a “DualDisc” on this unit, the surface
of the disc that is not played may be scratched
while the disc is inserted or ejected. Since the music
CD surface does not conform to the CD standard,
playback may be impossible.
(A “DualDisc” is a disc with one surface containing
DVD standard signals and the other surface
containing music CD signals.)
• If music of normal CD and other playback systems are recorded in the same disc, only the playback system
recorded at the first setout is played.
• WMA and AAC of which is covered with DRM cannot be played.
• DSD sound is converted to PCM sound before playback.
• The EmChinks tag of DSDIFF is not supported.
• Although the audio files are complied with the standards listed above, the play may be impossible depending on
the types or conditions of media or device.
WMV (.wmv) Main Profile1920 × 1080 (30 fps)8 MbpsWMA
MKV (.mkv)
Baseline Profile,
Main Profile
Profile
Video Format follows H.264/MPEG-4 AVC, MPEG-4, WMV
1920 × 1080 (30 fps)8 MbpsMP3, AAC
1920 × 1080 (30 fps)8 MbpsMP3, AAC
MP3, AAC, WMA, Vorbis,
FLAC
■ Limitation of structure for the file and the folder
Disc media USB device
Maximum number of folder layers88
Maximum number of files (per folder)999999
Maximum number of folders (per folder)50009999
Maximum number of folders (per device)5000–
NOTE
• You can enter a folder name and file name with 255 or fewer single-byte characters.
• Files in the folder whose folder name begins with a dot (.) cannot be played.
94
Page 95
Appendix
Region Codes in the World
The DVD players are given a region code according to the country or area it is marketed, as shown in
the following map.
1
2
1
4
■ DVD disc marks
ALL
Indicates a region number. The discs with this
mark can be played with any DVD player.
8
Indicates the number of audio languages
recorded. Up to 8 languages can be recorded in
a movie. You can select a favorite language.
32
Indicates the number of subtitled languages
recorded. Up to 32 languages can be recorded.
9
If a DVD disc has scenes shot from multiple
angles, you can select a favorite angle.
16:9 LB
Indicates the type of screen for the image. The
left mark indicates that a wide image picture
(16:9) is displayed on a standard TV set screen
(4:3) with a black band at both the top and
bottom of the screen (letter box).
5
6
3
5
2
2
4
■ Operation regulatory marks
With this DVD, some functions of this unit
such as the play function may be restricted
depending on the location where the DVD is
playing. In this case, the following marks will
appear on the screen. For more information,
refer to the disc manual.
Prohibition Mark
■ Discs with limited period of use
Do not leave discs with a limited period of use in
this unit. If you load an already expired disc, you
may not be able to remove it from this unit.
DDX9904S
: 182 × 112 × 163 mm
7-3/16 × 4-7/16 × 6-7/16 inch
DDX9704S
: 178 × 100 × 160 mm
7 × 3-15/16 × 6-5/16 inch
DMX7704S
: 178 × 100 × 155 mm
7 × 3-15/16 × 6-1/8 inch
Operational Temperature Range
: -10 °C – +60 °C
Weight
DDX9904S/ DDX9704S
: 2.4 kg (5.29 lbs)
DMX7704S
: 1.7 kg (3.75 lbs)
NOTE
• Although the effective pixels for the liquid crystal
panel is given as 99.99% or more, 0.01% of pixels
may not light or may light incorrectly.
Specifications subject to change without notice.
About this Unit
■ Copyrights
• The Bluetooth® word mark and logos are registered
trademarks owned by Bluetooth SIG, Inc. and any
use of such marks by JVC KENWOOD Corporation is
under license. Other trademarks and trade names are
those of their respective owners.
• Manufactured under license from Dolby Laboratories.
Dolby, Dolby Audio and the double-D symbol are
trademarks of Dolby Laboratories.
•
• This item incorporates copy protection technology
• The “AAC” logo is a trademark of Dolby Laboratories.
• “Made for iPod” and “Made for iPhone” mean that an
• iPhone, iPod, iPod classic, iPod nano, and iPod touch
• Apple, Siri, Apple CarPlay and Apple CarPlay logo are
• Sirius, XM and all related marks and logos are
• HD Radio Technology manufactured under license
• PANDORA, the PANDORA logo, and the Pandora
• SPOTIFY and the Spotify logo are among the
• Android, Android Auto, Google Play and other marks
• BlackBerry®, RIM®, Research In Motion® and related
is a trademark of DVD Format/Logo
Licensing Corporation registered in the U.S., Japan
and other countries.
that is protected by U.S. patents and other
intellectual property rights of Rovi Corporation.
Reverse engineering and disassembly are prohibited.
electronic accessory has been designed to connect
specifically to iPod, or iPhone, respectively, and
has been certified by the developer to meet Apple
performance standards. Apple is not responsible for
the operation of this device or its compliance with
safety and regulatory standards. Please note that the
use of this accessory with iPod, or iPhone may affect
wireless performance.
are trademarks of Apple Inc., registered in the U.S.
and other countries.
trademarks of Apple Inc., registered in the U.S. and
other countries.
trademarks of Sirius XM Radio Inc. All rights reserved.
from iBiquity Digital Corporation. U.S. and Foreign
Patents. HD Radio™ and the HD, HD Radio, and “Arc”
logos are proprietary trademarks of iBiquity Digital
Corp.
trade dress are trademarks or registered trademarks
of Pandora Media, Inc., used with permission.
registered trademarks of Spotify AB.
are trademarks of Google Inc.
trademarks, names and logos are the property of
Research In Motion Limited and are registered and/
or used in the U.S. and countries around the world.
Used under license from Research In Motion Limited.
99English
Page 100
Appendix
• THIS PRODUCT IS LICENSED UNDER THE AVC
PATENT PORTFOLIO LICENSE FOR THE PERSONAL
USE OF A CONSUMER OR OTHER USES IN WHICH IT
DOES NOT RECEIVE REMUNERATION TO (¡)ENCODE
VIDEO IN COMPLIANCE WITH THE AVC STANDARD
(“AVC VIDEO”) AND/OR (¡¡)DECODE AVC VIDEO
THAT WAS ENCODED BY A CONSUMER ENGAGED
IN A PERSONAL ACTIVITY AND/OR WAS OBTAINED
FROM A VIDEO PROVIDER LICENSED TO PROVIDE
AVC VIDEO. NO LICENSE IS GRANTED OR SHALL
BE IMPLIED FOR ANY OTHER USE. ADDITIONAL
INFORMATION MAY BE OBTAINED FROM MPEG LA,
L.L.C. SEE HTTP://WWW.MPEGLA.COM
• THIS PRODUCT IS LICENSED UNDER THE MPEG4 VISUAL PATENT PORTFOLIO LICENSE FOR
THE PERSONAL AND NON-COMMERCIAL USE
OF A CONSUMER FOR (¡) ENCODING VIDEO IN
COMPLIANCE WITH THE MPEG-4 VISUAL STANDARD
(“MPEG-4 VIDEO”) AND/OR (¡¡) DECODING MPEG4 VIDEO THAT WAS ENCODED BY A CONSUMER
ENGAGED IN A PERSONAL AND NON-COMMERCIAL
ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO
PROVIDER LICENSED BY MPEG LA TO PROVIDE
MPEG-4 VIDEO. NO LICENSE IS GRANTED OR SHALL
BE IMPLIED FOR ANY OTHER USE. ADDITIONAL
INFORMATION INCLUDING THAT RELATING TO
PROMOTIONAL, INTERNAL AND COMMERCIAL USES
AND LICENSING MAY BE OBTAINED FROM MPEG LA,
LLC. SEE HTTP://WWW.MPEGLA.COM.
• THIS PRODUCT IS LICENSED UNDER THE VC-1 PATENT
PORTFOLIO LICENSE FOR THE PERSONAL AND NONCOMMERCIAL USE OF A CONSUMER TO ( i ) ENCODE
VIDEO IN COMPLIANCE WITH THE VC-1 STANDARD
(“VC-1 VIDEO”) AND/OR ( ii ) DECODE VC-1 VIDEO
THAT WAS ENCODED BY A CONSUMER ENGAGED
IN A PERSONAL AND NON-COMMERCIAL ACTIVITY
AND/OR WAS OBTAINED FROM A VIDEO PROVIDER
LICENSED TO PROVIDE VC-1 VIDEO. NO LICENSE IS
GRANTED OR SHALL BE IMPLIED FOR ANY OTHER
USE. ADDITIONAL INFORMATION MAY BE OBTAINED
FROM MPEG LA, L.L.C. SEE HTTP://WWW.MPEGLA.
COM
• libFLAC
Copyright (C) 2000,2001,2002,2003,2004,2005,2006,2
007,2008,2009 Josh Coalson
Redistribution and use in source and binary forms,
with or without modification, are permitted provided
that the following conditions are met:
– Redistributions of source code must retain the
above copyright notice, this list of conditions and
the following disclaimer.
– Redistributions in binary form must reproduce the
above copyright notice, this list of conditions and
the following disclaimer in the documentation
and/or other materials provided with the
distribution.
– Neither the name of the Xiph.org Foundation
nor the names of its contributors may be used to
endorse or promote products derived from this
software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT
HOLDERS AND ONTRIBUTORS ``AS IS’’ AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
FOUNDATION OR CONTRIBUTORS BE LIABLE FOR ANY
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,
OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE
GOODS OR SERVICES; LOSS OF USE, DATA, OR
PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY,
WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING
IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
DAMAGE.
• libvorbis
Copyright (c) 2002-2008 Xiph.org Foundation
Redistribution and use in source and binary forms,
with or without modification, are permitted provided
that the following conditions are met:
– Redistributions of source code must retain the
above copyright notice, this list of conditions and
the following disclaimer.
– Redistributions in binary form must reproduce the
above copyright notice, this list of conditions and
the following disclaimer in the documentation
and/or other materials provided with the
distribution.
– Neither the name of the Xiph.org Foundation
nor the names of its contributors may be used to
endorse or promote products derived from this
software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT
HOLDERS AND CONTRIBUTORS ``AS IS’’ AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
FOUNDATION OR CONTRIBUTORS BE LIABLE FOR ANY
100
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.